网络间含离子键的聚氨酯/接枝乙烯基酯树脂互穿聚合物网络 研究

分别以双酚-A型环氧树脂E-51和聚醚型环氧树脂E-46为原料合成了两种二乙胺-环氧树脂和加成多元醇(分别命名为AE-51,AE-46),将其和甲基丙烯酸一起用于合成聚氨酯/接枝乙烯基酯树脂(PU/接枝VER)互穿聚合物网络(IPN),使之在两个网络间形成离子键。实验结果表明,这类新型的IPN材料中两个网络间的互穿程度与相容性进一步提高,从而导致刚性的接枝VER对弹性的PU网络有更好的增强效果。DSC和FTIR的测定结果表明,在含AE-51的IPN中,由于离子键的作用使PU网络硬段的有序结构遭到很大程度的破坏,与AE-51和PU网络中的硬段以及VER网络有较好的相容性有关,因此这类IPN材料具有较好的力学性能。     

室温固化蓖麻油聚氨酯/乙烯基聚合物互穿网络材料的一些规律及其性能

研究了蓖麻油与甲苯二异氰酸酯及丙烯酸酯或苯乙烯等乙烯基单体在室温下生成的互穿网络聚合物(IPN)的一些规律及其性能.用红外光谱追踪表明,聚氨酯的生成快于甲基丙烯酸甲酯的聚合.研究IPN凝胶点指出.凝胶点时间随聚氨酯含量增加及聚苯乙烯含量减少而缩短.丙烯酸甲酯在生成IPN过程中凝胶的生成速度要比苯乙烯的场合快.丙烯酸丁酯、丙烯腈或丙烯酸甲酯与蓖麻油聚氨酯生成的IPN的抗张强度在聚氨酯占一半时呈现最大值.透射电镜观察表明,生成速率较快的聚氨酯的微区存在于聚丙烯酸甲酯中.聚丙烯酸甲酯与蓖麻油聚氨酯形成的IPN在tanδ-T,曲线上呈现一个宽的玻璃化转变温度.     

网间交联型增韧环氧树脂/蓖麻油聚氨酯互穿网络聚合物的动态力学性能和形态结构

以增韧环氧树脂(TEP)和蓖麻油聚氨酯[PU(CO)]形成的互穿网络聚合物(IPN),两网络间具有一定数量的交联点,在一定组成下,该IPN的tanδ-T曲线半峰宽达100℃,tanδ最大值接近1,阻尼性能良好。形态研究表明,该IPN既有增韧环氧树脂本身的两相结构,又有IPN的两相结构。     

网间交联型增韧环氧树脂/蓖麻油聚氨酯互穿网络聚合物的动态力学性能和形态结构

 以增韧环氧树脂(TEP)和蓖麻油聚氨酯[PU(CO)]形成的互穿网络聚合物(IPN),两网络间具有一定数量的交联点,在一定组成下,该IPN的tanδ-T曲线半峰宽达100℃,tanδ最大值接近1,阻尼性能良好。形态研究表明,该IPN既有增韧环氧树脂本身的两相结构,又有IPN的两相结构。     

离子-电子导电中呈现协同效应的互穿网络聚合物

用2,4-甲苯二异氰酸酯将蓖麻油及聚乙二醇(PEG)偶联成聚氨酯,同时通过自由基聚合使2-乙烯基吡啶(VP)与蓖麻油的双键共聚,生成互穿网络聚合物(IPN),其产率及凝胶含量大多超过93%,力学性能很好.当IPN与LiClO₄络合后呈现离子导电现象;与TCNE或TCNQ络合后产生电子导电,与LiClO₄及TCNE(TCNQ)络合后,呈现比上述两种导电率更大且具有协同效应的混合导电率,在25℃混合电导率可达到10^-3～10^-2S/cm.     

蓖麻油聚氨酯和乙烯类聚合物互穿网络材料的生成特点及其动态力学性能

研究蓖麻油聚氨酯/取代乙烯共聚物的互穿网络物(IPN)的生成特点指出,其中取代乙烯游离基共聚的氧化还原引发剂组份-过氧化苯甲酰或二甲基苯胺都能加速聚氨酯网络(Pu)的生成。反应温度在 30℃以上蓖麻油也能参与游离基共聚。蓖麻油不仅与TDI反应生成Pu网络,而且也有小部分参与取代乙烯共聚物长枝链的形成。Pu网络的形成较长枝链的生成为快。生成Pu网络时所放出的热促进取代乙烯与少量蓖麻油的双键共聚,最后生成的IPN不溶于甲苯。这表明生成的是接技的半IPN,而不是单纯的半IPN。动态力学研究指出,包含聚苯乙烯或聚甲基丙烯酸甲酯的这种IPN呈现二个T_g,而只包含聚丙烯腈的仅一个T_g,说明后一IPN中相容性较好,有较多的分子混合。随着聚氨酯与聚取代乙烯的比例减少,二个T_g间的差距减少,而较高温度的T_g随取代乙烯共聚物中丙烯腈含量增加而变小。     

离子键交联聚两性电解质凝胶在电场作用下的溶蚀现象

以丙烯酸(AA)和甲基丙烯酸二乙氨基乙酯(DEAM)形成的离子复合物和丙烯酰胺(AAm)为单体,采用自由基聚合制备了一系列新型的离子键交联聚两性电解质凝胶(PADA凝胶).非接触直流电场的实验表明,该离子键交联的PADA凝胶在电场下发生溶蚀现象,该现象鲜见文献报道.PADA凝胶的溶蚀速率与电场强度、溶液浓度、pH值、酸碱基团摩尔比、溶液离子价态等诸多因素有关,如溶蚀随电压的升高而增大,随盐溶液浓度的加大而增大.其溶蚀动力学研究表明PADA凝胶的溶蚀度随时间线性的增加,即溶蚀速率在整个实验时间内基本保持恒定.     

聚氨酯聚二甲基硅氧烷半IPN透气性研究

近年来,互穿聚合物网络(IPN)的开发受到了广泛的关注。以聚氨酯为一组分,聚丙烯腈、聚酯及环氧树脂等为另一组分的IPN体系的研究已有报道,而聚氨酯与有机硅的IPN体系的研究报道很少。在本文中,我们对聚氨酯(PU)与聚二甲基硅氧烷(PDMS)半IPN的透气性与结构的关系进行了研究。     

两组份互穿网络聚合物的合成研究

以蓖麻油聚氨酯和聚醚聚氨酯的不同重量比与光敏剂、催化剂、稀释剂、促进剂所组成的多相体系为反应物,分别在紫外光照射和加热的条件下合成网络Ⅰ和网络Ⅱ的互穿网络聚合物(IPN)。改变网络Ⅱ聚醚聚氨酯中各组份的摩尔比制得系列样品。红外光谱,应力-应变曲线和动态力学性能测定发现,样品的力学性能与两组份重量比和网络Ⅱ中不同组成都存在着一定关系。这些结果,为该体系IPN的合成和应用提供了一定依据。     

聚氨酯/环氧树脂互穿网络硬质泡沫塑料反应过程和微观结构

聚氨酯／环氧树脂互穿网络(PU／EPIPN)硬泡中异氰酸根的消耗速度较纯PU硬泡高，是由于环氧树脂的固化荆同时也是异氰酸根反应的催化荆。而PU／EP IPN硬泡中环氧基的反应速度和反应程度均较纯EP网络低，归因于互穿网络对基团扩散的阻碍。在互穿网络硬泡形成过程中，存在环氧开环中所新产生的羟基与异氰酸根的反应、大分子多元醇中羟基与环氧基的反应以及异氰酸根与环氧基形成嗯唑烷酮的反应三种形成网络间的化学键的途径。同时由于PU／EPIPN硬泡高度的交联，使得IPN硬泡中两个网络具有良好的相容性。动态力学性能表明所有IPN样品都只有一个玻璃化温度。透射电镜表明IPN样品无明显的相界面。     

Characterization and degradation of poly(methylphenylsiloxane)–poly(methyl methacrylate) interpenetrating polymer networks

Poly(methylphenylsiloxane)–poly(methyl methacrylate) interpenetrating polymer networks (PMPS–PMMA IPNs) were prepared by in situ sequential condensation of poly(methylphenylsiloxane) with tetramethyl orthosilicate and polymerization of methyl methacrylate. PMPS–PMMA IPNs were characterized by infrared (IR), differential scanning calorimetry (DSC), and ²⁹Si and ¹³C nuclear magnetic resonance (NMR). The mobility of PMPS segments in IPNs, investigated by proton spin–spin relaxation T₂ measurements, is seriously restricted. The PMPS networks have influence on the average activation energy E_a,av of MMA segments in thermal degradation at initial conversion. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1717–1724, 1999     

Poly(ethylene oxide)/poly(methyl methacrylate) (semi-)interpenetrating polymer networks: Synthesis and phase diagrams

Interpenetrating polymer networks (IPNs) of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) were prepared by simultaneous network formation. The PEO network was produced by acid-catlayzed self-condensation of α,ω-bis(triethoxysilane)-terminated PEO in the presence of small amounts of water. The PMMA network was formed by free radical polymerization of MAA in the presence of divinylbenzene as crosslinker. The reaction conditions were adjusted to obtain similar crosslinking kinetics for both reactions. An attempt was made to construct a phase diagram of the IPNs by measuring the composition of the IPNs at the moment of the appearance of the phase separation, as indicated by the onset of turbidity. This composition could be determined because the siloxane crosslinks of the PEO network could be hydrolyzed in aqueous NaOH with the formation of linear, soluble PEO chains. The phase diagram was compared with phase diagrams of blends of linear polymers and of semi-IPNs (crosslinked PMMA and linear PEO), obtained under similar conditions, i.e. polymerization of MMA in the presence of varying amounts of PEO. It was observed that the form of the phase diagrams of the linear polymers is similar to that of the IPNs, but is quite different from that of the semi-IPNs. Thus, homogeneous transparent materials containing up to 60% of PEO could be prepared in the blends and the IPNs, but in the semi-IPNs, phase separation occurred with PEO contents as low as 10%.     

Interpenetrating polymer network from castor oil-based polyurethanes and poly(methyl methacrylate). XV

The polyurethanes have been prepared from 2.12 functional ? OH containing castor oil and diphenyl methane diisocyanate under identical experimental conditions with a varying NCO/OH ratio. These polyurethanes were swollen in methyl methacrylate and subsequently interpenetrated by free radical polymerization using benzoyl peroxide and crosslinker ethylene glycol dimethacrylate. A series of interpenetrating polymer network (IPN) PU/PMMA IPNs were obtained as films by a transfer moulding technique. These IPNs were characterized by their resistance to chemical reagents, thermal behavior, and mechanical properties. The morphology was shown by SEM and dielectric properties at different temperatures were measured.     

Preparation and characterization of poly(N-isopropylacrylamide)-modified poly(2-hydroxyethyl acrylate) hydrogels by interpenetrating polymer networks for sustained drug release

In order to investigate the influence of hydrophobic moieties formed by poly(N-isopropylacrylamide) (PNIPAm) in a hydrogel matrix on the release behavior of the hydrogel, a series of poly(N-isopropylacrylamide) (PNIPAm)-modified poly(2-hydroxyethyl acrylate-co-2-hydroxyethyl 2-hydroxyethyl methacrylate) (P(HEA-co-HEMA)) via interpenetrating polymer networks (IPNs) were prepared by a sequential UV solution polymerization. Interestingly, it was found that P(HEA-co-HEMA)/PNIPAm IPN indicated a single glass transition temperature (T(g)) and the T(g)s of the IPNs increased with an increase in the PNIPAm component. This phenomenon may be attributed to hydrogen bonding between the two polymer networks, but the hydrogen bonding exerts less influence on the swelling behavior of the IPNs, due to the fact that IPNs can respond to changes in temperature like PNIPAm. Using 2-[(diphenylmethyl)sulphiny]acetamide (modafinil, MOD) and p-hydroxybenzoic acid (HBA) as model drug compounds, the release behavior of the IPNs was studied at body temperature, and it was found that the presence of PNIPAm could retard drug release regardless of the solubility of the drugs. Release profiles of HBA from the IPNs and their component samples as a function of time at 37 degrees C.     

Vibration damping materials based on interpenetrating polymer networks of carboxylated nitrile rubber and poly(methyl methacrylate)

Interpenetrating polymer networks (IPNs) based on carboxylated nitrile rubber (XNBR) and poly(methyl methacrylate)s were synthesized. Crosslinked XNBR was swollen in methyl methacrylate containing benzoyl peroxide as initiator and tetraethylene glycol dimethacrylate as crosslinking agent. The compositions of the IPNs were varied by changing the swelling time of the rubber in the methacrylate monomer. The dynamic mechanical properties of the IPNs were studied. The dynamic mechanical properties in the range 1–10⁵ Hz were obtained by the time‐temperature superposition of the data under multifrequency mode, which indicated high tan δ with good storage modulus in the entire frequency range. This indicates the suitability of these IPNs as vibration and acoustic dampers. Copyright © 2002 John Wiley & Sons, Ltd.     

The Effect of Synthesis Method on Three-component IPNs Morphology and Property

Three-component IPNs were synthesized from polyurethane/poly (methyl acrylate aminoethyl methacrylate)/epoxy resin [PU/P(MADMA)/EP] by simultaneous synthesis interpenetrating polymer networks method(SINs) and sequential synthesis interpenetrating polymer networks method (STPNs). Comparing the effect of the two synthesis methods on the morphology and mechanical properties of three-component IPNs, it was found that the compatibility of three-component IPNs depends on the component ratios and interpenetrating formation , the different synthesis methods make the entanglement and interpenetrating between networks changed. The tensile strength of SIPNs is bigger than that of SINs, while the elongation at break of SINs is bigger than that of SIPNs. It is feasible to use stepwise staining method to observe the morphology change.     

Synthesis and characterization of polyaniline filled PU/PMMA interpenetrating polymer networks

A series of conducting interpenetrating polymer networks (IPNs), are prepared by sequential polymerization of castor oil based polyurethane (PU) with poly(methyl methacrylate) (PMMA) and polyaniline doped with camphor sulphonic acid (PAni)_CSA. The effect of different amount of PAni (varies from 2.5-12.5%) on the properties of PU/PMMA (50/50) IPNs such as electrical properties like conductivity, dielectric constant and dissipation factor; mechanical properties like tensile strength and percentage elongation at break have been reported. (PAni)_CSA filled IPNs shows improved tensile strength than the unfilled IPN system. The thermal stability and surface morphology of unfilled and (PAni)_CSA filled PU/PMMA (50/50) IPN sheets were investigated using a thermogravimetric analyzer (TGA) and a scanning electron microscope (SEM). TGA thermograms of (PAni)_CSA filled PU/PMMA (50/50) IPNs show a three-step thermal degradation process. SEM micrograms of filled PU/PMMA IPN system shows spherulitic structure at higher concentration of (PAni)_CSA.     

Gas barrier and adhesion of interpenetrating polymer networks based on poly(diurethane bismethacrylate) and different epoxy-amine networks

Interpenetrating polymer networks (IPNs) composed of poly(methacrylate) and epoxy-amine networks made in situ between two oriented polypropylene sheets were examined in terms of their oxygen barrier and adhesion to the substrate properties. A particular attention was devoted to a system presenting an obvious phase separation. Kinetics of network formation and phase behavior were investigated by infrared and UV-visible spectroscopy, respectively. Since the poly(methacrylate) network could be instantaneously generated by photoirradiation, IPNs differing in network sequence formation were prepared. The influence of the moment at which irradiation was induced, on gas barrier properties of different films was examined. It was shown that similar oxygen transmission rates are obtained whatever the moment of irradiation.     

Structure-property relationships in a reactively coupled ductile matrix/brittle dispersed phase blend

Blends of t-butylaminoethyl methacrylate grafted polyethylene (PE-g-tBAEMA) with methyl methacrylate-methacrylic acid copolymer (PMMA-MAA) and polymethyl methacrylate (PMMA) were prepared in a Banbury type batch mixer. The effects of component proportions and processing conditions on the melt flow index, morphology, impact, and tensile properties of the resulting polymer blends were investigated. The interfacial chemical reaction was studied using Fourier transform infrared (FTIR) technique. It was observed that the melt index of the blends was reduced with increasing melt processing temperature and mixing time, indicating the formation of PE-g-PMMA block copolymer. New IR bands at 1554, 1628, 1800, and 1019 cm^?1 were observed only for PE-g-tBAEMA/PMMA-MAA, the reactive blends, but not for PE-g-tBAEMA/PMMA, the nonreactive blend. These IR bands were attributed to the amide, carboxylate anion and methacrylimide formation resulting from the chemical reaction between the secondary amine on the PE-g-tBAEMA/PMMA moiety and the carboxylic acid on PMMA-MAA segment. The morphology of the blends in various compositions was examined using scanning electron microscopy (SEM) and related to their mechanical properties. All of the blends have a domain structure whose morphology is strongly dependent on the concentration of the dispersed phase. Furthermore, the PE-g-tBAEMA/PMMA-MAA reactive blends were shown to have much finer morphology than the corresponding nonreactive blends. For the reactive polymer blends consisting of brittle particles dispersed in the ductile matrices, the PE-g-tBAEMA/PMMA-MAA, impact and tensile result higher than predicted by the additivity rule were observed. The toughening of polyethylene by PMMA was explained by a “cold-drawing” mechanism. The Young's modulus of the blends and the extent of interfacial adhesion were analyzed with Takayanagi and Sato-Furukawa's theories. © 1993 John Wiley & Sons, Inc.     

The role of tin(II) octoate – azobisisobutyronitrile complex in the formation rate of the respective networks in simultaneous interpenetrating polymer networks

Simultaneous interpenetrating polymer networks (IPNs) based on polyether polyurethane (PUR) and poly(methyl methacrylate‐co‐trimethylol‐propane trimethacrylate) (PMMA) were prepared in bulk at 60°C, using tin(II) octoate and azobisisobutyronitrile (AIBN) as pur polymerization catalyst and free‐radical initiator, respectively. The kinetics of the PUR network formation, PMMA network formation as well as PUR/PMMA IPN formation were studied independently by Fourier transform infra‐red spectroscopy. The simultaneous formation of the two networks interfered with each other, although they follow different polymerization mechanisms. Mainly two effects concerning the free‐radical polymerization have been seen: a decrease of the initiation period and an earlier appearance of the Trommsdorff effect when increasing the concentration of the catalyst. On the other hand, the presence of AIBN in the reaction medium drastically reduced the catalytic efficiency of the organotin compound. An explanation of these results for this particular activating system could be the formation of a cyclic equimolar complex by coordination of the nitrile groups of AIBN with the Sn(II) atom. Complexation both reduces the effective catalyst concentration and induces steric constraints in the azo bond of AIBN, rendering this linkage weaker and more easily cleavable and allowing an early decomposition into radicals of the complexed AIBN. The maximum rate corresponds to a 1:1 complex. Further, decomposition into radicals leads to tin oxidation and formation of a new tetravalent organotin compound, the catalytic activity of which is lower than that of pure tin(II) octoate for the isocyanate‐alcohol reaction.