Photocatalytic performance of Ag doped SnO2 nanoparticles modified with curcumin

Visible light active Ag doped SnO₂ nanoparticles modified with curcumin (Cur–Ag–SnO₂) have been prepared by a combined precipitation and chemical impregnation route. The optical properties, phase structures and morphologies of the as-prepared nanoparticles were characterized using UV–visible diffuse reflectance spectra (UV–vis-DRS), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The surface area was measured by Brunauer. Emmett. Teller (B.E.T) analysis. Compared to bare SnO₂, the surface modified photocatalysts (Ag–SnO₂ and Cur–Ag–SnO₂) showed a red shift in the visible region. The photocatalytic activity was monitored via the degradation of rose bengal (RB) dye and the results revealed that Cur–Ag–SnO₂ shows better photocatalytic activity than that of Ag–SnO₂ and SnO₂. The superior photocatalytic activity of Cur–Ag–SnO₂ could be attributed to the effective electron-hole separation by surface modification. The effect of photocatalyst concentration, initial dye concentration and electron scavenger on the photocatalytic activity was examined in detail. Furthermore, the antifungal activity of the photocatalysts and the reusability of Cur–Ag–SnO₂ were tested.     

One‐Step SnO2 Nanotree Growth

A comparison between Au, TiO₂ and self‐catalysed growth of SnO₂ nanostructures using chemical vapour deposition is reported. TiO₂ enables growth of a nanonetwork of SnO₂, whereas self‐catalysed growth results in nanoclusters. Using Au catalyst, single‐crystalline SnO₂ nanowire trees can be grown in a one‐step process. Two types of trees are identified that differ in size, presence of a catalytic tip, and degree of branching. The growth mechanism of these nanotrees is based on branch‐splitting and self‐seeding by the catalytic tip, facilitating at least three levels of branching, namely trunk, branch and leaf.     

SnO2 /MWCNTs纳米复合材料的低热固相制备及其超电容特性研究

采用十二烷基三甲基溴化铵(DTAB)辅助固相法制备SnO2/MWCNTs纳米复合材料,X射线衍射(XRD)、透射电镜(TEM)测试表明,SnO2纳米颗粒均匀包裹在MWCNTs表面.循环伏安和恒流充放电测试表明,与SnO2颗粒和纯MWCNTs相比,SnO2/MWCNTs纳米复合材料在1.0 mol·L-1 Na2SO4电解液中的电化学电容性质得到明显改善.当SnO2质量分数为11%时,在电流密度0.2 A·g-1下,SnO2的电容值最大可达217.3 F·g-1.     

Land-ocean interaction in modern delta formation and development: A case study of the Pearl River delta,China

SnO₂ doped with La, Ce, Sm, Zn, Ca, Al and Sb was prepared by sol-gel technique and characterized by TEM, BET, XPS and XAES. The effect of the dopants on the grain sizes of SnO₂ was described and especially the effect of dopants on the distribution of the electronic state density (DESD) of Sn4d orbital was studied deeply by using X-ray-induced Auger electron spectroscopy (XAES). It was observed that the dopants could influence not only the grain sizes of SnO₂ but also electronic structure of SnO₂, as well as the stability of the doped SnO₂ samples. The experiment results indicated that the structure and stability of SnO₂ film could be improved by the chemical modification of the dopants.     

Land-ocean interaction in modern delta formation and development: A case study of the Pearl River delta,China

SnO₂ doped with La, Ce, Sm, Zn, Ca, Al and Sb was prepared by sol-gel technique and characterized by TEM, BET, XPS and XAES. The effect of the dopants on the grain sizes of SnO₂ was described and especially the effect of dopants on the distribution of the electronic state density (DESD) of Sn4d orbital was studied deeply by using X-ray-induced Auger electron spectroscopy (XAES). It was observed that the dopants could influence not only the grain sizes of SnO₂ but also electronic structure of SnO₂, as well as the stability of the doped SnO₂ samples. The experiment results indicated that the structure and stability of SnO₂ film could be improved by the chemical modification of the dopants.     

Photocatalytic decomposition of dyes using ZnO doped SnO2 nanoparticles prepared by solvothermal method

ZnO doped SnO₂ has been successfully synthesized by the solvothermal method using methanol as organic solvent. The effect of ZnO/SnO₂ molar ratios on the crystal structure, microstructure, optical and photocatalytic properties has been investigated. The synthesized samples are characterized by X-ray diffraction, transmission electron microscopy, N₂ physical adsorption, FT-IR spectroscopy and UV–Vis spectroscopy. XRD results revealed that all diffraction peaks positions agree well with the reflection of a tetragonal rutile structure of SnO₂ phase without extra peaks at 0.1ZnO:0.9SnO₂ and 0.2ZnO:0.8SnO₂ molar ratios. However, the secondary phase of ZnO at 0.3ZnO:0.7SnO₂ molar ratio was investigated. TEM images revealed that the shape of SnO₂ particles was spherical and the particle sizes of SnO₂ and 0.3ZnO:0.7SnO₂ molar ratio were 6.2 and 16.4 nm, respectively. The newly prepared samples have been tested by the determination of photocatalytic degradation of methylene blue (MB). The results indicated that Zn²⁺ doping at 0.3ZnO:0.7 SnO₂ molar ratio showed the highest photocatalytic activity for the MB photodegradation. The heightened photocatalytic activity of ZnO/SnO₂ could be ascribed to the enhanced charge separation derived from the coupling of ZnO with SnO₂ due to the potential energy differences between SnO₂ and ZnO. The recycling tests demonstrated that 0.3ZnO:0.7 SnO₂ photocatalysts were quite stable during that liquid–solid heterogeneous photocatalysis since no decrease in activity in the first four cycles was observed.     

Synthesis,Characterization and Photocatalytic Activity of Mg‐Impregnated ZnO–SnO2 Coupled Nanoparticles

ZnO–SnO₂ nanoparticles were prepared by coprecipitation method; then Mg, with different molar ratios and calcination temperatures, was loaded on the coupled nanoparticles by impregnation method. The synthesized nanoparticles were characterized by X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X‐ray spectroscopy (EDX), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS), and Brunauer–Emmett–Teller (BET) techniques. Based on XRD results, the ZnO–SnO₂ and Mg/ZnO–SnO₂ nanoparticles were made of ZnO and SnO₂ nanocrystallites. According to DRS spectra, the band gap energy value of 3.13 and 3.18 eV were obtained for ZnO–SnO₂ and Mg/ZnO–SnO₂ nanoparticles, respectively. BET analysis revealed a Type III isotherm with a microporous structure and surface area of 32.051 and 49.065 m² g^?1 for ZnO–SnO₂ and Mg/ZnO–SnO₂, respectively. Also, the spherical shape of nanocrystallites was deduced from TEM and FESEM images. The photocatalytic performance of pure ZnO–SnO₂ and Mg/ZnO–SnO₂ was analyzed in the photocatalytic removal of methyl orange (MO). The results indicated that Mg/ZnO–SnO₂ exhibited superior photocatalytic activity to bare ZnO–SnO₂ photocatalyst due to high surface area, increased MO adsorption and larger band gap energy. Maximum photocatalytic activity of Mg/ZnO–SnO₂ nanoparticles was obtained with 0.8 mol% Mg and calcination temperature of 350°C.     

SnO2 纳米棒的氧化还原特性

 利用室温固相反应在 NaCl-KCl 熔盐介质中, 通过焙烧含 SnO2 纳米颗粒前驱体合成了 SnO2 纳米棒, 并采用 X 射线衍射、扫描电镜、透射电镜、选区电子衍射和 X 射线光电子能谱对 SnO2 纳米棒进行了表征. 结果表明, SnO2 纳米棒是表面光滑、结晶完整的金红石结构单晶体, 直径为 10~20 nm, 长度为几百纳米到几个微米. 程序升温还原结果表明, SnO2 纳米棒具有较好的氧化还原性能和催化活性. 探讨了 SnO2 纳米棒的氧化还原机理.     

Size-controlled synthesis and characterization of quantum-size SnO2 nanocrystallites by a solvothermal route

By using ethylenediamine as both an alkali and ligand, quantum size SnO₂ nanocrystallites were synthesized with a solvothermal route. The transmission electron micrographs (TEM) were employed to characterize the morphologies of the products. The crystal sizes of the as-synthesized SnO₂ were ranged form 2.5 to 3.6 nm. The crystal structure and optical properties of the products were investigated by X-ray diffraction, Fourier transform infrared spectroscopy, optical absorption spectra, photoluminescence and Raman spectra. Anisotropic growth of the SnO₂ nanocrystallites was observed by altering the solvent from water to ethanol. The SnO₂ nanocrystal showed apparent quantum confinement effects. Finally, the mechanism for the formation of quantum size SnO₂ was also discussed.     

Electrical Property of Tin Oxide Doped with Multi‐Walled Carbon Nanotubes

Tin oxide doped with multi‐walled carbon nanotubes (MWNTs) was prepared via a wet‐chemical process and characterized with x‐ray diffraction (XRD) and transmission electron microscope (TEM). Meanwhile, the conductivity of composites obtained was measured using Source Meter. The results show that carbon nanotubes have great effect on the electrical property of SnO₂ nanoparticles. Compared with undoped SnO₂ nanoparticles, the resistivity of SnO₂ nanoparticles doped with 0.3‰ wt MWNTs decreased by a factor of 37. This may be ascribed to the presence of π energy levers of MWNTs and their high aspect ratio. Moreover, the effect of annealing temperature on the electrical property of SnO₂ nanoparticles doped with MWNTs also was discussed.     

SnO2双层电子传输层对钙钛矿太阳能电池界面电荷传输的影响

为了改善基于SnO₂电子传输层的钙钛矿太阳能电池的界面电荷传输特性和迟滞现象,我们采用低温溶液处理工艺制备了4种不同类型的SnO₂电子传输层用于钙钛矿太阳能电池,包括由SnCl₄·5H₂O溶胶-凝胶层(Cl₄-SnO₂)、SnCl₂·2H₂O溶胶-凝胶层(Cl₂-SnO₂)和SnO₂纳米颗粒层(NP-SnO₂)与SnO₂胶体层(Col-SnO₂)两两相互作用形成的同质结SnO₂双层电子传输层和Col-SnO₂单层电子传输层;并系统研究了不同SnO₂双层电子传输层对器件光电性能和迟滞现象的影响。通过扫描电镜(SEM)、X射线衍射(XRD)、稳态光致发光(PL)、电化学阻抗(EIS)和稳定性测试等表征证实,在Col-SnO...     

An electron microscope study of tin dioxide and antimony-doped tin dioxide

Crystals of tin dioxide, SnO₂, have been grown pure or doped with a few percent of antimony using vapor growth methods in order to investigate the microstructures of reduced and oxidized SnO₂. They were examined by X-ray diffraction and by optical and electron microscopy. SnO₂ crystals were found to contain few faults, but the antimony-doped crystals were extensively twinned in some regions. Reduction of SnO₂ crystals to yield CS phases was unsuccessful. These results are discussed in terms of the known crystal chemistry of the oxides involved.     

Application of Pt@SnO2 nanoparticles for hydrogen gas sensing

We report the fabrication of Pt@SnO₂ nanoparticles using a sol–gel method. These nanoparticles are used as a sensing material. The structural and morphological characterization of the prepared Pt@SnO₂ nanoparticles was performed using ultraviolet–visible spectroscopy, X‐ray diffraction, transmission electron microscopy, and energy‐dispersive X‐ray spectroscopy. The sensor responses of SnO₂ and 1 wt% Pt/SnO₂ to 1% hydrogen gas (H₂) were 1.3 and 1.9, respectively. The sensor response of a Pt@SnO₂ core–shell sensor increased to 5.1 at room temperature; it improved by 3.9 times compared to SnO₂ and by 2.7 times compared to 1% Pt/SnO₂ in sensing 1% H₂. The response time for the prepared Pt@SnO₂ sensor was also shortened by 2.0 and 1.4 times compared to SnO₂ and 1 wt% Pt/SnO₂, respectively. The sensor response increased rapidly from 1.4 to 5.1, with an increase in H₂ concentration from 800 to 10,000 ppm (1%). We investigated the H₂‐sensing mechanism of Pt@SnO₂.     

Synthesis,characterization, and biosensing application of ZnO/SnO2 heterostructured nanomaterials

In this work, zinc oxide/tin oxide (ZnO/SnO₂) heterostructured nanomaterials were synthesized by hydrothermal method. Transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction measurements revealed that the product was composed of ZnO nanowires and SnO₂ nanobranches. The novel ZnO/SnO₂ heterostructured nanocrystals were for the first time used as a supporting matrix to explore a novel immobilization and biosensing platform of redox proteins. UV–visible absorption investigation indicated that hemoglobin (Hb) intercalated well in the ZnO/SnO₂ heterostructured nanocrystals retained its native structure. Comparative experiments have confirmed that the ZnO/SnO₂-based biosensor not only had enhanced direct electron transfer capacity but also displayed excellent electrocatalytic properties such as higher sensitivity and wider linear range to the detection of hydrogen peroxide in comparison with the ZnO- and SnO₂-based biosensors.     

Energy band alignment of SnO2/SrTiO3 epitaxial heterojunction studied by X‐ray photoelectron spectroscopy

(200) SnO₂//(111) SrTiO₃ (STO) epitaxial heterojunctions were fabricated using the laser molecular epitaxy technique. Sharp junction interface was confirmed by the high‐resolution transmission electron microscopy. The valence band offset and conduction band offset of the SnO₂/STO heterojunction were determined to be 0.85 ± 0.20 and 0.45 ± 0.20 eV using XPS, respectively. It is found that a type‐II band alignment forms at the SnO₂/STO interface. Copyright © 2015 John Wiley & Sons, Ltd.     

不同载体对负载型氧化钨催化剂在己二酸合成反应中的结构及性能影响

以SBA-15、六角介孔二氧化硅（HMS）和SnO₂为载体,通过浸渍法合成了含钨负载型催化剂,并考察了三种催化剂在环氧环己烷选择氧化制备己二酸反应中的催化性能. 通过X射线衍射（XRD）,透射电镜/场发射透射电镜（TEM/FETEM）,紫外-可见漫反射光谱（UV-Vis DRS）,拉曼（Raman）光谱,X射线光电子能谱（XPS）以及傅里叶变换红外（FTIR）光谱等手段对各种催化剂的结构进行表征. 结果表明,载体与催化剂的性能有密切的关系. 以SnO₂为载体的WO₃/SnO₂催化剂活性最高,其次是WO₃/HMS催化剂,WO₃/SBA-15 催化剂的活性最差.XRD 分析显示WO₃/SnO₂催化剂中氧化钨物种的晶化程度最低,TEM 和XPS 结果表明氧化钨物种在WO₃/SnO₂催化剂表面高度分散并且粒径尺寸很小（约2 nm）,UV-Vis DRS结果表明在WO₃/SnO₂催化剂中存在孤立[WO₄]四面体和低聚态的钨物种,这些物种的存在可能是WO₃/SnO₂催化剂具有高活性的主要原因. 此外,WO₃/SnO₂催化剂可以重复使用多次,6 次反应后己二酸（AA）得率仍然保持在80%以上,说明氧化钨物种与SnO₂载体间存在强烈的相互作用,从而提高了催化剂的稳定性.     

Binding Characteristics of CoPc/SnO2 by In-situ Process and Photocatalytic Activity under Visible Light Irradiation

Cobalt phthalocyanine (CoPc) was synthesized and self-assembled on the surface of nanoscale tin dioxide (SnO₂) by in-situ process, marked as i, and Co-O interaction was verified to conjugate axially between macromolecule (CoPc) and SnO₂ in CoPc/SnO₂(i). The results indicated that the binding constant of CoPc/SnO₂(i) was two-order higher than that of CoPc/SnO₂(d) synthesized by dipping process, marked as d, while the numbers of binding sites were comparable in both samples. The degradation rate in the photocatalytic activity of CoPc/SnO₂(i) was 32.5% higher than that of CoPc/SnO₂(d) under visible-light irradiation for 150 min due to the effective electron separation and energy injection from LUMO of CoPc to conduction band of SnO₂ for CoPc/SnO₂(i) based on the strong interaction between CoPc and SnO₂. The degradation recyclability of CoPc/SnO₂(i) retained 48.8% in 10 times under the same circular photocatalytic process.     

Size-controlled synthesis of SnO2 nanoparticles using reverse microemulsion method

Tin oxide nanoparticles were prepared using an ionic surfactant (sodium dodecyl sulfate) and tin (IV) chloride as an inorganic precursor via the reverse microemulsion method. The size of the nanoparticles is controlled by variation of water-to-surfactant ratio. Eliminating of surfactant in prepared nanoparticles was confirmed by the infrared spectroscopy after sequential calcinations. Transmission electron microscopy, surface area, pore volume, average pore diameter, pore size distribution and X-ray diffraction results were used for evaluation of size distribution, shape and structure of prepared SnO₂ nanoparticles. Transmission electron micrographs confirmed that the obtained materials are spherical nanoparticles. The X-ray diffraction results show the crystalline phases of all samples are SnO₂ with tetragonal structured crystal. In addition, the X-ray diffraction and transmission electron microscopy data showed that the size of SnO₂ nanoparticles decreased with decreasing the water-to-surfactant ratio.     

In situ chemical synthesis of SnO2–graphene nanocomposite as anode materials for lithium-ion batteries

An in situ chemical synthesis approach has been developed to prepare SnO₂–graphene nanocomposite. Field emission scanning electron microscopy and transmission electron microscopy observation revealed the homogeneous distribution of SnO₂ nanoparticles (4–6 nm in size) on graphene matrix. The electrochemical reactivities of the SnO₂–graphene nanocomposite as anode material were measured by cyclic voltammetry and galvanostatic charge/discharge cycling. The as-synthesized SnO₂–graphene nanocomposite exhibited a reversible lithium storage capacity of 765 mAh/g in the first cycle and an enhanced cyclability, which can be ascribed to 3D architecture of the SnO₂–graphene nanocomposite.     

High-resolution transmission electron microscopy investigation of nanostructures in SnO2 thin films prepared by pulsed laser deposition

Pulsed laser deposition (PLD) was used to grow nanocrystalline SnO₂ thin films onto glass substrates. The nanocrystallites and microstructures in SnO₂ thin films grown by PLD techniques have been investigated in detail by using X-ray diffraction and high-resolution transmission electron microscopy (HRTEM). The PLD process was carried out at room temperature under a working pressure of about 2×10⁻⁶ mbar. Experimental results indicate that thin films are composed of a polycrystalline SnO₂ and an amorphous SnO phase. In particular, the presence of such an amorphous SnO phase in the thin films greatly limits their practical use as gas-sensing devices. HRTEM observations revealed that SnO₂ nanocrystallites with tetragonal rutile structure embed in an amorphous SnO matrix, which are approximatively equiaxed. These approximatively equiaxed SnO₂ nanocrystallites contain a high density of defects, such as twin boundaries and edge dislocations. The grain growth of SnO₂ thin films may be discussed in terms of the coalescent particle growth mechanism.