Sensitive and selective molecularly imprinted electrochemical sensor based on multi-walled carbon nanotubes for doxycycline hyclate determination

An electrochemical sensor for doxycycline hyclate(DC)detection with high sensitivity and good selectivity is reported.The sensor was fabricated by electro-polymerization of molecularly imprinted polymers(MIPs)in the presence of DC onto multi-walled carbon nanotubes modified glassy carbon electrode(MWCNTs/GCE).The MWCNTs can significantly increase the current response of the sensor,leading to enhanced sensitivity.The MIPs provide selective recognition sites for DC detection.The experimental parameters,such as the polymer monomer concentration,supporting electrolyte pH,the time for electro-polymerization and the incubation time of the sensor with DC were optimized.Under optimized experimental conditions,the sensor displayed a linear range of 0.05μmol/L-0.5μmol/L towards DC detection,with the detection limit of 1.3×10^-2μmol/L.The sensor was successfully applied for recovery test of DC in human serum samples.     

A nonenzyme glucose sensor based on Cu/Ni/CMWCNTs nanocompositesEI北大核心CSCD

Copper-nickel bimetallic nanoparticles decorated on carboxylated multi-walled carbon nanotubes （Cu/Ni/CMWCNTs）were prepared by using a simple one-pot solvothermal method,which was then employed to construct a highly sensitive non-enzymatic glucose sensor. The modified electrode showed high sensitivity and stability in glucose detection,which was mainly attributed to the synergistic effect of the compact copper-nickel nanocomposite and carboxylated multi-walled carbon nanotubes that possessing high specific surface area to increase the number of active sites and to improve the electrocatalytic activity of the modified electrode. The phase structure and morphology of the material were characterized by X-ray diffraction and scanning electron microscope; the electrochemical performance of the sensor was studied by cyclic voltammetry and chronoamperometry. The sensor had a sensitivity of 1949.1 μµA·L/（mmol·cm2）for glucose detection in the linear range of 1.0-8000 μµmol/L at a potential of 0.55 V,and the detection limit was 0.2 μµmol/L. The sensor was also applied to measure the concentration of glucose in serum samples. The developed nanocomposites sensor has the potential prospect to monitor blood glucose. © 2023, Youke Publishing Co.,Ltd. All rights reserved.     

用对氨基苯酚改性的碳纳米管糊电极同时测定羟胺和苯酚(英文)

A carbon paste electrode that was chemically modified with multiwall carbon nanotubes and p-aminophenol was used as a selective electrochemical sensor for the simultaneous detection of hydroxylamine (HX) and phenol. Cyclic voltammetry, double potential-step chronoamperometry, square wave voltammetry (SWV), and electrochemical impedance spectroscopy were used to investigate the use of p-aminophenol in the carbon nanotubes paste matrixes as a mediator for the electrocatalytic oxidation of HX and phenol in aqueous solution. The coefficient of electron transfer and catalytic reaction rate constant were determined using the electrochemical methods. Under optimized conditions, the electrocatalytic oxidation current peaks for HX and phenol increased linearly with concentration in the range of 0.5-180.0 and 10.0-650.0 μmol/L for HX and phenol, respectively. The detection limits for HX and phenol were 0.15 and 7.1 μmol/L, respectively. The anodic potential peaks of HX and phenol were separated by 0.65 V in SWV. Because of good selectivity and sensitivity, the present method provides a simple method for the selective detection of HX and phenol in practical samples such as water samples.     

以3,4-二羟基肉桂酸为介质的多壁碳纳米管糊电极用于检测药物和尿液样品中的谷胱甘肽(英文)

A sensitive and selective electrochemical sensor for the determination of glutathione(GSH) was developed using a modified multiwall carbon nanotube paste electrode with 3,4 dihydroxy cinnamic acid as a mediator.This modified electrode showed very high electrocatalytic activity for the anodic oxidation of GSH.Under the optimized conditions,the electrocatalytic peak current showed a linear relationship with GSH concentration in the range of 0.5-400.0 μmol/L with a detection limit of 0.1 μmol/L GSH.The relative standard deviations for seven successive assays of 5.0 and 25.0 μmol/L GSH were 2.2% and 2.7%,respectively.The modified electrode was used for the determination of GSH compounds in real urine samples.     

方波伏安法测定新型修饰多壁碳纳米管糊电极对肼的电催化氧化(英文)

The application of p-aminophenol as a suitable mediator, as a sensitive and selective voltammetric sensor for the determination of hydrazine using square wave voltammetric method were described. The modified multiwall carbon nanotubes paste electrode exhibited a good electrocatalytic activity for the oxidation of hydrazine at pH = 7.0. The catalytic oxidation peak currents showed a linear dependence of the peaks current to the hydrazine concentrations in the range of 0.5–175 μmol/L with a correlation coefficient of 0.9975. The detection limit (S/N = 3) was estimated to be 0.3 μmol/L of hydrazine. The relative standard deviations for 0.7 and 5.0 μmol/L hydrazine were 1.7 and 1.1%, respectively. The modified electrode showed good sensitivity and selectivity. The diffusion coefficient (D = 9.5 × 10–4 cm2/s) and the kinetic parameters such as the electron transfer coefficient (α = 0.7) of hydrazine at the surface of the modified electrode were determined using electrochemical approaches. The electrode was successfully applied for the determination of hydrazine in real samples with satisfactory results.     

在色氨酸存在下利用多壁碳纳米管糊电极和萘酚介质构成的伏安传感器测定N-乙酰半胱氨酸(英文)

A multiwall carbon nanotube modified electrode prepared by incorporating multiwall carbon nanotubes in the electrode of a sensor and naphthol green as a homogeneous mediator was used as a voltammetric sensor for the determination of N‐actylcysteine(N‐AC) in the presence of trypto-phan(Trp). The voltammograms of differential pulse voltammetry of N‐AC in a mixture with Trp were separated from each other by a potential difference of 200 mV, which allowed the determina-tion of both N‐AC and Trp simultaneously. Under the optimum conditions, the electrocatalytic cur-rents increased linearly with N‐AC concentration in the range of 0.25–400 μmol/L(two linear seg-ments with different slopes). The detection limit for N‐AC was 0.08 μmol/L. The kinetic parameters of the system were determined using electrochemical methods. The method was applied for the determination of N‐AC in drug and urine samples.     

银纳米颗粒的合成及用于抗癌药氟他胺的电化学检测（英文）

Ag nanoparticles were synthesized on the surface of a glassy carbon electrode modified with p‐tert‐butylcalix[4]arene and p‐tert‐butylcalix[6]arene by the deposition of Ag+ at an open circuit potential followed by the electrochemical reduction of the Ag+.The presence of the calixarene layer on the electrode surface controlled the particle size and prevented agglomeration.Cyclic voltam‐metry showed that the Ag nanoparticles on the modified glassy carbon electrode had good catalytic ability for the reduction of flutamide.The effects of calixarene concentration,potential applied for the reduction of Ag+,number of calixarene layers,and p H value on the electrocatalytic activity of the Ag nanoparticles were investigated.The modified electrode had a linear range in differential pulse voltammetry of 10-1000 μmol/L with a detection limit of 9.33 μmol/L for flutamide at an S/N = 3.The method was applied to the detection of flutamide in practical samples.     

在3,4-二羟基肉桂酸介质中以多壁碳纳米管为传感器电催化检测L-半胱氨酸(英文)

A highly sensitive electrochemical sensor was prepared for the determination of L-cysteine using a modified multiwall carbon nanotubes paste electrode in the presence of 3,4-dihydroxycinnamic acid(3,4-DHCA) as a mediator, based on an electrocatalytic process. The results indicate that the electrode is electrocatalytically efficient for the oxidation of L-cysteine in the presence of 3,4-DHCA. The interaction between the mediator and L-cysteine can be used for its sensitive and selective determination. Using chronoamperometry, the catalytic reaction rate constant was calculated to be 2.37 × 102 mol–1 L s–1. The catalytic peak current was linearly dependent on the L-cysteine concentration in the range of 0.4–115 μmol/L. The detection limit obtained by linear sweep voltammetry was 0.25 μmol/L. Finally, the modified electrode was examined as a selective, simple, and precise new electrochemical sensor for the determination of L-cysteine in real samples.     

Glucose biosensor based on new carbon nanotube-gold-titania nano-composites modified glassy carbon electrode

In this paper, a novel biosensor was prepared by immobilizing glucose oxidase （GOx） on carbon nanotube-gold-titania nanocomposites （CNT/Au/TiO2） modified glassy carbon electrode （GCE）. SEM was initially used to investigate the surface morphology of CNT/Au/TiO2 nanocomposites modified GCE, indicating the formation of the nano-porous structure which could readily facilitate the attachment of GOx on the electrode surface. Cyclic voltammogram （CV） and electrochemical impedance spectrum （EIS） were further utilized to explore relevant electrochemical activity on CNT]Au/TiO2 nanocomposites modified GCE. The observations demonstrated that the immobilized GOx could efficiently execute its bioelectrocatalytic activity for the oxidation of glucose. The biosensor exhibited a wider linearity range from 0.1 mmol L-1 to 8 mmol L^-1 glucose with a detection limit of 0.077 mmol L^- 1.     

用聚(L-蛋氨酸)/纳米金修饰玻碳电极同时灵敏检测多巴胺和尿酸(英文)

A novel electrochemical sensor was fabricated by electrodeposition of gold nanoparticles on a poly(L-methionine)(PMT)-modified glassy carbon electrode(GCE) to form a nano-Au/PMT composite-modified GCE(nano-Au/PMT/GCE).Scanning electron microscopy and electrochemical techniques were used to characterize the composite electrode.The modified electrode exhibited considerable electrocatalytic activity towards the oxidation of dopamine(DA) and uric acid(UA) in phosphate buffer solution(pH = 7.00).Differential pulse voltammetry revealed that the electrocatalytic oxidation currents of DA and UA were linearly related to concentration over the range of 5.0 ×10–8 to 10–6 mol/L for DA and 7.0 × 10–8 to 10–6 mol/L for UA.The detection limits were 3.7 × 10–8mol/L for DA and 4.5 × 10–8 mol/L for UA at a signal-to-noise ratio of 3.According to our experimental results,nano-Au/PMT/GCE can be used as a sensitive and selective sensor for simultaneous determination of DA and UA.     

基于叶片状氧化铜纳米材料的无酶葡萄糖传感电极

将Nafion交联剂与纳米材料修饰至玻碳电极基底制备一种无酶葡萄糖传感器,通过循环伏安曲线、时间-电流曲线检测该电极电化学特性. 氧化铜纳米复合膜具有高比表面积和多活性点位的优点. 实验结果表明,氧化铜纳米电极对葡萄糖的检测线性响应范围0.01 ~ 0.3 mmol·L^-1,灵敏度1783.58 μA·L·mmol^-1·cm^-2,检测限0.80 μmol·L^-1 (S/N=3),稳定性较好,能抵抗抗坏血酸、多巴胺和尿酸干扰.     

Amperometric nonenzymatic glucose sensor based on a glassy carbon electrode modified with a nanocomposite made from nickel(II) hydroxide nanoplates and carbon nanofibers

We report on a highly sensitive and selective nonenzymatic glucose sensor based on a glassy carbon electrode modified with a composite prepared from nickel(II) hydroxide nanoplates and carbon nanofibers. The nanocomposite was characterized by scanning electron microscopy and powder X-ray diffraction. Electrodes modified with pure Ni(OH)₂ and with the nanocomposite were characterized by electrochemical impedance spectroscopy. Cyclic voltammetric and amperometric methods were used to investigate the catalytic properties of the modified electrodes for glucose electrooxidation in strongly alkaline solution. The sensor exhibits a wide linear range (from 0.001 to 1.2 mM), a low detection limit (0.76 μM), fast response time (< 5 s), high sensitivity (1038.6 μA?·?mM^?1?·?cm^?2), good reproducibility, and long operational stability. Application of the nonenzymatic sensor for monitoring glucose in real samples was also demonstrated.

CuO Nanospheres Based Nonenzymatic Glucose Sensor

CuO nanospheres, synthesized by a simple one‐step hydrothermal method, have been applied to modify the glassy carbon (GC) electrode for sensitive nonenzymatic glucose detection. The CuO nanospheres modified electrode, compared to the Nafion modified GC electrode, exhibits an enhanced electrocatalytic property for direct glucose oxidation and shows a fast response and a high sensitivity for the amperometric detection of glucose. It has been determined that the dissolved oxygen is not involved in glucose oxidation and the high concentration of NaCl does not poison the electrode. These results also indicate that CuO nanospheres have great potential application in electrochemical detection.     

纳米氧化铜修饰的苯巴比妥分子印迹传感器的制备及其电化学性能

为了改善分子印迹传感器的灵敏度,在四丁基高氯酸铵的支持电解质溶液中,以甲基丙烯酸为功能单体,马来松香丙烯酸乙二醇酯为交联剂在纳米氧化铜修饰过的玻碳电极上电聚合了一种苯巴比妥(PB)识别性能的分子印迹传感膜.采用循环伏安(CV)法、差分脉冲伏安(DPV)法及交流阻抗(EIS)法对这种纳米氧化铜修饰过的印迹及非印迹电极的电化学性能进行了研究,结果显示纳米氧化铜修饰过的印迹及非印迹电极的电化学性能完全不同.X射线衍射(XRD)证实纳米粒子为氧化铜.采用扫描电镜(SEM)对纳米氧化铜修饰过的印迹传感器的形貌进行分析,发现纳米氧化铜分散在电极表面,改善了修饰印迹传感器的识别点.差分脉冲伏安法(DPV)表明苯巴比妥的浓度在1.0×10-8-1.8×10-4mol·L-1范围内呈现良好的线性关系(线性相关系数R=0.9994);检出限2.3×10-9mol·L-1(信噪比(S/N)=3).研究结果表明纳米氧化铜修饰过的印迹传感器具有较高灵敏度及选择性.此印迹传感器能用于实际样品中苯巴比妥的检测,加标回收率在95.0%-102.5%.     

Nonenzymatic sensor for glucose based on a glassy carbon electrode modified with Ni(OH)2 nanoparticles grown on a film of molybdenum sulfide

A glassy carbon electrode (GCE) was modified with nickel(II) hydroxide nanoparticles and a film of molybdenum sulfide. The nanocomposite was prepared by two-step electrodeposition. Scanning electron microscopy reveals that the nanoparticles are uniformly deposited on the film. Cyclic voltammetry and chronoamperometry indicate that this modified GCE displays a remarkable electrocatalytic activity towards nonenzymatic oxidation of glucose. Response is linear in the 10–1,300 μM concentration range (R ² ?=?0.9987), the detection limit is very low (5.8 μM), response is rapid (< 2 s), and selectivity over ascorbic acid, dopamine, uric acid, fructose and galactose is very good.

A highly sensitive nonenzymatic glucose sensor based on CuO nanowires

We report on the sensitive determination of glucose using a glassy carbon electrode modified with CuO nanowires and a Nafion film. The structure and morphology of CuO nanowires were established by scanning electron microscopy and X-ray diffraction. The electrochemical performance of the modified electrode was investigated by cyclic voltammetry and chronoamperometry. Compared to a bare glassy carbon electrode, a substantial increase in efficiency of the electrocatalytic oxidation of glucose can be observed. The new glucose sensor displays two useful linear ranges of response towards glucose, is not affected by commonly interfering species, and displays a detection limit as small as 45?nM. The response time is <2?s towards 0.5?mM of glucose. Additional features include high electrocatalytic activity, high sensitivity, excellent selectivity, and good stability.

Amperometric nonenzymatic determination of glucose based on a glassy carbon electrode modified with nickel(II) oxides and graphene

We have developed a stable and sensitive nonenzymatic glucose sensor by modifying a glassy carbon electrode (GCE) with a composite incorporating nickel(II) oxides and reduced graphene. The oxides were generated by directly electrodepositing nickel on the GCE with a graphene modifier using a multi-potential pulse process, and then oxidizing nickel to nickel(II) oxides by potential cycling. In comparison to the conventional nickel(II) oxides-modified GCE, this new nickel(II) oxides-graphene modified GCE (NiO-GR/GCE) has an about 1.5 times larger current response toward the nonenzymatic oxidation of glucose in alkaline media. The response to glucose is linear in the 20 μM to 4.5 mM concentration range. The limit of detection is 5 μM (at a S/N of 3), and the response time is very short (<3 s). Other beneficial features include selectivity, reproducibility and stability. A comparison was performed on the determination of glucose in commercial red wines by high-performance liquid chromatography (HPLC) and revealed the promising aspects of this sensor with respect to the determination of glucose in real samples.

纳米氧化铜修饰的苯巴比妥分子印迹传感器的制备及其电化学性能

为了改善分子印迹传感器的灵敏度, 在四丁基高氯酸铵的支持电解质溶液中, 以甲基丙烯酸为功能单体, 马来松香丙烯酸乙二醇酯为交联剂在纳米氧化铜修饰过的玻碳电极上电聚合了一种苯巴比妥(PB)识别性能的分子印迹传感膜. 采用循环伏安(CV)法、差分脉冲伏安(DPV)法及交流阻抗(EIS)法对这种纳米氧化铜修饰过的印迹及非印迹电极的电化学性能进行了研究, 结果显示纳米氧化铜修饰过的印迹及非印迹电极的电化学性能完全不同. X射线衍射(XRD)证实纳米粒子为氧化铜. 采用扫描电镜(SEM)对纳米氧化铜修饰过的印迹传感器的形貌进行分析, 发现纳米氧化铜分散在电极表面, 改善了修饰印迹传感器的识别点. 差分脉冲伏安法(DPV)表明苯巴比妥的浓度在1.0×10^-8-1.8×10^-4 mol·L^-1 范围内呈现良好的线性关系(线性相关系数R=0.9994); 检出限2.3×10^-9 mol·L^-1 (信噪比(S/N)=3). 研究结果表明纳米氧化铜修饰过的印迹传感器具有较高灵敏度及选择性. 此印迹传感器能用于实际样品中苯巴比妥的检测, 加标回收率在95.0%-102.5%.     

Nonenzymatic glucose detection at ordered mesoporous carbon modified electrode

This work reports on a novel nonenzymatic amperometric glucose sensor based on the ordered mesoporous carbon (OMC). Amperometric method was used to evaluate the electrocatalytic activity of the OMC modified electrode toward nonenzymatic glucose in alkaline media in presence and absence of chloride ions. The results indicated that OMC showed electrocatalytic activity for the oxidation of glucose in alkaline solution. The resulting biosensor exhibited excellent performance for glucose determination with high sensitivity of 10.81 μA/mM and a low detection limit of 0.02 mM. The OMC modified electrode is also to resistant the interference from common interfering substances such as ascorbic acid, dopamine and uric acid.     

Preparation and characterization of Ni(II)/polyacrylonitrile and carbon nanotube composite modified electrode and application for carbohydrates electrocatalytic oxidation

A nickel(II) into porous polyacrylonitrile–carbon nanotubes composite modified glassy carbon electrode (Ni/PAN-CNT/GCE) was fabricated by simple drop-casting and immersing technique. The unique electrochemical activity of Ni/PAN-CNT composite modified glassy carbon electrode was illustrated in 0.10?M NaOH using cyclic voltammetry. The Ni/PAN-CNT/GCE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple compared with Ni/PAN/GCE and Ni/CNT/GCE. The results of electrochemical impedance spectroscopy and scanning electron microscopy indicated the successful immobilization for PAN-CNT composite film. Kinetic parameters such as the electron transfer coefficient, α, and rate constant, k _s, of the electrode reaction were determined. Ni/PAN-CNT/GCE also shows good electrocatalytic activity toward the oxidation of carbohydrates (glucose, sucrose, fructose, and sorbitol). The electrocatalytic response showed a wide linear range (10–1,500, 12–3,200, 7–3,500, and 16–4,200?μM for glucose, sucrose, fructose, and sorbitol, respectively) as well as its experimental limit of detection can be achieved 6, 7, 5, and 11?μM for glucose, sucrose, fructose, and sorbitol, respectively. The modified electrode for carbohydrates determination is of the property of simple preparation, good stability, and high sensitivity.