Temperature-dependent magnetic moment in the MnAs-CrAs system

Magnetic susceptibilities have been measured for the mixed compounds Mn_1−xCr_xAs (0≤x≤1) and the compound MnP in the temperature region up to 1400 K. The _X¹_g vs. T curves of Mn_1−xCr_xAs follow the Curie-Weiss law only in the temperature region where the crystal structure is of the B8₁ type. Some important problems are pointed out from the data.     

Magnetic properties of the intermetallic compounds Gd(Mn1−xNix)2

The magnetic properties of pseudobinary compounds Gd(Mn_1−xNi_x)₂ were studied to understand the type of magnetic interaction among the constituent atoms of the parent binary compound. The Arrott plot for GdMn₂ indicates no spontaneous magnetization. The magnetization and the Curie temperature increase with increasing concentration of Ni on the Mn rich side. The collapse of the Mn moment makes the Gd moment dominant in magnetization with increasing Ni concentration.     

Structure, oxygen stoichiometry and electrical conductivity in the system Sr-Ce-Co-O

Mixed oxides in the system S-Ce-Co-O were prepared by solid state reaction and by freeze-drying of precursor compounds followed by thermal treatment. Two types of perovskite oxides exist in the system: Solid solutions of the type Sr_{1 − y}Ce_yCoO_{3 − x} and mixed oxides of the type (1 − y)SrCeO₃ − ySrCoO_{3 − x}. Microstructures and phase compositions were determined by electron microscopy and X-ray diffraction. SrCoO_{3 − x} forms a solid solution of ceria on the A-site in the strontium cobaltite lattice up to 0.15 mol Ce. This solid solution corresponds to the high-temperature structure of pure SrCoO_{3 − x} and is characterized by high oxygen exchange and electrical conductivity. The oxygen deficiency x was measured by solid electrolyte coulometry. The oxygen deficiency of solid solutions Sr_{1 − y}Ce_yCoO_{3 − x} increases with temperature and decreases with pO₂ in the ambient atmosphere and with increasing Ce dopant concentration. The pO₂-T-x diagram of the solid solution was determined. The T, pO₂ and dopant concentration dependencies of electrical conductivity were measured by a four-point d.c. technique. By Ce doping strontium cobaltite becomes a stabilized high-conductive material (maximum conductivity: 500 S cm⁻¹ at 400 °C, E_a = 0.025 eV, p-type). Above this temperature the T-coefficient of the conductivity changes from positive (semiconducting) to negative values.     

Magnetic and Magneto-optical properties of Heusler alloys of the type Ni3-xMnxSn

The crystallographic, magnetic and magneto-optical properties of Heusler compounds of the type Ni_3-xMn_xSn were investigated. The thermal expansion behaviour of a limited number of these compounds was also studied. The cubic L2₁ structure was found to exist in the range 0.6 x 2.2. With increasing x the saturation moment first increases, then decreases again. The main peak in the Kerr rotation spectra measured in the energy range 0.5-4.5 eV shows a similar trend. The Curie temperature and the lattice constant increase with x, both quantities showing a discontinuity near x = 1. All these features are discussed in terms of relative site occupancies of the Mn atoms at the tetrahedral and octahedral sites in the L2₁ structure.     

Zero-field current-voltage characteristics in high-temperature superconductors

We have observed the anomalous magnetization of Bi₂Sr₂CaCu_2−xNi_xO₈ (x = 0 and 0.02) single crystals. Anisotropy decreases with iodine intercalation although it expands the space between CuO₂ layers. Iodine intercalation seems to suppress the magnetization anomaly for Ni = 1% crystals, but not for Ni = 1% substituted crystals. We have discussed these results in terms of the increase of anisotropy by Ni substitution and the dimensional crossover of flux lines. Effects of both oxygen concentration and substitution of a magnetic element for the Cu site on the anisotropy of Bi₂Sr₂CaCu₂O₈ crystals show the same tendency as the case of the YBa₂Cu₃O₇ superconductor.     

Lithium insertion to ReO3-type metastable phase in the Nb2O5–WO3 system

Lithium insertion to distorted ReO₃-type metastable solid solution Nb_xW_1−xO_3−x/2 (0≤x<0.25) has been studied by chemical and electrochemical methods. In the course of lithium insertion into tetragonal compounds, transition to a cubic phase was found to occur in the region where values of y (in Li_yNb_xW_1−xO_3−x/2) fall between 0.2 and 0.3, and the phase transition was found to depend on the conditions of the reaction. Changes in OCV and lattice parameters in tetragonal region (y<0.2) were discussed from the viewpoint of the ordering of lithium ions. Also, the component diffusion coefficient of lithium in tetragonal compounds Li_0.1Nb_xW_1−xO_3−x/2 (0≤x≤0.23) was found to increase with niobium content when x≤0.10, and to saturate at 4×10⁻⁹ cm²/s.     

The effect of rare earth substitution on the magnetic properties of Ni0.5Zn0.5MxFe2−xO4 (M: rare earth)

Variation of the complex permeability with frequency of Ni_1−xZn_xFe₂O₄ (x=0.5, 0.6 and 0.7) prepared by a combustion method has been measured over a wide range of frequency, up to 1.8 GHz. Zn content improves permeability but moves the onset of resonance to lower frequencies.

The influence on some properties of samples prepared by the insertion of small amounts of Ruthenium, Yttrium and rare-earth cations into the Ni_0.5Zn_0.5M_xFe_2−xO₄ ferrite has been also investigated. Relative losses and Curie temperature of all the samples have been measured. Ferrites substituted with Ru and Gd improve microwave behavior compared to non-substituted samples.     

Mixed electronic and ionic conductivity of LaCo(M)O3 (M=Ga, Cr, Fe or Ni).: V. Oxygen permeability of Mg-doped La(Ga, Co)O3−δ perovskites

The LaGa_1−x−yCo_xMg_yO_3−δ solid solutions with rhombohedrally-distorted perovskite structure were ascertained to form in the concentration range of 0≤y≤0.10 at x=0.60 and 0≤y≤0.20 at x=0.35–0.40. Increasing cobalt content results in increasing electrical conductivity and thermal expansion of the perovskites. Thermal expansion coefficients of the LaGa_1−x−yCo_xMg_yO_3−δ ceramics were calculated from the dilatometric data to vary in the range of 12.4–19.8×10⁻⁶ K⁻¹ at 300–1100 K. Doping La(Ga,Co)O_3−δ solid solutions with magnesium leads to increasing oxygen nonstoichiometry, electronic and oxygen ionic conductivity. Oxygen permeation fluxes through LaGa_1−x−yCo_xMg_yO_3−δ membranes were found to be limited by the bulk ionic conduction and to increase with magnesium concentration, being essentially independent of cobalt content.     

Erbium in silicon–germanium quantum wells

Strained Si_1−xGe_x/Si quantum wells have been doped with erbium by implantation. A comparison is made with strained Si_1−xGe_x/Si quantum wells and relaxed Si_1−xGe_x, with x between 10% and 25%, doped with erbium during MBE growth. The erbium concentration was between 1×10¹⁸ and 5×10¹⁸ cm⁻³ throughout the active regions. Transmission electron microscopy, X-ray diffraction, and photoluminescence studies indicate that good regrowth can been achieved after full amorphisation by implantation of the strained quantum wells. The erbium luminescence is more intense in the Si_1−xGe_x/Si layers, but erbium-implanted samples containing Si_1−xGe_x exhibit defect luminescence in the region of 0.9–1.0 eV. These defects are also present when Si_1−xGe_x/Si quantum wells are implanted with an amorphising dose of silicon, and then regrown. They are attributed to small germanium-rich platelets, rather than to erbium-related defects. Electroluminescence is presented from a forward biased erbium-implanted Si_0.87Ge_0.13/Si structure at a drive current density of only 1.8 mA/cm².     

Nax/2Bi1−x/2MoxV1−xO4 and Bi1−x/3MoxV1−xO4 New Scheelite-related phases

New Scheelite-related solid solutions of the compositions Na_x/2Bi_1−x/2Mo_xV_1−xO₄ (0≤x≤1) and Bi_1−x/3 Mo_xV_1−xO₄(0≤x≤0.2) have been synthesised by the substitution of Na and Mo at the A and B sites respectively of the ABO₄ type ferroelastic BiVO₄. The phases were characterised using chemical analysis, powder X-ray diffraction, scanning electron microscopy, EDAX, and Raman spectroscopy. While almost a continuous solid solution is obtained for the series Na_x/2Bi_1−x/2Mo_xV_1−xO₄, the absence of Na at the A-site results only in a narrow stability region for the other series, Bi_1−x/3 Mo_xV_1−xO₄ where 0≤x≤0.2. Raman spectra of selected samples at room temperature also suggest that vanadium and molybdenum atoms are disordered at the tetrahedral sites.     

Material design of new lithium ionic conductor, thio-LISICON, in the Li2S–P2S5 system

A new lithium ionic conductor of the thio-LISICON (LIthium SuperIonic CONductor) family was found in the binary Li₂S–P₂S₅ system; the new solid solution with the composition range 0.0≤x≤0.27 in Li_3+5xP_1−xS₄ was synthesized at 700 °C and characterized by X-ray diffraction measurements. Its electrical and electrochemical properties were studied by ac impedance and cyclic voltammetry measurements, respectively. The solid solution member at x=0.065 in Li_3+5xP_1−xS₄ showed the highest conductivity value of 1.5×10⁻⁴ S cm⁻¹ at 27 °C with negligible electronic conductivity and the activation energy of 22 kJ mol⁻¹ which is characteristic of high ionic conduction state. The extra lithium ions in Li₃PS₄ created by partial substitution of P⁵⁺ for Li⁺ led to the large increase in ionic conductivity. In the solid solution range examined, the minimum conductivity was obtained for the compositions, Li₃PS₄ (x=0.0 in Li_3+5xP_1−xS₄) and Li₄P_0.8S₄ (x=0.2 in Li_3+5xP_1−xS₄); this conductivity behavior is similar to other thio-LISICON family with the general formula, Li_xM_1−yM_y′S₄ (M=Si, Ge, and M′=P, Al, Zn, Ga, Sb). Conduction mechanism and the material design concepts are discussed based on the conduction behavior and the structure considerations.     

Synthesis and electrophysical properties of novel lithium ion conducting oxides

Novel lithium ion conducting oxides with perovskite structure have been synthesized and studied. It has been found that the La_2/3−xLi_3xTiO₃ and La_2/3−xLi_3xNb₂O₆ compounds have a perovskite structure at 1/24 < x < 1/6 and 0 < x < 3/10, respectively. The results of investigating the electrical properties of both groups of perovskites indicate a high lithium ion conductivity.     

Hyperfine investigations of the magnetic state in ordered Pt3−xFe1+x

Mössbauer effect studies of Pt_3−xFe_1+x fcc ordered alloys in the range 4.2 K <T<300 K, in zero and in external magnetic field, for samples with x = 0.16 to 0.28, are reported. The low-temperature spectra show several satellite lines which are related to different excess-Fe nearest-neighbor configurations. Experiments in external fields give information on the different local spin structure at different concentrations.     

Oxygen permeability of La2Cu(Co)O4+δ solid solutions

Formation of the La₂Cu_1−xCo_xO_4+δ solid solutions with orthorhombic K₂NiF₄-type structure was found to be in the range of 0≤x≤0.30 at temperatures above 1270 K. Incorporating cobalt into the copper sublattice of lanthanum cuprate leads to increasing oxygen hyperstoichiometry and decreasing electrical conductivity. Thermal expansion coefficients of the La₂Cu_1−xCo_xO_4+δ (x=0.02–0.30) ceramics at 470–1100 K were calculated from the dilatometric data to vary in the range (12.2–13.2)×10⁻⁶ K⁻¹. Studying the dependence of oxygen permeation fluxes through La₂Cu(Co)O_4+δ on the membrane thickness demonstrated that the oxygen transport at the thickness values below 1 mm is limited by both surface exchange rate and bulk ionic conductivity. Oxygen permeability of the La₂Cu_1−xCo_xO_4+δ solid solutions was ascertained to increase with cobalt concentration at x=0.02–0.10 and to decrease with further dopant additions, indicating a participation of interstitial oxygen in the ionic transport.     

Properties of nonstoichiometric Pr0.6−xSr0.4MnO3 as the cathodes of SOFCs

A series of samples Pr_0.6−xSr_0.4MnO₃ (x=0, 0.01, 0.05, 0.1, 0.15, 0.2) were synthesized by a solid state reaction method. Pr deficiency at the A site has a great effect on the properties of Pr_0.6−xSr_0.4MnO₃ as the cathode of SOFCs (solid oxide fuel cells). Compared to the commonly used La_0.6Sr_0.4MnO₃ and La_0.55Sr_0.4MnO₃ cathode, Pr_0.6−xSr_0.4MnO₃ is better in the properties of conductivity, overpotential and impedance. In all the samples, the one with x=0.05, Pr_0.55Sr_0.4MnO₃, revealed the best performance in the measured temperature range.     

Magnetic susceptibility, electrical resistivity and thermal expansion coefficient of NiAs-type V1−xCrxSe

V_1−xCr_xSe(0.05x0.83) shows a temperature dependence of the magnetic susceptibility χ which is similar to that of CrSe. At small x, the magnetic transition temperature T_t(x) and the Weiss constant θ_p(x) decrease with decreasing x, while the effective number of Bohr magnetons per Cr (P_eff) significantly increases.     

Defect structure of quenched γ-BICOVOX by combined X-ray and neutron powder diffraction

A detailed investigation of the defect structure of the Co doped BIMEVOX solid electrolyte, Bi₂V_{1 − x}Co_xO_{5.5 − 3x/2} (x = 0.1 and x = 0.2), quenched from high temperature, has been carried out using X-ray and neutron powder diffraction data measured at room temperature. The structure is built up from alternating layers of [Bi₂O₂]_n²ⁿ⁺ and [V_{1 − x}Co_xO_{3.5 − 3x/2}]_n²ⁿ⁻ with disorder limited to the vanadate layer. The ideal V/Co co-ordination is octahedral with corner sharing of equatorial oxygens. The refinements show that the true structure is distorted, with disorder in both apical and equatorial oxygens and oxygen vacancies concentrated in the equatorial positions. Detailed analysis of the oxygen site occupancies reveals two main types of V/Co co-ordination viz. distorted octahedral and distorted tetrahedral. The majority of the sites in both compositions are tetrahedral.     

Determination of different oxygen transport mechanisms and measurement of the oxygen ion conductivity of Y1Ba2Cu3O7−x

By undertaking AC electrochemical impedance experiments on yttria stabilised zirconia electrolytes with polished Y₁Ba₂Cu₃O_7−x electrodes, the activation energy for oxygen ion transport within the bulk of Y₁Ba₂Cu₃O_7−x, in air, over the temperature range 823 K–1043 K, was determined to be 1.50 ± 0.05 eV. At 1000 K the oxygen ionic conductivity was calculated to be around one order of magnitude lower than that in yttria stabilised zirconia. Typical calculated values were σ=5×10⁻⁵ (ω cm)⁻¹ and 6×10⁻³ (ω cm)⁻¹ at the respective temperatures 823 K and 1043 K. By employing a similar cell but with Y₁Ba₂Cu₃O_7−x paste electrodes, oxygen transfer between the Y₁Ba₂Cu₃O_7−x and the electrolyte was found to occur via a surface diffusional processes. Over the temperature range 873 K–1098 K, in air, the activation energy for in-diffusion at the surface was found to be 1.4±0.1 eV and that for out-diffusion at the surface to be 1.76±0.05 eV.     

Oxygen diffusion and surface exchange in La1−xSrxFe0.8Cr0.2O3−δ (x=0.2, 0.4 and 0.6)

Oxygen tracer diffusion (D*) and surface exchange rate constant (k*) have been measured, using isotopic exchange and depth profiling by secondary ion mass spectrometry (SIMS), in La_1−xSr_xFe_0.8Cr_0.2O_3−δ (x=0.2, 0.4 and 0.6). Measurements were made as a function of temperature (700–1000 °C) and oxygen partial pressure (0.21–10⁻²¹ atm) in dry oxygen, water vapour and water vapour/hydrogen/nitrogen mixtures. At high oxygen activity, D* was found to increase with increasing temperature and Sr content. The activation energies for D* in air are 2.13 eV (x=0.2), 1.53 eV (x=0.4) and 1.21 eV (x=0.6). As the oxygen activity decreases, D* increases as expected qualitatively from the increase in oxygen vacancy concentration. Under strongly reducing conditions, the measured values of D* at 1000 °C range from 10⁻⁸ cm² s⁻¹ for x=0.2 to 10⁻⁷ cm² s⁻¹ for x=0.4 and 0.6. The activation energies determined at constant H₂O/H₂ ratio are 1.21 eV (x=0.2), 1.59 eV (x=0.4) and 0.82 eV (x=0.6).

The surface exchange rate constant of oxygen for the H₂O molecule is similar in magnitude to that for the O₂ molecule and both increase with increasing Sr concentration.     

High field magnetization of the Laves phase compounds M(Co1−xAlx)2 (M = Y, Lu)

Magnetization measurements have been carried out on the Laves phase compounds M(Co_1−xAl_x)₂(M = Y, Lu) up to 42 T. Sharp metamagnetic transitions with small hysteresis are found in Y(Co_1−xAl_x)₂, while broad transitions with large hysteresis are found in Lu(Co_1−xAl_x)₂. The results suggest that the former compounds are magnetically homogeneous but the latter inhomogenous.