溶剂热制备锂电池负极材料CNT-ZnFe2O4及其电化学性能

为了改善锂离子电池负极材料ZnFe₂O₄导电性差和循环寿命低的缺点,利用溶剂热反应方法制备了ZnFe₂O₄,并通过复合碳纳米管对ZnFe₂O₄进行改性。充放电测试结果表明：经过50次充放电后,碳纳米管复合改性后的ZnFe₂O₄容量保持在860 mA·h·g^-1,具有较好的循环稳定性。碳纳米管具有良好的导电性与导热性,改善了ZnFe₂O₄导电性差的缺点。     

溶液燃烧法合成纳米ZnFe2O4晶体

采用溶液燃烧法合成了ZnFe₂O₄纳米晶体,系统考察了不同燃料,燃料/氧化剂的摩尔比对ZnFe₂O₄晶相组成和形貌的影响。采用XRD和SEM对产物的晶相组成、晶粒大小、晶体形貌以及表面形态进行了表征。结果表明:燃料种类和燃料/氧化剂比对合成产物晶相组成影响显著。以丙氨酸和甘氨酸为燃料合成所得的纳米晶相较好;以丙氨酸和甘氨酸为燃料时,都是在贫燃（—50%）时得到最好ZnFe₂O₄纳米晶型,尺寸分别为34.4nm和29.7nm。     

尖晶石LiMn2O4及其衍生物的电化学阻抗特性

尖晶石LiMn2O4(以下简称LMO)是锂离子电池正极材料之一，具有价格低廉，资源丰富的特点。锂离子电池的充放电过程实际上是锂离子从正极脱嵌、再嵌入正极的过程。因此Li^ 在正负极材料及电解液中的扩散性能影响着电池的电性能，通过其电化学阻抗谱可得出锂离子的扩散系数及电导率等参数。     

同步辐射XAFS研究高比能LiMn2O4材料的局域结构

用EXAFS和XANES技术研究了高温固相反应法合成尖晶石结构的LiMn2O4中Mn原子的局域结构受到焙烧温度的影响.XANES结果表明,B1峰和B2峰强度分别与Mn3+,Mn4+的含量高低相关,焙烧温度愈高,B1峰的强度愈大.EXAFS给出的结构参数结果进一步表明,LiMn2O4(673K)的Mn-O第一配位和MnMn第二配位的无序度σ1(0.0059nm)和σ2(0.0092nm)分别小于及大于LiMn2O4(973K)的σ1(0.0066nm)和σ2(0.0081nm),LiMn2O4(1073K) 关键词： XAFS 局域结构 尖晶石LiMn2O4     

LiNi1-x-yCoxMnyO2正极材料的制备与电化学性能

LiNi_1-x-yCo_xMn_yO₂正极材料作为最有商业化前途的锂离子电池正极材料,近年来成为研究者关注的焦点。但目前针对该材料合成工艺的研究还较少。对LiNi_0.8Co_0.15Mn_0.05O₂开展了不同的烧结工艺研究,并对制备出的正极材料进行了表征和性能测试。研究发现在0.1C (电池容量额定值)倍率下充放电比容量为200 mA·h·g-1左右,在1C倍率循环100次下,480 ℃@3 h + 780 ℃@5 h和500 ℃@5 h + 780 ℃@10 h两种烧结工艺下容量保持率分别为94%和86%,说明用这两种工艺制备的正极材料的综合性能最优。     

Mn3O4包覆对LiNi0.5Mn1.5O4正极材料界面电化学性能的提高

本文采用化学湿磨法,首次将金属氧化物Mn₃O₄包覆于LiNi_0.5Mn_1.5O₄颗粒表面,使得电极材料的电子电导率从1.53×10^-7 S/cm 提高到3.15×10^-5 S/cm. 电化学测试结果表明Mn₃O₄包覆大大提高LiNi_0.5Mn_1.5O₄正极材料的倍率性能和高温循环稳定性. 最佳包覆样品为2.6wt% Mn₃O₄包覆的LiNi_0.5Mn_1.5O₄,在10 C倍率下具有108 mAh/g的高放电容并且在55 °C下100次循环后仍有78%的容量保持率,远大于未包覆样品67%的容量保持率.     

静电纺丝法制备Bi2Fe4O9及其磁学性能的研究

采用静电纺丝法合成了纤维状的Bi₂Fe₄O₉前驱体,再对前驱体进行热处理得到了棒状的Bi₂Fe₄O₉.通过X射线衍射、扫描电子显微镜及透射电子显微镜表征了合成样品的物相及形貌特征.结果表明合成的样品为Bi₂Fe₄O₉单相,属于正交晶系;退火处理导致纤维状的前驱体转变为棒状的Bi₂Fe₄O₉.紫外-可见吸收光谱表明制备的Bi₂Fe₄O₉对光的吸收范围广,不仅对紫外光具有较强吸收,而且对可见光也有一定的吸收.通过振动样品磁强计测定Bi₂Fe₄O₉磁滞回线研究其磁学特性,相应的矫顽力H_C≈82 Oe（1 Oe=79.5775 A/m）,剥离顺磁信号后的剩磁M_r≈0.25 emu/g,研究发现Bi₂Fe₄O₉样品具有弱铁磁性,并且软磁性能有所提高.     

Co$lt;sub$gt;2$lt;/sub$gt;SnO$lt;sub$gt;4$lt;/sub$gt;/Graphene复合材料的制备与电化学性能研究

实验首先采用改进的Hummers法制备氧化石墨,然后以氧化石墨烯为前驱体,通过水热法将锡酸钴纳米颗粒均匀镶嵌在石墨烯薄膜基片上,最终获得Co₂SnO₄/Graphene镶嵌复合材料. 采用X射线衍射（XRD）、扫描电子显微镜（SEM）对材料的结构和形貌进行表征,通过恒电流充放电（CC）、循环伏安法（CV）与交流阻抗法（EIS）测试了材料的电化学性能. 实验结果表明,石墨烯良好的分散性及较高的电子导电率,可以提高锡酸钴材料的电化学性能,材料首次可逆容量达到1415.2 mA·h/g,50次循环后仍能保持469.7 mA·h/g的放电比容量. 关键词： 2SnO₄')" href="#">Co₂SnO₄ 石墨烯 电化学性能 锂离子电池     

热分解法制备MnFe2O4纳米粒子及其超顺磁性

采用热分解法制备了单相的锰铁氧纳米颗粒,X射线衍射以及透射电镜测量显示其颗粒大小约为20 nm.磁滞回线测量显示室温超顺磁性.零场和非零场磁测量显示制备的MnFe2O4纳米粒子平均截止温度为84.3 K,样品中最大颗粒的截止温度为230 K,且平均截止温度与外场H2/3存在线性关系.     

NiFe2O4纳米线阵列的制备与磁性

在氧化铝模板的纳米孔洞中, 用电化学的方法沉积铁镍合金纳米线，经过550℃30h氧化处理 , 成功制备出 NiFe2O4纳米线阵列. 分别用扫描电子显微镜 (SEM) 、透射电 子显微镜 (TEM) 、x射线衍射仪 (XRD) 和振动样品磁场计 (VSM) 对样品的形貌、晶体结构 和磁学性质进行了表征测试. SEM和TEM观察结果显示氧化铝模板的孔洞分布均匀，孔心距约 为110nm; 纳米线的直径约为70nm. XRD显示纳米线阵列的物相结构为NiFe2O4; VSM测试结果表明，NiFe2O4纳米线阵列膜的易磁化方向垂直于膜面. 当垂直 磁化时磁滞回线的矩形比约为05，矫顽力为41×103A/m，比氧化处理前的铁镍合金 纳米线阵列都有显著提高. 关键词： 纳米线 Ni Fe2O4 矫顽力     

熔融盐法合成锂离子电池正极材料纳米LiNiO2

采用熔融盐法,在较低的温度和较短的时间制备了符合理论化学计量比的纳米LiNiO₂.研究表明,经过空气中的低温预烧,可以使制备的纯相纳米LiNiO₂具有更加优良的结晶性能和更佳的电化学特性.添加预烧步骤前后所得最终产物的初始容量分别为151和148 mAh ·g^-1,经过100周的循环,容量衰减到55和118 mAh ·g^-1,容量保持率分别为36.4%和79.7%.原因在于预烧后再进行煅烧降低了阳离子无序度,减少了混杂 关键词： 2')" href="#">LiNiO₂ 熔融盐法 锂离子电池 电化学性能     

Characterization and electrochemical performance of the spinel LiMn2O4 prepared from -MnO2

The preparation and characterization of the spinel LiMn₂O₄ obtained by solid state reaction from quasi-amorphous -MnO₂ is reported. A well-defined highly pure spinel was characterized from X-ray diffractograms. The average manganese valence of -MnO₂ and spinel samples was found to be 3.89±0.01 and 3.59±0.01, respectively. The electrochemical performance of the spinel was evaluated through cyclic voltammetry and chronopotentiometry. The voltammetric profiles obtained at 1 mV/s for the LiMn₂O₄ electrode in 1 M LiClO₄ dissolved in a 2:1 mixture of ethylene carbonate and dimethyl carbonate showed typical peaks for the lithium insertion/extraction reactions. The charge capacity of this electrode was found to be 110 mA h g⁻¹ for the first charge/discharge cycles.     

The study of transition on NiFe2O4 nanoparticles prepared by co-precipitation/calcination

In this study, the NiFe₂O₄ nanoparticles have been prepared by co-precipitation and calcination process. Using a vibrating sample magnetometer (VSM), transmission electron microscopy (TEM), X-ray diffraction (XRD), energy dispersive spectrometer of X-ray (EDX), and X-ray photoelectron spectroscopy (XPS), the samples obtained by co-precipitation and then by further calcination have been analyzed. The experimental results show that the precursor synthesized by co-precipitation is the composite of both amorphous FeOOH and Ni(OH)₂, but has no amorphous NiFe₂O₄. The results of both EDX and XPS revealed that the FeOOH species is wrapped up by Ni(OH)₂ species. In the calcination process, the amorphous composite is dehydrated and transformed gradually into crystalline NiFe₂O₄ nanoparticles, with the metal ions diffusing. The reaction is different from the one used to prepare other ferrite (e.g., CoFe₂O₄, MnFe₂O₄, Fe₃O₄, etc.) nanoparticles directly by co-precipitation. With increasing calcination temperature, the NiFe₂O₄ grains grow and the magnetization is enhanced.     

Phosphorescent and thermoluminescent properties of SrAl2O4:Eu,Dy phosphors prepared by solid state reaction method

Long persistent SrAl₂O₄:Eu²⁺ phosphors co-doped with Dy³⁺ were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl₂O₄ were observed in all the samples. The broad band emission spectra at 497 nm for SrAl₂O₄:Eu²⁺, Dy³⁺ were observed and the emission is attributed to the 4f⁶5d¹ to 4f⁷ transition of Eu²⁺ ions. The samples annealed at 1100–1200 °C showed similar broad TL glow curves centered at 120 °C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy³⁺ ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.     

Preparation of TiO2-coated LiMn2O4 by carrier transfer method

The TiO₂-coated LiMn₂O₄ has been prepared by a carrier transfer method and investigated. This novel synthetic method involved the transfer of TiO₂ into the surface of LiMn₂O₄ with Vulcan XC-72 active carbon powders as a dispersant. The X-ray diffraction shows that spinel structure of materials does not change after the coating of TiO₂. The electrochemical performance tests show that the initial discharge capacity of TiO₂-modified LiMn₂O₄ is 111.5 mA h g⁻¹, which is better than that of pristine LiMn₂O₄ (103.8 mA h g⁻¹). The cyclic performance is significantly improved after surface modification. The TiO₂-modified LiMn₂O₄ by a carrier transfer method exhibits better discharge capability and lower resistance.     

Improvement of electrochemical performance of all-solid-state lithium secondary batteries by surface modification of LiMn2O4 positive electrode

To improve the electrochemical performance of an all-solid-state In/80Li₂S⋅20P₂S₅ (electrolyte)/LiMn₂O₄ cell, a lithium-titanate thin film was used to coat LiMn₂O₄. The interfacial resistance between LiMn₂O₄ and the electrolyte (measured after initial charging) decreased when the LiMn₂O₄ particles were coated with lithium-titanate. A cell with lithium-titanate-coated LiMn₂O₄ had a higher capacity than a cell with noncoated LiMn₂O₄ for current densities in the range 0.064 to 2.6 mA cm^− 2. Additionally, a cell with coated LiMn₂O₄ retained 96% of the 10th-cycle reversible capacity at a current density of 0.064 mA cm^− 2 after 50 cycles.     

Preparation of Bi2Fe4O9 particles by hydrothermal synthesis and functional properties

In the present study, particles with different Bi₂Fe₄O₉ micro/nanostructures with a few particular morphologies (flower-like nanoplatelets, hierarchical microstructures, perfectly square platelets single crystals, etc.) obtained under specific hydrothermal synthesis conditions were investigated. The role of the processing parameters (such as NaOH concentration, reaction temperature, and reaction duration time) on the phase formation mechanism and on the microstructural characteristics was investigated. All the Bi₂Fe₄O₉ morphologies showed orthorhombic symmetry with space group Pbam. The photocatalytic properties and magnetic behavior as a function of the micro/nanostructural characteristics of various Bi₂Fe₄O₉ powders were determined. In the presence of Bi₂Fe₄O₉, a degradation rate of Rose Bengal in the range of 52–61% was determined after 180?min under UV light irradiation (λ?=?254?nm). Magnetic activity with antiferromagnetic behavior and a transition at ～240?K slightly dependent on the microstructures was found. The role of Bi₂Fe₄O₉ microstructures in the photocatalytic activity and magnetic properties was discussed.     

LixFePO4(x=0.0, 0.75, 1.0)电子结构与弹性性质的第一性原理研究

采用基于密度泛函理论的第一性原理研究方法,计算了不同嵌锂态Li_xFePO₄(x=0,0.75,1.0)的电子结构. 对于橄榄石型Li_xFePO₄正极材料,虽然Fe3d电子在费米能级附近相互交错,但由于受晶体场作用的限制,并不能真正成为自由电子,Fe3d电子对体系的导电性没有很大贡献,而Fe—O键在低能成键区形成p-d杂化的局域态共价键对稳定合金骨架具有重要作用. 随着锂离子的脱 关键词： 锂离子电池 4')" href="#">LiFePO₄ 电子结构 弹性性质     

Investigation of 4H—SiC metal—insulation—semiconductor structure with Al2O3/SiO2 stacked dielectric

Atomic layer deposited (ALD) Al₂O₃/dry-oxidized ultrathin SiO₂ films as high-k gate dielectric grown on the 8° off-axis 4H-SiC (0001) epitaxial wafers are investigated in this paper. The metal-insulation-semiconductor (MIS) capacitors, respectively with different gate dielectric stacks (Al₂O₃/SiO₂, Al₂O₃, and SiO₂) are fabricated and compared with each other. The I-V measurements show that the Al₂O₃/SiO₂ stack has a high breakdown field ( ≥ 12 MV/cm) comparable to SiO₂, and a relatively low gate leakage current of 1× 10^-7 A/cm² at electric field of 4 MV/cm comparable to Al₂O₃. The 1-MHz high frequency C-V measurements exhibit that the Al₂O₃/SiO₂ stack has a smaller positive flat-band voltage shift and hysteresis voltage, indicating less effective charge and slow-trap density near the interface.