Separation and preconcentration by a cloud point extraction procedure for determination of metals: an overview

Recently, cloud point extraction (CPE) has been an attractive subject as an alternative to liquid–liquid extraction. The technique is based on the property of most non-ionic surfactants in aqueous solutions to form micelles and become turbid when heated to the cloud point temperature. This review covers a selection of the literature published on applications of CPE in determination of metal ions over the period between 2004 and 2008.     

Cloud point extraction preconcentration for capillary electrophoresis of metal ions

The application of the cloud point extraction (CPE) technique for capillary electrophoresis (CE) determination of metal ions was demonstrated using Cu(II) and Co(II) as model metal ions. The preconcentration of Cu(II) and Co(II) in aqueous solution was achieved by CPE with 1-(2-pyridylazo)-2-naphthol (PAN) as the chelating agent and Triton X-114 as the extractant. Baseline separation of the PAN chelates of Cu(II) and Co(II) was realized by CE with a photodiaode array detector in a  μm i.d. fused-silica capillary at 17 kV. A 50 mM NH₄Ac buffer solution (pH 8.0) containing 0.2 mM of PAN in 80% (v/v) of acetonitrile and 20% (v/v) doubly deionized water (DDW) was used as the separation medium to avoid the adsorption of hydrophobic substances and nonionic surfactant Triton X-114 onto the inner surface of the separation capillary, ensuring the separation efficiency and reproducibility. The precision (relative standard deviation (R.S.D.), n=5) for five replicate injections of a mixture of 20 μg/l of Co(II) and Cu(II) were 0.74 and 1.8% for the migration time, 3.1 and 0.64% for the peak area measurement, respectively. The apparent concentration factor, which is defined as the concentration ratio of the analyte in the final diluted surfactant-rich extract ready for CE separation and in the initial solution, was 15.9 for Co(II) and 16.3 for Cu(II). The linear concentration range was from 3 to 100 μg/l for both Co(II) and Cu(II). The detection limits of Co(II) and Cu(II) were 0.12 and 0.26 μg/l, respectively. The developed method was successfully applied to the determination of Co(II) and Cu(II) in tap water, snow water, and flavor wines.     

Development of a cloud point extraction and preconcentration method for determination of trace aluminum in mineral waters by FAAS

A cloud point extraction (CPE) method has been developed for the preconcentration of trace aluminum prior to its determination by flame atomic absorption spectrometry (FAAS). The CPE method is based on the complex of Al(III) with Xylidyl Blue (XB) and then entrapped in non-ionic surfactant Triton X-114. The main factors affecting CPE efficiency, such as pH of sample solution, concentration of XB and Triton X-114, equilibration temperature and time, were investigated in detail. An enrichment factor of 50 was obtained for the preconcentration of Al(III) with 50 mL solution. Under the optimal conditions, the detection limit of this method for Al(III) is 1.43 μg L^− 1, and the relative standard deviation is 2.7% at determination of 100 μg L^− 1 Al(III). The proposed method has been applied for determination of trace amount of aluminum in mineral water samples with satisfactory results. Also, the proposed method was applied to the certified reference materials. The results obtained were in good agreement with certified values.     

An on-line cloud point extraction system for flame atomic absorption spectrometric determination of trace manganese in food samples

The development of an on-line preconcentration system with cloud point extraction for the determination of manganese is described. The system was used to determine manganese levels in food samples using flame atomic absorption spectrometry (FAAS). All steps of the cloud point extraction procedure were performed on-line, from the mixing of reagents to detection. The manganese ions are complexed in a mixture of the reagent 2-[2′-(6-methyl-benzothiazolylazo)]-4-bromophenol (Me-BTABr) and Triton X-114. The components are retained on a minicolumn and then desorbed with eluent acid to subsequent detection of manganese by FAAS. Under the optimized conditions, the method presented a detection limit of 0.7 μg L^− 1 and an enrichment factor of 17 to a volume of 3000 μL. The sampling frequency was 30 h^− 1. The accuracy of the method was tested by evaluating the amount of Mn in certified reference materials (apple leaves NIST 1515 and spinach leaves NIST 1570a). The proposed procedure was applied to food samples (shrimp powder, flaxseed flour, wheat flour, soy flour and oat), and the results agreed with those obtained by the determination of Mn in foods by atomic absorption spectrometry with electrothermal atomization (ETAAS).     

Development of a new sequential injection in-line cloud point extraction system for flame atomic absorption spectrometric determination of manganese in food samples

A preconcentration method for manganese determination by sequential injection cloud point extraction with subsequent detection by flame atomic absorption spectrometry (FAAS) has been developed. The enrichment of Mn was performed after a preliminary on-line cloud point extraction and entrapment of manganese-containing surfactant aggregated within a minicolumn packed with cotton. The laboratory-made reagent 4-(5′-bromo-2′-thiazolylazo)orcinol (Br-TAO) and the surfactant Triton X-114 were used for cloud point extraction. The manganese ions were eluted with sulphuric acid solution and directly introduced into the FAAS. Chemical and flow variables affecting the preconcentration were studied. Using a sample volume of 2.80 mL the limit of detection and enrichment factor were calculated to be 0.5 μg L⁻¹ and 14, respectively. The sample frequency is 48 h⁻¹, considering a total run cycle of 75 s. The accuracy of the proposed method has been demonstrated by the analysis of the certified reference biological materials rice flour and tomato leaves. The method has been applied to determination of manganese in food samples.     

Analysis of persistent organic pollutants in marine sediments using a novel microwave assisted solvent extraction and liquid-phase microextraction technique

A simple and novel analytical method for quantifying persistent organic pollutants (POPs) in marine sediments has been developed using microwave assisted solvent extraction (MASE) and liquid-phase microextraction (LPME) using hollow fibre membrane (HFM). POPs studied included twelve organochlorine pesticides (OCP) and eight polychlorinated biphenyl (PCB) congeners. MASE was used for the extraction of POPs from 1 g of sediment using 10 ml of ultrapure water at 600 W for 20 min at 80 degrees C. The extract was subsequently subjected to a single step LPME-HFM cleanup and enrichment procedure. Recovery varied between 73 and 111% for OCPs; and 86-110% for PCBs, and exceeded levels achieved for conventional multi-step Soxhlet extraction coupled with solid-phase extraction. The method detection limit for each POP analyte ranged from 0.07 to 0.70 ng g(-1), and peak areas were proportional to analyte concentrations in the range of 5-500 ng g(-1). Relative standard deviations of less than 20% was obtained, based on triplicate sample analysis. The optimized technique was successfully applied to POP analysis of marine sediments collected from the northeastern and southwestern areas of Singapore's coastal environment.     

A review of the determination of persistent organic pollutants for environmental forensics investigations

The field of environmental forensics emerged in the 1980s as a consequence of legislative frameworks enacted to enable parties, either states or individuals, to seek compensation with regard to contamination or injury due to damage to the environment. This legal environment requires stringent record keeping and defendable data therefore analysis can sometimes be confined to data to be obtained from certified laboratories using a standard accredited analytical method. Many of these methods were developed to target specific compounds for risk assessment purposes and not for environmental forensics applications such as source identification or age dating which often require larger data sets. The determination of persistent organic pollutants (POPs) for environmental forensic applications requires methods that are selective but also cover a wide range of target analytes which can be identified and quantified without bias. POPs are used in a wide variety of applications such as flame retardants, fire suppressants, heat transfer agents, surfactants and pesticides mainly because of their chemical inertness and stability. They also include compounds such as dioxins that can be unintentionally produced from industrial activities. POPs are persistent in the environment, bioaccumulative and/or toxic and therefore require analytical methods that are sensitive enough to meet the low detection limits needed for the protection of the environment and human health. A variety of techniques, procedures and instruments can be used which are well suited for different scenarios. Optimised methods are important to ensure that analytes are quantitatively extracted, matrix coextractables and interferences are removed and instruments are used most effectively and efficiently. This can require deviation from standard methods which can open the data up to further scrutiny in the courtroom. However, when argued effectively and strict QA/QC procedures are followed the development and optimization of methods based on investigation specific scenarios has the potential to generate better quality and more useful data.     

浊点萃取-分光光度法测定痕量NO2-

建立了浊点萃取-分光光度法测定痕量NO2-根的方法.以对氨基苯磺酸和α-萘胺为络合剂,非离子型表面活性剂TritonX-100为萃取剂,富集、分离水样中痕量NO2-,采用可见吸收光谱法进行检测.研究了溶液的酸度、试剂用量、平衡时间、平衡温度、干扰离子对浊点萃取效果的影响,并得到最佳实验条件:5％的TritonX-100用量2.0mL、平衡温度85℃、平衡时间10min、对氨基苯磺酸和α-萘胺均为0.3mL、0.1mol/LH2SO4溶液0.5mL.在最佳实验条件下,对氨基苯磺酸、α-萘胺和NO2-生成的络合物被萃取到TritonX-100表面活性剂相并与水相分开.该方法适用于环境水样中痕量NO2-的测定.     

Fiber optic-linear array detection spectrophotometry in combination with cloud point extraction for simultaneous preconcentration and determination of cobalt and nickel

A new combined method including fiber optic-linear array detection spectrophotometry (FO-LADS) and cloud point extraction (CPE) was developed using a cylindrical micro cell for simultaneous preconcentration and determination of different species. The CPE and FO-LADS methods have good matching conditions for combination because FO-LADS is suitable as a detection technique for the low volume of remained phase obtained after CPE. This combination was carried out using 50 μL cylindrical micro cell and then employed for simultaneous preconcentration and determination of cobalt and nickel.Cloud point extraction method was based on the chromogenic reaction of metal ions and 1-(2-pyridylazo)-2-naphthol (PAN) and then preconcentration of formed complexes using octylphenoxypolyethoxyethanol (Triton X-114). The remained phase after CPE was transferred into cylindrical micro cell and located at the cell holder of FO-LADS. The spectra of cobalt and nickel complexes were collected by FO-LADS and processed for ordinary and first derivative spectrophotometry.Optimization of different parameters was evaluated. Under optimum conditions, calibration curves were linear in the range of 0.6-30.0 and 0.1-15.0 μg L⁻¹ with detection limits of 0.2 and 0.04 μg L⁻¹ for Co and Ni respectively. The relative standard deviations (R.S.D.s) were lower than 4%. The obtained enhancement factors were 198 and 199 for cobalt and nickel, respectively.The proposed method was compared with the other methods and applied to the analysis of several real and spiked samples.     

Species selective preconcentration and quantification of gold nanoparticles using cloud point extraction and electrothermal atomic absorption spectrometry

The determination of metallic nanoparticles in environmental samples requires sample pretreatment that ideally combines pre-concentration and species selectivity. With cloud point extraction (CPE) using the surfactant Triton X-114 we present a simple and cost effective separation technique that meets both criteria. Effective separation of ionic gold species and Au nanoparticles (Au-NPs) is achieved by using sodium thiosulphate as a complexing agent. The extraction efficiency for Au-NP ranged from 1.01 ± 0.06 (particle size 2 nm) to 0.52 ± 0.16 (particle size 150 nm). An enrichment factor of 80 and a low limit of detection of 5 ng L⁻¹ is achieved using electrothermal atomic absorption spectrometry (ET-AAS) for quantification. TEM measurements showed that the particle size is not affected by the CPE process. Natural organic matter (NOM) is tolerated up to a concentration of 10 mg L⁻¹. The precision of the method expressed as the standard deviation of 12 replicates at an Au-NP concentration of 100 ng L⁻¹ is 9.5%. A relation between particle concentration and the extraction efficiency was not observed. Spiking experiments showed a recovery higher than 91% for environmental water samples.     

Determination of lead in water samples by graphite furnace atomic absorption spectrometry after cloud point extraction

Cloud point extraction (CPE) has been used for the pre-concentration of lead, after the formation of a complex with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (5-Br-PADAP), and later analysis by graphite furnace atomic absorption spectrometry (GFAAS) using octylphenoxypolyethoxyethanol (TritonX-114) as surfactant. The chemical variables affecting the separation phase were optimized. Separation of the two phases was accomplished by centrifugation for 15 min at 4000 rpm. Under the optimum conditions i.e., pH 8.0, cloud point temperature 40 °C, [5-Br-PADAP] = 2.5 × 10⁻⁵ mol l⁻¹, [Triton X-114] = 0.05%, added methanol volume = 0.15 ml, pre-concentration of only 10 ml sample permitted an enhancement factor of 50-fold. The lower limit of detection (LOD) obtained under the optimal conditions was 0.08 μg l⁻¹. The precision for 10 replicate determinations at 5 μg l⁻¹ Pb was 2.8% relative standard deviation (R.S.D.). The calibration graph using the pre-concentration system for lead was linear with a correlation coefficient of 0.9984 at levels near the detection limits up to at least 30 μg l⁻¹. The method was successfully applied to the determination of lead in water samples.     

Ultratrace determination of cadmium by cold vapor atomic absorption spectrometry after preconcentration with a simplified cloud point extraction methodology

A simplified micelle-mediated extraction methodology for the preconcentration of ultratrace levels of cadmium as a prior step to its determination by cold vapor atomic absorption spectrometry (CV-AAS) has been developed. The methodology is based on the cloud point extraction (CPE) of cadmium at pH 8 by using the non-ionic surfactant polyethyleneglycolmono-p-nonylphenylether (PONPE 7.5) without adding any chelating agent. Cadmium cold vapor was generated from 2 ml of the extracted surfactant-rich phase by means of sodium tetrahydroborate (3%, w/v) as a reducing agent and hydrochloric acid (0.2 mol l⁻¹) as a carrier solution. Several important variables that affect the cloud point extraction and cold vapor cadmium generation efficiency were investigated and optimized. The preconcentration of only 50 ml of solution in the presence of 0.06% (v/v) PONPE 7.5 gives an enhancement factor of 62. The calibration graph using the preconcentration system was linear in the range of 4-100 ng l⁻¹ with a correlation coefficient of 0.9992. Detection limit (3 s) obtained in the optimal conditions was 0.56 ng l⁻¹. The relative standard deviation (R.S.D.) for six replicate determinations at 20 ng l⁻¹ Cd level was 3.2%. The proposed method was successfully applied to the ultratrace determination of cadmium in water samples.     

Development of a cloud point extraction and preconcentration method for silver prior to flame atomic absorption spectrometry

The possibility was investigated of using 2-mercaptobenzothiazole (MBT) for Ag(I) concentration by micellar extraction at cloud point (CP) temperature and subsequent determination by flame atomic absorption spectrometry (FAAS). The method is based on the complexation of Ag(I) with 2-mercaptobenzothiazole (MBT) in the presence of non-ionic micelles of Triton X-114. The effect of experimental conditions such as pH, concentration of chelating agent and surfactant, equilibration temperature and time on cloud point extraction was studied. Under the optimum conditions, the preconcentration of 10 mL of water sample in the presence of 0.1% Triton X-114 and 2 × 10⁻⁴ mol L⁻¹ 2-mercaptobenzothiazole permitted the detection of 2.2 ng mL⁻¹ silver. The calibration graph was linear in the range of 10–200 ng mL⁻¹, and the recovery of more than 99% was achieved. The proposed method was used in FAAS determination of Ag(I) in water samples.     

A cloud point extraction approach using Triton X-100 for the separation and preconcentration of Sudan dyes in chilli powder

A CPE-HPLC (UV) method was developed for the determination of Sudan (I-IV) dyes, non-ionic surfactant Triton X-100 was used to extract and preconcentrate Sudan dyes from chilli powder prior to their determination by HPLC-UV. The separation and determination of Sudan dyes was then carried out in the HPLC-UV system with isocratic elution, and the detector was set at 500 nm. The parameters and variables that affect the extraction were investigated. Under optimum conditions: 3% of Triton X-100 (W/V), 10% of Na₂CO₃ (W/V), heat-assisted at 70 °C for 30 min. Recoveries of the Sudan dyes ranged from 80.70% to 85.45% in chilli powder by CPE method, with all the relative standard deviations of less than 3%. Limit of detection (LOD) and limit of quantification (LOQ) were in the range of 2.0-4.0 and 7.0-12.0 μg kg⁻¹ in chilli powder, respectively.     

Determination of copper in water samples by atomic absorption spectrometry after cloud point extraction

Cloud point extraction employing the new reagent 6-[2′-(6′-methyl-benzothiazolylazo)]-1,2-dihydroxy-3,5-benzenedisulfonic acid as complexing agent and Triton X-114 as the surfactant is proposed for copper determination. A sample volume of 10 mL was used. Dilution of the surfactant-rich phase with acidified methanol was performed after phase separation, and the copper contents were measured by flame atomic absorption spectrometry. Variables affecting the system were optimized using factorial design and Doehlert matrix. Signals were measured as peak height using an instrument software. Using the experimental conditions defined in the optimization, the method allowed copper determination with a detection limit of 1.5 μg L⁻¹. The calculated enrichment factor is 14. The effects of foreign ions are reported. The accuracy of the procedure was tested by analyzing certified reference material. The method was successfully applied to copper determination in natural and drinking water samples.     

Determination of estrogens in water by HPLC-UV using cloud point extraction

A method based on cloud point extraction was developed to determine four kinds of estrogens: estriol (E3), estradiol (E2), estrone (E1), and progesterone (P) in water by high performance liquid chromatography separation and ultraviolet detection (HPLC-UV). The non-ionic surfactant Triton X-114 was chosen as extractant solvent. The parameters affecting extraction efficiency, such as concentrations of Triton X-114 and Na₂SO₄, equilibration temperature, equilibration time and centrifugation time were evaluated and optimized. Under the optimum conditions, preconcentration factors of 99 for E3, 73 for E2, 152 for E1 and 86 for P were obtained for 10 mL water sample. The detection of limitation was 0.23 ng mL⁻¹ for E3, 0.32 ng mL⁻¹ for E2, 0.25 ng mL⁻¹ for E1 and 5.0 ng mL⁻¹ for P. The proposed method was successfully applied to the determination of trace amount of estrogens in wastewater treatment plant (WWTP) effluent water and exposure water with 10 ng mL⁻¹ E2 for toxicological study in our lab. For the case of WWTP effluent water samples, no estrogen was found. The accuracy of the proposed method was tested by recovery measurements of spiked samples and good recoveries of 81.2-99.5% were obtained.     

Acid extraction and cloud point preconcentration as sample preparation strategies for cobalt determination in biological materials by thermospray flame furnace atomic absorption spectrometry

A thermospray flame furnace atomic absorption spectrometer (TS-FF-AAS) was employed for Co determination in biological materials. Cobalt presents a high atomization temperature and consequently poor sensitivity is obtained without changing its thermochemical behavior. The effect of different complexing agents on sensitivity was evaluated based on the formation of Co volatile compounds. A cloud point procedure was optimized for Co preconcentration for further improvement of sensitivity. Samples were treated with 1 mol l^− 1 hydrochloric acid solution for quantitative extraction of Co without simultaneous extraction of Fe, since it is a strong interferent. After the extraction and preconcentration steps, a sample volume of 150 μl was introduced into the hot Ni tube using air as carrier at a flow-rate of 0.4 ml min^− 1. The best sensitivity was attained using ammonium pyrrolidinedithiocarbamate (APDC) and Triton X-114 was employed for implementation of the cloud point procedure. The detection limit obtained for Co was 2.1 μg l^− 1 and the standard deviation was 5.8% for a solution containing 100 μg l^− 1 (n = 10). Accuracy was checked using two certified reference materials (tomato leaves and bovine liver) and results were in agreement with certified values at a 95% confidence level. Employing the developed procedure, Co were quantified in different biological materials (plant and animal tissues). The proposed method presents suitable sensitivity for cobalt determination in the quality control of foods.     

Selective extraction and preconcentration of cerium(IV) in water samples by cloud point extraction and determination by inductively coupled plasma optical emission spectrometry

Cloud point extraction (CPE) was used for the selective extraction and separation of cerium(IV) from aqueous solutions. The method is based on the formation of cerium(IV)-n-p-tolylbenzohydroxamic acid (n-TBHA) complex that is extracted into the micellar phase (Triton X-114) at a temperature above the cloud point temperature (CPT). After phase separation, the surfactant rich phase was diluted up to 1.0 mL and determined by inductively coupled plasma-optical emission spectrometry (ICP-OES). Under the optimum extraction conditions and instrument parameters, by preconcentration of only 10.0 mL of sample in the presence of 0.09% Triton X-114, an enhancement factor of 13.8 was obtained. The analytical curve was linear in the range of 1.5–1200 μg L⁻¹ and the detection limit was 0.4 μg L⁻¹. The method was applied to the determination of Ce(IV) in water samples with satisfactory results.     

Cloud point formation based on mixed micelles in the presence of electrolytes for cobalt extraction and preconcentration

A new micelle-mediated phase separation of metal ions, applied for preconcentrating trace levels of cobalt as a prior step to its determination by flame atomic spectroscopy, has been developed. Two methods were proposed employing both Triton X-100 and sodium dodecyl sulfate (SDS) as a mixed micellar system while the phase separation was induced by HCl or NaCl addition. Cobalt was complexed with pyridylazo compounds (PAN, PAR, 5-Br-PADAP) in an aqueous surfactant medium and it was concentrated in the surfactant rich phase after phase separation. The chemical variables affecting the cloud point extraction were evaluated, optimized and successfully applied to cobalt determination in pharmaceutical samples. Under the optimized conditions, the preconcentration system permitted limits of detection as 1.1 and 1.6 μg l⁻¹ cobalt, respectively, when HCl and NaCl were used. Both proposed methods showed linear calibration within a 25-200 μg l⁻¹ cobalt range. The extraction efficiency was investigated at different cobalt concentrations (40-185 μg l⁻¹) and good recoveries (98-102%) were obtained by using NaCl as electrolyte. The results obtained were compared with those observed with ET AAS.     

Laser induced thermal lens spectrometry for cobalt determination after cloud point extraction

A new approach, employing cloud point extraction (CPE) in combination with thermal lens spectrometry (TLS), has been developed for the determination of cobalt. The CPE and TLS methods have good matching conditions for combination because TLS is suitable for low volume samples obtained after CPE and for organic solvents, which are used for dissolving the remaining analyte phase.1-(2-Pyridylazo)-2-naphthol (PAN) was used as a complexing agent and octylphenoxypolyethoxyethanol (Triton X-114) was added as a surfactant; then the pH of solution was adjusted. After phase separation at 50 °C based on the cloud point extraction of the mixture, the surfactant-rich phase was dried and the remaining phase was dissolved using 20 μL of carbon tetrachloride. The obtained solution was introduced into the quartz micro cell and the analyte was determined by thermal lens spectrometry. The He-Ne laser (632.8 nm) was used as both the probe and the excite source.Under optimum conditions, the analytical curve was linear for the concentration range of 0.2-40 ng mL⁻¹ and the detection limit was 0.03 ng mL⁻¹. The enhancement factor of 470 was achieved for a 10 mL sample. Relative standard deviations were lower than 5%.The method was successfully applied to the extraction and determination of cobalt in tap, river and sea water.