Preparation of nanostructured thin films of yttrium iron garnet (Y<Subscript>3</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript>) by sol–gel technology

The synthesis of hydrolytically active heteroligand coordination compounds [M(C₅H₇O₂)_3?x(C₅H₁₁Oⁱ)_x] (M = Fe³⁺ and Y³⁺) using iron and yttrium acetylacetonates has been studied. The gel formation kinetics in solutions of these compounds upon hydrolysis and polycondensation has also been studied. Thin films of a solution of these precursors have been applied to polished sapphire substrates by dip coating technology. The crystallization of nanostructured yttrium iron garnet (Y₃Fe₅O₁₂) films during heat treatment of xerogel coatings under various conditions has been studied. How the phase composition, microstructure, and particle size depend on the synthesis parameters has been recognized.     

Synthesis and microwave dielectric properties of Ca<Subscript>0.6</Subscript>La<Subscript>0.267</Subscript>TiO<Subscript>3</Subscript> nanocrystalline powders by sol–gel method

Ca_0.6La_0.267TiO₃ nanocrystalline powders were successfully synthesized by the sol–gel method using PEG1000 as a dispersant in this study. The sinterability of the powders and the microwave dielectric properties of the ceramics were also investigated. The XRD diffraction result showed that pure Ca_0.6La_0.267TiO₃ powder with orthorhombic perovskite structure could be synthesized at 600 °C for 2 h without any detectable intermediate phase. The average grain size of the as-synthesized powder was as low as 35 nm. Compared with Ca_0.6La_0.267TiO₃ ceramics fabricated by conventional solid-state process, the bulk materials prepared by sintering as-prepared nanopowders performed better in densification and microwave dielectric properties. The ceramics sintered at 1,300 °C exhibited a higher relative density of 98.3% combined with a dielectric constant (ε _r ) of 120.3, a quality factor (Q × f) of 23,550 GHz and a temperature coefficient of resonant frequency (τ _f ) of +220.7 ppm/°C, respectively.     

Synthesis and morphology of Ba(Zr<Subscript>0.20</Subscript>Ti<Subscript>0.80</Subscript>)O<Subscript>3</Subscript> powders obtained by sol–gel method

Barium zirconate titanate, Ba(Zr_0.20Ti_0.80)O₃ (BZT) powders were prepared by sol–gel method. These powders were characterized by thermogravimetric and differential thermogravimetric analyses (TG-DTA), X-ray diffraction (XRD) and microcopy electron transmission (TEM). The decomposition of the precursors was monitored by TG-DTA. XRD patterns reveal that BZT powders heat treated at 800 °C present single phase with perovskite-type cubic structure. TEM micrographs were employed to estimate the average particle size of the BZT powders (≈ 20 nm). The results indicate that the particle size of the BZT powders increases with the increasing of the holding time and aging temperature. The low aging temperature can reduce the agglomeration of the nanopowders. Three polyalcohols were employed as surfactants in sol–gel method: butanol (BTOL), polyethylene glycol (PEG) and polyvinyl alcohol (PVA). It is noted that PEG has a better effect on reducing agglomeration of BZT powders than that of the BTOL and PVA.     

Structure and electrorheological properties of nanoporous BaTiO<Subscript>3</Subscript> crystalline powders prepared by sol–gel method

In this paper, a novel nanoporous barium titanate (BaTiO₃) crystalline powder was synthesized by using triblock poly(ethylene oxide) (PEO) and poly(propylene oxide) (PPO) based systems (P-123) as the soft template via a sol–gel method and their structure-dependent electro rheological property was studied. The pore diameter and specific surface area of BaTiO₃ were precisely controlled by varing the calcined temperature. The chemical composition, structure and surface morphology of BaTiO₃ were characterized by X-ray diffraction (XRD), thermo gravimetric analysis (TGA), and nitrogen adsorption–desorption method, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The result revealed that the pore volume and specific surface area of BaTiO₃ decreased with the increment of calcined temperature. The electro rheological fluids (ERFs) were obtained by dispersing BaTiO₃ crystallites in silicon oil and three kinds ERFs were fabricated by using three kinds of BaTiO₃ which were prepared under different calcined temperature (550, 600 and 900 °C) as the precursors. The behaviors of the ERFs were evaluated via a rotational rheometer fixed with electric field generator. The results showed that electro rheological effect was related to the pore volume and specific surface area of BaTiO₃. Due to the distinct advantage of sol–gel method for preparing nanoporous BaTiO₃ without contamination of the materials, the markedly low current destiny of the ERFs was obtained. The yield stress of ERFs with large specific surface area of BaTiO₃ reached the maximum of 3 kPa, which is higher than that of ERFs using traditional pure BaTiO₃ crystallites (lower than 1 kPa).     

Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-based pigments synthesized by a new proteic sol–gel method

Alumina-based pigments were synthesized by the proteic sol–gel method. In this method, coconut water is employed as polymeric agent instead of the conventional alkoxide precursors. To this study, three common chromophore metallic ions (Mn³⁺, Co³⁺, and Cr³⁺) were chosen in order to verify the method efficiency. Differential thermal analysis (DTA), thermogravimetry (TG), and XRD techniques were used to characterize the synthesis process. The colorimetric characterization of the produced pigments was done according to the CIE-L*a*b* 1976 norm which is recommended by the CIE (International Commission on Illumination). The synthesized pigments presented intense and uniform colors in accordance to the literature results for each chromophore ion. The produced pigments also presented agglomerated with an average grain size of 180 nm when calcined at 800 °C.     

Thermal behavior of Co<Subscript>x</Subscript>Fe<Subscript>3−x</Subscript>O<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> nanocomposites obtained by a modified sol–gel method

The thermal behavior of Co_xFe_3?xO₄/SiO₂ nanocomposites obtained by direct synthesis starting from nonahydrate ferric nitrate and hexahydrate cobalt nitrate in different ratios with and without the addition of 1,4-butanediol was studied. For the synthesis of Co_xFe_3?xO₄ (x = 0.5–2.5) dispersed in the silica matrix a wide Co/Fe molar ratio was used. The decomposition processes, formation of crystalline phases, gases evolvement and mass changes during gels annealing at different temperatures were assessed by thermal analysis. The absence of succinate precursor and a low mass loss were observed in the case of the gel obtained in the absence of 1,4-butanediol. In case of gels obtained using a stoichiometric ratio of Co/Fe, no clear delimitation between Co and Fe succinates was observed, while for samples with a Fe or Co excess, the formation of the two succinates was observed. The evolution of the crystalline phase after annealing (673, 973 and 1273 K) investigated by X-ray diffraction analysis and Fourier transformed infrared spectrometry revealed that in samples with Fe excess, stoichiometric Fe/Co ratio or low Co excess, the cobalt ferrite (CoFe₂O₄) was obtained as a single phase, while in samples with higher cobalt excess, olivine (Co₂SiO₄) as a main phase, cobalt oxide and CoFe₂O₄ as secondary phases were obtained after annealing at 1273 K. The SEM images confirmed the nanoparticles embedding in the silica matrix, while the TEM and X-ray diffraction data showed that the obtained nanoparticles’ size was below 10 nm in most samples.     

Synthesis of CaSnO<Subscript>3</Subscript> nanofibers by electrospinning combined with sol–gel

Calcium stannate (CaSnO₃) nanofibers were synthesized by electrospinning technique combined with a sol–gel process. The structure and morphology of the as-prepared CaSnO₃ nanofibers were characterized by X-ray diffraction and scanning electron microscopy, respectively. The samples had a band gap of about 3.87 eV, which was estimated by UV–Vis diffuse reflectance spectroscopy. On the basis of the experiment results, the composite fibers containing polymer and inorganic salt can be changed to pure CaSnO₃ nanofibers only when they were sintered at an appropriate temperature. At the same time, a possible mechanism of the nanofibers forming process was also proposed.     

Synthesis and characterization of Fe doped mesoporous Al<Subscript>2</Subscript>O<Subscript>3</Subscript> by sol–gel method and its use in trichloroethylene combustion

Two mesoporous alumina samples were synthesized using the sol–gel method, and these samples were tested as catalysts in trichloroethylene combustion reaction. One alumina sample was doped with Fe to study the influence of a small amount of this agent on the characteristics and properties of alumina as a catalyst. Both catalysts (pure alumina and alumina doped with Fe) were thoroughly characterized by different techniques, such as DTA/TGA, FT-IR, XRD, SEM and TEM, and the porous characterization was conducted using a N₂ physisorption technique. The doping agent presented a particular influence on the morphology and textural porosity in the alumina catalyst and therefore, it exhibited different catalytic behavior than the pure alumina catalyst. For both catalysts, the crystalline phase of γ-alumina was reported using XRD technique, and the crystallite size ranged from 7.8 to 12.8 nm. Using TEM images, the alumina catalyst doped with Fe revealed to contain a mixture of three types of iron oxide (maghemite, magnetite and hematite), mainly as roughly spherical nanoparticles. For both alumina catalysts, trichloroethylene catalytic combustion was conducted on a packed bed reactor in air at a temperature range of 50 to 600 °C. The alumina catalyst doped with Fe showed a higher catalytic activity than pure alumina, mainly due to the presence of micropores and grain morphology of flat faces.     

Synthesis of MgNb<Subscript>2</Subscript>O<Subscript>6</Subscript> nanocrystalline powders by an improved citrate sol–gel technique

MgNb₂O₆ nanocrystalline powders have been synthesized at a low temperature by improved citrate sol–gel method in this paper. The high quality solution of Nb⁵⁺ was prepared using Nb₂O₅ as the starting material. The crystal structure and microstructure of MgNb₂O₆ powders were characterized by XRD and SEM techniques, and the effects of preparation craft including pH value and the proportion of citric acid to the niobium ions on the crystal structure and microstructure of powders were also investigated. XRD and TG/DTA results show that the single phase of MgNb₂O₆ for synthesized powders can be obtained by calcining the precursor at 700 °C. SEM results indicate that the average particle size of MgNb₂O₆ exhibits a significantly dependence on the pH values and the proportion of citric acid to the niobium ions, where it was found that particle size of a 20 nm can be obtained for the MgNb₂O₆ powders by sol–gel process.     

Luminescent properties of Sr<Subscript>3</Subscript>Al<Subscript>2</Subscript>O<Subscript>6</Subscript>: Eu,Pr prepared by sol–gel method

A new red-emitting long afterglow Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphor was synthesized by sol–gel methods using Sr(NO₃)₂, Al(NO₃)₃·9H₂O, Eu(NO₃)₃ and Pr(NO₃)₃ as raw materials. The crystalline structure of the phosphor powders were characterized by X-ray diffraction. Luminescent properties of the phosphor powders were analyzed by the fluorescence spectrophotometer. Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphor powders with single Sr₃Al₂O₆ phase were prepared at 1200 °C for 2 h in the reducing atmosphere. Pr³⁺ doped made the light intensity and the light-lasting time of Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphors improved. The emission peaks of the Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphor powders lay at 612 nm with the excitation of 472 nm and the longest afterglow time could last for about 15 min at Pr³⁺ content of 0.06.     

Preparation and characterisation of NdAlO<Subscript>3</Subscript> nanocrystals by modified sol–gel method

Nanocrystalline single-phase neodymium monoaluminate (NdAlO₃) has been prepared from neodymium oxide and aluminium nitrate by modified Pechini’s method. Malic acid has been used for the first time as a new complexing agent in the sol–gel process. It has facilitated, without adding 1,2-ethanediol, a low-temperature synthesis at 1,050 °C compared to the temperature of 1,630 °C needed for the solid-state preparation. The characterisation of the nanoparticles has been carried out by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and infrared spectroscopy in the range 75–4,000 cm⁻¹. The smallest particles have size of 30 nm and are anisometric; agglomerates of particles have been also observed. The material has pyknometric density of 3.956 g/cm³ at T = 293.15 K and specific surface area 5.2 m²/g. The binding energies of O 1s, Al 2p, Nd 3d, and Nd 4d electrons have been found chemically shifted in NdAlO₃ compared to the values for the respective elements.     

Sol–gel synthesis of iron yttrium garnet Y<Subscript>3</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript> using metal acetylacetonates

The synthesis of hydrolytically active heteroligand complexes of the composition [M(O₂C₅H₇)x(ⁱOC₅H₁₁)_y] (M = Fe³⁺ and Y³⁺) using iron and yttrium acetylacetonates was studied. Their reactivity was shown to be dependent on the degree of shielding of iron and yttrium cations in hydrolysis and polycondensation during the formation of a connected dispersion system. The crystallization temperature of iron yttrium garnet Y₃Fe₅O₁₂ upon heating xerogel was determined. It was found that the dispersity, microstructure, and magnetic characteristics of the products depend on the synthesis conditions.     

Catalytic properties of Fe/SiO<Subscript>2</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> systems,obtained via sol–gel method

The high efficacy of iron-containing catalysts based on SiO₂–Al₂O₃ systems obtained via sol–gel method in the oxidative destruction of carmoisine azo dye in aqueous solutions is demonstrated. It is found that the stability of the catalysts with respect to the leaching of iron ions into a solution during catalysis grows along with the aluminum content in the composition of aluminosilicate supports. It is concluded that the synthesized catalysts are promising materials for purifying wastewaters contaminated with organic dyes.     

Synthesis and characterization of spinel-type CuAl<Subscript>2</Subscript>O<Subscript>4</Subscript> nanocrystalline by modified sol–gel method

Nanocrystalline Copper aluminate (CuAl₂O₄) was prepared by sol–gel technique using aluminum nitrate, copper nitrate, diethylene glycol monoethyl ether and citric acid were used as precursor materials. This method starts from of the precursor complex, and involves formation of homogeneous solid intermediates, reducing atomic diffusion processes during thermal treatment. The formation of pure crystallized CuAl₂O₄ nanocrystals occurred when the precursor was heat-treated at 600 °C in air for 2 h. The stages of the formation of CuAl₂O₄, as well as the characterization of the resulting compounds were done using thermo–gravimetric analysis, X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy. The products were analyzed by transmission electron microscopy and ultraviolet–visible (UV–Vis) spectroscopy to be round, about 17–26 nm in size and E _g = 2.10 eV.     

NiTiO<Subscript>3</Subscript> nanoparticles encapsulated with SiO<Subscript>2</Subscript> prepared by sol–gel method

NiTiO₃ (NTO) nanoparticles encapsulated with SiO₂ were prepared by the sol–gel method resulting on core-shell structure. Changes on isoelectric point as a function of silica were evaluated by means of zeta potential. The NTO nanoparticles heat treated at 600°C were characterized by X-ray diffraction, transmission electron microscopy (TEM) and energy dispersive X-ray analysis. TEM observations showed that the mean size of NTO is in the range of 2.5–42.5 nm while the thickness of SiO₂ shell attained 1.5–3.5 nm approximately.     

Preparation of nanostructured thin films of yttrium aluminum garnet (Y<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript>) by Sol—Gel technology

The synthesis of hydrolytically active heteroligand coordination compounds [M(C₅H₇O₂)_3–x(C₅H₁₁Oⁱ)_x] (where M = Al³⁺ and Y³⁺) using aluminum and yttrium acetylacetonates has been studied. The gel formation kinetics in their solutions upon hydrolysis and polycondensation has also been studied. Thin films of a solution of these precursors have been applied to polished sapphire substrates by dip coating. The crystallization of nanostructured yttrium aluminum garnet (Y₃Al₅O₁₂) films during heat treatment of xerogel coatings under various conditions has been studied. How the phase composition, microstructure, and particle size depend on the synthesis parameters has been recognized.     

Preparation of HfB<Subscript>2</Subscript>/SiC composite powders by sol–gel technology

Sol–gel technology was used to chemically modify the surface of HfB₂ powders with highly dispersed silicon carbide using two carbothermy protocols: (1) under heating to 1500°С in flowing argon (100 mL/min) without exposure and (2) under dynamic vacuum conditions (p ~ 1 × 10^–5–1 × 10^–6 MPa) at 1400°С with 4-h exposure. The phase composition and microstructural features of the thus-prepared HfB₂/xSiC (x = 10–65 vol %) composite powders were studied. The products prepared by the second protocol showed an enhanced oxidation resistance in the range 20–1400°C in flowing air compared to individual HfB₂.     

Rapid synthesis of the low thermal expansion phase of Al<Subscript>2</Subscript>Mo<Subscript>3</Subscript>O<Subscript>12</Subscript> via a sol–gel method using polyvinyl alcohol

Aluminum molybdate was successfully synthesized using a simplified PVA assisted sol–gel method resulting in highly crystalline, monophasic (monoclinic P2₁/a) samples. These materials could readily be obtained at temperatures of 600 and 700 °C after calcining for as little as 15–20 min. Scanning electron microscopy and X-ray powder diffraction indicated that even the sample calcined at 600 °C for 20 min was free of impurities and composed of submicron sized particles (~300 nm). Transmission electron microscopy was used to confirm the monophasic character and submicron dimensions of the as-prepared powders. In addition to producing high quality samples, it was also observed that the metal to PVA ratio used during this simplified synthesis, could be used as a control parameter for tailoring the particle sizes of the final product.     

Modeling and optimization of densification of nanocrystalline Al<Subscript>2</Subscript>O<Subscript>3</Subscript> powder prepared by a sol–gel method using response surface methodology

Response surface methodology (RSM) based on central composite design (CCD) was successfully applied to the optimization and modeling of densification of nanocrystalline Al₂O₃ powder prepared by sol–gel method. The effects of three operating variables, sintering temperature, calcination temperature and milling time on the densification of nanocrystalline Al₂O₃ were systematically evaluated. A quadratic model for densification was proposed. Analysis of variance (ANOVA) indicated that the proposed quadratic model could be used to navigate the design space. The simulated values obtained from the statistical model were in conformity with the experimental results within an average error of ±1.5%. The optimum operating conditions for densification were found to be 1,579 °C of sintering temperature, 909 °C of calcination temperature and 117 min of milling time. The obtained density under the optimum conditions determined by RSM was 98.5%. The results confirmed that RSM based on central composite design was an accurate and reliable method to optimize the densification conditions of nanocrystalline Al₂O₃ powder.     

Preparation of LiTaO<Subscript>3</Subscript> nanoparticles by a sol–gel route

A sol–gel route was developed to prepare pure ultrafine LiTaO₃ powders using Ta₂O₅, Li₂CO₃, citric acid (CA) as chelating agent, ethylene glycol (EG) as esterification agent and polyethylene glycol (PEG) as dispersant. The effects of pH value and heat treatment temperature of powder precursor on the synthesis of LiTaO₃ powders were investigated. The phase content and morphology of the final product were evaluated by XRD, SEM and TEM. A transparent gel was produced when heating a mixed-solution of CA, EG, Li and Ta ions with a molar ratio of [CA]:[EG]:[Li]:[Ta] = 3.0:6.0:1.0:1.0 and 2‰ PEG additions with a pH value of 7 at water bath temperature of 80 °C. The results showed that single phase LiTaO₃ powders with average particle sizes of nanometers were produced after heat treatment of the powder precursor at 650, 700, 800, and 900 °C respectively for 2 h.