Cobalt(II) octanoate and cobalt(II) perfluorooctanoate catalyzed atom transfer radical polymerization of styrene in toluene and fluorous media—A versatile route to catalyst recycling and oligomer formation

Cobalt(II) perfluorooctanoate‐catalyzed atom transfer radical polymerization (ATRP) and reverse ATRP were developed to prepare oligostyrenes (M_n < 2500) with low polydispersities M_w/M_n < 1.5. Fluorous biphase catalysis was applied for effective recycling of catalyst and fluorous solvent. The homogeneous polymerization reaction was performed at 90 °C in toluene/cyclohexane/perfluorodecalin mixture (1:1:1) and fluorine‐free solvents. Temperature‐induced phase separation of this fluorous solvent mixture occurred at room temperature and proved to be the key for the very effective separation of the cobalt(II) perfluorooctanoate from the oligostyrene and fluorine‐free solvents. Both the fluorine‐tagged cobalt catalysts and the fluorous media were recycled and reused up to three times without encountering catalyst activity losses. The roles of cobalt catalysts, fluorous media, and monomer/initiator ratio were examined with respect to the polymerization kinetics. Fluorine‐containing and fluorine‐free cobalt(II) octanoate catalyzed controlled styrene oligomerization according to the ATRP mechanism. The molar mass control range was limited in fluorous biphase catalysis most likely because of precipitation of high molar mass polystyrenes in the fluorous reaction medium. To the best of our knowledge, this is the first time temperature‐induced phase separation of fluorous and fluorine‐free solvents has been successfully applied to polymerization processing. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3804–3813, 2005     

Efficient, recoverable, copper-free Sonogashira reaction under FBS and thermomorphic mode

The solubility property of high fluorine content ligands allows us to report in this article the accomplishment under the fluorous biphasic system (FBS) the Pd-catalyzed Sonogashira reactions using novel recyclable Pd catalysts with fluorous-ponytails in the structure of 2,2′-bpy ligands that are only soluble in perfluorinated solvents at room temperature. Alternatively, without using any fluorous solvent but under the thermomorphic mode, the same Pd catalysts proceed with the Cu-free Sonogashira reactions homogeneously in DMF at 135 ± 5 °C, whereas the product mixtures after reaction remain in solution and the Pd catalysts precipitate from DMF at low temperature.     

Fluorophilicity switch by solvation

A new type of fluorous distannoxanes, [XRf2SnOSnRf2Y]2 (Rf = C6F13C2H4; X, Y = C6F13SO3 (2) and (C6F13SO2)2N, Cl (3)) was prepared successfully as hydrates from the reaction of [ClRf2SnOSnRf2Cl]2 with C6F13SO3Ag and (C6F13SO2)2NAg, respectively. Despite their high fluorine content (59.85 and 59.27% F), these distannoxanes were completely insoluble in fluorocarbons as well as hydrocarbons and halo alkanes. In contrast to this, fluorous distannoxanes 2 and 3 were soluble in polar organic solvents, such as EtOAc, acetone, and THF. When 2 and 3 were added to a two-phase mixture of fluorocarbon and EtOAc, the mixture turned miscible in proportion to the amount of 2 and 3 added, and finally, the mixture turned to a homogeneous solution.     

Synthesis and properties of organosoluble polyimides based on novel perfluorinated monomer hexafluoro-2,4-toluenediamine

New highly fluorinated aromatic polyimides based on hexafluoro-2,4-toluenediamine and commercially available dianhydrides (6FDA and ODPA) were synthesized by one-pot high temperature polycondensation in benzoic acid melt. Owing to the CF₃ group and fluorine atoms in the meta-linked phenylenediamine fragment, these polyimides combine good solubility in organic solvents including such a low boiling point solvent as chloroform with high glass transition temperatures (330-345 °C), thermal and thermooxidative stability (T₅ is >500 °C). The highly fluorinated polyimide films (hydrogen content is ≤1%) exhibit good dielectric properties and low water absorption as well as excellent optical transparency in the UV-vis region (cut-off wavelength is 311 nm for 6FDA-based and 357 nm for ODPA-based polyimides), which is very important for optoelectronic materials.     

Synthesis and properties of a novel family of fluorous triphenylphosphine derivatives

A novel approach to the preparation of perfluorotail-functionalized triarylphosphines using a p-silyl substituent as the branching point has been developed. This approach enabled the attachment of between three and nine perfluorotails per phosphorus atom, resulting in the production of highly fluorous tris[p-(1H,1H,2H, 2H-perfluoroalkylsilyl)aryl]phosphines, P[C(6)H(4)-p-SiMe(3)(-)(n)()(CH(2)CH(2)C(x)()F(2)(x)()(+1))(n)()](3) (n = 1, 2, 3; x = 6, 8), containing between 50 and 67 wt % fluorine. (31)P NMR studies indicate that the phosphorus atoms, and consequently the sigma-donor and pi-acceptor properties of these phosphines, are not influenced by the electron-withdrawing perfluoroalkyltails. The fluorous triarylphosphines are readily soluble in fluorous solvents and display fluorous phase preference in several fluorous biphasic systems. The phase partitioning of these fluorous ligands, as well as their donor properties, is discussed in relation to their potential for fluorous biphasic catalyst separation.     

Highly fluorinated graphite prepared from graphite fluoride formed using BF3 catalyst

Fluorinated graphites (CF_0.47) were obtained by reaction at room temperature of fluorine gas with graphite in the presence of boron trifluoride and hydrogen fluoride as catalysts. Their thermal treatments under fluorine at temperatures up to 600 °C lead to a progressive increase of the fluorine level resulting in an highly fluorinated graphite (CF_1.02). Whatever the fluorination level, a stage one fluorine-graphite intercalation compound is obtained. The sp² carbon hybridization is maintained for treatment temperature below 300 °C and two types of structure coexist for T_T in the range 350-550 °C. Finally, above 550 °C, carbon hybridization is sp³.The resulting materials were studied by ¹¹B, ¹H, and ¹⁹F NMR and EPR at different experimental temperatures giving informations about the intercalated fluoride species, the temperature of their removal from the host fluorocarbon matrix, as well as their mobility.     

Efficient condensation of carboxylic acids with alcohols catalyzed by fluorous ammonium triflates

The use of fluorous ammonium salts as metal-free catalysts for the direct condensation of equimolar amounts of carboxylic acids and aliphatic alcohols has been investigated. Esterification reactions were thus conveniently carried out under mild fluorous biphasic conditions, in the presence of 1 mol % of fluorous ammonium triflate and without recourse to any additional water removal technique. Good to excellent ester yields were obtained in the case of primary and secondary aliphatic alcohols. The fluorous salt was easily recovered by simple phase separation and reused at least three times without considerable loss of activity.     

Evaluation of the hydrophobicity of perfluoroalkyl chains in amphiphilic compounds that are incorporated into cell membrane

Incubation of animal cells in the presence of amphiphilic glycosides having a lactoside residue (hydrophilic moiety) and various kinds of perfluoroalkyl chain (hydrophobic moiety) resulted to glycosylation of the saccharide chain by cellular enzymes and afforded glycolipid-like compounds. The amounts of amphiphilic glycoside and glycolipid-like compounds found in the cell and culture medium fractions, respectively, varied depending on the fluorine content of the perfluoroalkyl chain. To investigate further, the hydrophobicity of the perfluoroalkyl chain was estimated from the critical micelle concentration values and was found to be 1.5 times larger in hydrophobicity than the hydrocarbon chain [CF₂ = 1.5CH₂]. Liposomes resembling cells in size were also prepared and the amphiphilic glycosides were introduced. Results showed a positive correlation between hydrophobicity and localization of amphiphilic glycoside into liposomes. The amount of amphiphilic glycosides localized in liposomes increased with increasing hydrophobicity that is attributed mainly to the fluorine content of the aglycon. In spite of the low affinity of fluorous chain for hydrocarbon chain, the amphiphilic fluorous compounds showed high affinity for cell membrane that is composed of amphiphilic phospholipids.     

Fluorous biphasic catalysis with dirhodium(II) perfluorocarboxylates: selective silylation of alcohols under fluorous biphasic conditions

Dirhodium(II) perfluorocarboxylates bearing C7–C13 perfluoroalkyl chains have been prepared and used as catalysts under fluorous biphasic conditions. They were found to be active and recyclable catalysts for the silylation of alcohols with triethylsilane. Hydrophobic, primary alcohols are preferentially silylated by the fluorous biphasic catalytic system in comparison with hydrophilic or secondary ones. This opens the way to the development of selective silylation protocols.     

Fluorous Tagged Peptides for Intracellular Delivery and Biomedical Imaging

Fluorous tagged peptides have shown promising features for biomedical applications such as drug delivery and multimodal imaging. The bioconjugation of fluoroalkyl ligands onto cargo peptides greatly enhances their proteolytic stability and membrane penetration via a proposed “fluorine effect”. The tagged peptides also efficiently deliver other biomolecules such as DNA and siRNA into cells via a co-assembly strategy. The fluoroalkyl chains on peptides with antifouling properties enable efficient gene delivery in the presence of serum proteins. Besides intracellular biomolecule delivery, the amphiphilic peptides can be used to stabilized perfluorocarbon-filled microbubbles for ultrasound imaging. The fluorine nucleus on fluoroalkyls provides intrinsic probes for background-free magnetic resonance imaging. Labeling of fluorous tags with radionuclide ¹⁸F also allows tracing the biodistribution of peptides via positron emission tomography imaging. This mini-review will discuss properties and mechanism of the fluorous tagged peptides in these applications.     

Fluorination of single walled carbon nanotubes at low temperature: Towards the reversible fluorine storage into carbon nanotubes

Fluorination of single walled carbon nanotubes was carried out at low temperature in the −191/25 °C range under 1 atm pure fluorine gas. In such conditions, the resulting C–F bonding is significantly weaker than for samples fluorinated at 280 °C. If the fluorination is performed at low temperature, fluorine atoms can be then removed from the host structure by moderated heating until 300 °C or by vacuum without strong damage on the tubes. After thermal defluorination, the resulting sample can be refluorinated similarly than the pristine tubes.     

Influence of fluorine-containing lubricant on properties of NR/BR rubber

K95 experimental lubricant being a product of fluorine reaction with a blend of mutually soluble poly(fluorine alcohols) and poly(fluorine esters) with molecular weight 240-900 g/mol was studied as an additive for rubber compounds based on blend of NR and BR. It was thermally stable till 270-300 °C. For comparison, it was tested simultaneously with homogenizing agent, Struktol MS40. Lubricant K95 added in a quantity of 0.5 wt% reduced the viscosity of rubber compound; it also improved compound flow in the mold. Mechanical properties of cured rubber not decrease while resistance to abrasion and fatigue increased. K95 participated in forming strong physical junctions (lower molecular weight between junctions of thermally stable network) while Struktol MS40 reduced the networking degree of rubber. As a result, it acts a multifunctional additive for NR/BR rubber.     

Surface fluorination and electrochemical behavior of petroleum cokes graphitized at medium and high temperatures for secondary lithium battery

The surface structure and electrochemical performance have been investigated of petroleum cokes heat-treated at 2100 and 2600 °C (abbreviated to PC2100 and PC2600) and those fluorinated by elemental fluorine at 200 and 300 °C. XPS study indicated that surface fluorine was covalently bonded to carbon and surface fluorine contents were in the range of 4.9-17.8 at.%. Surface oxygen was reduced by fluorination. BET surface areas were nearly the same before and after fluorination. Fluorination enhanced D-band intensity in two Raman shifts observed at 1580 cm⁻¹ (G-band) and 1360 cm⁻¹ (D-band), indicating the increase in the surface disordering. At a high current density of 150 mA/g, the capacity increase was observed for PC2100 fluorinated at 200 °C and for PC2600 fluorinated at 200 and 300 °C. The most interesting result was the increase in first coulombic efficiencies by surface fluorination. First columbic efficiencies for PC2600 fluorinated at 300 °C were increased by 12.1% at 60 mA/g and by 25.8% at 150 mA/g, respectively. The impedance measurements showed that the resistances of surface films on carbon electrodes were increased by fluorination, however, the charge transfer resistances were decreased by 12.3% for PC2100 fluorinated at 200 °C, and by 27.5 and 6.4% for PC2600 fluorinated at 200 and 300 °C, respectively. The reduction of the charge transfer resistances was consistent with increase in the charge capacities for PC2100 fluorinated at 200 °C and PC2600 fluorinated at 200 and 300 °C.     

Rhodium-catalyzed carbonyl allylations by allylic alcohols with tin(II) chloride

Rhodium complexes such as [RhCl(cod)]₂, [Rh(cod)₂]BF₄, and [Rh(cod)(CH₃CN)₂]BF₄ function as catalysts for carbonyl allylations by allylic alcohols with 1 equimolar amount of tin(II) chloride to each allylic alcohol and aldehyde in THF at 50 °C to produce the corresponding homoallylic alcohols.     

Novel fluorous prolinol as a pre-catalyst for catalytic asymmetric borane reduction of various ketones

Novel prolinol carrying two perfluorohexylethyl groups at the α-position was prepared from l-proline as a starting chiral substrate. Catalytic asymmetric reduction of various ketones, including mono-, di-, and trifluoromethylated acetophenones, using fluorous oxazaborolidines derived from fluorous prolinol afforded the corresponding alcohols in good to excellent yields and with high enantioselectivities (up to 93.2% ee). The fluorous prolinol was recovered without any fluorous solvents or silica gel by simply cooling the organic phase and filtration.     

Yb[N(SO2C8F17)2]3-catalyzed allylation of 1,3-dicarbonyl compounds with allylic alcohols in a fluorous biphase system

Allylation of 1,3-dicarbonyl compounds with allylic alcohols was successfully accomplished using rare earth metal (III) bis(perfluorooctanesulfonyl)imide [RE(NPf₂)₃, RE = La∼Lu] as catalysts in fluorous solvents. Ytterbium bis(perfluorooctanesulfonyl)imide [Yb(NPf₂)₃] catalyzes the high efficient reaction of allylation in fluorous solvents. By simple separation, fluorous phase containing only catalyst can be reused several times.     

Fluorocarbon soluble copper(II) carboxylate complexes with nonfluoroponytailed nitrogen ligands as precatalysts for the oxidation of alkenols and alcohols under fluorous biphasic or thermomorphic modes: structural and mechanistic aspects

This fluorous biphasic catalysis (FBC) contribution was focused on the synthesis and characterization of new fluorous soluble R(f)-Cu(II) carboxylate complexes containing nonfluoroponytailed ligands and defines their role as precatalysts for the FBC oxidation of alkenols and alcohols in the presence of 2,2,6,6-tetramethylpiperidine-N-oxyl (TEMPO)/O(2). In this FBC approach, we have utilized the phase-switching technique of Vincent et al. (J. Am. Chem. Soc. 2002, 124, 12942) to solubilize the nonfluoroponytailed ligands, N-1,4,7-Me(3)TACN, 2, and N-1,4,7-pentamethyldiethylenetriamine (PMDETA), 3, by reaction with a fluorous solvent-soluble copper (II) dimeric complex, [Cu({C(8)F(17)(CH(2))(2)}(2)CHCO(2))(2)](2), 1. Moreover, the reaction of nonfluoroponytailed ligands 2 and 3 with 1 afforded new perfluoroheptane-soluble Cu(II) complexes, [Cu({C(8)F(17)(CH(2))(2)}(2)CHCO(2))(2)(2)], 4, and [Cu({C(8)F(17)(CH(2))(2)}(2)CHCO(2))(2) (3)], 5, respectively. The known Cu(II) complex, 1, was further characterized by electron paramagnetic resonance (EPR) spectroscopy confirming its dimeric structure, while 4 and 5 were characterized by elemental analysis, IR, diffuse reflectance UV-vis, and EPR spectroscopy. Furthermore, 1, 4, and 5 were evaluated as precatalysts for alkenol and alcohol oxidation. The oxidation reactions of alkenols and alcohols in the presence of TEMPO/O(2) proceeded under FBC conditions for 1, 4, and 5, but 1-octanol was unreactive under single-phase FBC conditions at 90 degrees C with TEMPO/O(2). The thermomorphic property of 5, soluble in chlorobenzene/toluene at 90 degrees C but insoluble at room temperature, was also evaluated in the selective oxidation of p-nitrobenzyl alcohol to p-nitrobenzaldehyde. Plausible mechanisms concerning these FBC/thermomorphic oxidation reactions will be discussed.     

Second generation fluorous DEAD reagents have expanded scope in the Mitsunobu reaction and retain convenient separation features

First generation fluorous DEAD reagent bis(perfluorohexylethyl)azo dicarboxylate (C(6)F(13)(CH(2))(2)O(2)CN=NCO(2)(CH(2))(2)C(6)F(13), F-DEAD-1) has been shown to underperform relative to diisopropylazodicarboxylate in difficult Mitsunobu reactions involving hindered alcohols or less acidic pronucleophiles (phenols). Two new second generation fluorous reagents bearing propylene spacers instead of the ethylene spacers show expanded reaction scope while retaining the easy fluorous separation features. Byproducts from "half fluorous" reagent perfluorooctylpropyl tert-butyl azo dicarboxylate (C(8)F(17)(CH(2))(3)O(2)CN=NCO2(t)Bu, F-DEAD-2) can be removed by fluorous flash chromatography, and byproducts from bis(perfluorohexylpropyl)azo dicarboxylate (C(6)F(13)(CH(2))(3)O(2)CN=NCO(2)(CH(2))(3)C(6)F(13), F-DEAD-3) can be removed by fluorous solid-phase extraction. The new reagents promise to provide general and complementary solutions for separation problems in Mitsunobu reactions without restricting reaction scope.     

Short-Chained Platinum Complex Catalyzed Hydrosilylation under Thermomorphic Conditions: Heterogeneous Phase Separation at Ice Temperature

Homogeneous catalysts PtCl₂[5,5′-bis-(n-ClCF₂(CF₂)₃CH₂OCH₂)-2,2′-bpy] (2A) and PtCl₂[5,5′-bis-(n-HCF₂(CF₂)₃CH₂OCH₂)-2,2′-bpy] (2B), which contained short fluorous chains, were synthesized and used in catalysis of hydrosilylation of alkynes. In these reactions the thermomorphic mode was effectively used to recover these catalysts from the reaction mixture up to eight cycles by taking advantage of heterogeneous phase separation at ice temperature. This kind of catalysis had previously been observed in fluorous catalysts of platinum containing about 50% F-content, but in this work the percentage of F-content is decreased to only about 30%, by which we termed them as “very light fluorous”. Our new type of catalyst with limited number of F-content is considered as the important discovery in the fluorous technology field as the reduced number of fluorine atoms will help to be able to comply the EPA 8-carbon rule. The metal leaching after the reaction has been examined by ICP-MS, and the testing results show the leaching of residual metal to be minimal. Additionally, comparing these results to our previous work, fluorous chain assisted selectivity has been observed when different fluorous chain lengths of the catalysts are used. It has been found that there exists fluorous chain assisted better selectivity towards β-(E) form in the Pt-catalyzed hydrosilylation of non-symmetric terminal alkyne when the Pt catalyst contains short fluorous chain (i.e., 4 Cs). Phenyl acetylenes showed the opposite regioselectivity due to pi-pi interaction while using the same catalyst via Markovnikov’s addition to form terminal vinyl silane, which is then a major product for Pt-catalyzed hydrosilylation of terminal aryl acetylene with triethylsilane. Finally, the kinetic studies indicate that the insertion of alkyne into the Pt-H bond is the rate-determining step.     

Organic fluorine compounds: a great opportunity for enhanced materials properties

Interactions of "organic fluorine" have gained great interest not only in the context of crystal engineering, but also in the systematic design of functional materials. The first part of this tutorial review presents an overview on interactions known by organic fluorine. This involves π-π(F), C-F···H, F···F, C-F···π(F), C-F···π, C-F···M(+), C-F···C=O and anion-π(F) interactions, as well as other halogen bonds. The effect of the exchange of H vs. F is discussed by means of several examples and a short introduction to the young field of "fluorous" chemistry is given. The second part is dedicated to numerous applications of fluorine and fluorous interactions. It is shown how application of fluorination is used to enable a number of reactions, to improve materials properties and even open up new fields of research.