射频超导腔加速性能的改进

 为提高超导加速腔的加速梯度和Q值，改进了薄膜型超导腔的加速性能。研究证明，对于铜铌溅射腔，在无氧铜衬底和铌膜之间加入NbN 层可以提高铌膜的超导转变温度，改善晶格结构；对纯铌超导腔提出了改进方法，在传统的纯铌超导腔表面制备多层的超导-绝缘-超导复合膜可以屏蔽Nb腔表面的界面场，提高超导腔的临界磁场，从而提高了铌腔的加速梯度。     

射频超导腔加速性能的改进

为提高超导加速腔的加速梯度和Q值,改进了薄膜型超导腔的加速性能。研究证明,对于铜铌溅射腔,在无氧铜衬底和铌膜之间加入NbN 层可以提高铌膜的超导转变温度,改善晶格结构;对纯铌超导腔提出了改进方法,在传统的纯铌超导腔表面制备多层的超导-绝缘-超导复合膜可以屏蔽Nb腔表面的界面场,提高超导腔的临界磁场,从而提高了铌腔的加速梯度。     

回旋加速器高频腔的设计与分析

根据正电子发射断层显像(PET)回旋加速器的物理要求与实际情况,确定了PET回旋高频双腔体的具体设计方案。在加速电压比较高的要求下,充分利用有限的空间,设计1/4波长线的异型覆面的竖腔结构腔体,采用短路片与移动电容板双调谐结构,满足了频率调谐要求;同时获得较高的品质因数,达到了物理设计要求的加速电压。利用Microwave Studio CST程序对腔体的Q0值、热分布、功率损耗、微调电容做了详细的分析与计算;对实际测量值与仿真计算值进行了对比,并对产生的误差进行了分析和讨论。腔体电压实际测量值达到50 kV以上,频率稳定度达到设计指标1.010-6/d。;     

溅射方法干式处理超导加速腔表面的研究与分析

详细研究了利用超高真空氩离子清洗技术发展的一种超导铌腔表面的“干式”处理方法,从微观和宏观角度分析了溅射处理对铌的表面特性和对超导腔性能的影响.与传统的“湿式”处理方法(化学抛光BCP和电抛光EP)相比,干式处理方法具有结构简单、容易控制、没有污染等优点,是一种很有潜力的超导腔处理方法,可以提高超导腔的性能. 关键词： 超导加速腔 溅射 形貌分析 残留电阻比RRR     

Study and design of RF coupler for Chinese ADS HWR superconducting cavity

An RF power coupler is a key component of the superconducting accelerating system in Chinese ADS proton linac injector I, which is used to transmit 15 kW RF power from the power source to the superconducting HWR cavity. According to the requirement of working frequency, power level, transmission capability and cooling condition, the physics design of coupler has been finished, which includes RF structure optimization, thermal simulation, thermal stress analysis and so on. Based on this design, the prototype of HWR coupler has been fabricated, and it has successfully passed the high power test.     

Study and design of RF coupler for Chinese ADS HWR superconducting cavity

An RF power coupler is a key component of the superconducting accelerating system in Chinese ADS proton linac injector I, which is used to transmit 15 kW RF power from the power source to the superconducting HWR cavity. According to the requirement of working frequency, power level, transmission capability and cooling condition, the physics design of coupler has been finished, which includes RF structure optimization, thermal simulation, thermal stress analysis and so on. Based on this design, the prototype of HWR coupler has been fabricated, and it has successfully passed the high power test.     

Study on the RF performance of 2-cell superconducting cavity

The physical design of the 2-cell superconducting cavity is presented. The RF parameters of the cavity and HOMs （high order modes） are reported. In this paper, we put the emphasis on the analysis of the HOMs and interaction between beam and cavity.     

Study on the RF performance of 2-cell superconducting cavity

The physical design of the 2-cell superconducting cavity is presented.The RF parameters of the cavity and HOMs (high order modes) are reported.In this paper,we put the emphasis on the analysis of the HOMs and interaction between beam and cavity.     

Electron bunch train excited higher-order modes in a superconducting RF cavity

Higher-order mode(HOM) based intra-cavity beam diagnostics has been proved effective and convenient in superconducting radio-frequency(SRF) accelerators.Our recent research shows that the beam harmonics in the bunch train excited HOM spectrum,which have much higher signal-to-noise ratio than the intrinsic HOM peaks,may also be useful for beam diagnostics.In this paper,we will present our study on bunch train excited HOMs,including a theoretical model and recent experiments carried out based on the DC-SRF photoinjector and SRF linac at Peking University.     

A coaxial HOM coupler for a superconducting RF cavity and its low-power measurement results

A resonant buildup of beam-induced fields in a superconducting radio frequency (RF) cavity may make a beam unstable or a superconducting RF cavity quench. Higher-order mode (HOM) couplers are used for damping higher-order modes to avoid such a resonant buildup. A coaxial HOM coupler based on the TTF (TESLA Test Facility) HOM coupler has been designed for the superconducting RF cavities at the Proton Engineering Frontier Project (PEFP) in order to overcome notch frequency shift and feed-through tip melting issues. In order to confirm the HOM coupler design and finalize its structural dimensions, two prototype HOM couplers have been fabricated and tested. Low-power testing and measurement of the HOM couplers has shown that the HOM coupler has good filter properties and can fully meet the damping requirements of the PEFP low-beta superconducting RF linac.     

A coaxial HOM coupler for a superconducting RF cavity and its low-power measurement results

A resonant buildup of beam-induced fields in a superconducting radio frequency(RF)cavity may make a beam unstable or a superconducting RF cavity quench. Higher-order mode(HOM)couplers are used for damping higher-order modes to avoid such a resonant buildup. A coaxial HOM coupler based on the TTF (TESLA Test Facility)HOM coupler has been designed for the superconducting RF cavities at the Proton Engineering Frontier Project(PEFP)in order to overcome notch frequency shift and feed-through tip melting issues. In order to confirm the HOM coupler design and finalize its structural dimensions, two prototype HOM couplers have been fabricated and tested. Low-power testing and measurement of the HOM couplers has shown that the HOM coupler has good filter properties and can fully meet the damping requirements of the PEFP low-beta superconducting RF linac.     

Design and simulation of a new type of 500 MHz single-cell superconducting RF cavity

This paper illustrates the design and simulation of a unique 500 MHz single-cell superconducting radio frequency cavity with a fluted beam pipe and a coaxial-type fundamental power coupler. The simulation results show that the cavity has a high r/Q value, a low peak surface field and a large beam aperture, so it can be a candidate cavity for high current accelerators. With the help of a fluted beam tube, almost all the higher order modes can propagate out of the cavity, especially the first two dipole modes, TE₁₁₁ and TM₁₁₀, and the first higher monopole mode, TM₀₁₁. The external quality factor of the coaxial fundamental power coupler is optimized to 1.2×10⁵, which will be useful when it is applied in the light source storage ring.     

RF cavity for gas laser excitation

Summary A new technique for RF transverse excitation of gas laser has been tested: the plasma tube has been put inside a quarter wave strip line RF cavity. Excellent field uniformity and arcing problem avoidance have been observed. The efficiency is greater than 15%. The guidelines for cavity design are discussed. Work partially supported by ENEA-Contract No. C/451 (Dip. Fusione Associazione EURATOM-ENEA, CRE Frascati).     

RF properties of superconducting vanadium

Q values of a superconducting vanadium cavity in theT E ₀₁₁ mode at 9.6 GHz were measured to determine the residual surface resistanceR ₀ and the reduced energy gap 2(0)/kT _c with respect to different surface treatments such as electropolishing, oxipolishing and anodizing. The residual surface resistance was found to be lowest for the oxipolished cavity, corresponding to a residualQ of 2×10⁸ at 1.2 K. Independent of the surface treatment the reduced energy-gap value amounted to 3.52±0.1. The influence of different vanadium oxides on the rf properties of superconducting vanadium was investigated.     

Magnetic system of a superconducting separated-sector cyclotron for hadron therapy

The development of a cyclotron magnetic system based on superconducting sector magnets is discussed. The cyclotron is conceived as a booster accelerator of a source of ¹²С⁶⁺ ions with energy of 400MeV/nucleon for the purposes of hadron therapy. The results of preliminary investigations aimed at developing such a facility have been reported in our previous papers. In this paper, we consider various configurations of the booster’s magnetic system for various field levels. We also analyze the effects of the positions and shapes of superconducting coils on the magnetic field and select the optimum configuration for the cyclotron’s magnetic system.     

Recent progress on RF superconducting cavities

RF superconducting （SRF） cavities can work in continuous wave mode or long pulse mode. SRF technology has been developing rapidly since the end of the last century. RF superconducting technology is widely used in particle accelerators around the world. As the key elements, research on superconducting cavities is carried out worldwide. Besides Europe, the United States and Japan, many countries have already started SRF projects, such as Canada, India, Korea, etc. Great improvements on SRF technology have been made in China in recent years. Progress in SRF cavities is introduced in this paper.     

Recent progress on RF superconducting cavities

RF superconducting (SRF) cavities can work in continuous wave mode or long pulse mode.SRF technology has been developing rapidly since the end of the last century.RF superconducting technology is widely used in particle accelerators around the world.As the key elements, research on superconducting cavities is carried out worldwide.Besides Europe, the United States and Japan, many countries have already started SRF projects, such as Canada, India, Korea, etc.Great improvements on SRF technology have been made in China in recent years.Progress in SRF cavities is introduced in this paper.     

C++QED: an object-oriented framework for wave-function simulations of cavity QED systems

We present a framework for efficiently performing Monte Carlo wave-function simulations in cavity QED with moving particles. It relies heavily on the object-oriented programming paradigm as realised in C++, and is extensible and applicable for simulating open interacting qua ntum dynamics in general. The user is provided with a number of “elements”, e.g. pumped moving particles, pumped lossy cavity modes, and various interactions to compose complex interacting systems, which contain several particles moving in electromagnetic fields of various configurations, and perform wave-function simulations on such systems. A number of tools are provided to facilitate the implementation of new elements.     

加速器高频D电路Q值的计算与测量

 介绍了回旋加速器高频单D型盒D电路Q值的计算与测量方法。重点对Q值的理论计算进行推导，并对计算原理进行说明。然后对计算结果和测量结果进行比较。得出的计算和测量结果基本吻合。误差产生的主要原因是计算过程中的近似和短路片接触电阻的取值，其中短路片接触电阻是一个重要因素，在设计腔体时应引起足够的重视。     

Design and research of RF system for 10 MeV compact cyclotron

A 10 MeV compact cyclotron (CYCHU-10) has been developing in Huazhong University of Science and Technology (HUST). The RF system includes a 10 kW RF power generator and a resonance cavity. There is no automatic frequency tuning equipment in the cavity due to space limitations, so the generator must search and track the cavity resonant frequency. AD9850 synthesizer is used to generate RF signal in the experimental prototype, and a fine sinusoidal waveform around 99 MHz is obtained with the method of picking up a special aliased signal from the synthesizer’s output, and the output power level can be set by regulating the resistor connected to the Pin ‘R _set’. The final stage amplifier based on tetrode operates in the grounded cathode configuration, and the schematic of the tetrode circuit is illustrated. The method of searching the resonant frequency is discussed in detail. For the sake of a compact and robust structure, the resonance cavity will adopt non-uniform characteristic impedance coaxial structure, and the magnet surface electroplated with copper will be used as dummy Dees. The precise shapes and dimensions of the cavity are designed and simulation results are carried out in this paper. The distributions of electromagnetic field are illustrated by means of numerical calculation analysis, and the wooden model test is preformed as well.