Nitrogen and hydrogen as carrier and make-up gases for GC-MS with Cold EI

Gas chromatography–mass spectrometry (GC-MS) with Cold EI is based on interfacing GC and MS with a supersonic molecular beam (SMB) and sample compounds ionization with a fly-through ion source as vibrationally cold compounds in the SMB (hence the name Cold EI). We explored the use of nitrogen and hydrogen as carrier and make-up gases with Cold EI and found:

1. Nitrogen is very effective in cooling compounds in SMB and while helium requires 60 ml/min nitrogen provides effective cooling with only 7–8 ml/min combined column and make-up flow rate. Hydrogen is less effective than helium and requires higher flow rates.
2. The transition from helium to nitrogen (or hydrogen) is simple and fast and requires just closing the helium valve and opening the nitrogen valve.
3. The same column used with helium can be used with nitrogen or hydrogen.
4. The same elution times could be obtained with nitrogen or hydrogen as with helium.
5. The GC separation with nitrogen was reduced compared with helium and peak widths were increased by an average factor of 1.5 for similar elution times. Hydrogen provided ~0.7 narrower peak widths than helium.
6. The signal with nitrogen was reduced compared with helium by an average factor of 3.3 and the signal loss was reduced with higher compounds mass. With hydrogen the signal loss was about a factor of 1.5 but the baseline noise was higher thus with similar S/N as with nitrogen.
7. USEPA 8270 semivolatile mixture was easily analyzed with both nitrogen and hydrogen carrier gases.

     

Determination of rotenone in river water utilizing packed capillary column switching liquid chromatography with UV and time-of-flight mass spectrometric detection

Fast and sensitive packed capillary column switching liquid chromatography methodology has been developed for the determination of the pesticide rotenone in river water. Sample volumes of up to 1 ml are loaded onto a 23 x 0.25 mm, 5 microm Kromasil C18 packed capillary precolumn using a noneluting solvent composition of water-acetonitrile (99:1, v/v) at flow-rates up to 100 microl/min prior to solute backflushing onto a 200 x 0.32 mm, 3.5 microm Kromasil C18 packed capillary analytical column using a mobile phase of water-acetonitrile (30:70, v/v) at a flow-rate of 5 microl/min. The method was evaluated using river water samples spiked with rotenone in the concentration range 0.5-50 ng/ml using UV detection. The within-assay precision was between 5.0 and 7.7% relative standard deviation (RSD, n = 6) and the between assay precision was between 7.5 and 8.9% RSD (n = 6). The method was linear within the investigated mass range displaying a calibration curve correlation factor of 0.997. The mass limit of detection was 10 pg corresponding to a concentration limit of detection of 10 pg/ml, using time-of-flight mass spectrometry.     

Gas Chromatographic Separation of Carbonyl Compounds as Their 2,4-dinitrophenylhydrazones Using Glass Capillary Columns

The gas chromatographic separation of 22 carbonyl compounds as their 2,4-dinitrophenylhydrazones was investigated using glass capillary columns. Complete separation of the 2,4-dinitrophenylhydrazones of ten aliphatic aldehydes, eight aliphatic ketones and four aromatic aldehydes was obtained, except for the derivatives of n-valeraldehyde and isobutyl methyl ketone, whose peaks overlapped, and the o- and m-tolualdehyde derivatives, which were poorly separated. The optimum conditions were as follows: stationary phase, SF-96; column size, 20 m × 0.25 mm I.D. ; column temperature, 200-240°; injection and detector temperatures, 280-290°; carrier gas flow-rate, helium 1.0-1.2 ml/min or nitrogen 1.1-1.2 ml/min. The method was applied to the analysis of aliphatic carbonyl compounds in car exhaust fumes and cigarette smoke.     

Miniaturization of capillary electrochromatography using an ultrashort capillary column

The instrumentation for miniaturization of capillary electrochromatography was devised and an injection method for this apparatus was proposed. By using an ultra short capillary column (15 mm packed length, 36 mm total length, 75 microm inner diameter, packed with cation exchange supports), the separation of five biochemical compounds was performed within 1 min. The high separation efficiency of 9780 plates was achieved by using an ultrashort capillary column. The miniaturized instrumentation for capillary electrochromatography might be utilized as one of the possible methods in microfabricated analysis or in an alternative approach to it.     

Fast analysis of nicotine related alkaloids in tobacco and cigarette smoke by megabore capillary gas chromatography

A novel fast megabore capillary gas chromatographic (MCGC) method for analysis of 7 nicotine related alkaloids in tobacco and cigarette smoke, including nicotine, nornicotine, myosmine, nicotyrine, anabasine, anatabine and 2,3-dipyridyl, was developed. The use of megabore capillary column GC methodology, equipped with flame ionization detector (FID), provided rapid, unambiguous nicotine related alkaloids analysis. One gram flue-cured tobacco (or Cambridge filter pad), 20 ml ether, and 5 ml 10% sodium hydroxide solution, added with n-heptadecane as the internal standard, were placed in a flask, and the flask was capped and placed in an ultrasonic bath for 15 min. A 1 microl volume was analyzed by capillary GC operating in split-injection mode on a mega bore Simplicity-5 column. This simple procedure was compared with the previously reported packed column GC method and the Griffith still-colorimetric method. The application of the method for analysis of various flue-cured tobaccos and cigarette smoke was discussed.     

Determination of 1-(2-methoxyphenyl)piperazine derivatives of isocyanates at low concentrations by temperature-programmed miniaturized liquid chromatography

A temperature-programmed packed capillary LC method with large-volume injection on-column focusing has been developed for screening and determination of 1-(2-methoxyphenyl)piperazine derivatives of airborne toluene-2,4-diisocyanate, toluene-2,6-diisocyanate, hexamethylenediisocyanate and methylenebisphenyl-4,4-diisocyanate, based on sampling methods described in MDHS 25/3. Injection volumes up to 100 microl were successfully loaded onto the 250x0.32 mm I.D. capillary column packed with 3 microm Hypersil ODS particles. The isocyanate derivatives were loaded at 10 degrees C and eluted by a three-step temperature program starting at 10 degrees C for 10 min, followed by a temperature ramp of 2.5 degrees C min(-1) to 45 degrees C and then 9.9 degrees C min(-1) to 90 degrees C. The mobile phase consisted of acetonitrile-acetate buffer (3% triethylamine, pH 4.5) (45:55, v/v). The isocyanate derivatives were dissolved in acetonitrile-acetate buffer (3% triethylamine, pH 4.5) (30:70, v/v) to achieve sufficient focusing. The concentration limit of detection of the individual derivatives utilizing an "U" shaped flow cell with a 8.0 mm light path and an injection volume of 100 microl was 44, 87, 43 and 210 pg ml(-1) for toluene-2,6-diisocyanate, hexamethylenediisocyanate, toluene-2,4-diisocyanate and methylenebisphenyl-4,4-diisocyanate, respectively. Within the investigated concentration range, 10-500 ng ml(-1), the linear calibration curves gave correlation coefficients ranging from 0.994 to 0.998. The repeatability of the method with regard to retention time and peak height ranged from 0.3 to 1.1% and 1.1 to 2.3% (n=9) relative standard deviation, respectively. The average recovery of the method, with regard to toluene-2,4-diisocyanate, was 97.7+/-1.6% (n=9).     

Wet effluent parallel plate diffusion denuder coupled capillary ion chromatograph for the determination of atmospheric trace gases

We describe an inexpensive, compact parallel plate diffusion denuder coupled capillary IC system for the determination of soluble ionogenic atmospheric trace gases. The active sampling area (0.6x10 cm) of the denuder is formed in a novel manner by thermally bonding silica gel particles to the surface of Plexiglas plates. The effluent liquid from the parallel plate diffusion denuder is collected and preconcentrated on a capillary preconcentrator column before analysis using a capillary ion chromatograph. Using SO(2) as the test gas, collection efficiency is essentially quantitative at air sampling rates up to 500 ml min(-1). The system provides a limit of detection (LOD) of 1.6 parts per trillion for SO(2) for a 10 min sampling period.     

Influence of the carrier gas on retention factors of gaseous hydrocarbons on polytrimethylsilylpropyne using capillary gas chromatography

The retention factor and height equivalent of a theoretical plate for gaseous hydrocarbons C₁—C₄ were studied on capillary columns with the layer of the new polymeric adsorbent polytrimethylsilylpropyne (PTMSP) as functions of the nature and pressure of the carrier gas. The retention factor k increases in the series helium < nitrogen < carbon dioxide. The k values depend linearly on the average pressure of the carrier gas in a capillary column with the adsorption PTMSP layer.     

High‐resolution peptide separations using nano‐LC at ultra‐high pressure

We report on the optimization of nano‐LC gradient separations of proteomic samples that vary in complexity. The gradient performance limits were visualized by kinetic plots depicting the gradient time needed to achieve a certain peak capacity, while using the maximum system pressure of 80 MPa. The selection of the optimal particle size/column length combination and corresponding gradient steepness was based on scouting the performance of 75 μm id capillary columns packed with 2, 3, and 5 μm fully porous silica C18 particles. At optimal gradient conditions, peak capacities up to 500 can be obtained within a 120 min gradient using 2 μm particle‐packed capillary columns. Separations of proteomic samples including a cytochrome c tryptic digest, a bovine serum albumin tryptic digest, a six protein mix digest, and an Escherichia coli digest are demonstrated while operating at the kinetic‐performance limit, i.e. using 2‐μm packed columns, adjusting the column length and scaling the gradient steepness according to sample complexity. Finally, good run‐to‐run retention time stability (RSD values below 0.18%) was demonstrated applying ultra‐high pressure conditions.     

Headspace sampling and GC analysis of volatile urinary metabolites

A method requiring only 1 to 3 ml of sample is developed for the analysis of volatile metabolites in urine. Trace volatiles are stripped with helium and concentrated on Porapak Q and activated charcoal traps in series. Volatiles are thermally desorbed into a fused silica capillary column for analysis by gas chromatography. Variables affecting the process are studied. Profiles of untreated and acid hydrolyzed urine are presented.     

Computer comparisons of variables in capillary gas chromatography

A series of computer-constructed van Deemter curves that permits evaluation of a number of variables in capillary gas chromatography is presented. The graphs permit the comparison of inter-related parameters, including the choice of carrier gas (hydrogen vs helium vs nitrogen), column length (10-100 m), column diameter (0.20, 0.25, 0.32, 0.4 mm), solute partition ratios (0-10), and liquid phase film thickness (0.1, 0.25, 0.5, 1.0 μm). The curves are evaluated, both in terms of the relative magnitude of the optimum average linear carrier gas velocity, and in terms of the significance of the sharpness of the curve.     

Analysis of methylphosphonic acid, ethyl methylphosphonic acid and isopropyl methylphosphonic acid at low microgram per liter levels in groundwater

A method is described for determining methylphosphonic acid, ethyl methylphosphonic acid and isopropyl methylphosphonic acid, which are hydrolysis products of the nerve agents VX (S-2-diisopropylaminoethyl O-ethyl methylphosphonothiolate) and GB (sarin, isopropylmethyl phosphonofluoridate). The analytes are extracted from 50 ml groundwater using a solid-phase extraction column packed with 500 mg of silica with a bonded quaternary amine phase, and are eluted and derivatized with methanolic trimethylphenylammonium hydroxide. Separation and quantitation are achieved using a capillary column gas chromatograph equipped with a flame photometric detector operated in its phosphorus-selective mode. Two independent statistically-unbiased procedures were employed to determine the detection limits, which ranged between 3 and 9 μg/l, for the three analytes.     

Fast supercritical fluid chromatography of polymers using packed capillary columns

Summary Fast separations of perfluorinated polyethers and polymethylsiloxanes that are composed of 50–80 oligomers were demonstrated in packed capillary column supercritical fluid chromatography (SFC) using a carbon dioxide mobile phase. Separations were accomplished within 10 min using a 13 cm×250 μm i.d. column packed with 2 μm porous octadecyl bonded silica (ODS) particles. Effects of particle diameter of the packing material and pressure programming on separation were investigated, and packed column SFC was compared with open tubular column SFC. Results show that as the particle diameter was decreased from 5 to 3 to 2 μm and the column length was reduced from 85 to 43 to 13 cm, the separation time could be reduced from 70 to 20 to 10 min while still maintaining similar separation (resolution). Short columns packed with small porous particles are very suitable for fast SFC separations of polymers.     

Aalysis of the fatty acid composition of the lipid classes in human blood serum under normal diet and when supplemented with fish oil

Total lipids have been extracted from human serum with chloroform–methanol 2:1 (v/v) and separated into individual classes by TLC. After transesterification the fatty acid methyl esters were analyzed by capillary gas chromatography on an FFAP column. The quantitation of ω-3 fatty acids has been performed using internal and external standards. Internal lipid standards for each lipid class were carried throughout the entire analytical procedure. Under normal diet eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) are incorporated into the lipid classes to different extents: cholesterol esters; EPA, 6.5 ± 1.9 γ/ml serum; DHA, 4.3 ± 1.9 μg/ml: phospholipids; EPA, 5.9 ± 2.7 μg/ml; DHA, 31.8 ± 8.1 μg/ml. Fish oil supplementation leads to a 4 to 6-fold rise in EPA and to an approximately 2-fold rise in DHA.     

Candidate EPA, NIOSH method for determining carbon disulfide in air with capillary gas chromatography by orthogonal design

This paper describes a candidate NIOSH EPA method for the determination of carbon disulfide in the air of workplaces with capillary gas chromatography using an orthogonal design. This method is designed to replace the packed column of the NIOSH method with a capillary column. The first part of this work concerned the setup of the method, particularly the choice of chromatographic parameters and finding their main favorable working ranges. The second part, using the statistical method orthogonal design, focused on optimizing the GC conditions, which were: column temperature, T(c) = 90 degrees C; injector temperature, T(i) = 140 degrees C; U section detector temperature, FPDU = 160 degrees C; L section detector temperature, FPDL = 210 degrees C; flow rate of carrier gas, F(c) = 20 cm/s; split ratio = 1/70; and injection volume = 1 microL. The quality control test showed that the coefficient of intra-day variation (CV) was 2.21%. A good logarithm linear correlation between the standard solutions and their peak areas was obtained. In general, the method reported here seems a valid candidate for a NIOSH EPA method due to its high precision and accuracy.     

Radiochemical detection for packed capillary liquid chromatography-mass spectrometry

For the identification of trace level organic molecules, such as drug or pesticide metabolites, there is need of a practical method to do packed capillary liquid chromatography-mass spectrometry (LC-MS) with radiochemical detection. This problem has been successfully solved by use of a post column flow-splitter, with coaxially transported makeup flow that increases the split flow rate to a flow compatible with commercially available radiochemical flow cells. To test the device, 14C-labeled azoxystrobin, a commercial fungicide, was analyzed by liquid chromatography-radiochemical activity monitor-mass spectrometry (LC-RAM-MS) using a 0.32 mm i.d. packed capillary column. Azoxystrobin could be detected at 500 pCi with good signal/noise. The method is general and can be used with capillary LC columns of smaller diameters. Column efficiency of about 20,000 theoretical plates/m was achieved using either radiochemical or mass spectrometric data, thus demonstrating the lack of band broadening using the described method for radiochemical detection. The simple hardware described allows the routine use of packed capillary LC with radiochemical detection.     

Automatic simulated distillation of heavy petroleum fractions up to 800°C TBP by capillary gas chromatography. Part I: Possibilities and limits of the method

The characterization of heavy petroleum fractions is essential for the design and improvement of cracking plants converting heavy feedstock into valuable “white” products. Conventional simulated distillation methods using packed columns are unsuitable for this purposes, being limited to boiling points up to about 600°C. The method presented is able to cover a boiling points interval ranging from about 150°C up to around 800°C. It employs a short, nonpolar, highly thermostable capillary column routinely operated at temperatures around 430°C. The analytical system is based on a high temperature versions of a fully automatic, capillary dedicated gas chromatograph. The experimental data demonstrate that cold on-column injection is the sole sampling system suitable for such heavy compounds. The conversion of the retention times into boiling points, based on the use of low molecular weight polyethylenes, is extremely reliable, as demonstrated by the excellent retention time reproducibilities. The lower part (up to 550–600°C TBP) of the boiling point distribution curves of heavy petroleum fractions obtained on capillary columns fits well with the corresponding distribution curves based on packed column data. For the petroleum fractions fully eluted from the column the quantitative results obtained either using internal standards or by direct processing of the elution curves are in excellent agreement (less than 0.3 weight% differences). The method has been applied to the determination of the true boiling points corresponding to short path vacuum distillation (DISTACT) cut points over 300°C.     

Effects of column length, particle size, gradient length and flow rate on peak capacity of nano-scale liquid chromatography for peptide separations

The effects of the column length, the particle size, the gradient length and the flow rate of a nanoLC system on peptide peak capacity were investigated and compared. Columns packed with 1.7 microm and 3 microm C(18) materials into pieces of 75 microm capillary tubing of various lengths were tested with different gradient lengths and flow rates. While increasing the length of a column packed with the 1.7 microm material helped improve peptide peak capacity at the whole range of the tested gradient lengths (24-432 min), little improvement in peak capacity was observed with the increase of the length of a column packed with the 3 microm material unless a gradient longer than 50 min was carried out. Up to 30% of peak capacity increase was observed when a column's length is doubled, with little reduction in the throughput. In most cases, more than 50% of the increase in peak capacity was obtained with the reduction in the particle size from 3 microm to 1.7 microm. With the same backpressure generated, a shorter 1.7-microm-particle column outperformed a longer column packed with the 3 microm material. In a flow rate range of 100-700 nl/min, increasing the flow rate improved peak capacity for columns packed with 1.7 microm and 3 microm materials.     

Separation of basic compounds of pharmaceutical interest by using nano-liquid chromatography coupled with mass spectrometry

Nano-liquid chromatography-mass spectrometry (nano-LC-MS) was evaluated for the separation of basic compounds of pharmaceutical interest. The separation of selected beta-blockers, namely nadolol, oxprenolol, alprenolol and propranolol in the presence of terbutaline was performed using two 75 microm I.D. capillaries packed with two different RP18 stationary phases (SP). The best results concerning resolution and efficiency were achieved using the SP where free silanol groups were not present. As expected, this latter SP proved to be very efficient and symmetry factors were observed mainly in the case of the more retained analytes. Baseline resolution of all studied basic compounds was achieved with the Cogent bidentate C18 silica phase (CBC18) eluting analytes at 800 nL/min with a mobile phase containing 500 mM ammonium acetate pH 4.5-water-methanol (1:8:91, v/v/v). The separated basic compounds were revealed using on-column UV detector at 205 nm and electrospray-ion-trap mass spectrometer (ESI-MS). The packed capillary was connected to the MS through a commercial sheath liquid interface or a sheathless nano-spray interface and in both cases the sensitivity was studied and the results compared. Limit of detection (LOD) as low as 0.1 ng/mL was measured for nadolol using the sheathless nano-spray interface and the capillary column packed with the CBC18 stationary phase.     

Evaluation of fused-silica capillary columns for GC/ECD analysis of chlorinated hydrocarbons listed in EPA method 8120

Four mega-bore, one wide-bore, and one narrow-bore fused-silica capillary columns were evaluated for their applicability to the GC/ECD analysis of 22 chlorinated hydrocarbons, some of which are currently targeted by EPA Method 8120. No one column can resolve all 22 compounds investigated here. Four compounds (two pairs) are coeluting on the SPB-35, DB-210, DB-WAX, and DB-519 fused-silica capillary columns, five compounds (two groups) are coeluting on the DB-1301 fused-silica capillary column, and ten compounds (five pairs) are coeluting on the SPB-5 fused-silica capillary column. The analysis time varies between 30 and 50 min. The order of elution of the chlorinated benzenes seems to depend on their boiling points rather than on the polarity of the liquid phase. The retention times of an additional nine chlorinated toluenes, eight chlorinated xylenes, and five chlorinated naphthalenes are also reported. Electron capture detector linearity is reported for the DB-210 fused-silica capillary column. Five brominated compounds were investigated as possible internal standards for Method 8120.