We have developed and validated a high-performance liquid chromatography-tandem mass spectrometric (LC-MS/MS) method for determining urine caffeine and 14 caffeine metabolites suitable for estimating caffeine exposure and metabolic phenotyping in population studies. Sample preparation consisted solely of a series of simple reagent treatments at room temperature. Stable isotope-labeled analogs were used as internal standards for all analytes. We developed rapid LC-MS/MS separations for both positive and negative ion mode electrospray ionizations to maximize measurement sensitivity. Limits of detection were 0.05–0.1 μmol/L depending on the analytes. Method imprecision, based on total coefficients of variation, was generally <7 % when analyte concentration was >1 μmol/L. Analyte recoveries were typically within 10 % of being quantitative (100 %), and good agreement was observed among analytes measured across different MS/MS transitions. We applied this method to the analysis of a convenience set of human urine samples (n?=?115) and were able to detect a majority of the analytes in ≥99 % of samples as well as calculate caffeine metabolite phenotyping ratios for cytochrome P450 1A2 and N-acetyltransferase 2. Whereas existing LC-MS/MS methods are limited in number of caffeine metabolites for which they are validated, or are designed for studies in which purposely elevated caffeine levels are expected, our method is the first of its kind designed specifically for the rapid, sensitive, accurate, and precise measurement of urine caffeine and caffeine metabolites at concentrations relevant to population studies.
Figure The determination of caffeine and its metabolites by LC-MS/MS. Both positive and negative ion mode electrospray ionization were used to maximize measurement sensitivity and selectivity, allowing the development of a robust method suitable for estimating caffeine exposure and metabolic phenotyping in population studies
A new sample-treatment procedure has been developed for determination of total linear alkylbenzene sulfonate (LAS), i.e. homologues and isomers, in agricultural soil. The procedure involves two steps, ultrasound-assisted extraction of LAS from the samples with methanol then clean-up of the methanolic extracts and preconcentration of the LAS by solid-phase extraction on two adsorbent cartridges (SAX and C18). The ultrasound-assisted procedure reduces extraction time (10 min in contrast with 6–12 h for conventional Soxhlet extraction) and requires only small volumes of organic solvent. The effect of different variables interacting in the ultrasound-assisted extraction process was studied. Finally, separation and quantification of the homologues and isomers of LAS was performed by liquid chromatography with fluorescence detection (LC?FD). 2-Octylbenzenesulfonic acid sodium salt (Na-2ØC8-LAS) was used as internal standard. The proposed method was satisfactorily used for determination of LAS in agricultural soil samples from the fertile plain of Granada (Spain).
This paper describes the development of a biosensor for the detection of anti-hemagglutinin antibodies against the influenza virus hemagglutinin. The steps of biosensor fabrications are as follows: (i) creation of a mixed layer containing the thiol derivative of dipyrromethene and 4-mercapto-1-butanol, (ii) complexation of Cu(II) ions, (iii) oriented immobilization of the recombinant histidine-tagged hemagglutinin, and (iv) filling free spaces with bovine serum albumin. The interactions between recombinants hemagglutinin from the highly pathogenic avian influenza virus type H5N1 and anti-hemagglutinin H5 monoclonal antibodies were explored with Osteryoung square-wave voltammetry. The biosensor displayed a good detection limit of 2.4 pg/mL, quantification limit of 7.2 pg/mL, and dynamic range from 4.0 to 100.0 pg/mL in buffer. In addition, this analytical device was applied for the detection of antibodies in hen sera from individuals vaccinated and non-vaccinated against the avian influenza virus type H5N1. The limit of detection for the assay was the dilution of sera 1: 7?×?106, which is about 200 times better than the enzyme-linked immunosorbent assay.
The food-related isothiocyanate sulforaphane (SFN), a hydrolysis product of the secondary plant metabolite glucoraphanin, has been revealed to have cancer-preventive activity in experimental animals. However, these studies have often provided inconsistent results with regard to bioavailability, bioaccessibility, and outcome. This might be because the endogenous biotransformation of SFN metabolites to the structurally related erucin (ERN) metabolites has often not been taken into account. In this work, a fully validated liquid chromatography tandem mass spectrometry (LC–MS–MS) method was developed for the simultaneous determination of SFN and ERN metabolites in a variety of biological matrices. To reveal the importance of the biotransformation pathway, matrices including plasma, urine, liver, and kidney samples from mice and cell lysates derived from colon-cancer cell lines were included in this study. The LC–MS–MS method provides limits of detection from 1 nmol L?1 to 25 nmol L?1 and a mean recovery of 99 %. The intra and interday imprecision values are in the range 1–10 % and 2–13 %, respectively. Using LC–MS–MS, SFN and ERN metabolites were quantified in different matrices. The assay was successfully used to determine the biotransformation in all biological samples mentioned above. For a comprehensive analysis and evaluation of the potential health effects of SFN, it is necessary to consider all metabolites, including those formed by biotransformation of SFN to ERN and vice versa. Therefore, a sensitive and robust LC–MS–MS method was validated for the simultaneous quantification of mercapturic-acid-pathway metabolites of SFN and ERN.
A simple, low-cost, and efficient online focusing method that combines a dynamic pH junction and sweeping by capillary electrophoresis with polymer solutions was developed and optimized for the simultaneous determination of benzoic acid (BA) and sorbic acid (SA). A sample solution consisting of 2.5 mM phosphate at pH 3.0 and a buffer solution containing 15 mM tetraborate (pH 9.2), 40 mM sodium dodecyl sulfate, and 0.100 % (w/v) poly(ethylene oxide) were utilized to realize dynamic pH junction–sweeping for BA and SA. Under the optimized conditions, the entire analysis process was completed in 7 min, and a 900-fold sensitivity enhancement was achieved with limits of detection (S/N?=?3) as low as 8.2 and 6.1 nM for BA and SA, respectively. The linear ranges were between 20 nM and 20 μM for BA and 20 nM and 10 μM for SA, with correlation coefficients greater than 0.992. The recoveries of the proposed method ranged from 90 to 113 %. These satisfactory results indicate that this method has the potential to be an effective analytical tool for the rapid screening of BA and SA in different food products.
Figure An online focusing strategy combining dynamic pH junction and sweeping for sensitive determination of benzoic and sorbic acid in food products using capillary electrophoresis wit polymer solutions
Breath has been investigated as an alternative matrix for detecting recent cocaine intake; however, there are no controlled cocaine administration studies that investigated the drug’s disposition into breath. Breath was collected from 10 healthy adult cocaine users by asking them to breathe into a SensAbues device for 3 min before and up to 22 h following 25 mg intravenous (IV) cocaine dosing on days 1, 5, and 10, and assayed with a validated liquid chromatography-high-resolution mass spectrometry (LC-HRMS) method to quantify breath cocaine, benzoylecgonine (BE), ecgonine methyl ester (EME), and norcocaine. The assay was linear from 25 to 1,000 pg/filter, extraction efficiencies were 83.6–126 %, intra- and inter-assay imprecision was <10.6 %, and bias was between ?8.5 and 16.8 %. No endogenous or exogenous interferences were observed for more than 75 tested. Analytes were generally stable under short-term storage conditions. Ion suppression was less than 46 %. Of breath specimens collected after controlled cocaine administration, 2.6 % were positive for cocaine (26.1–66 pg/filter, 1–9.5 h), 0.72 % BE (83.3–151 pg/filter, 6.5–12.5 h), and 0.72 % EME (50–69.1 pg/filter, 6.5–12.5 h); norcocaine was not detected. Methanolic extraction of the devices themselves, after filters were removed, yielded 19.2 % positive cocaine tests (25.2–36.4 pg/device, 10 min–22 h) and 4.3 % positive BE tests (26.4–93.7 pg/device, 10 min–22 h), explaining differences between the two extraction techniques. These results suggest that the device reflects the drug in oral fluid as well as lung microparticles, while the filter reflects only drug-laden microparticles. A sensitive and specific method for cocaine, BE, EME, and norcocaine quantification in breath was developed and validated. Cocaine in breath identifies recent cocaine ingestion, but its absence does not preclude recent use.
Nucleotides, their analogues, and other phosphate esters and phosphoramidates often contain the triethylammonium cation as a counterion. We found that this may be lost during chromatographic purification or concentration of solutions, yielding products in acidic forms or containing sub-stoichiometric amounts of the counterion. This in turn may be detrimental, e.g., due to possible decomposition of a compound or inaccurate sample preparation. Correlations between the structure of studied compounds and their susceptibility for cation loss were analyzed. Modifications in preparative techniques were developed to obtain the studied compounds with stoichiometric anion to cation ratios.
Graphical Abstract Triethylammonium salts of phosphate esters and phosphoramidates may lose the cationic component during chromatography or evaporation of solvent
Bisphenol A (BPA) is a synthetic chemical extensively used in many consumer products. It mimics estrogen activities and is related to developmental disorders and metabolic diseases. The current challenge of BPA detection is their low circulating levels at 0.1～10 ng/mL which is close to the detection limit of most of current analytical methods. In this report, we developed a simple, sensitive, and accurate liquid chromatography mass spectrometry (LCMS) method after 1-methylimidazole-2-sulfonyl chloride derivatization. The method significantly improves sensitivity 5～9-fold over dansyl derivatization and approximately 100-fold without derivatization.
Three-dimensional structures comprising polypyrrole nanowires (PPyNWs) and molecularly imprinted polymer (MIP) were prepared by electropolymerization on the surfaces of a glassy carbon electrode (GCE). The modified GCE possesses both large surface area and good electrocatalytic activity for oxidizing dopamine (DA), and this leads to high sensitivity. The electropolymerized MIP has a large number of accessible surface imprints, and this makes the GCE more selective. Under optimal conditions and at a working voltage of typically 0.23 V (vs. SCE), the calibration plot is linear in the 50 nM to 100 μM DA concentration range, and the limit of detection is 33 nM. The sensor has been successfully applied to the analysis of DA in injections.
Graphical abstract Schematic of a three-dimensional nanocomposite based dopamine sensing platform based on the use of a molecularly imprinted polymer and poly(pyrrole) nanowires. The modified polypyrrole nanowires and molecularly imprinted polymer endowed high electrocatalytic capacity and good selectivity for dopamine recognition, respectively.
A hybrid of reduced graphene oxide–palladium (RGO–Pd) nano- to submicron-scale particles was simultaneously chemically prepared using microwave irradiation. The electrochemical investigation of the resulting hybrid was achieved using cyclic voltammetry and differential pulse voltammetry. RGO–Pd had a higher current response than unmodified RGO toward the oxidation of morphine. Several factors that can affect the electrochemical response were studied, including accumulation time and potential, Pd loading, scan rate, and pH of electrolyte. At the optimum conditions, the concentration of morphine was determined using differential pulse voltammetry in a linear range from 0.34 to 12 μmol L?1 and from 14 to 100 μmol L?1, with detection limits of 12.95 nmol L?1 for the first range. The electrode had high sensitivity toward morphine oxidation in the presence of dopamine (DA) and of the interference compounds ascorbic acid (AA) and uric acid (UA). Electrochemical determination of morphine in a spiked urine sample was performed, and a low detection limit was obtained. Validation conditions including reproducibility, sensitivity, and recovery were evaluated successfully in the determination of morphine in diluted human urine.
Immunoglobulin Y (IgY) is derived from egg yolk and has been identified as a cheap and high-yield immunoreagent. The application of IgY in immunoassays for the detection of chemical contaminants in food samples has rarely been reported. In this work, we describe a rapid and sensitive fluorescence polarization immunoassay (FPIA) for valnemulin (VAL) using IgY which was produced using a previously prepared immunogen. Three fluorophore-labeled VAL tracers were synthesized and the sensitivity of the best tracer (VAL–DTAF) in the optimized FPIA with antibody IgY100 demonstrated an IC50 value of 12 ng mL?1 in buffer. After evaluation of several extraction procedures, acidified acetonitrile was selected to extract VAL from swine tissue. The recoveries of VAL in spiked swine tissue at three levels (50, 100, and 200 μg kg?1) were higher than 79 % with coefficients of variation (CVs) lower than 12 %. The limit of detection (LOD) of the FPIA in swine tissue was 26 μg kg?1 and was lower than the maximum residue limit (MRL) of VAL set by the European Union. The study showed that IgY could be a good substitute for IgG when developing a high-throughput assay for chemical residues.
It was recently reported in the murine model of metastatic breast cancer (4T1) that tumor progression and development of metastasis is associated with systemic endothelial dysfunction characterized by impaired nitric oxide (NO) production. Using Raman 3D confocal imaging with the analysis of the individual layers of the vascular wall combined with AFM endothelial surface imaging, we demonstrated that metastasis-induced systemic endothelial dysfunction resulted in distinct chemical changes in the endothelium of the aorta. These changes, manifested as a significant increase in the protein content (18 %) and a slight decrease in the lipid content (4 %), were limited to the endothelium and did not occur in the deeper layers of the vascular wall. The altered lipid to protein ratio in the endothelium, although more pronounced in the fixed vascular wall, was also observed in the freshly isolated unfixed vascular wall samples in the aqueous environment (12 and 7 % change of protein and lipid content, respectively). Our results support the finding that the metastasis induces systemic endothelial dysfunction that may contribute to cancer progression.
We describe the preparation of carbon quantum dots (C-dots) by a one-step hydrothermal method starting from o-aminophenol as the precursor. The C-dots exhibit bright both blue fluorescence (with excitation/emission peaks at 300/410 nm and with quantum yield of 0.40) and green fluorescence (420/500 nm; QY 0.28) without any other element doping. The unique emission properties are attributed to a synergistic effect of amino and hydroxy groups on the surface of the C-dots. The C-dots are shown to be viable fluorescent probes for heparin. The positively charged surface amino groups are assumed to interact with sulfate and carboxy groups in heparin via electrostatic interactions and hydrogen bonding. This causes the blue fluorescence of C-dots to be turned off (quenched). Fluorescence is strongest at a pH value of 6. The fluorometric calibration plot is linear in the 10 to 100 nM concentration range, with an 8.2 nM detection limit (at a signal-to-noise ratio of 3).
Graphical abstract Carbon quantum dots with dual fluorescence emission bands were synthesized and are shown to be a viable fluorescent probe for heparin.
This study aims at evaluating the capabilities of synchrotron radiation micro X-ray fluorescence spectrometry (SR micro-XRF) for qualitative and semi-quantitative elemental mapping of the distribution of actinides in human tissues originating from individuals with documented occupational exposure. The investigated lymph node tissues were provided by the United States Transuranium and Uranium Registries (USTUR) and were analyzed following appropriate sample pre-treatment. Semi-quantitative results were obtained via calibration by external standards and demonstrated that the uranium concentration level in the detected actinide hot spots reaches more than 100 μg/g. For the plutonium hot spots, concentration levels up to 31 μg/g were found. As illustrated by this case study on these unique samples, SR micro-XRF has a high potential for this type of elemental bio-imaging owing to its high sensitivity, high spatial resolution, and non-destructive character.
Graphical Abstract SR micro-XRF study of the distribution of actinitides in human tissues. Left Location of the U-contaminated tissue sample in the human body. Middle U distribution derived from the high resolution SR micro-XRF scan on the tissue sample, indication of five U hot spots. Right Detail of the point measurement spectrum of U hot spot 3, intense U-Lα fluorescence peak located at 13.6 keV.
This work demonstrates the feasibility of ultra-trace determination of halogens in biological samples by inductively coupled plasma mass spectrometry (ICP-MS) after decomposition by microwave-induced combustion (MIC). The conventional MIC method was improved to allow the combustion of samples with mass higher than that used in previous works in order to achieve better limits of detection (LODs). The applicability of the proposed method for ultra-trace determination of bromine and iodine in organic samples was demonstrated here using honey. It was possible to decompose up to 1000 mg of honey using microcrystalline cellulose as a combustion aid and polyethylene film for sample wrapping. After combustion, analytes were absorbed using 50 mmol L?1 NH4OH and recoveries for Br and I were between 99 and 104 %, and relative standard deviations were lower than 5 %. Microwave-assisted alkaline dissolution (MA-AD) was also evaluated for honey sample preparation using NH4OH or tetramethylammonium hydroxide solutions. However, the LODs for the MA-AD method were unsuitable because the high carbon content in digests required a dilution step prior to the analysis by ICP-MS. The LODs obtained by MIC were improved from 1143 to 34 ng g?1 for Br and from 571 to 6.0 ng g?1 for I, when compared to the MA-AD method. Furthermore, it was possible to decompose up to eight samples simultaneously in 30 min (including the cooling step) with very low reagent consumption and consequently lower generation of effluents, making MIC method well suited for routine ultra-trace determination of Br and I in honey.
High-resolution Fourier transform ion cyclotron resonance (FT-ICR) mass spectrometry imaging enables the spatial mapping and identification of biomolecules from complex surfaces. The need for long time-domain transients, and thus large raw file sizes, results in a large amount of raw data (“big data”) that must be processed efficiently and rapidly. This can be compounded by large-area imaging and/or high spatial resolution imaging. For FT-ICR, data processing and data reduction must not compromise the high mass resolution afforded by the mass spectrometer. The continuous mode “Mosaic Datacube” approach allows high mass resolution visualization (0.001 Da) of mass spectrometry imaging data, but requires additional processing as compared to feature-based processing. We describe the use of distributed computing for processing of FT-ICR MS imaging datasets with generation of continuous mode Mosaic Datacubes for high mass resolution visualization. An eight-fold improvement in processing time is demonstrated using a Dutch nationally available cloud service.
Polychlorinated biphenyls (PCBs) are a group of environmental persistent organic pollutants, which can be metabolized into a series of metabolites, including hydroxylated metabolites (OH-PCBs) in biota. Nineteen of 209 PCB congeners can form chiral stable isomers. However, atropisomeric determination of the hydroxylated metabolites of these chiral PCBs has never been reported by LC methods. In this work, a novel HPLC-MS method was developed to detect five chiral OH-PCBs (4OH-PCB91, 5OH-PCB91, 4OH-PCB95, 5OH-PCB95 and 5OH-PCB149) using HPLC-MS without a derivatization step.
Results
The influences of column-type, column temperature, flow rate and ratio of the mobile phase on the atropisomeric separation were investigated in detail. In the final method, calibration curves, based on peak areas against concentration, were linear in a range of 1–100 ng mL-1 of five chiral OH-PCBs with correlation coefficients ranging from 0.9996 to 0.9999 for all atropisomers of OH-PCBs. The relative standard deviations measured at the 10.0 ng mL-1 level for atropisomers of five chiral OH-PCBs were in the range of 0.60-7.55% (n?=?5). Calculated detection limits (S/N?=?3) of five chiral OH-PCBs were between 0.31 and 0.60 ng mL-1 for all OH-PCB atropisomers.
Conclusion
This HPLC-MS method was developed to detect chiral OH-PCBs and further successfully applied to measure OH-PCB atropisomer levels and enantiomeric fractions (EFs) in rat liver microsomal samples. The results from LC-MS method were highly consistent with those from GC-ECD method. It is the first time to report these OH-PCB atropisomers detected in microsomes by HPLC-MS. The proposed method might be applied also to detect chiral OH-PCBs in environmental samples and for metabolites of PCBs in vivo.
Cathinone is the principal psychostimulant present in the leaves of khat shrub, which are widely used in East Africa and the Arab peninsula as an amphetamine-like stimulant. Cathinone readily undergoes metabolism in vivo to form less potent cathine and norephedrine as the metabolites. However, the presence of cathine and norephedrine in biological fluids cannot be used as an indicator of cathinone administration. The metabolism of pseudoephedrine and ephedrine, commonly used in cold and allergy medications, also produces cathine and norephedrine, respectively, as the metabolites. Besides, cathine and norephedrine may also originate from the ingestion of nutritional supplemental products containing extracts of Ephedra species. In Canada, ephedrine and norephedrine are available for veterinary use, whereas cathinone is not approved for human or veterinary use. In this article, the detection of cathinone in equine after administration of norephedrine is reported. To the best of our knowledge, this is the first such report in any species where administration of norephedrine or ephedrine generates cathinone as the metabolite. This observation is quite significant, because in equine detection of cathinone in biological fluids could be due to administration of the potent stimulant cathinone or the nonpotent stimulant norephedrine. A single oral dose of 450 mg norephedrine was administered to four Standardbred mares. Plasma and urine samples were collected up to 120 h after administration. The amount of cathinone and norephedrine detected in post administration samples was quantified using a highly sensitive, specific, and validated liquid chromatography–tandem mass spectrometry method. Using these results, we constructed elimination profiles for cathinone and norephedrine in equine plasma and urine. A mechanism that generates a geminal diol as an intermediate is postulated for this in vivo conversion of norephedrine to cathinone. Cathinone was also detected in samples collected after a single intramuscular administration of 200 mg ephedrine and oral administration of 300 mg ephedrine in equine.
An immunochromatographic strip (ICS) using urchin-like gold nanoparticles (UGNs) for sensitive detection of fumonisin B1 (FB1) was developed to meet the requirement for rapidly monitoring FB1 in grain samples. The sensitivity of the ICS was 5.0 ng/mL, which represents a fourfold increase in sensitivity over conventional strip preparation using colloidal gold as the antibody-labeled probe. Analysis of FB1 in grain samples showed that data obtained from the strip tests were in a good agreement with those obtained from HPLC and enzyme-linked immunosorbent assays (ELISAs). This qualitative test did not require any specialized equipment, and the detection time was less than 5 min, which is suitable for on-site testing of FB1 in grain samples. Overall, to our knowledge, this is the first report of using a UGN as the antibody-labeled probe for sensitive detection of FB1 in grains using an ICS.
A specially designed micro-mixer made of silicon, calcium fluoride, and silicone with an optical transmission path of 8 μm has been used for mid-IR spectroscopy monitoring of mixing-induced chemical reactions in the low millisecond time regime. The basic principle of the proposed continuous-flow technique is to mix two liquids introduced in two times two alternatingly stacked layers through diffusion at the entrance of a 200 μm wide, 1 cm long micro-fluidic channel also serving as measurement area. By using this special, dedicated arrangement, diffusion lengths and hence the mixing times can be significantly shortened and the overall performance improved in comparison to previous systems and alternative methods. Measurements were carried out in transmission mode using an Fourier transform infrared (FTIR) microscope, recording spectra with spot sizes of 180?×?100 μm2 each at defined spots along this channel. Each of these spots corresponds to a specific reaction time: moving the measurement spot towards the entry yields shorter reaction times, moving it towards the channel’s end gives longer reaction times. This principle is generic in nature and provides a solution for accurate, chemically induced triggering of reactions requiring the mixing of two liquid reagents or reagent solutions. A typical experiment thus yields up to 85 time-coded data points, covering a time span from 1 to 80 ms at a total reagent consumption of only about 125 μL. Using the fast neutralization reaction of acetic acid with sodium hydroxide as a model, the time required for 90% mixing was determined to be around 4 ms. Additionally, first experiments on ubiquitin changing its secondary structure from native to “A-state” were carried out, illustrating the potential for time-resolved measurements of proteins in aqueous solutions.
