Application of Functionalized ZnSe Nanoparticles to Determinate Heavy Metal Ions

In this paper, ZnSe nanoparticles, which were modified with mercaptoacetic acid (MAA), worked as novel fluorescence sensors for the quantitative determination of copper(II) and nickel(II). Under the optimal conditions, the fluorescence intensities of functionalized ZnSe nanoparticles were quenched by the addtion of copper(II) or nickel(II) ions, there were linear relationships between the relative fluorescence intensity (logF₀/F) and the concentration in the range of 140–2,000 μg/L for copper(II) (R = 0.9973) and 30–1,000 μg/L for nickel(II) (R = 0.9992), the limits of detection were 50 μg/L and 5 μg/L, respectively.     

Simultaneous Determination of Labetalol and Furosemide by First-Derivative Synchronous Spectrofluorimetry

A rapid, simple and highly sensitive first derivative synchronous spectrofluorimetric method was developed for the simultaneous analysis of a binary mixture of labetalol HCl (LBT) and furosemide (FUR) without prior separation. The method was based upon measuring the first derivative of synchronous fluorescence spectra of the two drugs at Δλ =130 nm in aqueous ethanol (55% V/V). The different experimental parameters affecting the synchronous fluorescence of the studied drugs were carefully studied and optimized. The first derivative amplitude-concentration plots were rectilinear over the range of 0.10 to 1.00 μg/mL and 0.05–0.50 μg/mL with lower detection limits of 0.0149 and 7×10⁻³ μg/mL and quantification limits of 0.045 and 0.021 μg/mL for LBT and FUR, respectively. The proposed method was successfully applied for the determination of the studied drugs in synthetic mixtures. The results obtained were in good agreement with those obtained by the reference methods.     

Second-derivative Synchronous Fluorometric Method for the Simultaneous Determination of Cinnarizine and Domperidone in Pharmaceutical Preparations. Application to Biological Fluids

A rapid, simple and highly sensitive second derivative synchronous fluorometric method has been developed for the simultaneous analysis of binary mixture of cinnarizine (CN) and domperidone (DOM). The method is based upon measurement of the native fluorescence of these drugs at Δλ = 80 nm in aqueous methanol (50% V/V). The different experimental parameters affecting the native fluorescence of the studied drugs were carefully studied and optimized. The fluorescence-concentration plots were rectilinear over the range of 0.1 to 1.3 μg mL⁻¹ and 0.1–3.0 μg mL⁻¹ for CN and DOM, respectively with lower detection limits of 0.017 and 5.77 × 10⁻³ μg mL⁻¹ and quantification limits of 0.058 and 0.02 μg mL⁻¹ for CN and DOM. The proposed method was successfully applied for the determination of the studied compounds in synthetic mixtures and in commercial tablets. The results obtained were in good agreement with those obtained with reference methods. The high sensitivity attained by the synchronous fluorometric method allowed the determination of CN in real and spiked human plasma. The mean % recoveries in case of spiked human plasma (n = 3) were 96.39 ± 1.18 while that in real human plasma (n = 3) was 104.67 ± 4.16.     

Spectrofluorometric Determination of Methocarbamol in Pharmaceutical Preparations and Human Plasma

A simple, sensitive and rapid spectrofluorometric method for determination of methocarbamol in pharmaceutical formulations and spiked human plasma has been developed. The proposed method is based on the measurement of the native fluorescence of methocarbamol in methanol at 313 nm after excitation at 277 nm. The relative fluorescence intensity-concentration plot was rectilinear over the range of 0.05–2.0 μg/mL, with good correlation (r = 0.9999), limit of detection of 0.007 μg/ mL and a lower limit of quantification of 0.022 μg/ mL. The described method was successfully applied for the determination of methocarbamol in its tablets without interference from co-formulated drugs, such as aspirin, diclofenac, paracetamol and ibuprofen, The results obtained were in good agreement with those obtained using the official method (USP 30).The high sensitivity of the method allowed the determination of the studied drug in spiked human plasma with average percentage recovery of 99.42 ± 3.84.     

An Indirect Competitive Fluorescence Immunoassay for Determination of Dicyclohexyl Phthalate in Water Samples

A sensitive and specific indirect competitive fluorescence immunoassays (FIA) has been developed for the quantitative determination of dicyclohexyl phthalate (DCHP) using an antigen-coated plate format. The polyclonal antibodies raised against dicyclohexyl 4-amino phthalate conjugated to bovine serum albumin (BSA) by the amino diazotization linkage method. Antiserum with a sufficiently high titer was generated in rabbits and fluorescein isothiocyanate (FITC) was used as sensitive labels to construct the fluorescence immunoassay (FIA) for measurement of targeted compounds. Under optimized FIA condition, the quantitative working range was from 0.1 to 200 μg L⁻¹ with a limit of detection of 0.05 μg L⁻¹. Other similar phthalate compounds do not interfere significantly in the analysis using this immunoassay technique, and the cross-reactivity rates were less than 10%. Four kinds of water samples (tap water, lake water, river water and leachate) had been detected in this assay, the recovery was 91.3–107.8%. The proposed fluorescence immunoassay turned out to be a powerful tool for monitoring of dicyclohexyl phthalate in water samples at trace level.     

Spectrofluorimetric Determination of Oxamniquine in Dosage Forms and Spiked Human Plasma through Derivatization with 1-dimethylaminonaphthalene-5-sulphonyl chloride

A sensitive, simple and selective spectrofluorimetric method was developed for the determination of oxamniquine (OXM) in pharmaceutical formulations and biological fluids. The method is based on the reaction between the drug and 1-dimethylaminonaphthalene-5-sulphonyl chloride (dansyl chloride) in presence of 0.5 M sodium carbonate (pH 10) to yield a highly fluorescent derivative that is measured at 445 nm after excitation at 335 nm. The different experimental parameters affecting the development and stability of the reaction product were carefully studied and optimized. The fluorescence concentration plot was rectilinear over the range of 0.02–0.2 μg ml⁻¹ with a lower detection limit (LOD) of 0.007 μg ml⁻¹ and limit of quantitation (LOQ) of 0.02 μg ml⁻¹. The proposed method was successfully applied to the analysis of commercial capsules. The results obtained were in good agreement with those obtained using the official spectrophotometric method. Furthermore, the method was applied for the determination of oxamniquine in spiked human plasma, the mean % recovery (n = 4) is 97.77 ± 1.19. A proposal of the reaction pathway was presented.     

Online Monitoring of Bromate in Ozonized Water Without a Previous Separation Process

The use of ozonation for the purification of drinking water can lead to the formation of bromate. The US Environmental Protection Agency and the European Directive for human drinking water has lowered the regulatory level for bromate down to 10 μg l⁻¹, such that methods must be developed for monitoring the formation of bromate, particularly in on-site situations. In the present work we report a fluorometric method for the determination of bromate based on the reaction with carbostyril-124, a compound that shows florescence mainly at pH values above 4 and, when bromated, generates a non-fluorescent product. The reaction can thus be used as an indirect method for determination of the ion. The proposed method, which uses the flow injection (FI) technique, allows online application and kinetic control of the variables affecting the process, together with shorter reaction times, and it provides maximum sensitivity and selectivity. Under optimum conditions, it is possible to determine the analyte within the 4–200 μg l⁻¹ range, with a limit of detection of 0.9 μg l⁻¹ and a relative standard deviation (n = 12, [] = 5 and 30 μg l⁻¹) of 3.2% and 2.6% respectively. The determination rate was ten samples per hour.     

Conventional and First Derivative Synchronous Fluorometric Determination of Ethamsylate in Pharmaceutical Preparations and Biological Fluids. Application to Stability Studies

Two simple, accurate and highly sensitive spectrofluorometric methods were developed for the determination of ethamsylate (ETM). Method I is based on measuring the native fluorescence of ethamsylate in water at 354 nm after excitation at 302 nm. The calibration plot was rectilinear over the range of 0.05–1 μg/mL for ETM with limits of detection and quantitation of 7.9 and 26 ng/mL, respectively. Method II involved synchronous and first derivative synchronous fluorometric methods for the simultaneous determination of ethamsylate (ETM) and hydroquinone (HQ) which is considered as an impurity and/or acidic degradation product. The synchronous fluorescence of both the drug and its impurity were measured in methanol at Δ λ of 40 nm. The peak amplitudes (¹D) were estimated at 293.85 or 334.17 nm for ETM and at 309.05 nm for HQ. Good linearity was obtained for ETM over the ranges 0.1–1.4 μg/mL and 0.1–1.0 μg/mL at 293.85 and 334.17 nm, respectively. For HQ, the calibration plot was rectilinear over the range of 0.01–0.14 μg/mL at 309.05 nm. Limits of detection were 20, 2.01 ng/mL and limits of quantitation were 60, 6.7 ng/mL for ETM and HQ by method II, respectively. Both methods were successfully applied to commercial ampoules and tablets. The results were in good agreement with those obtained by the reference method. Method I was utilized to study the stability of ETM and its degradation kinetics using peroxide. The apparent first-order rate constant, half-life times and activation energy of the degradation process were calculated. Method I was further extended to the in-vitro and in-vivo determination of ETM in spiked and real plasma samples. The mean% recoveries were 99.57 ± 3.85 and 89.39 ± 5.93 for spiked and real human plasma, respectively.     

Synthesis of Functionalized ZnSe Nanoparticles and Their Applications in the Determination of Bovine Serum Albumin

Luminescent quantum dots (QDs)-semiconductor nanocrystals were promising alternative to organic dyes for fluorescence-based applications. In this paper, we developed procedures to use mercaptoacetic acid (MAA) to modify ZnSe nanoparticles and made the nanoparticles to be soluble for the quantitative and selective determination of bovine serum albumin (BSA). Maximum fluorescence intensity was produced at pH 7.0, with excitation and emission wavelengths at 242 and 348 nm, respectively. Under optimal conditions, the straight line equation: ^△ F = 0.38 + 0.34 C (μg/ml) was found between the relative fluorescence intensity and the concentration of BSA in the range of 9.6–124.8 μg/ml, and the limit of detection was 2 μg/ml.     

Hidrogeochemical study in South Amazon region using Photoacoustic Spectroscopy

In this study we demonstrate the usefulness of the Photoacoustic Spectroscopy (PAS) in the investigation of water collected from a natural site located within the Amazon region, Brazil, during the wet to dry seasons transition (May/2006). The water samples were collected from different stages along a hydrologic pathway including precipitation water (Prec), groundwater (GW), through flow water (TF), overland flow water (OF), and stream flow water (SW). The observed photoacoustic spectral features, in the 0.3 to 1.0 μm wavelength region, fall within three distinct bands (C, S, and L). We found band-C, band-S and band-L occurring in the spectral range of 0.30 to 0.40 μm, 0.40 to 0.45 μm and 0.45 to 1.0 μm regions, respectively. The photoacoustic features shift peak positions and change intensities for all samples investigated, thus supporting the proposal of PAS as a useful technique to investigate water samples from natural environments.     

Micelle-Enhanced Spectrofluorimetric Method for Determination of Cholesterol-Reducing Drug Ezetimibe in Dosage Forms

A simple and sensitive spectrofluorimetric method was developed for the determination of ezetimibe in its pharmaceutical formulations. The proposed method is based on investigation of the fluorescence spectral behavior of ezetimibe in sodium dodecyl sulfate (SDS) micellar system. In aqueous solution of acetate buffer pH 5.0, the fluorescence intensity of ezetimibe was greatly enhanced, 200% enhancement, in the presence of SDS. The fluorescence intensity of ezetimibe was measured at 380 nm after excitation at 268 nm. The fluorescence-concentration plot was rectilinear over the range of 0.03–3.0 μg/mL with lower detection limit of 3.08 × 10⁻³ μg/mL. The method was successfully applied to the analysis of ezetimibe in its commercial tablets; the results were in good agreement with those obtained with the reported method. The application of the proposed method was extended to the stability studies of ezetimibe after exposure to different forced degradation conditions, such as acidic, alkaline, photo and oxidative conditions, according to ICH guidelines.     

First Derivative Synchronous Fluorescence Spectroscopy for the Simultaneous Determination of Sulpiride and Mebeverine Hydrochloride in Their Combined Tablets and Application to Real Human Plasma

A rapid, simple and highly sensitive first derivative synchronous fluorometric method has been developed for the simultaneous analysis of binary mixture of sulpiride (SUL) and mebeverine hydrochloride (MEB). The method is based upon measurement of the synchronous fluorescence intensity of these drugs at ∆λ = 100 nm in water. The different experimental parameters affecting the fluorescence of the two drugs were carefully studied and optimized. The fluorescence-concentration plots were rectilinear over the range of 0.05–1 μg/mL and 0.2–3.2 μg/mL for SUL and MEB respectively with lower detection limits (LOD) of 0.006 and 0.01 μg/mL and quantification limits (LOQ) of 0.0.02 and 0.05 μg/mL for SUL and MEB, respectively. The proposed method was successfully applied for the determination of the two compounds in synthetic mixtures and in commercial tablets. The high sensitivity attained by the proposed method allowed the determination of both of SUL and MEB metabolite (veratic acid) in real human plasma samples applying second derivative synchronous fluorometric technique. The mean% recoveries (n = 3) for both MEB metabolite (veratic acid) and SUL were 99.82 ± 2.53 and 98.84 ± 6.20 for spiked human plasma respectively, while for real human plasma, the mean% recoveries (n = 3) were 91.49 ± 4.25 and 91.36 ± 8.46 respectively.     

用三正辛胺-苯萃取分离体系-原子吸收光谱对铬作形态分析

研究了痕量铬形态分析的三正辛胺(TOA)-苯萃取分离体系-原子吸收光谱法。用三正辛胺(TOA)和苯在H₂SO₄介质中把水相中的Cr(Ⅵ)萃入到有机相而Cr(Ⅲ)留在水相中,使两种形态的Cr分离到两相中后对有机相的Cr(Ⅵ)和水相的Cr(Ⅲ)进行AAS测定,可求得Cr(Ⅵ)和Cr(Ⅲ)的含量,该方法对实际水样加标回收率分别在95.0%～102% 和94.8%～103%之间,相对标准偏差分别为2.9%和2.6% ,体系对Cr(Ⅵ)有富集作用,对Cr(Ⅵ)和Cr(Ⅲ)的检出限分别为6.6 μg·L-1和0.20 mg·L-1,TOA对Cr(Ⅵ)的最佳萃取量为4.6 mg·mL-1,该法简单、快速、准确。     

Determination of Cr(III) and Cr(VI) in water by wavelength‐dispersive X‐ray fluorescence spectrometry after preconcentration with an ion‐exchange resin disk

A rapid and simple method using an ion‐exchange resin disk combined with wavelength‐dispersive X‐ray fluorescence (WDXRF) spectrometry was developed for the determination of Cr(III) and Cr(VI) in water. A 100‐ml water sample was first adjusted to pH 3 with nitric acid and then passed through an anion‐exchange resin disk placed on top of a cation‐exchange resin disk at a flow rate of 1 ml min^?1 to separate Cr(III) and Cr(VI). Anionic Cr(VI) was preconcentrated on the upper anion‐exchange resin disk, whereas cationic Cr(III) was preconcentrated on the lower cation‐exchange resin disk. Each ion‐exchange resin disk was dried at 100 °C for 30 min in an electric oven and coated with a commercially available laminate film. The specimens were measured using a WDXRF spectrometer. The calibration curves of Cr(III) and Cr(VI) showed good linearity in the range 1–10 µg. The detection limits corresponding to three times the standard deviation (n = 5) of blank values were 0.17 µg for Cr(III) and 0.16 µg for Cr(VI). If a 1‐l water sample is used, these limits would be 0.17 and 0.16 µg l^?1, respectively. A spike test for 50 µg l^?1 Cr(III) and Cr(VI) in tap water and river water showed quantitative recoveries (94–114%), although this was not observed for mineral drinking water owing to the overlap of V Kβ with Cr Kα. The recovery after overlap correction was satisfactory (115%). Copyright © 2011 John Wiley & Sons, Ltd.     

On the accurate determination of pressure- induced line shifts in the 2ν<Subscript>3</Subscript> band of H<Subscript>2</Subscript>O at 1320 nm

A simple technique is demonstrated for the accurate determination of pressure-induced line shifts of water in air. High- and low-pressure water samples are simultaneously probed on selected overtone transitions at 1.32 μm using a current-modulated distributed-feedback diode laser and harmonic detection. The resultant profiles yield an average line shift of -293±30 MHz/atm for the 3,3,0 (002)2,2,1 (000)transition at 227251 GHz and -134±7 MHz/atm for the 3,2,1 (002)2,1,2 (000) transition at 227027 GHz. Comparisons are made between first- and second-harmonic detection, and wavelength- and frequency-modulation regimes. The effect of modulation broadening on the returned line shifts is quantified. Received: 12 August 2002 / Revised version: 21 October 2002 / Published online: 8 January 2003 RID="*" ID="*"Corresponding author. Fax: +44-01865/275410, E-mail: gus.hancock@chemistry.ox.ac.uk     

微乳液增敏催化光度法测定痕量铬的研究

研究了在微乳液(溴化十六烷基三甲基胺(CTMAB)/正戊醇/正庚烷/水)介质中,痕量铬(Ⅵ)催化过氧化氢氧化茜素红的褪色反应,建立了测定痕量铬的催化动力学新方法。在微乳液体系中,方法的灵敏度比在表面活性剂CTMAB体系中提高了72.5%,催化反应的表观活化能为55.7 kJ·mol-1。水浴温度升高,灵敏度显著提高,校准曲线在不同的反应温度下线性范围不同,在80 ℃反应温度下,线性范围为2.4～75 μg·L-1,检出限达4.27×10-10g·mL-1,相对标准偏差为1.84%(n=11)。该法已应用于电镀废水中铬(Ⅵ)的测定,结果令人满意。     

Spectrofluorimetric Study and Detection of Ketoconazole in the Presence of β-cyclodextrin

The formation of a complex between ketoconazole and β-cyclodextrin was followed by spectrofluorimety. The inclusion of ketoconazole in β-cyclodextrin cavity enhanced the native fluorescence of the drug. The stoichiometry of the complex was 1:1 β-cyclodextrin to ketoconazole and the stability constant of the complex (log K _f) was determined to be 4.3 ± 0.01 at pH = 7.9 and 3.7 ± 0.04 at pH = 2.6. A sensitive spectrofluorimetric method for the detection of ketoconazole is presented. At optimized experimental conditions, a linear relationship between the fluorescence intensity of the solution and concentration of ketoconazole is observed in the range of 0.01–10 μg ml⁻¹ (5 × 10⁻⁸ M–1.88 × 10⁻⁵ M). The method was applied to the detection of ketoconazole in pharmaceutical products and the results were satisfactory in comparison to the official method (relative error = 2.8% and standard deviation = 0.06 for tablets of ketoconazole). The recovery of ketoconazole from a blood serum sample, determined by the proposed method, was 97.1 ± 2.4%.     

Spectrofluorimetric Determination of Etodolac, Moxepril HCl and Fexofenadine HCl Using Europium Sensitized Fluorescence in Bulk and Pharmaceutical Preparations

A simple, selective and sensitive luminescence method has been developed for the assay of etodolac (I), moxepril HCl (II) and fexofenadine HCl (III) in bulk drug and pharmaceutical formulations. The method is based on the luminescence sensitization of europium (Eu³⁺) by complexation with the studied drugs. The fluorescence intensities of the products were measured at 667 nm for (I) and at 615 for (II) and (III) while exciting at 276 for all the studied drugs. The fluorescence intensity was directly proportional to the concentration over the range (20–280), (40–240) and (30–80) ng/ml with limits of detection (LOD) = 0.93, 0.92 and 0.95 μg/ml for drugs I, II and III respectively. Optimum conditions for the formation of the complex in methanol were carefully studied. The proposed method was successfully applied for the assay of the studied drugs in pharmaceutical formulations with excellent recovery.     

Fast Separation Ultra-Performance Liquid Chromatography for Determination of Pre-Column Derivative Abamectin and Ivermectin Residues in Vegetable

A new residue method for quantification of abamectin and ivermectin in vegetable is described in the article. The derivative process is devised that acylating chemical is firstly performed by N-methylimidazole (MI) and trifluoroacetic anhydride (TFAA), then which reacted with hydroxyl function of abamerctin to make fluorescence. The influence of triethylamin (TEA) is examined. Separation is resolute by a short column of 1.7 μm size and operated at high pressure values (10.000 psi). The optimal chromatographic condition and the highest sensitivity are achieved by acetonitrile: water (95: 5), 0.4 mL/min, 0.2 μL injector. The detection limits of abamectin and ivermectin are 1 μg/kg respectively.     

Resonance Scattering Spectral Detection of Catalase Activity Using Au@Ag Nanoparticle as Probe and Coupling Catalase Catalytic Reaction with Fenton Reaction

The Au_coreAg_shell (Au@Ag) nanoparticles in size of 30 nm were prepared using 10 nm gold nanoparticles as seeds at 90°C, and were purified by high-speed centrifugation to remove the excess trisodium citrate to obtain Au@Ag nanoprobe. In the medium of pH 4.0 acetate buffer solution—7.2 μmol/L H₂O₂–67 μmol/L Fe(II), Au@Ag nanoparticles exhibited a resonance scattering (RS) peak at 538 nm. Upon addition of Catalase (Ct), the system produced hydroxyl radical that oxidized the Au@Ag nanoprobe to form the AuAg nanoparticles with partly bare nanogold. Those AuAg nanoparticles aggregated to large nanoclusters that led to the RS peak wavelength red-shift and its RS peak intensity enhanced. The catalase activity (C) is linear to the enhanced RS intensity (ΔI) in the range of 6 to 2,800 U/L, with regression equation of ΔI = 0.168 C-0.2, the correlation coefficient of 0.9952, and detection limit of 2.8 U/L. This method was applied to the detection of serum samples, and the results were agreement with that of the spectrophotometry. A new catalytic mechanism of catalase was proposed with oxywater principle that was agreement with the results of resonance scattering spectroscopy, absorption spectrophotometry, transmission electron microscopy and laser scattering.