基于硅波导的喇曼光放大器

在硅波导上添加反向偏压的PIN结构,当波导产生受激喇曼散射时,可以将波导中双光子吸收(TPA)产生的光生自由载流子扫出波导,降低了波导的非线性损失,极大地提高了硅波导中泵浦光对信号光的喇曼增益。为了应用已经非常成熟的硅工艺,并且应用硅波导使器件小型化,根据法布里-帕罗(F-P)腔和行波放大器理论,在硅波导两端的解理面蒸镀增透膜,应用这种波导的喇曼效应设计了一种光放大器,即基于硅波导的喇曼光放大器。建立了计算放大器增益的方程,给出了不同波导长度和输入功率情况下的放大器增益,得出适当增加波导长度和泵浦光功率可以得到较高喇曼增益的结论。基于硅的光放大器有较高的饱和功率且没有泵浦源的限制,通过调整泵浦激光的波长可以放大不同波长的信号光。     

Ti扩散LiNbO_3光波导的喇曼散射

本文报道Ti扩散LiNbO_3光波导中四种直角配置的喇曼散射光谱。实验中,我们观测到了在这些配置下异常的喇曼光谱现象。这一现象可归结为光波导中入射光TE/TM模式的变换行为。     

硅波导受激喇曼散射放大信号光的数值模拟

提出了用连续泵浦光在硅波导中的受激喇曼散射对信号光进行放大的方法.建立了信号光和泵浦光在硅波导中传输的耦合方程,得到了计算信号光增益的理论模型.利用数值模拟结果,对泵浦功率沿波导的分布,信号光在不同波导长度以及输入功率情况下的增益等进行了分析和讨论.结果表明,适当增加波导长度和泵浦光功率可以得到较高喇曼增益的结论.     

单纵模Nd:YAG激光泵浦H2气中的受激喇曼散射

用单纵模Nd:YAG激光(波长1.06μm,脉宽9ns,线宽0.003cm-1)泵浦氢气中的受激喇曼散射,产生很强的后向一级斯托克斯.当泵浦能量为120mJ,压力为1.5MPaH2时,后向和前向喇曼的光子转化效率分别为66%和15%,而在4MPa时两个数值分别为46%和39%.由于后向喇曼与前向喇曼和泵浦光的传播方向相反,二者的相互竞争产生了张弛振荡,使得后向和前向喇曼的时间波形都分裂为两个峰,后向喇曼的两个峰都被压窄到1ns,使峰值功率达到了泵浦光功率的二倍,这在前向喇曼是不可能的.而且后向喇曼的光束质量要大大优于泵浦光和前向喇曼的光束质量,在4MPaH2和脉冲重复频率为10Hz时,喇曼过程的放热使前向喇曼的光束质量变坏,但对后向喇曼的光束质量影响不大.计算表明,该实验条件下受激喇曼过程没有达到稳态,所有实验结果都可以而且只能用相关的瞬态受激喇曼理论解释.     

大气前向自发喇曼散射的距离积累效应

通过数值求解大气前向自发喇曼散射功率的传播方程，从理论上发现了大气前向自发散射喇曼距离的积累效应。     

光孤子脉冲在光纤放大器中的传播

本文建立了包括增益色散,受激喇曼散射,双光子吸收效应的理论模型,讨论了光孤子脉冲在光纤放大器中的传播.数值计算结果表明:在反常色散范围内,光孤子的放大是不稳定的.增益色散导致光脉冲对称分裂,而受激喇曼散射则导致不对称的分裂.在增益色散和受激喇曼散射的共同作用下可获得新的时域和频域特征.有限带宽的放大能抑制受激喇曼散射引起的自频移.本文对有啁啾的光孤子脉冲的放大也进行了分析.     

有线性摆动器和轴向引导磁场的自由电子激光器的自发辐射及受激喇曼辐射

本文研究的自由电子激光器具有线性摆动器及轴向引导磁场.强流相对论冷电子束通过位在这些磁场中的平行平板波导。我们计算了它的自发辐射和受激喇曼辐射,给出了单位频率单位立体角的自发辐射功率和在电子静止坐标中的横电波(TE模)的受激喇曼辐射的色散关系和增益公式。     

c向静电场作用下α-LiIO_3单晶的喇曼谱“串线”和谱线强度改变的机理

在c向静电场作用下,α-LiIO_3单晶的喇曼谱发生“串线”,并且谱线强度改变。本文分析了这一现象的起因:由于离子输运引起的空间电荷涨落使α-LiIO_3单晶的极化率张量和喇曼张量主轴方向发生涨落。前者产生oe光散射,散射光再发生一次喇曼散射,造成喇曼谱“串线”和谱线强度的改变;后者直接造成喇曼诺“串线”和谱线强度的变化。前者的贡献远大于后者。     

新实验技术在材料研究中的应用讲座 第十讲 激光喇曼光谱及其应用

一、前 言 1928年 C.V.Raman和 K.S.Krishnan[1]公开发表了苯和甲苯的喇曼光谱.50多年来,喇曼光谱已成为研究分子振动的重要手段.特别在1961年Herzberg和Stoicheff提出使用激光作光源以后,Porto和Wood[2]在Columbs会议上报道了使用的效果,比用汞灯作为激发光源显示出巨大的优越性,使喇曼光谱进入了“文艺复兴”的新阶段.在此基础上,又发现了新的喇曼效应,应生了非线性喇曼光谱学[3],包括受激喇曼效应、倒喇曼效应、超喇曼效应、相干反斯托克斯喇曼散射以及电子喇曼效应等,在物理、化学、生物学和材料学等领域开展了广泛的探素研究,不仅…     

二维喇曼成像

Renishaw转换器系统的喇曼显微镜能提供二维喇曼成像和分析的最快方法。过去,由于喇曼扫描光效率很低,严重阻碍了喇曼的发展。不管怎样,该公司的方法是采用喇曼显微术,使仪器具有更大的光通量和探测效率。在很短的时间内用确定的喇曼光谱可鉴定微探针模型中样品的分子种类。在显微镜模型中,形成一个显示样品内部分子种类位置的图像。     

Tapered waveguide semiconductor raman laser

Semiconductor Raman laser can act as a heterodyne demodulator of terahertz-band modulated light wave signals in wideband optical communication systems. We have been developing the semiconductor Raman laser with a waveguide structure composed of a GaP core and Al_xGa_1–xP cladding layers. The tapered waveguide structure can reduce the threshold pump power by increasing the internal pump power density. Fabricated tapered waveguide semiconductor Raman laser have shown the threshold pump power of 160 mW. Discussion is made on the origin of losses as well as the limit of the low pump power operation.     

锥形脊结构半导体光放大器的有限元分析

为提高半导体光放大器与单模光纤耦合效率，建立了半导体放大器的锥形脊结构模型。在该模型下利用有限元数值模拟方法分析，计算了波导区折射率、锥尖宽度、条形波导尺寸、渐变折射率波导层对锥形脊结构模式扩展的影响。通过完善锥形脊结构参量的设计，获得了锥形脊结构半导体光放大器与单模光纤95％的耦合效率。     

95 GHz TE03模回旋管内置渐变波导设计

在耦合波理论的基础上,结合波导渐变曲线给出了普适高阶渐变波导设计方法,研究了95 GHz回旋管内置 TE03模式改进Dolph-Chebychev渐变波导。采用编制的数值计算程序进行优化,得到了可靠的最优几何参量,设计出了紧凑的95 GHz渐变波导。经全电磁场仿真验证,该内置渐变输出结构对杂模的抑制达30 dB,满足设计要求。回旋管的热测实验中测出的模式样图表明,所设计的内置渐变波导有效地实现了回旋管内径变化。该方法可以高效地指导高阶过模圆波导渐变结构的设计。     

95 GHz TE03模回旋管内置渐变波导设计

在耦合波理论的基础上,结合波导渐变曲线给出了普适高阶渐变波导设计方法,研究了95 GHz回旋管内置 TE03模式改进Dolph-Chebychev渐变波导。采用编制的数值计算程序进行优化,得到了可靠的最优几何参量,设计出了紧凑的95 GHz渐变波导。经全电磁场仿真验证,该内置渐变输出结构对杂模的抑制达30 dB,满足设计要求。回旋管的热测实验中测出的模式样图表明,所设计的内置渐变波导有效地实现了回旋管内径变化。该方法可以高效地指导高阶过模圆波导渐变结构的设计。     

Analysis of Semi-conductor Laser Diode with Two-dimension Nonlinearly Tapered Waveguide

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｈｉｇｈｅｆｆｉｃｉｅｎｔｃｏｕｐｌｉｎｇｂｅｔｗｅｅｎｃｈｉｐ(ｓｅｍｉｃｏｎｄｕｃｔｏｒｌａｓｅｒｄｉｏｄｅ)ａｎｄｓｉｎｇｌｅｍｏｄｅｆｉｂｅｒｉｓｔｈｅｋｅｙｔｅｃｈｎｏｌｏｇｙｆｏｒｏｐｔｏ ｅｌｅｃｔｒｏｎｉｃｓｉｎｔｅｇｒａｔｉｏｎｉｎｔｈｅｆｕｔｕｒｅｃｏｍｍｕｎｉｃａｔｉｏｎ[1 ] .Ｂｕｔｔ ｃｏｕｐｌｉｎｇｏｆｓｅｍｉｃｏｎｄｕｃｔｏｒｌａｓｅｒｄｉｏｄｅｗｉｔｈｓｉｎｇｌｅｍｏｄｅｆｉｂｅｒｌｅａｄｓｔｏｌａｒｇｅｃｏｕｐｌｉｎｇｌｏｓｓａｎｄｓｅ…     

Analysis of Semi-conductor Laser Diode with Two-dimension Nonlinearly Tapered Waveguide

A novel semiconductor laser diode with a two-dimension nonlinearly tapered waveguide is proposed and its property is studied by Fourier expanding method. It is shown that coupling loss between the semiconductor laser diode and a single mode fiber is reduced effectively, the reduction role of the nonlinearly tapered waveguide is more apparent than that of a linearly tapered waveguide , the minimum coupling loss is 0.36 dB, and the far field divergence is decreased. The reduction mechanism is discussed.     

Waveguide tapering for beam-width control in a waveguide transducer

In a waveguide transducer that transmits an ultrasonic wave through a waveguide unit to a test structure, it is most preferred to send a non-dispersive ultrasonic wave of a narrow beam width. However, there is an unresolved conflict between the generation of the non- or less-dispersive wave and the transmission of a narrow-beam wave into a test structure. Among others, the thickness of the waveguide unit in a waveguide transducer is the key variable determining these two conflicting criteria, but the use of a uniformly-thick waveguide of any thickness cannot fulfill the two conflicting criteria simultaneously. In this study, we propose a specially-engineered tapered waveguide unit for the simultaneous satisfaction. An excitation unit is installed at the end of the thin region of the tapered waveguide and generates only the lowest non-dispersive shear-horizontal wave. Then the generated wave propagates through the tapered region of the waveguide unit and reaches the thick region of the waveguide with insignificant mode conversion to higher modes. If the tapered waveguide is used, the surviving lowest mode in the thick region of the waveguide is shown to carry most of the transmitted power and is finally propagated into a test structure. Because the beam size of the propagated wave and the thickness of the contacting waveguide region are inversely related, the thick contacting region of the tapered waveguide ensures narrow beam width. Numerical and experimental investigations were performed to check the effectiveness of the proposed waveguide-tapering approach.     

低插损平坦谱响应阵列波导光栅解复用器优化设计

通过在输入波导与输入平板波导之间加入一种模式转换结构,获得了一个具有平坦光谱响应,低插损,光谱响应对称的阵列波导光栅型波分复用器,该模式转换结构由一个与输入波导的输出端连接的第一锥形波导,一个与此锥形波导输出端连接的细直波导,一个与细直波导输出端连接的第二个锥形波导以及一个连接输入平板波导和第二个锥形波导的梯形波导组成,通过优化设计梯形波导和第二个锥形波导的形状可以获得较宽的1dB通带带宽和较低的插损,同时光谱响应具有非常好的平坦性,而且通过对第一个锥形波导和细直波导的优化设计,在不引入明显的额外插损的条件下,能大大减小由于输入波导的弯曲引入的光谱响应的不平坦.     

Characteristics of Semi-conductor Laser Diode with Nonlinearly Tapered Waveguide

A novel semiconductor laser diode with nonlinearly tapered waveguide is proposed, and analyzed by a finite element beam propagation method (FM-BPM). The results show that the coupling efficiency is increased, and the laser's far field divergence is decreased effectively.     

Tapered microstructured fibers for efficient coupling to optical waveguides: a numerical study

We report the possibility of using tapered microstructured fibers to improve the coupling efficiency from a standard single-mode fiber to a photonic crystal waveguide. The tapered microstructured fiber allows for the reduction of the mode mismatch between the output of the standard fiber and the input of the waveguide while maintaining single-mode guidance, which results in an enhanced coupling efficiency. Numerical simulations are conducted in order to optimize the cross section of the microstructured fiber as well as the taper profile. An improvement of more than 4 dB is obtained compared to non-tapered fibers. For further improvement, an elliptical-core tapered microstructured fiber is analyzed. The effect of misalignment between the tapered microstructured fiber and the waveguide is also studied.