固相浸渍法制备NiO/CeO2催化剂及其在CO氧化反应中的应用

采用固相浸渍法制备了一系列NiO/CeO2催化剂,并通过与常规湿浸渍法比较,考察了制备方法对催化剂和CO氧化反应性能的影响.同时结合X射线衍射(XRD),N2吸附-脱附(BET),透射电镜(TEM),氢气-程序升温还原(H2-TPR),拉曼(Raman)光谱,X射线光电子能谱(XPS)等手段对催化剂的结构和表面物种分散状态进行了表征.CO氧化活性测试结果表明,当镍负载量相同时,固相浸渍法制备的催化剂相比于湿浸渍法表现出更好的催化性能.TEM、XPS、H2-TPR结果表明,固相浸渍法更有利于加强镍铈间的相互作用和得到高分散的镍物种,从而促进镍物种的还原.Raman结果表明固相浸渍法相比于湿浸渍法能产生更多氧空位,这有利于氧气在催化剂表面的活化,使得CO氧化反应更容易进行.     

Ni／MgO／Al2O3催化剂中Ni前体对甲烷—二氧化碳重整反应活性的影响

考察了以硝酸镍、氯化镍、硫酸镍、醋酸镍及硝酸六氨合镍5种Ni盐制备的Ni/MgO/Al2O3催化剂在CO2与CH4重整制合成气反应中的催化活性,发现Ni前体对活性有明显的影响,以硝酸镍、醋酸镍、硝酸六氨合镍为前体制备的Ni催化剂,反应性较高;以硫酸镍为前体制备的Ni催化剂,可能由于硫中毒等原因而显示出很低的活性;以氯化镍为前体制备的 Ni催化剂,其活性与制备方法有关,未经烧而直接还原的催化剂显示出较好的活性,X－射线粉末衍射（XRD）、BET比表面积及反应后的积量测定结果表明,以硝酸镍、醋酸镍、硝酸六氨合镍为前体制备的Ni催化剂,表面分散性好,比表面积大,积炭量少。     

Nucleation and particle growth in the preparation of silica-supported nickel catalysts by a two-step procedure

The mechanism of nucleation and growth of particles in the preparation of supported catalysts has been investigated in the case of the Ni/SiO₂ system. The separation of this two-step mechanism is achieved as follows:i) the “nickel nuclei” are prepared by ion-exchange or by impregnation followed by washing. They are in strong interaction with the support and act as anchoring sites for the metal particles.ii) The “nickel reservoir” constituted of nickel ion precursors and necessary for the nickel particle growth on the nuclei, is deposited by impregnation on the support. It is in weak interaction with the support and easily reducible. After temperature programmed reduction of the samples prepared by the above two-step procedure, the nickel particles are smaller and more homogeneous in size than those of catalysts prepared in one step by single impregnation of a pure silica support.     

助剂对Ni/海泡石催化剂加氢性能的影响

以海泡石为载体,Ｎｉ为活性组,用浸渍法制备了一系列含不同助剂的Ｎｉ基海泡石催化剂,以ＣＯ２甲烷化及苯加氢为探针反应,研究了催化剂的活性及抗硫性能,用Ｈ２－ＴＰＤ、ＸＰＳ、活性表面积及活化能的测定等于段,对催化剂进行表征,并从热力学上探讨ＣＯ２甲烷化的适宜温度。实验结果表明,海泡石或助剂的加入,能使镍晶粒变小,增加活性镍的表面积以及使镍原子的电子云密度升高,从而提高了催化剂的活性和使用寿命。能使镍晶     

Comparison of two preparation methods of supported Li?Ni catalyst on alumina for selective oxidation of methane

Lithium-added nickel catalysts on alumina were prepared for CO₂ reforming of methane by two methods, precipitation and impregnation. Performances of the catalysts were investigated by TG, CO-adsorption and SEM analysis. The catalyst with ratio of Li/Ni=1.0 prepared by precipitation method has high nickel dispersion, catalytic activity and stability for CO₂ reforming of methane.     

Temperature programmed reduction of silica supported nickel catalysts

Nickel oxide promoted catalysts are prepared by simple precipitation, precipitation from homogeneous solution and impregnation methods and their reduction behavior is monitored with temperature programmed reduction (TPR) technique. The effect of different parameters such as metal loading, method of preparation and heat treatment temperature are also observed on the reducibility of the catalysts. It is observed that reduction temperature increases with the increase of calcination temperature. Results indicate that the interactions between nickel oxide and silica begin with the increase of calcination temperature which leads to the formation of nickel hydrosilicates and are responsible for high temperature reduction peaks.     

Zr-Ni/Al2O3催化剂上苯由H2O2氧化直接氨基化制苯胺

用浸渍法制备了Ni／Al2O3和Zr-Ni／Al2O3催化剂，用于以过氧化氢为氧化剂的苯直接氧化胺化制苯胺反应，并对催化剂进行了程序升温还原、室温氧吸附和氢吸附及XRD表征，结果表明，我们所制的Ni基催化剂对苯胺的生成都有活性，加入Zr后，催化剂中Ni物种更分散，低温可还原物种增加，室温吸氧和吸氢能力都增强，反应活性和对目标产物的选择性增大，Zr一方面使Ni物种进一步分散，增大催化剂的吸氢量和表面可还原Ni物种，有利于C-H键的活化；同时Zr与Ni的相互作用，促进了低温可还原物种的生成，使催化剂室温吸氧量增大，有利于苯的氧化，这种Zr和Ni的协同作用提高了催化剂的活性和选择性，催化剂的制备方法影响Zr与Ni的协同作用，使含Zr的两个催化剂的活性和选择性显示出差异。     

TiO2对Ni/Al2O3催化剂CO甲烷化性能的影响

采用溶胶凝胶法制备了一系列不同TiO₂含量的TiO₂-Al₂O₃复合载体,并通过浸渍法制备了NiO/TiO₂-Al₂O₃催化剂。分别考察了不同TiO₂含量的NiO/TiO₂-Al₂O₃催化剂及反应温度对CO甲烷化催化性能的影响。实验结果表明,当复合载体中TiO₂质量分数为30%,反应温度为350～450 ℃时,催化剂催化活性较高。利用N₂吸附-脱附(BET)、X射线衍射(XRD)及H₂程序升温还原(H₂-TPR)等手段对催化剂物化性能进行了表征。结果表明,加入适量的TiO₂能抑制镍铝尖晶石NiAl₂O₄物种的生成,改善NiO的表面分散性能,避免大晶粒NiO的形成,也改善了催化剂的还原性能,从而提高催化剂的CO甲烷化活性。     

Ni/海泡石及Ni/Sm海泡石催化剂的研究(英文)

用浸渍法制备了一系列含镍的催化剂,以ＴＰＲ、ＴＰＤ、ＸＲＤ及ＸＰＳ等手段分别对Ｎｉ／海泡石及Ｎｉ／Ｓｍ海泡石催化剂进行了表征。结果表明,助剂钐的加入不仅使镍粒变小,而且也降低了镍原子结合能,除此以外,镍的分散亦有提高。ＴＰＲ与ＴＰＤ测试表明钐的加入亦能引起峰温的变化。     

Comparative Study of Nickel Catalysts Supported on X- and Y-Zeolites

We have made a comparative study of CO/H₂ reactions over the nickel catalysts supported on X- and Y-zeolites, prepared by incipient-wetness impregnation (W) and ion-exchange (E) methods. The catalysts were characterized by surface area and volumetric chemisorption measurements, temperature programmed reduction profiles, and x-ray diffraction analysis. The results show that the turnover frequency decreases in the order; NiX(W)>NiY(W)>NiY(E)>NiX(E). The metal dispersion and catalytic activity of the catalyst are mainly affected by the support materials, the preparation methods, and the activation procedures. The high activity of NiX(W) was due to its higher reducibility, smaller nickel crystalline size, and better nickel dispersion. The low activity of NiX(E) was attributed to the poor ion-exchange of Ni with NaX, the poor reducibility, the large crystalline size, and the poor nickel dispersion.     

制备方法对Ni/MgO/Al2O3催化剂在甲烷与二氧化碳重整反应活性的影响

采用浸渍－还原法制备的Ｎｉ／ＭｇＯ／Ａｌ２Ｏ３在ＣＨ４与ＣＯ２重整制合成气反应中显示出良好的催化性能和一定的抗积炭能力;在１０２３Ｋ下流动反应气氛中连续运转１００ｈ,未见活性下降,ＣＨ４及Ｃ弦均为９０％左右,ＣＯ收率高于９０％,实验还发现,ＣＨ４转化率随着原料气中ＣＯ２浓度的增加而升高,当Ｖ（ＣＯ２）／Ｖ（ＣＨ４）＝２时ＣＨ４转化率可达１００％,通过ＢＥＴ比表面积测定及ＸＲＤ,ＴＥＭ等分析手段,比     

NiO/LaMnO3催化剂用于乙醇水蒸气重整反应

采用柠檬酸络合-浸渍法制备了NiO/LaMnO3钙钛矿型复合氧化物催化剂并将其应用于乙醇水蒸汽重整制氢反应, 考察了NiO含量、焙烧温度对催化剂性能的影响, 采用XRD、TPR和热分析等手段对催化剂进行了表征. 结果表明, 该催化剂具有高活性、高选择性和良好的稳定性. 催化剂中的NiO含量和焙烧温度对催化性能有显著影响. 在原料气体积组成为20%(体积分数, φ) C2H5OH 和水以及80%(φ)N2, 其中水醇摩尔比为3:1, 空速为80000 mL·h-1·g-1 cat, 反应温度为400 ℃时, 15%(质量分数, w)的NiO/LaMnO3上, 乙醇转化率接近100%. 关联催化剂活性和TPR及XRD实验结果, 发现催化剂的高活性源于由催化剂前驱体中进入钙钛矿型复合氧化物晶格中的镍离子被还原所得的金属镍.     

Nickel supported carbon nanofibers as an active and selective catalyst for the gas-phase hydrogenation of 2-tert-butylphenol

Nickel supported fishbone carbon nanofibers (CNFs) have been prepared by vacuum impregnation (VI) and homogeneous deposition-precipitation (HDP) methods with different nickel loadings (ca. 5%, 9% and 12%) with the aim to study the influence of the metal incorporation method and the nickel loading in the catalytic activity of gas-phase hydrogenation of 2-tert-butylphenol (2-TBP). Moreover, the influence of the nature of the support was also studied by preparing nickel catalysts supported on other carbon (active carbon (AC) and graphite (G)) and non-carbonaceous materials (alumina (AL) and yttria-stabilized zirconia (YSZ)). Different techniques were employed to characterize both the supports and the final Ni catalysts: atomic absorption spectrometry, N(2) adsorption-desorption analysis, temperature-programed reduction (TPR), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Catalytic results revealed that the nickel particle size and support properties affected directly to both the catalytic activity of hydrogenation of 2-TBP, and the rate of secondary reactions such as cis to trans isomerization and 2-tert-butylcyclohexanone (2-TBCN) hydrogenation.     

制备条件对用于甘油蒸汽重整反应Ni基催化剂性能的影响

研究了制备参数对用于甘油蒸汽重整反应的Ni基催化剂性能的影响。采用过量浸渍法、等体积浸渍法和改进的平衡沉积过滤(EDF)法制备了一系列Al2O3负载的8 wt%Ni催化剂,运用X射线衍射(XRD)、电感耦合等离子体光谱仪、N2吸附-脱附、扫描电镜(SEM)、透射电镜和H2程序升温还原(TPR)表征了催化剂的表面和体相性质;采用CHN分析仪和SEM表征了使用后催化剂以测定其表面沉积的碳及其形貌。结果表明,制备方法对所制催化剂的织构、结构和表面性质影响很大,导致氧化铝表面Ni物种的分散和种类的不同。即使XRD和TPR结果证实形成了铝酸镍晶相,但Ni/Al-edf催化剂中β峰的贡献大于其它两个催化剂的,表明在这种情况下铝酸镍更容易还原。在550 oC以上CO2选择性增加和CO选择性不变,表明Ni/Al-wet和Ni/Al-edf催化剂可成功催化水汽变换反应。另外,650oC时Ni/Al-edf催化剂上甘油生成气相产物的转化率、氢气产率以及烯丙醇、乙醛和乙酸选择性最高,且它在所有催化剂中的积炭量也最低。将催化剂结构性质、分散度和还原性与其催化性能相关联,发现EDF法制得的催化剂比表面积和活性相分散度更高,更易被还原,因而其活性和生成H2的选择性更高,也更抗积碳。     

Activation of nickel–chromium hydrogenation catalysts with hydrogen

The kinetics of the reduction of nickel cations in nickel oxide and nickel–chromium catalysts whose oxide precursors have different structures has been investigated by thermal analysis. The reduction of nickel oxide with a hydrogen-containing gas takes place at 250–330°C. The apparent activation energy of this reaction is about 88 kJ/mol. The introduction of up to 30 at % chromium cations into the nickel oxide structure shifts the reduction temperature of nickel in the oxide phase to 300–450°C and increases the apparent activation energy of the reduction of nickel cations to ～108 kJ/mol. The introduction of 67 at % chromium into nickel oxide results in the formation of an oxide precursor with a spinel structure. The apparent activation energy of the reduction of nickel cations in this spinel is about 163 kJ/mol. The results of this study can be used in optimizing the composition of Ni-containing hydrogenation catalysts and their activation and operation conditions.     

甲烷干重整催化剂Ni/Al2O3表面积炭表征与分析

用蒸发法制备了Ni/Al2O3催化剂及浸渍法制备了Ni/α-Al2O3和Ni/γ-Al2O3催化剂, 并与商品天然气水蒸气重整催化剂Z118Y一起进行了甲烷干重整实验, 考察了各催化剂上表面积炭行为. 通过H2程序升温还原(H2-TPR)、BET(Brunauer-Emmett-Teller)比表面积分析、X射线衍射(XRD)、透射电镜(TEM)、热重-差式扫描量热(TG-DSC)、程序升温氢化(TPH)等表征手段对催化剂表面沉积炭的特性进行了表征. 结果表明, 各催化剂上至少存在三种形式的碳物种: 无定形碳、丝状碳及石墨碳. 由于载体性质不同, 各催化剂上沉积炭的种类及其含量有所差别. Z118Y、Ni/Al2O3及Ni/α-Al2O3催化剂上主要沉积丝状炭, 而Ni/γ-Al2O3催化剂上则主要是石墨碳. Ni/γ-Al2O3催化剂中金属Ni颗粒较小(小于15 nm)、粒径分布范围较窄、分散性较好, 能减少催化剂表面炭的沉积, 有效地抑制丝状碳的生长.     

Support Modification of Supported Nickel Catalysts for Hydrogen Production by Auto-thermal Reforming of Ethanol

Recent progress on support modification of supported nickel catalysts for hydrogen production by auto-thermal reforming of ethanol was reported in this review. Nickel catalysts supported on various materials, including metal oxides and metal oxide-stabilized mesoporous zirconias, were prepared by an incipient wetness impregnation method for use in hydrogen production by auto-thermal reforming of ethanol. Various experimental measurements such as NH₃-TPD (temperature-programmed desorption) and TPR (temperature-programmed reduction) were carried out to elucidate the different catalytic performance of supported nickel catalysts. It was revealed that acid property of supporting materials served as one of the important factors determining the catalytic performance. Hydrogen yield over nickel catalysts supported on metal oxides showed a volcano-shaped curve with respect to acidity of the supports. Among the catalysts tested, Ni/ZrO₂ catalyst with an intermediate acidity exhibited a superior catalytic performance. It was also observed that reducibility of nickel catalysts supported on metal oxide-stabilized mesoporous zirconias played a key role in determining the catalytic performance in the auto-thermal reforming of ethanol for hydrogen production. Hydrogen yield over nickel catalysts supported on metal oxide-stabilized zirconias increased with increasing reducibility of the catalysts (with decreasing TPR peak temperature of the catalysts).     

镍基气凝胶催化CH4-CO2重整制取合成气反应的研究 Ⅲ.影响催化剂积碳性能因素的探讨

考察了823K焙烧的干凝胶xNCA550、气凝胶aNCA550及浸渍型催化剂iNCA550在923K、1073K、1173K反应温度下的积碳行为，对催化剂表面碳的活性及类型进行了分析，并探讨了影响催化剂积碳的因素。实验结果表明，随反应温度的提高，催化剂的积碳能力减弱，尤以气凝胶催化剂aNCA550明显。催化剂的积碳主要发生在反应的初期，反应温度越高，到达积碳量相对稳定期所需要的时间越短；随着反应时间的延续，催化剂积碳量缓慢增长，并且表面碳的活性降低。催化剂的酸性和镍晶粒大小是影响其积碳性能的主要内在因素，而它们对积碳的影响程度受反应温度的影响，反应温度越高，催化剂表达酸性中心利于积碳的作用越小，小晶粒镍抑制催化剂积碳的能力越强。     

新型Ni基加氢催化剂的研究(英文)

以酸处理海泡石为载体,用浸渍法制备了一系列含不同助剂的Ｎｉ基海泡石催化剂。以二氧化碳甲烷化、苯加氢、抗毒及抗热实验对助剂的影响进行了考查。结果表明,助剂尤其是钐的加入能显著地提高Ｎｉ基催化剂的加氢活性、热稳定性及抗毒能力。     

1,2-二氯丙烷加氢脱氯制丙烯Ni/活化炭化树脂催化剂

镍催化剂;1;2-二氯丙烷加氢脱氯制丙烯Ni/活化炭化树脂催化剂