Atom transfer radical polymerization (ATRP) of ethyl acrylate was carried out in bulk using ethyl 2-bromoisobutyrate as initiator, CuBr as well as CuCl as catalyst in combination with different ligands e.g., 2,2′ bipyridine (bpy)andN,N, N′,N″,N″-pentamethyldiethylenetriamine (PMDETA). In most of the cases very high conversion (72–98%) was achieved. The polymerization was well controlled with a linear increase of molecular weight (MnSEC) with conversion and relatively narrow molecular weight distributions (polydispersity index 1.2–1.3). Use of PMDETA as the ligand resulted in faster polymerization rate (98% conversion in 1 h) than those using bipyridine (72% conversion in 5 h). The MALDI-TOF-MS analysis of poly (ethyl acrylate) (PEA) prepared by using bpy as ligand showed the presence of halogen as the end group. On the contrary, when PMDETA was used as the ligand, the mass analysis showed no trace of this end group. 相似文献
Kinetic simulations using the composite kt model allows a better understanding of the effects of the persistent radical affecting ATRP or for that matter any activation–deactivation system. It also provides a better fit to experimental data in either bulk or solution conditions for ATRP polymerizations carried out at 110 °C. The results suggest that the composite model has broad utility over a wide range of experimental conditions and temperatures. The advantage of incorporating an accurate kt model is that one can then use simulations as predictive tool to obtain polymers with higher chain‐end fidelity or polymers with low PDI values. This becomes important when attempting to use the chain‐ends for further functionalization to make complex polymer architectures. This model can also be used in simulations of miniemulsion or seeded emulsions to determine the effect of compartmentalization with particle size.
Summary: Controlled copolymerization of polar (meth)acrylates with non-polar olefin monomers (1-octene, norbornene, vinylcyclohexane) was studied by ARGET (activators regenerated by electron transfer) ATRP (atom transfer radical polymerization). When a normal ATRP of n-butyl acrylate (nBA) and 1-octene was conducted, the polymerization resulted in relatively low conversion, limited control over the polymerization process and high polydispersity (PDI > 1.6). This was due to formation of a dormant species, by reaction of 1-octene radicals with Cu(II) deactivator, that could not be reactivated. However, in ARGET ATRP with 10 ppm amounts of Cu-based catalyst, higher yields and a better controlled copolymerization was obtained (PDI < 1.4), because the low concentration of Cu(II) deactivator reduced the formation of the non-reactive dormant species. The influence of the amount of Cu catalyst, ligand structure, initiators with different halogens, the reaction temperature, and monomer feed ratio were also investigated for ARGET ATRP. In copolymerization of (meth)acrylates with non-polar alkenes, the level of control and the total conversion in ARGET ATRP were higher than those for normal ATRP. 相似文献
A simple method has been described to remove catalyst from the copper mediated atom transfer radical polymerization (ATRP) of benzyl methacrylate and methyl methacrylate in anisole at 25 °C using hydrated natural clay (sodium montmorillonite, Na‐clay). The method consists of (1) addition of hydrated clay (CuI/clay ≈ 5 wt.‐%) either during or after the polymerization, (2) oxidation of catalyst complex by exposing the terminated reaction mixture in air, and (3) filtration to obtain catalyst free polymer solution. A strong coordination of CuBr‐ligand complex onto hydrated clay (10 wt.‐% < H2O/clay < 30 wt.‐%) upon oxidation resulted in polymers with no or insignificant residual catalyst (<1.74 ppm), as determined by UV‐vis and atomic absorption spectroscopy. The recovered clay exhibited expanded intercalary layers and absence of polymer within it.
