Development of HPLC-MS/MS method for the simultaneous determination of environmental phenols in human urine

We present a sensitive method for simultaneous determination of bisphenol A (BPA), benzophenone-3 (BP-3), 4-tert-octylphenol (t-OP), ortho-phenylphenol (OPP), four parabens (methyl, ethyl, propyl, butyl parabens) and five chlorophenols (2,4-dichlorophenol (2,4-DCP), 2,5-dichlorophenol (2,5-DCP), 2,4,5-trichlorophenol (2,4,5-triclorophenol), 2,4,6-trichlorophenol (2,4,6-TCP), and triclosan (TCS)), in human urine by high-pressure liquid chromatography (HPLC) mass spectrometry (MS). Samples were processed using enzymatic deconjugation of glucuronides followed by solid phase extraction (SPE) on a C18 cartridge and the eluate was concentrated. Analytes were separated by reversed-phase HPLC and then detected by atmospheric pressure chemical ionisation (APCI) MS and quantified by isotope dilution method. We describe details for optimisation of each step of the procedure. The sample treatment steps are straightforward and not labour-intensive and, therefore, permit a high sample throughput with excellent prospects for automation. This method shows low inter-day variation, and detection limits for most of the compounds are below 1 ng/mL in 1 mL of urine. The method accuracy was also verified by the analysis of proficiency testing urine samples.     

Quantification of urinary conjugates of bisphenol A, 2,5-dichlorophenol,and 2-hydroxy-4-methoxybenzophenone in humans by online solid phase extraction–high performance liquid chromatography–tandem mass spectrometry

Urinary concentrations of phenols or their metabolites have been used as biomarkers to assess the prevalence of exposure to these compounds in the general population. Total urinary concentrations, which include both free and conjugated (glucuronide and sulfated) forms of the compounds, are usually reported. From a toxicologic standpoint, the relative concentrations of the free species compared with their conjugated analogs can be important because conjugation may reduce the potential biologic activity of the phenols. In this study, we determined the percentage of glucuronide and sulfate conjugates of three phenolic compounds, bisphenol A (BPA), 2,5-dichlorophenol (2,5-DCP), and 2-hydroxy-4-methoxybenzophenone (benzophenone-3, BP-3) in 30 urine samples collected between 2000 and 2004 from a demographically diverse group of anonymous adult volunteers. We used a sensitive on-line solid phase extraction–isotope dilution–high performance liquid chromatography–tandem mass spectrometry method. These three phenols were detected frequently in the urine samples tested. Only small percentages of the compounds (9.5% for BPA, and 3% for 2,5-DCP and BP-3) were excreted in their free form. The percentage of the sulfate conjugate was about twice that of the free compound. The glucuronide conjugate was the major metabolite, representing 69.5% (BPA), 89% (2,5-DCP), and 84.6% (BP-3) of the total amount excreted in urine. These results are in agreement with those reported before which suggested that BPA-glucuronide was an important BPA urinary metabolite in humans. To our knowledge, this is the first study describing the distribution of urinary conjugates of BP-3 and 2,5-DCP in humans.     

Synthetic approaches to parabens molecularly imprinted polymers and their applications to the solid-phase extraction of river water samples

In this paper we describe the synthesis, characterisation and use of two distinct molecularly imprinted polymers (MIPs) prepared using esters of p-hydroxybenzoic acid (parabens) as templates: one MIP was synthesised by precipitation polymerisation using a semi-covalent molecularly imprinting strategy with methyl paraben as the template/target (MIP 1); the second MIP was prepared in monolithic form through a conventional non-covalent molecular imprinting strategy, with butyl paraben as the template (MIP 2). MIP 1 recognized methyl paraben, showed cross-selectivity for other parabens analytes used in the study and higher affinity towards these compounds than did a non-imprinted control polymer. Similarly, MIP 2 demonstrated higher affinity towards paraben analytes than a non-imprinted control polymer.For the analysis of environmental water samples, a solid-phase extraction (SPE) protocol was developed using MIP 2 as sorbent, and results were compared to a SPE using a commercial sorbent (Oasis HLB). With MIP 2 as sorbent and butyl paraben as target, when percolating 500 mL of river water spiked at 1 μg L⁻¹ through the SPE cartridge, and using 1 mL of isopropanol as cleaning solvent, a higher recovery of butyl 4-hydroxybenzoate (butyl paraben) and a cleaner chromatogram where achievable when using the MIP compared to the commercial sorbent.     

Selective molecularly imprinted polymer combined with restricted access material for in-tube SPME/UHPLC-MS/MS of parabens in breast milk samples

A new molecularly imprinted polymer modified with restricted access material (a hydrophilic external layer), (MIP-RAM) was synthesized via polymerization in situ in an open fused silica capillary. This stationary phase was used as sorbent for in-tube solid phase microextraction (in-tube SPME) to determine parabens in breast milk samples by ultra-high-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). Scanning electron micrographs (SEM) illustrate MIP surface modification after glycerol dimethacrylate (hydrophilic monomer) incorporation. The interaction between parabens and MIP-RAM was investigated by Fourier-transform infrared (FTIR) spectroscopy. The Scatchard plot for MIP-RAM presented two linear parts with different slopes, illustrating binding sites with high- and low-affinity. Endogenous compounds exclusion from the MIP-RAM capillary was demonstrated by in-tube SPME/LC-UV assays carried out with blank milk samples. The in-tube SPME/UHPLC-MS/MS method presented linear range from 10 ng mL⁻¹ (LLOQ) to 400 ng mL⁻¹ with coefficients of determination higher than 0.99, inter-assay precision with coefficient of variation (CV) values ranging from 2 to 15%, and inter-assay accuracy with relative standard deviation (RSD) values ranging from −1% to 19%. Analytical validation parameters attested that in-tube SPME/UHPLC-MS/MS is an appropriate method to determine parabens in human milk samples to assess human exposure to these compounds. Analysis of breast milk samples from lactating women demonstrated that the proposed method is effective.     

Automated on-line column-switching HPLC-MS/MS method for measuring environmental phenols and parabens in serum

We developed a method using on-line solid phase extraction (SPE) coupled to high performance liquid chromatography–isotope dilution tandem mass spectrometry (HPLC–MS/MS) to measure the serum concentrations of seven environmental phenols and five parabens: bisphenol A; ortho-phenylphenol; 2,4-dichlorophenol; 2,5-dichlorophenol; 2,4,5-trichlorophenol; benzophenone-3; triclosan; and methyl-, ethyl-, propyl-, butyl-, and benzyl-parabens. The phenols and parabens present in serum were retained and concentrated on a C18 reversed-phase size-exclusion SPE column, back-eluted from the SPE column while the eluate was diluted through a mixing Tee (analyte peak focusing), separated using a pair of monolithic HPLC columns, and detected by isotope dilution-MS/MS. Sample preparation did not require protein precipitation, only dilution of the serum with 0.1 M formic acid. This method, which combines an on-line SPE with analyte peak focusing feature and the selective atmospheric pressure photoionization MS detection, resulted in limits of detection ranging from 0.1 to 0.5 ng/mL for most of the analytes. The high throughput and adequate sensitivity with yet a relative low serum volume used (100 μL) confirm that analytically it is possible to measure simultaneously these phenols and parabens with the precision and accuracy at sub-parts-per-billion levels required for biomonitoring. However, important additional factors, including validated sample collecting, handling, and storing protocols, as well as toxicokinetic data, are required if these measures are used for exposure assessment.     

Fully automated determination of parabens, triclosan and methyl triclosan in wastewater by microextraction by packed sorbents and gas chromatography-mass spectrometry

A fully automated method for the determination of triclosan (TCS), its derivative methyl triclosan (MeTCS) and six parabens (esters of 4-hydroxybenzoic acid) including branched and linear isomers of propyl (i-PrP and n-PrP) and butyl paraben (i-BuP and n-BuP) in sewage water samples is presented. The procedure includes analytes enrichment by microextraction by packed sorbent (MEPS) coupled at-line to large volume injection-gas chromatography-mass spectrometry (LVI-GC-MS). Under optimised conditions, compounds were extracted from 2 mL samples, adjusted at pH 3, using a C18 MEPS-sorbent. Adsorbed analytes were eluted directly into the Programmable Temperature Vaporizer (PTV) injector of the chromatograph with 2×25 μL of ethyl acetate. They were quantified using standard solutions in ultrapure water submitted to the same sample enrichment process as real sewage water samples. After signal normalisation using isotopic labelled species as internal surrogates, no differences were noticed among the extraction efficiency for sewage and ultrapure water; moreover, the proposed method reported lineal calibration curves from 0.1 to 10 ng mL(-1), relative standard deviations (%RSD) between 2 and 7.1% and limits of detection (LODs) varying from 0.001 to 0.015 ng mL(-1) in ultrapure water and from 0.02 to 0.59 ng mL(-1) in the most complex sample (raw wastewater).     

Determination of parabens in house dust by pressurised hot water extraction followed by stir bar sorptive extraction and thermal desorption-gas chromatography-mass spectrometry

This study describes the development of a new method for determining p-hydroxybenzoic esters (parabens) in house dust. This optimised method was based on the pressurised hot water extraction (PHWE) of house dust, followed by the acetylation of the extracted parabens, stir bar sorptive extraction (SBSE) with a polydimethylsiloxane stir bar, and finally analysis using thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS). The combination of SBSE and PHWE allows the analytes to be preconcentrated and extracted from the aqueous extract in a single step with minimal manipulation of the sample. Furthermore the in situ acetylation of parabens prior to SBSE improved their extraction efficiency and their GC-MS signal. The method showed recoveries of between 40 and 80%, good linearity, repeatability and reproducibility (<10% RSD, at 100 ng g(-1), n=5), low limits of detection (from 1.0 ng g(-1) for propyl paraben to 2.1 ng g(-1) for methyl paraben) and quantification (from 3.3 ng g(-1) for propyl paraben to 8.5 ng g(-1) for methyl paraben). The proposed method was applied to the analysis of house dust samples. All the target parabens were found in the samples. Methyl and propyl parabens were the most abundant, with concentrations up to 2440 ng g(-1) and 910 ng g(-1), respectively. The high levels of parabens found in the samples confirm the importance of determining organic contaminants in indoor environments.     

Stir bar sorptive extraction of parabens, triclosan and methyl triclosan from soil, sediment and sludge with in situ derivatization and determination by gas chromatography-mass spectrometry

The aim of this research work was the evaluation of stir-bar sorptive extraction (SBSE) in combination with an in situ derivatization to determine parabens (methylparaben, isopropylparaben, n-propylparaben, butylparaben and benzylparaben), triclosan and methyltriclosan in soil samples. This is the first time that this approach has been applied to the determination of these compounds in soil samples, providing important advantages over conventional extraction techniques, such as minimization of sampling handling, complete elimination of the use of organic solvents and simplification of the analytical procedure with reduced time consumption. The enriched target analytes were desorbed thermally using a thermodesorption system coupled to a gas chromatograph and a mass spectrometer. The optimized derivatization and SBSE extraction conditions, as well as the analytical characteristics of the method were obtained using spiked soil samples. The proposed methodology proved to be easy to use and sensitive, with limits of detection between 80 ng/kg and 1.06 μg/kg, and reproducibility values below 13%. The accuracy of the method was evaluated at two concentration levels, obtaining apparent recoveries between 91% and 110%. The matrix composition significantly influenced the extraction procedure, and a need to adopt a standard additions protocol is apparent. The analytes assayed were determined successfully in different environmental soil samples.     

Molecularly imprinted polymer for the extraction of parabens from environmental solid samples prior to their determination by high performance liquid chromatography-ultraviolet detection

An analytical methodology incorporating a molecularly imprinted solid-phase extraction procedure (MISPE) has been developed for the determination of parabens in environmental solid samples. Four different polymers were prepared combining the use of acetonitrile or toluene as porogen, and 4-vinylpyridine (VP) or methacrylic acid (MAA) as monomer, using benzylparaben (BzP) as a template molecule. Although all the polymers were able to recognize the template in rebinding experiments, the MIP prepared in toluene using MAA showed better performance. This polymer was also capable of recognizing other parabens (methyl, ethyl, isopropyl, propyl, isobutyl, butyl and benzylparaben) allowing to develop an appropriated MISPE procedure for this family of compounds. The extraction of the parabens from environmental solid samples was performed by ultrasonic assisted extraction in small columns (SAESC), and this procedure next to MISPE as clean-up step followed by HPLC-UV determination was successfully used for the determination of parabens in soil and sediment samples of different locations. Recoveries ranging from 80% to 90% have been achieved depending on the compound and the samples, and limits of detection (LODs) were under 1 ng g⁻¹ for all the compounds, making this method suitable for the determination of parabens in environmental solid matrices. The method was further applied to the determination of paraben contents in real samples, founding levels up to 11.5 ng g⁻¹ in sea sediments.     

Simultaneous determination of parabens,triclosan and triclocarban in water by liquid chromatography/electrospray ionisation tandem mass spectrometry

A method for the determination of several household biocides in water by liquid chromatography/electrospray ionisation tandem mass spectrometry (LC/ESI‐MS/MS) is presented. It permits the simultaneous determination of triclosan (TCS), triclocarban (TCC) and seven parabens, including the distinction between branched and linear isomers of propyl (i‐PrP and n‐PrP) and butyl parabens (i‐BuP and n‐BuP). Prior to LC/MS/MS, analytes are preconcentrated by solid‐phase extraction (SPE) on Oasis HLB (60 mg) cartridges at natural sample pH and subsequently eluted with 4 mL of methanol. This simple SPE procedure provides extraction recoveries above 85% except for raw wastewater, where it falls to 65% for TCC. The performance of the method was tested with two triple‐quadrupole LC/MS instruments from a low/mid and mid/high market range: a Varian 1200L and an API‐4000. The latter system provided between 3 and 80 times lower limits of quantification (LOQs) than the first one, in the 0.08–0.44 ng/L range for surface water. Moreover, a comparison of matrix effects on both instruments showed a very different behaviour, particularly in the case of parabens. For these compounds signal suppression was observed in the 1200L instrument and signal enhancement with the 4000 instrument. As a result, different calibration approaches were chosen for them and this pointed to the need of matrix effect re‐evaluation in method transfer between different LC/MS systems. The application of the method to real samples showed the ubiquity of methyl paraben (MeP) and n‐PrP (at the 1–6 µg/L in raw wastewater) and the coexistence of i‐BuP and n‐BuP at similar levels (ca. 100–200 ng/L in raw wastewater). Copyright © 2009 John Wiley & Sons, Ltd.     

Aquatic degradation of triclosan and formation of toxic chlorophenols in presence of low concentrations of free chlorine

The degradation of 2-(2,4-dichlorophenoxy)-5-chlorophenol (triclosan) in chlorinated water samples was investigated. Sensitive determination of the parent compound and its transformation products was achieved by gas chromatography with mass spectrometry detection after sample concentration, using a solid-phase extraction sorbent and silylation of the target compounds. Experiments were accomplished using ultrapure water spiked with chlorine and triclosan concentrations in the low mg/l and ng/ml ranges respectively. Chlorination of the phenolic ring and cleavage of the ether bond were identified as the main triclosan degradation pathways. Both processes led to the production of two tetra- and a penta-chlorinated hydroxylated diphenyl ether, as well as 2,4-dichlorophenol. The formation of 2,3,4-trichlorophenol was not detected in any experiment; however, significant amounts of 2,4,6-trichlorophenol were noticed. All of these five compounds were also identified when triclosan was added to tap-water samples with free chlorine concentrations below 1 mg/l. Minor amounts of three di-hydroxylated phenols, containing from one to three atoms of chlorine in their structures, were also identified as unstable triclosan chlorination by-products. The analysis of several raw wastewater samples showed the co-existence of important concentrations of triclosan and its most stable by-products (2,4-dichlorophenol and 2,4,6-trichlorophenol), reinforcing the potential occurrence of the described transformations when products containing triclosan are mixed with chlorinated tap water.     

Simultaneous determination of bisphenols,benzophenones and parabens in human urine by using UHPLC-TQMS

An analytical method for the simultaneous determination of six bisphenols, five benzophenones and seven parabens by using ultra-high performance liquid chromatography coupled with triple quadrupole mass spectrometry was developed and applied for human urine sample analysis.     

Determination of endocrine-disrupting phenols, acidic pharmaceuticals, and personal-care products in sewage by solid-phase extraction and gas chromatography-mass spectrometry

The occurrence, fate, and effects of phenols with endocrine-disrupting properties as well as some pharmaceuticals and personal-care products in the environment have frequently been discussed in recent literature. In many cases, these compounds were determined by using individual methods which can be time-consuming if results for multiple parameters are required. Using a solid-phase extraction procedure with an anion exchanger in this work, we have developed and optimized a multi-residue method for the extraction of 21 phenols and acids in sewage influent and effluent. The phenols and acids were then selectively eluted in separate fractions and were converted into pentafluoropropionyl (PFP) and tert-butyldimethylsilyl (TBDMS) derivatives, respectively, for gas chromatography-mass spectrometric (GC/MS) determination. When applied to the sewage samples under study, the results for nonylphenol, bisphenol A (BPA), triclosan (TCS), 17ss-estradiol (E2), estrone (E1), salicylic acid, ibuprofen, naproxen, diclofenac, and a few other acidic drugs were consistent with those determined previously by individual methods. Using the same procedure, we also report, for the first time, the occurrence of 2-phenylphenol and parabens in those sewage samples.     

固相萃取-微乳液相色谱法测定环境水体中的3种酚类化合物

建立了固相萃取-微乳液相色谱法同时测定环境水体中的苯酚、双酚A (BPA)、2,4-二氯苯酚3种酚类化合物的检测方法。水样加酸酸化后,经C18固相萃取小柱富集净化,用微乳液相色谱法测定3种目标物的含量。在Inertsil C18色谱柱(150 mm×4.6 mm, 5 μm)上以微乳(3.0%十二烷基硫酸钠(SDS)-6.0%正丁醇-0.8%正庚烷-90.2%(水+0.5%HAc))和乙腈作为流动相进行梯度洗脱,流速1.0 mL/min,检测波长280 nm。结果表明,苯酚、双酚A、2,4-二氯苯酚的检出限(S/N=3)依次为0.74、8.0、8.0 μg/L,线性范围在0.1~10 mg/L范围内,相关系数(r)均大于0.999。将3种酚类化合物定量加到空白水样中,苯酚、双酚A、2,4-二氯苯酚的加标回收率分别为82.7%、87.8%、82.6%,其RSD均小于5%(n=6)。对环境水样的酚类化合物分析也取得了良好的加标回收率,其值均在85.7%~113.2%之间。结果表明,该方法准确可靠、灵敏度高,适用于环境水体中酚类化合物的检测。     

共价有机框架材料磁固相萃取-高效液相色谱法分析环境水体中对羟基苯甲酸酯

建立了一种基于共价有机框架材料的磁固相萃取-高效液相色谱方法,用于环境水样中对羟基苯甲酸酯的快速灵敏分析。首先以Fe₃O₄纳米粒子为磁核,通过1,3,5-苯三甲醛(Tb)和联苯胺(Bd)在室温下的席夫碱反应合成了磁性共价有机框架材料——Fe₃O₄@TbBd,通过扫描电镜、热重分析、X射线衍射和振动样品磁强计等表征手段证明了该磁性共价有机框架材料具有良好的热稳定性和化学稳定性,且磁响应强度较大,是用于磁固相萃取的理想材料。随后系统研究了影响萃取效率的因素,包括吸附剂用量、萃取时间、pH、解吸溶剂、解吸时间和解吸次数,建立了基于Fe₃O₄@TbBd的磁固相萃取-高效液相色谱测定环境水样中4种对羟基苯甲酸酯的方法。方法的线性范围良好,4种目标物的检出限和定量限范围分别为0.2~0.4 μg/L和0.7~1.4 μg/L,加标回收率为86.1%~110.8%,日内和日间精密度的相对标准偏差(RSD)分别低于5.5%和4.9%。最后将该方法应用于东湖水、长江水和生活废水中对羟基苯甲酸酯的测定,不同加标水平下对羟基苯甲酸酯的回收率在80.7%~117.5%之间,RSD在0.2%~8.8%之间。该方法操作简单,萃取时间短,灵敏度较高且对环境友好,在环境水样中对羟基苯甲酸酯的检测方面有良好的应用潜力。     

Fabric phase sorptive extraction/GC‐MS method for rapid determination of broad polarity spectrum multi‐class emerging pollutants in various aqueous samples

A rapid extraction and cleanup method using selective fabric phase sorptive extraction combined with gas chromatography and mass spectrometry has been developed and validated for the determination of broad polarity spectrum emerging pollutants, ethyl paraben, butyl paraben, diethyl phthalate, dibutyl phthalate, lidocaine, prilocaine, triclosan, and bisphenol A in various aqueous samples. Some important parameters of fabric phase sorptive extraction such as extraction time, matrix pH, stirring speed, type and volume of desorption solvent were investigated and optimized. Calibration curves were obtained in the concentration range 0.05–500 ng/mL. Under the optimum conditions, the limits of detection were in the range 0.009 –0.021 ng/mL. This method was validated by analyzing the compounds in spiked aqueous samples at different levels with recoveries of 93 to 99% and relative standard deviations of <6%. The developed method was applied for the determination of the emerging contaminants in tap water, municipal water, ground water, sewage water, and sludge water samples. The results demonstrate that fabric phase sorptive extraction has great potential in the preconcentration of trace analytes in complex matrix.     

Miniaturized matrix solid‐phase dispersion coupled with supramolecular solvent‐based microextraction for the determination of paraben preservatives in cream samples

An analytical method is presented for the determination of paraben preservatives in semisolid cream samples by matrix solid‐phase dispersion combined with supramolecular solvent‐based microextraction. Due to the oily and sticky nature of the sample matrix, parabens were first extracted from the samples by matrix solid‐phase dispersion using silica as sorbent material with a clean‐up performed with tetrahydrofuran in the elution step. The eluate (500 μL), 1‐decanol (120 μL), and water (4.4 mL) were then mixed in a polyethylene pipette to form supramolecular solvent. Finally, the analytes in the supramolecular solvent were separated and determined by liquid chromatography with ultraviolet detection. Under optimal extraction conditions, the extraction recoveries of the studied compounds were obtained in the range of 63–83%. The limits of detection for the analytes were between 0.03 and 0.04 μg/g. The precision of the method varied between 4.0–6.7 (intraday) and 6.2–7.9% (interday). Finally, the optimized procedure was applied to the determination of the target preservatives in a variety of cream samples (diaper rash, skin allergy, face and hand moisturizing) with satisfactory recoveries (86–102%).     

GC-MS determination of parabens,triclosan and methyl triclosan in water by in situ derivatisation and stir-bar sorptive extraction

Stir-bar sorptive extraction in combination with an in situ derivatisation reaction and thermal desorption–gas chromatography–mass spectrometry was successfully applied to determine parabens (methylparaben, isopropylparaben, n-propylparaben, butylparaben and benzylparaben), triclosan and methyltriclosan in water samples. This approach improves both the extraction efficiency and the sensitivity in the GC in a simple way since the derivatisation reaction occurs at the same time as the extraction procedure. The in situ derivatisation reaction was carried out with acetic anhydride under alkaline conditions. Thermal desorption parameters (cryofocusing temperature, desorption flow, desorption time, desorption temperature) were optimised using a Box–Behnken experimental design. All the analytes gave recoveries higher than 79%, except methylparaben (22%). The method afforded detection limits between 0.64 and 4.12 ng/L, with good reproducibility and accuracy values. The feasibility of the method for the determination of analytes in water samples was checked in tap water and untreated and treated wastewater.     

On-line solid-phase microextraction of triclosan, bisphenol A, chlorophenols, and selected pharmaceuticals in environmental water samples by high-performance liquid chromatography–ultraviolet detection

A method using on-line solid-phase microextraction (SPME) on a carbowax-templated fiber followed by liquid chromatography (LC) with ultraviolet (UV) detection was developed for the determination of triclosan in environmental water samples. Along with triclosan, other selected phenolic compounds, bisphenol A, and acidic pharmaceuticals were studied. Previous SPME/LC or stir-bar sorptive extraction/LC-UV for polar analytes showed lack of sensitivity. In this study, the calculated octanol–water distribution coefficient (log D) values of the target analytes at different pH values were used to estimate polarity of the analytes. The lack of sensitivity observed in earlier studies is identified as a lack of desorption by strong polar–polar interactions between analyte and solid-phase. Calculated log D values were useful to understand or predict the interaction between analyte and solid phase. Under the optimized conditions, the method detection limit of selected analytes by using on-line SPME-LC-UV method ranged from 5 to 33 ng?L^?1, except for very polar 3-chlorophenol and 2,4-dichlorophenol which was obscured in wastewater samples by an interfering substance. This level of detection represented a remarkable improvement over the conventional existing methods. The on-line SPME-LC-UV method, which did not require derivatization of analytes, was applied to the determination of TCS including phenolic compounds and acidic pharmaceuticals in tap water and river water and municipal wastewater samples.

Optimization of solid-phase microextraction conditions for the determination of triclosan and possible related compounds in water samples

A solid-phase microextraction (SPME) method for the determination of triclosan, methyl triclosan, 2,4-dichlorophenol and 2,3,4-trichlorophenol (considered as possible triclosan metabolites) in water samples was optimised. Analytes were first concentrated on a SPME fibre, directly exposed to the sample, and then triclosan and the two chlorinated phenols on-fibre silylated using N-methyl-N-(tert.-butyldimethylsilyl)-trifluoroacetamide (MTBSTFA). Methyl triclosan remained unaffected during the derivatization step. Compounds were determined using gas chromatography in combination with mass spectrometry (GC-MS). Influence of different factors on the efficiency of extraction and derivatization steps was systematically investigated. Using a polyacrylate (PA) fibre quantification limits below 10 ng/l, and acceptable relative standard deviations, were obtained for all compounds after an extraction time of 30 min. On-fibre silylation was carried out in only 10 min. Moreover, the efficiency of the procedure was scarcely affected by the type of water sample. The method was applied to several samples of treated and raw wastewater, triclosan was found in all samples, at concentrations from 120 to 14,000 ng/l, and 2,4-dichlorophenol in most of them, at levels up to 2222 ng/l.