Tailoring the optical and hydrophobic property of zinc oxide nanorod by coating with amorphous graphene

Zinc oxide (ZnO) nanorods were synthesized at room temperature on potassium permanganate activated silicon and glass substrate by simple chemical method using zinc acetate as precursor.To modify the surface energy of the as prepared ZnO thin films the samples were coated with amorphous graphene (a-G) synthesized by un-zipping of chemically synthesized amorphous carbon nanotubes (a-CNTs). All the pure and coated samples were characterized by x-ray diffraction, field emission scanning electron microscope, Raman spectroscopy, and Fourier transformed infrared spectroscopy. The roughness analysis of the as prepared samples was done by atomic force microscopic analysis. The detail optical properties of all the samples were studied with the help of a UV-Visible spectrophotometer.The surface energy of the as prepared pure and coated samples was calculated by measuring the contact angle of two different liquids. It is seen that the water repellence of ZnO nanorods got increased after they are being coated with a-Gs. Also even after UV irradiation the contact angle remain same unlike the case for the uncoated sample where the contact angle gets decreased significantly after UV irradiation. Existing Cassie-Wenzel model has been employed along with the Owen's approach to determine the different components of surface energy.     

Fabrication and characterization of graphene oxide/zinc oxide nanorods hybrid

This work presented a hybrid architecture of graphene oxide (GO)/ZnO nanorods (ZNs) with ZNs attached parallel onto GO sheets. ZNs were synthesized by refluxing zinc acetate dehydrate in methanol solution under basic conditions followed by surface modification of 3-aminopropyl triethoxysilane (ATS), and then the preformed ZNs were attached onto GO sheets by reaction of the amino groups on the outer wall of ZNs with the carboxyl groups on the GO surface. Transmission electron microscopy (TEM) image of the as-prepared hybrid reveals the morphology of the architecture of GO/ZNs hybrid. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis (TGA) ultraviolet-visible (UV-vis) and fluorescence spectroscopy were also performed to characterize the structure and properties of the GO/ZNs hybrid. It was shown that ZNs maintained their initial morphology and crystallinity in the hybrid and the luminescence quenching of yellow-green emission of ZNs confirmed the electron transfer from excited ZnO to GO sheets.     

Contact passivation in silicon solar cells using atomic‐layer‐deposited aluminum oxide layers

Atomic‐layer‐deposited aluminum oxide (AlO_x) layers are implemented between the phosphorous‐diffused n⁺‐emitter and the Al contact of passivated emitter and rear silicon solar cells. The increase in open‐circuit voltage V_oc of 12 mV for solar cells with the Al/AlO_x/n⁺‐Si tunnel contact compared to contacts without AlO_x layer indicates contact passivation by the implemented AlO_x. For the optimal AlO_x layer thickness of 0.24 nm we achieve an independently confirmed energy conversion efficiency of 21.7% and a V_oc of 673 mV. For AlO_x thicknesses larger than 0.24 nm the tunnel probability decreases, resulting in a larger series resistance. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

基于石墨烯基电极染料敏化太阳能电池的研究进展

对近几年石墨烯基电极染料敏化太阳能电池的研究成果进行了追踪,分析了多种改性石墨烯电极应用于染料敏化太阳能电池后能量转换效率变化的原因,深入研究了改善石墨烯对电解质的还原电催化反应活性物理机理,为解决该电池存在的问题理清了思路,对该方向未来的研究工作给出了建议,探索和制备新材料以进一步打破石墨烯的层间堆叠是提高该电池性能的关键。     

Structural characterization of the sol–gel oxide powders from the ZnO–TiO2–SiO2 system

This work is a study that deals with the synthesis by the sol–gel method and the structural characterization of the oxide powders belonging to the ternary system ZnO–TiO₂–SiO₂ (ZTS). The sol–gel synthesis starts from inorganic precursors, which have been processed under the variation of different technological parameters. We have investigated the dependence of the gelling time on pH and on the temperature of synthesis as well as on water and ammonia amounts. In the case of ZTS samples, the shortest gelling duration appears for low pH values when ZnO content is increased and at small ammonia concentrations when the ZnO content is decreased, respectively. On the contrary, ZTS samples containing high amounts of TiO₂ provide evidence of a short gelling time for high pH and large ammonia amounts. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy provided structural information on these ternary oxide powders. These analyses revealed that relative high amounts of ZnO yields in a change from octahedral [ ZnO₆] units to tetrahedral [ ZnO₄] units in the powder structure. Optical phonons specific for SiO₂ and TiO₂ in both octahedral and tetrahedral groups are shown. High thermal and chemical stability was put in evidence by differential thermal analysis (DTA) and thermo-gravimetric analysis (TGA) in the 20–1000 C temperature range.     

Fabrication and characterization of zinc oxide anti-reflective coating on flexible thin film microcrystalline silicon solar cell

This paper studies the fabrication and characterization of 80 nm zinc oxide anti-reflective coating (ARC) on flexible 1.3 μm thin film microcrystalline silicon (μc-Si) solar cell. High resolution X-ray diffraction (HR-XRD) shows a c-axis oriented ZnO (0 0 2) peak (hexagonal crystal structure) at 34.3° with full width at half maximum (FWHM) of 0.3936°. Atomic force microscope (AFM) measures high surface roughness root-mean-square (RMS) of the layer (50.76 nm) which suggests scattering of the incident light at the front surface of the solar cell. UV–vis spectrophotometer illustrates that ZnO ARC has optical transmittance of more than 80% in the visible and infra-red (IR) regions and corresponds to band gap (E_g) of 3.3 eV as derived from Tauc equation. Inclusion of ZnO ARC successfully suppresses surface reflectance from the cell to 2% (at 600 nm) due to refractive index grading between the Si and the ZnO besides quarter-wavelength (λ/4) destructive interference effect. The reduced reflectance and effective scattering effect of the incident light at the front side of the cell are believed to be the reasons why short-circuit current (I_sc) and efficiency (η) of the cell improve.     

Light‐induced degradation of PECVD aluminium oxide passivated silicon solar cells

Light‐induced degradation (LID) has been identified to be a critical issue for solar cells processed on boron‐doped silicon substrates. Typically, Czochralski‐grown silicon (Cz‐Si) has been reported to suffer from stronger LID than block‐cast multicrystalline silicon (mc‐Si) due to higher oxygen concentrations. This work investigates LID under conditions practically relevant under module operation on different cell types. It is shown that aluminium oxide (AlOx) passivated mc‐Si solar cells degrade more than a reference aluminium back surface field mc‐Si cell and, remarkably, an AlOx passivated Cz‐Si solar cell. The defect which is activated by illumination is shown to be doubtful a sole bulk effect while the AlOx passivation might play a certain role. This work may contribute to a re‐evaluation of the suitability of boron‐doped Cz‐ and mc‐Si for solar cells with very high efficiencies. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Hybrid solar cells with conducting polymers and vertically aligned silicon nanowire arrays: The effect of silicon conductivity

Organic/inorganic hybrid solar cells, based on vertically aligned n-type silicon nanowires (n-Si NWs) and p-type conducting polymers (PEDOT:PSS), were investigated as a function of Si conductivity. The n-Si NWs were easily prepared from the n-Si wafer by employing a silver nanodot-mediated micro-electrochemical redox reaction. This investigation shows that the photocurrent-to-voltage characteristics of the n-Si NW/PEDOT:PSS cells clearly exhibit a stable rectifying diode behavior. The increase in current density and fill factor using high conductive silicon is attributed to an improved charge transport towards the electrodes achieved by lowering the device's series resistance. Our results also show that the surface area of the nanowire that can form heterojunction domains significantly influences the device performance.     

Metal oxide buffer layer for improving performance of polymer solar cells

We report the application of aluminum doped ZnO (ZnO:Al) layer as a buffer on ITO glass for fabrication of non-inverted polymer solar cells. The ZnO:Al thin film was deposited using DC magnetron sputtering, with the thickness being varied from 23 to 100 nm. The devices showed most discernible improvements in their efficiencies when a thin layer of ZnO:Al film of thickness ∼40 nm was introduced. The observed enhancement in short circuit current density and open circuit voltage is likely attributed to the role of the ZnO:Al film as an optical tuner and an interfacial diffusion barrier. The result suggests that a metal oxide layer inserted between ITO and polymer layers can be a route for improving both efficiency and stability of polymer solar cells.     

Nanostructured solar cell based on solution processed Cu2ZnSnS4 nanoparticles and vertically aligned ZnO nanorod array

Cu₂ZnSnS₄ (CZTS) has attracted intensive interest for application in photovoltaic technology due to its excellent semiconductor properties. We report a nanostructured CZTS solar cell which was fabricated by infiltrating of CZTS nanoparticles into CdS coated ZnO nanorod arrays. The well aligned ZnO nanorods facilitate the efficient infiltration of CZTS nanoparticles. A hole transport layer was deposited to facilitate the transport of holes. The nanostructured CZTS solar cell demonstrated a remarkably high short‐circuit current density (11.0 mA/cm²). As a result, a power conversion efficiency of 2.8% was obtained. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Dopant‐free back contact silicon heterojunction solar cells employing transition metal oxide emitters

The present study investigates the electrical properties of transition metal oxide (TMO) emitters in dopant‐free n‐Si back contact solar cells by comparing the properties of solar cells employing three TMOs (WO_x, MoO_x and V₂O_x) with varying electrical properties acting as p‐type contacts. The TMOs are found to induce large band bending in n‐Si, which reduces the injection level dependent interfacial recombination speed S_eff and contact resistivity ρ_c. Among the TMO/n‐Si contacts considered, the V₂O_x/n‐Si contact achieves the lowest S_eff of 138 cm/s and ρ_c of 0.034 Ω cm², providing the significant advantages over heavily doped a‐Si:H(p)/n‐Si contacts. The best device performance was achieved by the V₂O_x/n‐Si solar cell, demonstrating an efficiency of 16.59% and an open‐circuit voltage of 610 mV relative to solar cells based on MoO_x/n‐Si (15.09%, 594 mV) and WO_x/n‐Si (12.44%, 539 mV). Furthermore, the present work is the first to employ WO_x, V₂O_x and Cs₂CO₃ in back contact solar cells. The fabrication process employed offers great potential for the mass production of back contact solar cells owing to simple, metal mask patterning with high alignment quality and dopant‐free steps conducted at a lower temperature.     

Microwave-reduced graphene oxide for efficient and stable hole extraction layers of polymer solar cells

Microwave-assisted reduced graphene oxide (MR-GO) layer was applied to hole extraction layer (HEL) of polymer solar cells (PSCs) and was compared with the widely used poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) in bulk hetero-junction (BHJ) solar cells. The power conversion efficiency (PCE) of 3.57% was achieved with the MR-GO layer, which is 21% higher than that of PSCs with the conventional PEDOT:PSS HEL material. This enhancement of PCE is mainly attributed to the increase of short-circuit current density originated from the hydrophobic surface of the MR-GO layer. The hydrophobic graphene oxide surface is believed to improve wetting property and physical contact of active blends. In addition, the MR-GO interfacial layer is found to show the excellent device stability in atmospheric condition. The PCE of conventional PEDOT:PSS based PSCs showed total degradation when the device was exposed to atmospheric condition for 1000 h without any encapsulation, while that of MR-GO based PSC showed over 85% of PCE.     

Effect of III‐nitride polarization on VOC in p–i–n and MQW solar cells

We performed detailed studies of the effect of polarization on III‐nitride solar cells. Spontaneous and piezoelectric polarizations were assessed to determine their impacts upon the open circuit voltages (V_OC) in p–i(InGaN)–n and multi‐quantum well (MQW) solar cells. We found that the spontaneous polarization in Ga‐polar p–i–n solar cells strongly modifies energy band structures and corresponding electric fields in a way that degrades V_OC compared to non‐polar p–i–n structures. In contrast, we found that piezoelectric polarization in Ga‐polar MQW structures does not have a large influence on V_OC compared to non‐polar MQW structures. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Enhanced efficiency and stability of polymer solar cells using solution-processed nickel oxide as hole transport material

Solution-processed nickel oxide (s-NiO_x) was synthesized for use as hole-transport layers (HTLs) in the fabrication of polymer solar cell (PSC) devices. The s-NiO_x thin-films were deposited using spin-coating and post-annealed at 300 °C, 400 °C, or 500 °C. With increased annealing temperature, the nickel acetate precursor decomposes more fully and forms s-NiO_x films that show larger crystalline grain sizes with lower root mean square surface roughness. Bulk heterojunction solar cells fabricated with the new random polymer RP(BDT-PDBT) and [6,6]-phenyl-C₇₀-butyric acid methyl ester (PC₇₀BM) using s-NiO_x as HTLs exhibit a 4.46% enhancement in power conversion efficiency and better stability compared to conventional PSCs using poly (3,4-ethylenedioxythiophene):poly(styrene sulfonate) as HTLs. We believe that the solution-processable and highly stable s-NiO_x could be a potential alternative for functional interface materials in optoelectronic devices.     

Hybrid polymer/inorganic nanoparticle blended ternary solar cells

Hybrid polymer/inorganic nanoparticle blended ternary solar cells are reported. These solar cells have an active layer consisting of PbS colloidal quantum dots (CQDs), poly (3‐hexylthiophene) (P3HT), and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM). Power conversion efficiency (PCE) was improved by incorporating PbS CQDs in the active layer of P3HT:PCBM‐based organic solar cells. As the concentration of PbS CQDs in the hybrid solar cells was increased, PCE was also increased. This improvement resulted from improved charge transfer and also extended light absorption into the near‐infrared. The PCE of the hybrid solar cells was 47% higher than that for reference organic solar cells on average under air mass 1.5 global illumination. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Nongeminate recombination in organic bulk heterojunction solar cells: Contribution of exciton–polaron interaction

A new model to explain nongeminate recombination in organic bulk heterojunction solar cells is presented. We suggest that the annihilation of excitons on charge carriers at the interface between donor and acceptor phases competes with the bimolecular recombination of Coulombically bound electron–hole pairs. The exciton–polaron interaction gives visible contribution to the reduction of Langevin recombination. An analytical formula, which describes the reduction prefactor, has been derived. We demonstrate that exciton–charge carrier interactions cause an increase of the recombination order. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Improved performance of TiO2 electrodes coated with NiO by magnetron sputtering for dye-sensitized solar cells

TiO₂ electrodes are coated with NiO by DC magnetron sputtering, and their structural, optical and electrochemical performance has been investigated. X-ray diffractometry (XRD), UV-vis spectrophotometry, scanning electron microscopy (SEM), AC impedance, and linear sweep voltammetry (LSV) are used to characterize the TiO₂/NiO electrodes. Their performance is evaluated with a computer controlled electrochemical workstation in combination with three conventional electrodes. The experimental results indicate that the surface modification of TiO₂ electrodes with sputtered NiO reduces trap sites on TiO₂ and improves the electrochemical performance of dye-sensitized solar cells (DSSCs). Sputtering NiO for 7 min, which is about 21 nm thick, on 6.5 μm thick TiO₂ greatly improves the DSSC parameters, and the conversion efficiency increases from 3.21 to 4.16%. Mechanisms of the influence of the NiO coating on electrochemical performance are discussed.     

Assessing the antimicrobial activity of zinc oxide thin films using disk diffusion and biofilm reactor

The electronic and chemical properties of semiconductor materials may be useful in preventing growth of microorganisms. In this article, in vitro methods for assessing microbial growth on semiconductor materials will be presented. The structural and biological properties of silicon wafers coated with zinc oxide thin films were evaluated using atomic force microscopy, X-ray photoelectron spectroscopy, and MTT viability assay. The antimicrobial properties of zinc oxide thin films were established using disk diffusion and CDC Biofilm Reactor studies. Our results suggest that zinc oxide and other semiconductor materials may play a leading role in providing antimicrobial functionality to the next-generation medical devices.     

Measurement of mixed conductivity in thin films with microstructured Hebb–Wagner blocking electrodes

Determination of the ionic and electronic contributions to the total conductivity in mixed ionic–electronic conductors (MIEC) is central to understanding their properties, particularly in nanostructured ionic solids. The Hebb–Wagner blocking technique, commonly used to deconvolute ionic and electronic contributions in bulk MIECs, is susceptible to misinterpretation when applied to thin films. In this work, microfabricated electronic blocking electrodes consisting of porous Pt on dense thin yttria-stabilized zirconia (YSZ) films were applied to nanocrystalline CeO₂ thin films. The validity of the blocking structure was expressly considered with respect to alternate current and gas phase reaction pathways, with criteria developed to aid in identifying spurious effects. The ionic partial conductivity in nanocrystalline CeO₂ thin films was confirmed to be pO₂-independent while the electronic partial conductivity was found to be pO₂ dependent with a power dependence of − 0.31 ± 0.02. These results are compared with theoretical predictions of extrinsically-compensated ceria and previous results on bulk nanocrystalline ceria.