Preparation of CdS nanowires by the decomposition of the complex in the presence of microwave irradiation

A novel synthetic route for the preparation of CdS nanowires has been developed. CdS nanowires with a diameter of ca. 4 nm have been successfully prepared by the microwave irradiation of a complex of cadmium-1-pyrrlidine dithio carboxylic acid ammonium (C₅H₁₂N₂S₂, APDTC) [Cd(APDTC)₂]₂ in an ethylenediamine solution. The CdS nanowires were characterized by powder X-ray diffraction pattern, transmission electron microscopy (TEM), UV-Vis spectroscopy, diffuse reflection spectroscopy and PL spectroscopy.     

Oriented growth of benzophenone crystals from undercooled melts

The tin sulfides compounds SnS and SnS₂ nanoflakes were prepared by the microwave-assisted polyol synthetic method. The as-prepared nanoscale flakes were characterized by X-ray powder diffraction, transmission electron microscopy, selected area electron diffraction, X-ray photoelectron spectroscopy and Raman spectra. The influences of solvents and microwave irradiation on the formation of products have been studied.     

Growth and properties of Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 single crystals directly from melt

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by a modified Bridgman method directly from melt using an allomeric Pb[(Mg_1/3Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal as a seed. X-ray diffraction (XRD) measurement confirmed that the as-grown PZNT91/9 single crystals are of pure perovskite structure. Electrical properties and thermal stabilization of PZNT91/9 crystals grown directly from melt exhibit different characters from those of PZNT91/9 crystals grown from flux, although segregation and the variation of chemical composition are not seriously confirmed by X-ray fluorescence analysis (XPS). The [0 0 1]-oriented PZNT91/9 crystals cut from the middle part of the as-grown crystal boules exhibit broad dielectric-response peaks at around 105 °C, accompanied by apparent frequency dispersion. The values of piezoelectric constant d₃₃, remnant polarization P_r, and induced strain are about 1800–2200 pC/N, 38.8 μC/cm², and 0.3%, respectively, indicating that the quality of PZNT crystals grown directly from melt can be comparable to those of PZNT91/9 single crystals grown from flux. However, further work deserves attention to improve the dielectric properties of PZNT crystals grown directly from melt. Such unusual characterizations of dielectric properties of PZNT crystals grown directly from melt are considered as correlating with defects, microinhomogeneities, and polar regions.     

Facile synthesis of submicron BaTiO3 crystallites by a liquid–solid reaction method

Uniform, submicron BaTiO₃ crystallites in tetragonal structure were synthesized by a novel low-temperature liquid–solid reaction method mainly via two simple steps: firstly, BaO₂·H₂O₂ submicron particles of about 130–450 nm were precipitated from the reaction of BaCl₂ and H₂O₂ in a slightly alkaline (pH 8) aqueous solution under the ambient condition; secondly, tetragonal phase BaTiO₃ submicrocrystals with the size in the range of 180 to 400 nm could be produced by subjecting the as-prepared BaO₂·H₂O₂ and commercial TiO₂ submicron particles to thermal treatment in air at 700 °C for 10 h. The as-obtained products were characterized by X-ray powder diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and inductively coupled plasma-atomic emission spectroscopy, and scanning electron microscopy.     

FeNi、NiMnCo及其复合触媒中Ⅰb型金刚石的生长特性

本文以Ni₇₀Mn₂₅Co₅和Fe₆₄Ni₃₆合金及其复合合金作为触媒,采用高温高压温度梯度法在5.6 GPa压力下,对不同温度下沿(100)晶面生长的Ⅰb型金刚石的生长特性进行了研究,研究表明:以Fe₆₄Ni₃₆触媒合成出的金刚石在以(111)晶面为主的晶形高温生长范围内出现了一段约50 K范围的裂晶生长区,而以Ni₇₀Mn₂₅Co₅触媒合成的金刚石在生长温度范围内,特别是在以(111)晶面为主的晶体生长高温区域内容易出现连晶缺陷;高温下Fe₆₄Ni₃₆触媒过度熔融可能是晶体容易产生裂晶的原因,Ni₇₀Mn₂₅Co₅触媒熔体黏性较低可能是容易形成连晶的原因;采用两种触媒复合的方式有效避免了裂晶和连晶的产生;拉曼光谱表征发现连晶的晶体内部质量与单晶的晶体质量相近,裂晶中晶格畸变和杂质较多,晶体内应力较大,复合触媒体系合成的金刚石晶体内应力小,质量好。     

Flux growth of PbMg1/3Ta2/3O3 single crystals

Single crystals of PbMg_1/3Ta_2/3O₃ (PMT) were grown by the flux method. The PbO–Pb₃O₄–B₂O₃ system was used as a solvent. Transparent and light yellow PMT single crystals of rectangular shape and dimensions up to 10×6×4 mm³ were obtained. For the applied growth conditions only, the crystals of the perovskite structure were grown. X-ray diffraction tests showed that at room temperature PMT exhibits cubic symmetry with lattice parameter a=4.042(1) Å. Dielectric studies pointed to relaxor properties of PMT. The characteristic broad and frequency-dependent maximum of dielectric permittivity was observed at 179.7 K (1 kHz).     

Selective-controlled synthesis of one-dimensional strontium phosphates

Anorthic SrHPO₄ nanobelts and hexagonal Sr₁₀O(PO₄)₆ nanorods were obtained by a simple hydrothermal method without adding any surfactant as template. The as-synthesized products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). TEM and HRTEM observations of the products revealed that the as-prepared SrHPO₄ nanobelts and Sr₁₀O(PO₄)₆ hexagonal nanorods are single crystals with their preferential growth direction along the normal of (1 0 0) and (0 0 1) planes, respectively.     

Crystallization behavior and hydrophilic performances of V2O5–TiO2 films prepared by sol–gel dip-coating

Homogeneous and transparent V₂O₅–TiO₂ composite nanometer thin films were prepared on glass substrates by sol–gel processing and dip-coating technique. The films as well as the dried powder of bulk gel were characterized by different techniques like X-ray diffraction (XRD), high-resolution scanning electron microscopy (HRSEM), atomic force microscope (AFM) and thermogravimetry–differential thermal analysis (TG–DTA). The hydrophilicity of the films was determined by measuring the water contact angles on the films. The results showed that the dopant of V₂O₅ on TiO₂ thin films could produce a visible-light response to the films, and the introduction of V₂O₅ could suppress the structural phase transition and crystal growth of TiO₂ crystal. Finally, the relationship between crystalline size and hydrophilicity under sunlight was investigated in this article.     

Controlled synthesis of different morphologies of BaWO4 crystals via a surfactant-assisted method

BaWO₄ crystals with different morphologies, such as nanosheets, nanobelts, flower-like, quadrangled plates and sheaves of dendrite, have been successfully synthesized via PVP as templates. Our result shows that reaction parameters, such as the concentration of PVP aqueous solutions, pH value of the starting solution and molar ratio of [Ba²⁺]/[WO₄²⁻] played important roles in the formation of BaWO₄ crystal with different morphologies. It is obviously different between microwave irradiation heating and oil bath heating. The products were characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy and electron diffraction.     

Flux growth of BPO4 crystals

Single crystals of BPO₄ with sizes up to 15×10×12 mm³ were grown by top-seeded solution growth method using Li₂O–Li₄P₂O₇ as fluxes. The components volatilized from the melt were characterized by the method of X-ray powder diffraction. The defects of grown crystals have also been investigated. The measured ultraviolet cutoff edge of BPO₄ was about 130 nm. Its density was 2.82 g/cm³ determined using drainage method.     

Synthesis, growth, thermal, optical, dielectric and mechanical properties of semi-organic NLO crystal: Potassium hydrogen malate monohydrate

Potassium hydrogen malate monohydrate (PHMM), a semi-organic nonlinear optical material, has been synthesized and single crystals were grown from aqueous solution. Single crystals of PHMM have been grown by slow evaporation of solvent at room temperature up to dimensions of 22 mm×16 mm×14 mm. Single-crystal X-ray diffraction study on grown crystals shows that they belong to monoclinic system and non-centrosymmetry spacegroup Cc. The structural perfection of the grown crystals has been analyzed by high-resolution X-ray diffraction (HRXRD) rocking curve measurements. Fourier transform infrared (FTIR) spectroscopic study was performed for the identification of different modes of functional groups present in the compound. The UV–Vis transmission spectrum has been recorded in the range 200–1100 nm. The thermal stability of the compound has been determined by TG-DTA curves. The dielectric studies were performed. From the microhardness measurements, Vicker's hardness number (H_v), Stiffness constant (C₁₁), fracture toughness (k_c), Brittle index (B_i) and yield strength (σ_y) have been calculated. The Young's modulus was calculated using the Knoop hardness measurement. The SHG relative efficiency of PHMM crystal was found to be 1.2 times higher than that of KDP.     

Textural properties of synthetic nano-calcite produced by hydrothermal carbonation of calcium hydroxide

The hydrothermal carbonation of calcium hydroxide (Ca(OH)₂) at high pressure of CO₂ (initial P_CO2=55 bar) and moderate to high temperature (30 and 90 °C) was used to synthesize fine particles of calcite. This method allows a high carbonation efficiency (about 95% of Ca(OH)₂–CaCO₃ conversion), a significant production rate (48 kg/m³ h) and high purity of product (about 96%). However, the various initial physicochemical conditions have a strong influence on the crystal size and surface area of the synthesized calcite crystals. The present study is focused on the estimation of the textural properties of synthesized calcite (morphology, specific surface area, average particle size, particle size distribution and particle size evolution with reaction time), using Rietveld refinements of X-ray diffraction (XRD) spectra, Brunauer–Emmett–Teller (BET) measurements, and scanning electron microscope (SEM) and transmission electron microscope (TEM) observations. This study demonstrate that the pressure, the temperature and the dissolved quantity of CO₂ have a significant effect on the average particle size, specific surface area, initial rate of precipitation, and on the morphology of calcium carbonate crystals. In contrast, these PTx conditions used herein have an insignificant effect on the carbonation efficiency of Ca(OH)₂.

Finally, the results presented here demonstrate that nano-calcite crystals with high specific surface area (S_BET=6–10 m²/g) can be produced, with a high potential for industrial applications such as adsorbents and/or filler in papermaking industry.     

Growth and characterization of a new nonlinear optical material: Potassium p-nitrophenolate dihydrate (NO2–C6H4–OK·2H2O) with new bonding properties

Single crystals of potassium p-nitrophenolate dihydrate (NPK·2H₂O) have been grown successfully using the isothermal solvent evaporation technique. It is a new semiorganic nonlinear optical crystal, possessing a d_eff of about 1.5 times that of lithium niobate and in which the K⁺ ions are bonded to the nitro group instead of bonding with the phenolic O⁻. Large single crystals of dimension upto 20×6×4 mm³ are harvested within a period of 60 days. The grown crystals are subjected to single crystal X-ray, FTIR and DRS-UV visible spectral, thermal and microhardness analyses. Single crystal X-ray analysis confirms the molecular formula and the structure of the crystal. FTIR spectral studies verify the functional groups present in the crystal. The DRS-UV visible spectrum proved the optical transparency of the crystal in the entire visible and near infrared region. Thermal studies reveal that the crystals are stable upto 180 °C. Microhardness measurements on the cleaved plane (1 1 0) explain the strength and slip direction in the crystal. The SHG efficiency of the crystal is examined by performing the Kurtz powder test using Nd:YAG laser.     

A glass-forming system with compound-forming tendency: As4S6---P4S10

Glasses in the quasi-binary system (As₄S₆)_x(P₄S₁₀)_1−x x = 0.1, …, 1.0, are produced and studied by thermal analysis, X-ray, and Raman spectroscopy. The phase diagram of the system and the critical cooling rate for glass formation both have their maximum at x = 0.5, corresponding to the compound As₂P₂S₈; the X-ray structure of recrystallized samples can be described as a sum of the As₂P₂S₈ (x = 0.5)- and the P₄S₁₀-structure (As₄S₆ not visible); Raman spectra of the glasses are again sums of As₂P₂S₈- and As₄S₆/P₄S₁₀-spectra. All these observations support the assumption that a stable building block corresponding to the 1:1 compound As₂P₂S₈ and surplus As₄S₆ (or P₄₁₀) are the essential elements of the structure in the glasses.     

Simple hydrothermal preparation of -MnOOH nanowires and their low-temperature thermal conversion to β-MnO2 nanowires

Without the use of any extra surfactant or template, γ-MnOOH single crystalline nanowires were synthesized directly through the hydrothermal reaction between KMnO₄ and toluene in distilled water at 180 °C for 24 h; and β-MnO₂ single crystalline nanowires could be obtained just by calcination of the γ-MnOOH nanowires in air at 280 °C for 5 h. The as-prepared γ-MnOOH and β-MnO₂ nanowires were characterized by X-ray powder diffraction, atomic absorption spectroscopy, Fourier transformed infrared spectroscopy, scanning electron microscope, transmission electron microscope, high-resolution transmission electron microscope and selected area electron diffraction.     

Growth and morphology of ruby crystals with unusual chromium concentration

Single crystals of ruby have been obtained from fluxed melts based on the systems Li₂O–MoO₃, Li₂O–WO₃, Na₂O–WO₃, 2PbO–3V₂O₅, PbO–V₂O₅–WO₃, PbF₂–Bi₂O₃ and Na₃AlF₆ by both the TSSG method and spontaneous crystallization at the temperatures 1330–900 °C. Al₂O₃ solubility has been measured for the flux composition of 2Bi₂O₃–5PbF₂ in the temperature range 1200–1000 °C and dissolution enthalpy has been defined as 29.4 KJ/Mol. The composition of grown crystals was studied by electron microprobe analysis. The synthetic ruby contains from 0.51 to 6.38 at% of chromium admixture depending on the crystal growth conditions. Experimental results on growth conditions, composition and morphology of grown crystals are presented for each flux and temperature interval.     

Synthesis of Y2O3:Eu phosphors by bicontinuous cubic phase process

A novel approach for preparation of red-emitting europium-doped yttrium oxide phosphor (Y₂O₃:Eu) by using the bicontinuous cubic phase (BCP) process was reported in this paper. The BCP system was composed of anionic surfactant sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and aqueous yttrium nitrate/europium nitrate solution. Energy dispersive spectrometer analysis revealed the homogeneous precipitation occurred in the BCP structure. Thermogravimetric analysis measurements indicated the precursor powder was europium-doped yttrium hydroxide, Y_1−xEu_x(OH)₃. Scanning electron microscopy micrographs showed the precursor powder had a primary size about 30 nm and narrow size distribution. After heat treatment in furnace above 700 °C for 4 h, high crystallinity Y₂O₃:Eu phosphors was obtained. However, the primary size of particles grew to 50–200 nm and the dense agglomerates with a size below 1 μm were formed. X-ray diffraction patterns indicated the crystal structure of precursor powders and Y₂O₃:Eu phosphors were amorphous and body-centered cubic structure, respectively. The photoluminescence analysis showed that the obtained Y₂O₃:Eu phosphor had a strong red emitting at 612 nm and the quenching started at a Eu concentration of 10 mol%. This study indicated that the BCP process could be used to prepare the highly efficient oxide-based phosphors.     

Phase diagram of the SrS–Ga2S3 system and its application to the single-crystal growth of SrGa2S4

Ce-doped SrGa₂S₄ compound is expected as a new host material of blue EL devices. However, the basic properties of bulk single crystals have not been fully clarified, since this compound has been mostly synthesized in the form of polycrystals or thin films. Here, we firstly present the pseudo-binary phase diagram of the SrS–Ga₂S₃ system constructed in accordance with our DTA data for single-crystal growth of SrGa₂S₄. It is shown that SrGa₂S₄ compound has a congruent melting point and a eutectic reaction in the side of excess of Ga₂S₃ concentration. On the basis of the phase diagram, single crystals of SrGa₂S₄ are grown using Ga₂S₃ as a self-flux in a horizontal Bridgman furnace. Colorless and transparent crystals having a typical size 2×2×2 mm³ are obtained.     

Growth of large dimension BaWO4 crystal by the Czochralski method

In this paper, polycrystalline materials of BaWO₄ were synthesized by solid-state phase method, and a single crystal of BaWO₄ was successfully grown along a and c-axis direction by using the Czochralski method. Up to 20×22×80 mm³ BaWO₄ crystal was obtained, and X-ray powder diffraction results show that the as-grown BaWO₄ crystal belongs to the scheelite structure. The effective segregation coefficients of Ba and W of the BaWO₄ crystal were measured by the X-ray fluorescence method, and the effective segregation coefficients of Ba and W were near 1. The rocking curve from (2 0 0) diffraction plane of as-grown BaWO₄ single crystal was measured on the High-resolution X-ray diffractometer D5005, and the full-width at half-maximum value was found to be 26.64′′ The density and hardness of the BaWO₄ crystal was measured, the measured density was in agreement with the calculated result, and the Mohs hardness was about 4.     

Solvothermal synthesis of K2V3O8 nanorods

A solvothermal route has been developed to synthesize K₂V₃O₈ nanorods via the reduction of V₂O₅ using ethanol as the reducing agent as well as the solvent at 200°C. X-ray diffraction and selected area electron diffraction analysis revealed that the as-synthesized products are of tetragonal structure K₂V₃O₈. Transmission electron spectroscopy image showed that the obtained K₂V₃O₈ comprises rod-like nanocrystallites. The formation mechanism of K₂V₃O₈ was studied.