Sensitive detection of organophosphates in river water by means of a piezoelectric biosensor

A highly sensitive piezoelectric biosensor has been developed for detection of cholinesterase inhibitors. The inhibitor benzoylecgonine-1,8-diamino-3,4-dioxaoctane (BZE-DADOO) was immobilized on a monolayer of 11-mercaptomonoundecanoic acid (MUA) self-assembled on the gold surface of the sensor. The binding of high-molecular-weight cholinesterase to the immobilized cocaine derivative was monitored with a mass sensitive piezoelectric quartz crystal (quartz crystal nanobalance; QCN). In the presence of an inhibiting substance in the sample, the binding of cholinesterase to the immobilized inhibitor was reduced. The decrease of the rate of mass change was proportional to the concentration of free inhibitor in the sample. This way the affinity sensor followed anti-cholinesterase toxicity and the enzyme activity of ChE was not addressed. A assay for detection of organophosphates (OP) was optimized. Regeneration of the sensor surface was achieved with 1 mol L^–1 formic acid, which enabled 40 measurements with one sensor. All assays were carried out in a flow-through arrangement. The total measurement time (binding+regeneration) was 25 min and the detection limit for different OP (paraoxon, diisopropylfluorophosphate, chlorpyriphos, and chlorfenvinphos) was down to 10^–10 mol L^–1 (0.02 g L^–1). This sensor was used for determination of organophosphate (diisopropylfluorophosphate) levels in river water samples.Dedicated to the memory of Wilhelm Fresenius     

Multiresidue method using SPME for the determination of various pesticides with different volatility in confined atmospheres

An analytical method is described for assessing the vapour concentration of 11 pesticides (bioallethrin, chlorpyriphos methyl, folpet, malathion, procymidone, quintozene, chlorothalonil, fonofos, penconazole and trimethacarb) in confined atmospheres (e.g. a greenhouse after pesticide application). This study is a successful extension of a method previously developed by the authors for dichlorvos to much less volatile pesticides. Sampling was performed by using polydimethylsiloxane–solid phase micro-extraction (PDMS–SPME) fibres immersed in a 250-mL sampling flask through which air samples were dynamically pumped from the analysed atmosphere. After a 40-min sampling duration, samples were analysed by GC/MS.Calibration was performed from a vapour-saturated air sample. The linearity of the observed signal versus pesticide concentration in the vapour phase was proved from spiked liquid samples whose headspace concentrations were measured by using the proposed method. This procedure gave calibration curves with regression coefficients (R²) greater than 0.98, and the repeatability of these measurements was found with RSDs of 1.9–7.6%. As a field application test, this analysis procedure was used for the determination of gaseous procymidone concentrations as a function of time in the atmosphere of an experimental 8-m² and 20-m³ greenhouse. The pesticide was sprayed according to real cultivation conditions, and measurements were made for 80 h after application (8 measurements). The observed concentrations found ranged from 200 to 500 µg m^–3, thus indicating the level of contamination of the air breathed by people in such working conditions.Abbreviations GC/MS gas chromatography/mass spectrometry - SIM selective ion monitoring - FC43 perfluorotributylamine - RSD relative standard deviation - LOD limit of detection - LOQ limit of quantification     

Multidetermination of PCBs and pesticides by use of a dual GC column-dual detector system

Summary A new gas chromatographic method involving the use of two capillary columns, a switching valvue and electron capture-nitrogen-phosphorus detection, and allowing up to four retention characteristics per component to be obtained is reported.The proposed method was applied to the analysis for 123 compounds (13 PCBs and 110 pesticides), the determination limits and optimal measuring ranges of which are reported.The performance of the method was checked by analysis of certified standards and spiked samples, and was applied to the determination of the analytes in various water samples.     

Development and field evaluation of a new diffusive sampler for Hydrogen Sulphide in the ambient air

A diffusive sampler for the determination of hydrogen sulphide (H₂S) based on collection on a paper filter coated with silver nitrate followed by optical densitometric determination of the metal sulphide was developed. Laboratory tests were conducted in controlled atmosphere to evaluate linearity, uptake rate, face velocity effects, sample stability, influence of relative humidity and of interferents, precision and accuracy. The measured uptake rate for H₂S was determined in experiments involving sampling at different concentration levels in comparison to a wet standard colorimetric technique. The precision of the measurements for co-located passive samplers was lower than 15%. The accuracy of the data collected is within 20% of the actual value measured by the wet method. The sampler is capable of reliable measurements of H₂S at common levels of a polluted atmosphere in urban settings yielding average concentration levels over one month and beyond. Diffusive sampling can be adopted to analyse in detail the temporal and spatial trends of H₂S concentration in ambient air and in specific historic buildings or in museums. Figure At the end of sampling cap #2 is removed and optical density is measured     

Chemical characterization of selected metals by X-ray fluorescence method in particulate matter collected in the area of Krakow, Poland

This study presents the results of year long (2007–2008) particulate matter collecting campaigns. The three particle size fractions of particulate matter were collected in Krakow, Poland. Fine fraction consists of particles of a diameter below 2.5 µm, medium is between 2.5 and 8 µm and coarse fraction contains particles above 8 µm. Elemental concentrations were evaluated for each sample. Following elements were measured by EDXRF method: K, Ca, Ti, Cr, Mn, Fe, Cu, Zn, Br, and Pb. During each sampling campaign meteorological parameters such as temperature, wind speed, wind direction, humidity were taken from the same place. The highest values of mass particulate matter showed results from January 2008 and April 2008. These were about 14 µg/m³ for fine fraction, 8 µg/m³ for medium and 16 µg/m³ for coarse fraction. The lowest values were observed in May 2007, they were 4, 6, 6 µg/m³, respectively. During the winter season the wind speed was low and particulate matter remained in the air in high concentrations. In May 2007 the speed of wind was higher, reaching 2–3 m/s. PM was blown away from the city from the direction of N–W. Measured concentrations of elements were low, they were below permissible values specified by EU. The coarse fraction concentrations of Ca, Mn, and Fe were higher and characterized by the same trend. These samples were collected when the wind speed was low and its direction was from south-east. As concentrations of Cr, Cu, and Zn were low, these elements did not come from the south-east direction of Krakow. Concentration of Br correlates to the concentration of Pb. It suggests that they came from the same source (vehicles fuels burning).     

Assessment of the acute toxicity of triclosan and methyl triclosan in wastewater based on the bioluminescence inhibition of Vibrio fischeri

In this work, the contributions of triclosan and its metabolite methyl triclosan to the overall acute toxicity of wastewater were studied using Vibrio fischeri. The protocol used in this paper involved various steps. First, the aquatic toxicities of triclosan and methyl triclosan were determined for standard substances, and the 50% effective concentrations (EC₅₀) were determined for these compounds. Second, the toxic responses to different mixtures of triclosan, methyl triclosan, and surfactants were studied in different water matrices, i.e., Milli-Q water, groundwater and wastewater, in order to evaluate (i) the antagonistic or synergistic effects, and (ii) the influence of the water matrices. Finally, chemical analysis was used in conjunction with the toxicity results in order to assess the aquatic toxicities of triclosan and its derivative in wastewaters. In this study, the toxicities of 45 real samples corresponding to the influents and effluents from eight wastewater treatment works (WWTW) were analyzed. Thirty-one samples were from a wastewater treatment plant (WWTP) equipped with two pilot-scale membrane bioreactors (MBR), and the influent and the effluent samples after various treatments were characterized via different chromatographic approaches, including solid-phase extraction (SPE), liquid chromatography coupled to tandem mass spectrometry (LC–MS/MS), and SPE coupled to gas chromatography–mass spectrometry (GC–MS). The toxicity was determined by measuring the bioluminescence inhibition of Vibrio fischeri. In order to complete the study and to extrapolate the results to different WWTPs, the toxicity to V. fischeri of samples from seven more plants was analyzed, as were their triclosan and methyl triclosan concentrations. Good agreement was established between the overall toxicity values and concentrations of the biocides, indicating that triclosan is one of the major toxic organic pollutants currently found in domestic wastewaters.     

Evaluation of polyurethane foam, polypropylene, quartz fiber, and cellulose substrates for multi-element analysis of atmospheric particulate matter by ICP-MS

Traditional methods for the analysis of trace metals require particulate matter (PM) collected on specific filter substrates. In this paper, methods for elemental analysis of PM collected on substrates commonly used for organic analysis in air quality studies are developed. Polyurethane foam (PUF), polypropylene (PP), and quartz fiber (QF) substrates were first digested in a mixture of HNO₃/HCl/HF/H₂O₂ using a microwave digestion system and then analyzed for elements by inductively coupled plasma mass spectrometry. Filter blanks and recoveries for standard reference materials (SRMs) on these substrates were compared with a cellulose (CL) substrate, more commonly used for trace metal analysis in PM. The results show concentrations of filter blanks in the order of QF > PUF > PP > CL with a high variability in PUF and PP blanks relative to QF. Percent recovery of most elements from the SRMs on all substrates are within ±20% of certified or reference values. QF substrates showed consistent blanks with a reproducibility better than ±10% for the majority of elements. Therefore, QF substrates were applied to ambient PM collected in a variety of environments from pristine to polluted. Concentrations of field blanks for ≥18 of 31 elements analyzed on a small section of QF substrate are ≤25% of the amounts present in samples for urban atmospheres. Results suggest that QF used in a high-volume sampler can be a suitable substrate to quantify trace elements, in addition to organic species and hence reduce logistics and costs in air pollution studies.

On the determination of dynamic surface tensions by means of a modified bubble pressure method

A method for the determination of the dynamic surface tension of surfactant solutions is presented which allows to cover adsorption times down to 10 seconds. This method is based on the determination of the pressure inside two communicating bubbles. There is no deformation of the solution/air interface during the experimental procedure. Hence, in evaluating the kinetic data no surface area enlargement has to be taken into account. An automatically operating procedure should allow to cover adsorption times down to approximately one second and should improve the measuring accuracy substantially. Experimental investigations with aqueous n-decanoic acid solutions using the method proposed provided evidence that decanoic acid is adsorbed by a diffusioncontrolled mechanism.     

Double-layer Tedlar bags: a means to limit humidity evolution of air samples and to dry humid air samples

Tedlar bags, which are widely used to collect air samples, especially VOCs and odorous atmospheres, can allow humidity to diffuse when relative humidity levels differ between the inside and outside. Starting with dry air inside the bag and humid air outside, we monitored equilibrium times under several conditions showing the evolution and influence of collected volumes and exposed surfaces. A double-film Tedlar bag was made, to limit the impact of external humidity on a sample at low humidity level. With the addition of a drying agent between both films, the evolution of humidity of a sample can be stopped for several hours. When a VOC mixture was monitored in a humid atmosphere, humidity was decreased but no significant evolution of VOC concentrations was observed.     

Multiresidue analytical method of pesticides in peanut oil using low-temperature cleanup and dispersive solid phase extraction by GC-MS

A method for the determination of 33 pesticides in peanut oil by GC-MS was described. Two extraction procedures based on (i) low-temperature extraction and (ii) liquid-liquid extraction were tested for the optimization of the method. The mixture of anhydrous MgSO(4) with primary secondary amine (PSA) or with PSA and C(18) was performed as sorbents in dispersive SPE. Low temperature along with PSA and C(18) cleanup gave the best results. Pesticides were identified and quantified by GC-MS in SIM mode. The correlation coefficients, R(2), in the linear range tests were better than 0.990. The average recoveries for most pesticides (spiked at 0.02, 0.05, 0.2, and 1 mg/kg) ranged from 70 to 110%, the RSD was below 20% in most instances, and LODs varied from 0.5 to 8 mug/kg.     

Use of liquid chromatography quadrupole time-of-flight mass spectrometry in the elucidation of transformation products and metabolites of pesticides. Diazinon as a case study

Liquid chromatography (LC) coupled to hybrid quadrupole time-of-flight (QTOF) mass spectrometry (MS) is a useful analytical tool in the elucidation and confirmation of transformation products (TPs)/metabolites of pesticides with a wide range of polarity, in both environmental and biological samples. Firstly, the versatility of LC allows the determination of very distinct TPs/metabolites as chromatographic conditions can be easily changed and optimized depending on the analytical problem. Secondly, the mass accuracy provided by the TOF analyser allows the assignment of a highly probable empirical formula for each compound and the differentiation between nominal isobaric compounds. Finally, the possibility of performing MS/MS spectra with accurate mass measurements can been used for the final characterization of the TPs/metabolites detected and for the differentiation of isomeric compounds. In this study, the insecticide diazinon was used as model compound, and its photodegradation and metabolism have been investigated by LC-QTOF-MS. On one hand, environmental spiked water was irradiated with a mercury lamp for 9 days, sampling 3-mL aliquots approximately every 12 h. On the other hand, both in vitro and in vivo metabolism experiments were carried out with different substrate concentrations and incubation times. After centrifugation, and protein precipitation in the in vitro and in vivo studies, 50-μL aliquots of both environmental and biological samples were directly injected into the LC electrospray ionization QTOF system. The most important transformation processes were found to be hydrolysis of the ester moiety, hydroxylation in the aromatic ring or in one of the alkylic groups, oxidation of the sulfur atom on the P=S cleavage or a combination of these processes, with the highest number of compounds being found in the photodegradation study. Very polar compounds, such as diethyl phosphate and diethyl thiophosphate, were detected after direct injection of the aqueous sample, which was feasible owing to the characteristics of the LC. In MS mode, mass errors were below 3 mDa, leading to an empirical formula for each compound. MS/MS spectra with accurate mass were used for the final elucidation of the compounds detected.     

Development of a gas chromatography-mass spectrometry method for the determination of pesticides in gaseous and particulate phases in the atmosphere

A reliable multi-residue method for determining gaseous and particulate phase pesticides in atmospheric samples has been developed. This method, based on full scan gas chromatography–mass spectrometry (GC–MS), allowed the proper determination of sixteen relevant pesticides, in a wide range of concentrations and without the influence of interferences. The pesticides were benfluralin, bitertanol, buprofezin, chlorfenvinphos, chlorpyrifos, chlorpyrifos-methyl, ethalfluralin, fenthion, lindane, malathion, methidathion, propachlor, propanil, pyriproxifen, tebuconazol and trifluralin. Comparisons of two types of sampling filters (quartz and glass fibre) and four types of solid-phase cartridges (XAD-2, XAD-4, Florisil and Orbo-49P) showed that the most suitable supports were glass fibre filter for particulate pesticides and XAD-2 and XAD-4 cartridges for gaseous pesticides (>95% recovery). Evaluations of elution solvents for ultrasonic-assisted extraction demonstrated that isooctane is better than ethylacetate, dichloromethane, methanol or a mixture of acetone:hexane (1:1).Recovery assays and the standard addition method were performed to validate the proposed methodology. Moreover, large simulator chamber experiments allowed the best study of the gas-particle partitioning of pesticides for testing the sampling efficiency for the validation of an analytical multiresidue method for pesticides in air. Satisfactory analytical parameters were obtained, with a repeatability of 5 ± 1%, a reproducibility of 13 ± 3% and detection limits of 0.05–0.18 pg m⁻³ for the particulate phase and 26–88 pg m⁻³ for the gaseous phase. Finally, the methodology was successfully applied to rural and agricultural samples in the Mediterranean area.     

Comparison of pesticides levels in grape skin and in the whole grape by a new liquid chromatographic multiresidue methodology

The increasing interest in the study of pesticides in grapes is justified from an enological point of view, since some pesticides can interfere with fermentative microflora used in wine production, as well as, with the consumer’ safety. Considering that washing grapes before consumption is the standard procedure, the study of the effect of washing on the residue concentration is required to assess real consumer exposure. In this work, pesticide mobility in grapes was studied, by comparing their residual concentration in the skin with that of the whole grape. The efficiency of water washing to remove pesticides from grape skins was also evaluated.One variety of grapes from the Northern region of Portugal, Trajadura, sampled at two maturation periods of the 2001 crop, were analysed by a new validated methodology involving liquid chromatography with diode array detection.It was concluded that, although there were no significant differences between some pesticide levels found in the whole grape (skin and pulp) and in the grape skin, pyrimethanil was preferably found in the pulp, while metalaxyl was detected in the skin but not in the whole grape.The removal of pesticides from grapes by washing did not exceed 70% (procymidone). Never the less, it was concluded that consumer intake of the pesticides from grapes studied in this work should be significantly decreased as a result of water washing of the grapes.The concentration levels found for the pesticide residues were below both the Portuguese and the FAO Maximum Residue Levels (MRLs), thus causing no problems in terms of food safety.     

Pesticides and degradation products in groundwaters from a vineyard region: Optimization of a multiresidue method based on SPE and GC‐MS

A reliable multiresidue method based on solid phase extraction was developed using GC–MS to determine and quantify 34 pesticides, including herbicides, fungicides, insecticides, and some of their degradation products, in groundwater in a vineyard region of La Rioja (northern Spain). Different parameters were optimized and good recoveries (65–108% range) and precisions (12–19% range) were achieved with spiked water samples for a concentration of 0.1 μg/L. The experimental results showed an excellent linearity (r² > 0.99) over the 0.1–1.5 μg/L range. The detection limits of the proposed method were 1–37 ng/L for most of the compounds studied. The methodology has been successfully applied to the analysis of groundwater samples from vineyard areas in La Rioja and the presence of pesticides, especially fungicides and herbicides, at several concentration levels was revealed. Terbuthylazine, its metabolite desethyl‐terbuthylazine, and fluometuron were the pesticides most frequently detected in higher concentrations. Overall and taking into consideration the European Union maximum residue limit of pesticides in groundwater, 16 of the 34 compounds included in this study were detected in concentrations over that limit in at least one of the samples analyzed.     

环境样品中痕量甲醛的催化荧光动力学分析

基于在硫酸介质中, 痕量甲醛能促进溴酸钾氧化吡咯红并使其荧光强度减弱的反应, 建立了动力学荧光法分析测定痕量甲醛的新方法. 研究了温度、时间, 各种试剂浓度等条件对测定的影响. 在最佳实验条件下, 方法的线性范围是8～200 ng/mL, 检出限为6.1 ng/mL. 该方法用于环境水样、室内空气、食品中痕量甲醛的测定, 并与乙酰丙酮分光光度法进行了对照, 结果无显著性差异.     

Analysis of selected pesticides and alkylphenols in human cord blood by gas chromatograph-mass spectrometer

A total of seven pesticides and eight alkylphenols were monitored using this method for the determination of their trace levels in human cord blood. The pesticides are lindane, diazinon, α-endosulfan, β-endosulfan, endosulfan sulfate, chlorpyrifos and endrin; while the alkylphenols are 4-n-butylphenol, 4-n-pentylphenol, 4-n-hexylphenol, 4-t-octylphenol, 4-n-heptylphenol, nonylphenol, 4-n-octylphenol and bisphenol A. The pesticides and alkylphenols in the cord blood samples were extracted with solid phase extraction IST C18 cartridges and analyzed by selected ion monitoring mode using quadrapole detector in Shimadzu QP-5000 gas chromatograph-mass spectrometer. Trace levels of pesticide and alkylphenols in the range of non-detectable to 15.17 ng ml⁻¹, were detected in the human cord blood samples. This technique of monitoring the levels of endocrine-disruptors in blood samples is consistent, reliable and cost effective while reducing wastage of time and solvents.     

Evolution of anthropogenic aerosols in the coastal town of Salina Cruz,Mexico: part III size-segregated elemental composition analysed by total-reflection X-ray fluorescence spectrometry

Heavy metals in various size modes of the atmospheric aerosol are a concern for human health. Their and other elements’ concentrations are indicative for anthropogenic and natural aerosol sources. Si, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Br, Rb, Sr, Hg, and Pb were determined as a complementary contribution to a study on aerosol cycling during the wet season, June 2004, in a humid, subtropical climate, i.e. in the city of Salina Cruz, situated on the Pacific coast of the Isthmus of Tehuantepec (16.2°N, 95.2°W), Mexico. For mass (gravimetry) and elemental analyses, particles were collected by a Berner low-pressure round nozzle cascade impactor using four stages corresponding to 0.1–0.25, 0.25–1.0, 1.0–4.0, and 4–16?µm of aerodynamic particle size. The impaction plates were modified such that approx. 1/6 consisted of a plastic support (Persplex®) for total reflection X-ray fluorescence spectrometry (TXRF). The elements’ total content was determined by TXRF without any further sample pretreatment. Limits of quantification (LOQ) for elemental content in individual impactor stages corresponded to 25–60?ng?m^?3 for Si; 0.8–4?ng?m^?3 for Cl, K, Ca, Ti, and V; 3–20?pg?m^?3 for Cr, Mn, Fe, Cu, Ni, and Zn; and 7–50?pg?m^?3 for As, Se, Br, Rb, Sr, Hg, and Pb. In some samples, however, high blank values for the supports gave an LOQ?=?6–19?ng?m^?3 for Cl; 3--7?ng?m^?3 for Ca; 3–7?ng?m^?3 for Fe, Ni, Cu, and Zn; and 60–70?ng?m^?3 for Pb. The influence of local natural, industrial, and vehicle traffic sources for heavy-metal mobilization was obvious. Heavy-metal abundances did not coincide with regionally distributed pollutants. V and Ni were found at particularly elevated levels advected with the sea breeze, which points to ships as sources. Br and Pb were found at particularly low levels. The concentrations of Br, Rb, Sr, and Pb were found below LOQ at least in some, As, Co, Se, and Hg in all of the samples. The elements’ characteristic differences in mass size distributions were obvious despite the coarse size resolution. During the cycling of air masses from land to sea and back again, enrichment of super-micrometre particles in the near ground aerosol was observed under dry weather conditions. Rain preferentially removed the large particles with which heavy metals have been associated.     

Validation of a qualitative screening method for pesticides in fruits and vegetables by gas chromatography quadrupole-time of flight mass spectrometry with atmospheric pressure chemical ionization

A wide-scope screening method was developed for the detection of pesticides in fruit and vegetables. The method was based on gas chromatography coupled to a hybrid quadrupole time-of-flight mass spectrometer with an atmospheric pressure chemical ionization source (GC-(APCI)QTOF MS). A non-target acquisition was performed through two alternating scan events: one at low collision energy and another at a higher collision energy ramp (MS^E). In this way, both protonated molecule and/or molecular ion together with fragment ions were obtained in a single run. Validation was performed according to SANCO/12571/2013 by analysing 20 samples (10 different commodities in duplicate), fortified with a test set of 132 pesticides at 0.01, 0.05 and 0.20 mg kg⁻¹. For screening, the detection was based on one diagnostic ion (in most cases the protonated molecule). Overall, at the 0.01 mg kg⁻¹ level, 89% of the 2620 fortifications made were detected. The screening detection limit for individual pesticides was 0.01 mg kg⁻¹ for 77% of the pesticides investigated. The possibilities for identification according to the SANCO criteria, requiring two ions with a mass accuracy ≤±5 ppm and an ion-ratio deviation ≤±30%, were investigated. At the 0.01 mg kg⁻¹ level, identification was possible for 70% of the pesticides detected during screening. This increased to 87% and 93% at the 0.05 and 0.20 mg kg⁻¹ level, respectively. Insufficient sensitivity for the second ion was the main reason for the inability to identify detected pesticides, followed by deviations in mass accuracy and ion ratios.