Gamma radiolysis of Methyl Red solution and reaction induced by γ-irradiated NaCl in Methyl Red

The -radiolysis of Methyl Red solution in HCl medium at pH=2 has been studied along with energy transfer reaction brought about byF and hole centers of -irradiated NaCl. The G-values for degradation of the azo dye indicator by radiolysis and -irradiated salt were determined as 9·10^–1 and 4.8·10^–3, respectively. The kinetic rate constants (k) of degradation are evaluated as 2·10^–5 rad^–1 in the case of direct radiolysis, while for the irradiated salt it is 2·10^–7 rad^–1. The extent of degradation by direct -radiolysis is 100–200 times greater as compared to that by the -irradiated salt. The same mechanism is proposed for radiolysis as well as the reaction induced by -irradiated sodium chloride.     

2,3-Dihydroxypyridine Loaded Amberlite XAD-2 (AXAD-2-DHP): Preparation, Sorption–Desorption Equilibria with Metal Ions, and Applications in Quantitative Metal Ion Enrichment from Water, Milk and Vitamin Samples

2,3-Dihydroxypyridine loaded (via –N=N–linker) Amberlite XAD-2 (AXAD-2-DHP) was prepared and characterized by elemental analyses, TGA and FT-IR spectra. It (1g packed in a column of 1cm diameter; surface area 135.5m²g^–1) was found to be an effective solid phase sorbent for enriching Zn²⁺, Mn²⁺, Ni²⁺, Pb²⁺, Cd²⁺, Cu²⁺, Fe³⁺ and Co²⁺ at pH 3.5 to 7.0 using flow rates between 1.0–5.0mLmin^–1. For desorption (recovery 97.0–99.8%) of the metal ions, 8 to 10mL of 2.0molL^–1 HCl or 1.5molL^–1 HNO₃ at a flow rate of between 2.0 and 4.0mLmin^–1 were found most suitable. The t_1/2 (time for 50% sorption) is between 2 and 10min when a 50mL solution (containing a total amount of metal of 2mg) was equilibrated with 0.5g of resin. Sorption of all metal ions except Pb²⁺ follows the Langmuir model, whereas for Pb the data fits with the Freundlich model. The sorption capacity is between 60.7 (for Cd) and 406.7 (for Cu) µmolg^–1. The resin can withstand an acid concentration of 6molL^–1 and can be reused for thirty cycles of sorption–desorption. The preconcentration factor varies between 100 and 300. For Cd, Ni and Cu the sorption capacity of 2,3-dihydroxypyridine loaded cellulose is lower than that of the present resin. The tolerance limits of electrolytes, humic acid, complexing agents, Ca²⁺ and Mg²⁺ in the enrichment of all metal ions are reported. The limits of detection are 3.88, 5.37, 8.72, 13.88, 4.71, 1.24, 0.59 and 0.30µgL^–1 for Zn²⁺, Mn²⁺, Ni²⁺, Pb²⁺, Cd²⁺, Cu²⁺, Fe³⁺ and Co²⁺, respectively. The calibration curves for flame AAS determination were linear in the ranges 0.018–1.0, 0.067–5.0, 0.2–5.0, 0.9–20, 0.028–2.0, 0.077–5.0, 0.19–10 and 0.1–3.5µgmL^–1, respectively. All the eight metal ions in river and synthetic water samples, Co in vitamin tablets and Zn in milk samples have been quantitatively enriched with Amberlite XAD-2-DHP and determined by flame atomic absorption spectrometry.     

Tetramethyl(2-methoxyethyl)cyclopentadienyl complexes of zirconium(iv). Crystal structure of [η5:η1−C5(CH3)4(CH2CH2OCH3)]ZrCl3

Several novel zirconium(iv) complexes with the chelating oxygen-containing cyclopentadienyl ligand, tetramethyl(2-methoxyethyl)cyclopentadiene, have been synthesized. [⁵:¹-Tetra-methyl(2-methyl)cyclopentadienyl]trichlorozirconium (2), bis[⁵-tetramethyl(2-methoxyethyl)cyclopentadienyl]dichlorozirconium (3), [⁵-pentamethylcyclopentadienyl][⁵-tetra-methyl(2-methoxyethyl)cyclopentadienyl]dichlorozirconium (4), and [⁵-tetra-methyl(2-methylthioethyl)cyclopentadienyl][⁵-tetramethyl(2-methoxyethyl)-cyclopentadienyl]dichlorozirconium (5) have been prepared from the corresponding lithium cyclopentadienide (l). The crystal structure of cyclopentadienyl complex2 has been established by X-ray analysis. The coordination OZr bond in compound2 exists both in the crystalline state and in solutions. No coordination of this type was observed in complexes3–5. Synthesized complexes2–5 are discussed in comparison with their sulfur-containing analogs.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1828–1832, July, 1996.     

Transformed steroids. 161. Reactivity of 17-spirooxetane-20-ketosteroids towards opening of the four-membered ring

Conclusions Replacement of the 20-oxo group in 17,21-epoxypregn-5-en-3-ol-20-one by the hydrazono-group affects the cleavage of the oxetane ring by thiocyanic acid, reaction occurring preferentially by introduction of^–NCS at C¹⁷ with consequent expansion of the four-membered ring to a six-membered ring with the formation of the [17; 21]-1,3-tetrahydrooxazine-2-thione.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 6, pp. 1393–1396, June, 1987.     

Complex formation equilibria in iron(III)-L-alanine system

Summary Complex formation in iron(III)-L-alanine solutions was studied by emf glass electrode and spectrophotometric measurements, in 0.5 mol dm ^–3 (Na)NO₃ medium, at 25 ° C. In the concentration range 0.5 [Fe]₀ 20.0, 5.0 [Ala]₀ 1000.0 (mmol dm^–3) and 1.0 -log [H⁺] 3.5; {[Ala]/[Fe] = 10:1-100:1| the equilibria in the title system were explained by the model including the species FeHL, FeL, Fe(OH)L, Fe₂(OH)₂L₂ (where HL denotes L-alanine) and several hydrolytic products. The stability constants of complexes are given. The mechanism of formation and structure of complexes in solution is proposed.Abbreviations Ala alaninate ion - HAla alanine (zwitterion) - AlaH alanine (neutral) - H₂Ala⁺ alanine cation     

Electrochemical Determination of Cinnamtannin B1 with a Pyrolytic Graphite Electrode

Cinnamtannin B1 (trimeric proanthocyanidin), which is identified and isolated from the effective fraction of the root of Lindera aggregata (Sims) Kosterm, is one kind of condensed tannin used as an effective antipyrotic and antitumor agent. Its electrochemical response can be obtained at a pyrolytic graphite electrode. Consequently, an easily performed and sensitive method for the determination of cinnamtannin B1 is developed. The detection limit is estimated to be 1.0×10^–7M with the linear determination range of 2.0×10^–7M to 1.8×10^–6M. Five replicate analyses of 1.0×10^–6M cinnamtannin B1 yields an RSD value of 2.1%. Since the working electrode does not need to be modified with any other species, it is very stable, repeatable and easily treated, and this method therefore potentially useful in real sample analysis.     

Electrochemical Properties and Analytical Applications of Keggin-type Phosphomolybdic Anions in Electrostatically Linked 2-Aminoethanethiol Self-Assembled Monolayers

A composite film containing a heteropolyanion was prepared on a 2-aminoethanethiol (AT) self-assembled monolayer film-modified gold electrode by attaching the Keggin-type phosphomolybdic anion. The surface structures and electrochemical properties of the composite films were characterized by using ATR-FTIR, AC impedance, cyclic voltammetry and chronocoulometry. FTIR studies indicated that there was some electrostatic interaction between Pmo₁₂O₄₂^7– and surface NH₃⁺. Three reversible redox couples were observed in 1.0molL^–1 H₂SO₄ in the potential range of 0–0.7V for the composite film modified electrode, which were attributed to two-electron and two-proton electrochemical processes of PMo₁₂O₄₂^7–. The diffusion coefficient is determined to be 2.04×10^–7cm²s^–1. The composite film shows good catalytic activities for the reduction of nitrite (NO₂^–) in acidic solution and the catalytic mechanisms are described. The modified electrode provides a linear response for NO₂^– in the concentration range of 1.0×10^–4 to 1.0×10^–7molL^–1 by differential pulse adsorptive stripping voltammetry with a correlation coefficient of 0.9965. The detection limit (three times the signal blank/slope) was 2.0×10^–8molL^–1. The modified electrode was used for the determination of NO₂^– in wastewater.     

Triterpene glycosides of Hedera taurica. IV. Structure of hederosides A1, A2, D1, and D2 from the berries of Crimean ivy

New triterpene glycosides have been isolated from the berries of Crimean ivyHedera taurica Carr. (family Araliaceae) — hederoside A₁ (methyl ester of 3-O--D-glucopyranosylhederagenin) and hederoside D₁ 3-O-[O--D-glucopyranosyl]-(12)--D-glucopyranosyl]hederagenin and also the known glycosides 3-O--D-glucopyranosyloleanolic acid and 3-O-[O--D-glucopyranosyl-(12)--L-arabinopyranosyl]hederagenin. The structures of these compounds were established on the basis of the results of chemical methods and¹H and¹³C NMR spectroscopy.M. V. Frunze Simferopol' State University. Translated from Khimiya Prirodnykh Soedinenii, No. 2, pp. 228–230, March–April, 1990.     

Comment of the influence of annealing on the distribution of chain defects in drawn polyethylene

The present study suplements preceding investigations [1–5] concerning the distribution of chain-defects between crystalline regions and crystal surface, and extends them to the influence of annealing in case of drawn branched polyethylene (PE). For this purpose available unit cell data for annealed drawn PE with=3%, at various annealing temperatures and times, are examined by assuming the penetration of chain defects at interstitial crystal sites by means of 2gl kink generation. The analysis of results shows that the initial level of 8×10^–2 chain defects expanding the lattice decreases linearly as a function of annealing temperature. After annealing at 100 °C during 3×10³ min this level decreases to values < 10^–3. It is suggested that these space-filling point defects can be converted through chain diffusion in amorphous defects, cooperative defects and/or in defects segregated into the surface layer.     

Polarographic Determination of Lovastatin in the Presence of H2O2 in Pharmaceuticals, Human Urine and Serum

The polarographic reduction and catalytic behavior of lovastatin are studied by polarography and cyclic voltammetry. The reduction wave of lovastatin appears at ca. –1.49V (vs. SCE) in 0.16molL^–1 Na₂B₄O₇–KH₂PO₄ (pH=7.4) supporting electrolyte containing 20% ethanol. It is ascribed to a 2e^–, 2H⁺ addition to the carbonyl group on lactone ring. If H₂O₂ is present, the reduction wave is catalyzed to produce a polarographic catalytic wave. Based on the catalytic wave, a novel method for the determination of lovastatin is proposed. A rectilinear calibration curve of the catalytic wave was obtained for lovastatin concentration in the range 1.5×10^–8 to 1.0×10^–6molL^–1. The peak current of the catalytic wave is ca. 12 times higher than that of the corresponding reduction wave. The detection limit is 8.0×10^–9molL^–1. The proposed method is simpler, faster and more sensitive than the known methods for lovastatin analysis, and can be applied to the direct determination of lovastatin in pharmaceuticals, urine and serum without preliminary separation.     

Anwendung der Streustrahl-Methode zur Bestimmung der Elemente in Mineral?lprodukten mit Hilfe der R?ntgenfluorescenz-Spektral-Analyse am Beispiel der Bleibestimmung in Ottokraftstoffen

Zusammenfassung In einem relativ einfach durchzuführenden Verbundverfahren wird Selen im Sauerstoff-strom innerhalb 15 min bei 1100–1150°C quantitativ aus den Metall- bzw. Metalloxidschmelzen verdampft und in einer mit flüssigem Stickstoff gekühlten Vorlage aufgefangen. Das aus der Vorlage mit einer definierten Menge verdünnter HNO₃ in Gegenwart von Ni-Nitrat gelöste Selen läßt sich direkt durch AAS mit dem Graphitofen (FAAS) äußerst nachweisstark und zuverlässig bestimmen. Die Nachweisgrenze (elektrodenlose Entladungslampe) liegt bei 3×10^–11 g Se. Der Verfahrensverbund erlaubt mit Probenmengen 10 g in Ag und Au Se-Gehalte 0,05 ppb,inCu 0,1 ppb,in Bi 0,2 ppb und in Pb 10 ppb zu erfassen. Für draht-, stab- und spanförmige Proben erhält man für Se-Gehalte von 2–0,002 ppm Variationskoeffizienten zwischen 3 und 6%. Die Vollständigkeit der Se-Verdampfung aus den Matrices Cu, Ag, Au und Bi wurde ebenso wie die Richtigkeit des Gesamtverfahrens durch systematische Untersuchungen belegt.

---

Determination of se by furnace atomic absorption spectrometry (FAAS) in the ppb-range in Cu, Cu alloys, Ag, Au, Pb and Bi after volatilization in an oxygen stream

Summary Selenium is evaporated in a multi-stage procedure within 15 min from metals or metal oxides fused at temperatures of 1100–1150°C under a stream of oxygen and is trapped in a receiver cooled with liquid nitrogen. The condensed SeO₂ is dissolved with a definite volume of diluted HNO₃ in the presence of Ni-nitrate and determined with high sensitivity and reliability by FAAS (electrodeless discharge lamp). The detection limit of the FAAS was found to be 3 · 10^–11 g of Se. The multi-stage procedure allows to detect Se levels 0.05 ppb in Ag and Au, 0.1 ppb in Cu, 0.2 ppb in Bi, and 10 ppb in Pb, respectively, with sample weights 10 g. For wire, rod, and chip samples the coefficients of variation are found to be between 3 and 6% for Se contents of 2 to 0.002 ppm. The quantitative evaporation of Se from Cu, Ag, Au, and Bi as well as the accuracy of the whole procedure have been checked systematically.

Die Arbeit wurde durch Mittel der DFG in dankenswerter Weise unterstützt.     

Electrosurface and Ion-Selective Properties of Track-Etched Nanofilters: The Effect of Polyvalent Metal Adsorption

The effect of polyvalent metal adsorption on the performance and ion selectivity of poly(ethylene terephthalate) track-etched membranes with pores of 10 nm in diameter was studied. Membrane samples were prepared from the track-etched membranes with pores of 20 nm in diameter by thermal shrinkage. It was shown that an effective pore diameter decreases and selectivity of track-etched membranes increases upon filtration of Al(NO₃)₃ and Cr(NO₃)₃ solutions. The results obtained are explained by ion adsorption leading to the formation of complexes between polyvalent metals and carboxyl groups on the pore surface that is confirmed by IR spectroscopy data. The study of electrosurface properties of modified membranes and the dependence of ion selectivity of track-etched membranes on the concentration of Al³⁺ ions in 10^–2 M KCl solution indicates the decrease of membrane negative surface charge resulted from Al³⁺ adsorption and membrane charge reversal at Al³⁺ concentration in a solution higher than 10^–6 M. The dependences of the ion selectivity on pH and Al³⁺ concentration C _Al in a solution are similar. At pH < 3 and C _Al > 10^–6 M, the _1–2 > _1–1 > _2–1 ion selectivity series characteristic of the initial negatively charged membranes for the 1–1, 1–2, and 2–1 electrolyte solutions is reversed into the _2–1 > _1–1 > _1–2 series characteristic of positively charged membranes.     

Kinetics of the thermal and photochemical decomposition of aquapentacyanoferrate(III) in aqueous solution

Summary The kinetics of the thermal and photochemical decomposition of aquapentacyanoferrate(III) ion in aqueous solution in the presence ofo-phenanthroline was studied spectrophotometrically. The first-order rate constant (k ) at 30° C [I=1 M(NaCl)] for the thermal reaction is (1.49±0.13)×10^–6 s^–1 with H =(158±7)kJ mol^–1 and S=(42±4) JK^–1 mol^–1. The initial quantum yield for the photochemical reaction at pH=7 is independent of the light intensity and is (1.49±0.33)×10^–2 mol einstein^–1.A communication on this subject was presented at the XVI Latinamerican Chemistry Congress held at Rio de Janeiro. Brasil, October 14–20, 1984.     

Voltammetric Behavior of Dopamine at ct-DNA Modified Carbon Fiber Microelectrode

A sub-micrometer thin-layer DNA modified carbon fiber microcylinder electrode was prepared by electrodeposition of ct-DNA at 1.5V (vs. Ag/AgCl). The voltammetric behavior of dopamine (3-hydroxytyramine) was investigated at the modified electrode. It was found that the modified electrode exhibits a highly electrocatalytic activity toward dopamine oxidation. Differential pulse voltammetry was used for determination of dopamine in pH 7.4 phosphate buffer solution. A linear response of the peak current versus the concentration was found in the range of 4×10^–6 to 10^–4molL^–1 at 10^–4molL^–1 AA (ascorbic acid) coexistence (R=0.9959) and the range of 6×10^–5 to 10^–3molL^–1 at 10^–3molL^–1 AA (R=0.9960). The presence of a high concentration of ascorbic acid did not interfere with the determination. The proposed method exhibited good recovery and reproducibility. This method can be applied to the detection of DA in real samples.     

Accumulation of host—guest ion complexes with different counterions at the water—supercritical CO2 interface: a molecular dynamics study

The behavior of ion complexes at the water—supercritical carbon dioxide interface was considered by molecular dynamics simulations. The following complexes were studied: Cs⁺calix[4]crown-6, K⁺222 cryptate with chloride or dicarbollide (CCD^–) counterions, the Sr²⁺18C6 complex with the picrate (Pic^–) or perfluorooctanoate (PFO^–) counterions, and the Cl^–Tet ⁴⁺ complex with chloride counterions (Tet ⁴⁺ is a tetrahedral tetraammonium cation). The simulations demonstrate the analogy between aqueous interfaces with organic immiscible liquids and the CO₂ phase. Water and supercritical CO₂ are poorly miscible and form an interface. Most of the complexes are accumulated at the interface, instead of diffusing into the organic phase in which they should be more soluble. In addition, marked counterion effects are observed. The CCD^–, Pic^–, and PFO^– anions are surface active and are concentrated at the interface, but show different relationships with the complexes. The formation of ion pairs is precluded by the very hydrophobic CCD^– anions, which promote the extraction of cryptates as separated ion pairs to the CO₂ phase. Conversely, the extraction of the Sr²⁺ ions with 18C6 proceeds via a co-complexation mechanism, including the formation of the Sr18C6(PFO)₂, complex having a CO₂ affinity. The mechanism of assisted ion transfer to the CO₂ phase is discussed.     

Kinetic and mechanistic studies on the interaction of thymidine with the hydroxopentaaquarhodium(III) ion

The interaction of thymidine, a nucleoside, with hydroxopentaaquarhodium(III), [Rh(H₂O)₅(OH)]²⁺ ion in aqueous medium is reported and the possible mode of binding is discussed. The kinetics of interaction between thymidine and [Rh(H₂O)₅OH]²⁺ has been studied spectrophotometrically as a function of [Rh(H₂O)₅OH²⁺], [thymidine], pH and temperature. The reaction has been monitored at 298 nm, the _max of the substituted complex, and where the spectral difference between the reactant and product is a maximum. The reaction rate increases with [thymidine] and reaches a limiting value at a higher ligand concentration. From the experimental findings an associative interchange mechanism for the substitution process is suggested. The activation parameters (H=47.8 ± 5.7 kJ mol^–1, S=–173 ± 17 J K^–1 mol^–1) supports our proposition. The negative G⁰ (–13.8 kJ mol^–1) for the first equilibrium step also supports the spontaneous formation of the outer sphere association complex.     

Energy Transfer Electrogenerated Chemiluminescence for the Determination of Sulfite

A simple and novel electrogenerated chemiluminescence (ECL) method for the determination of sulfite has been developed based on the energy transfer ECL process. It was found that a weak ECL signal of sulfite was electrochemically generated on a platinum electrode in neutral aqueous solution. The signal was strongly enhanced by rhodamine B as an energy receptor and further enhanced by the neutral surfactant Tween 80. In 0.10M phosphate buffer solution (pH=7.5) containing 2.0×10^–6gmL^–1 rhodamine B and 0.4% (v/v) Tween 80, the ECL response to the concentration of sulfite at a potential of 0.82V was linear over a range of 1.0×10^–7gmL^–1 to 8.0×10^–6gmL^–1, and the detection limit was 5×10^–8gmL^–1. The relative standard deviation (n=11, 1.0×10^–6gmL^–1) was 3.8%. The proposed method has been successfully applied to the determination of sulfite in pharmaceutical injections and white sugar samples.     

Effect of Sodium Thiosulfate on the Kinetics of Electron–Ion Processes in Powdered Silver Chloride

The results of a microwave photoconductivity study on the effect of pretreatment of a silver chloride powder with sodium thiosulfate (STS) aqueous solutions on the kinetics of electron–ion processes in silver chloride are reported. At an UV light fluence of <10¹⁴ photon/cm^–2 per pulse, photoresponse decay after the end of the pulse consisted of two exponential components over the entire concentration range 10^–8–10^–2 mol STS/mol AgCl examined. The amplitude of the components and the ratio between the slow ^s and fast ^f components depended on the sodium thiosulfate concentration, which was due to the formation of an additional number of new electron traps in AgCl. An analysis of the kinetics in terms of models taking into account various types of decay of an excess electron made it possible to obtain data on the depth of both old traps (0.45 eV) and new STS-created traps (0.45–0.63 eV) in AgCl.     

Die Ringinversions-Barriere in [2.2]Metacyclophan

From racemization studies on optically active [2.2]metacyclophanes substituted in position 4, the parameters of activation for the inversion of the tenmembered ring were found to be: G ₄₂₃ =31.5 kcal/mole, H =27.5 kcal/mole and S =–10 Cl/mole.Racemization does not occurvia bond forming or breaking; the value for the inversion barrier is not affected by substituents in position 4 and therefore corresponds to the value of unsubstituted [2.2]metacyclophane, whereas substituents in the bridge exert a distinct influence. These results can easily be explained on the basis of the isoconformational concept.

---

---

Mit 5 Abbildungen

---

Herrn Prof. Dr.O. Hoffmann-Ostenhof mit besten Wünschen zum 60. Geburtstag gewidmet.     

Effect of aminoacids on the surface free energy of nitrofurantoin

Changes in nitrofurantoin surface free energy components, Lifshitz-van der Waals, _s ^LW , electron donor, _s ^– , and electron acceptor, _s ⁺ , due to adsorption of the aminoacids: lysine, alanine and glutamic acid, were determined by means of the thin-layer wicking technique. It was found that the aminoacids slightly increase the _s ^– component already at 10^–4 M concentration. They reduce the _s ⁺ component practically to zero, and a very sharp increase of _s ^– was observed when the nitrofurantoin surface was precovered from the solutions at concentrations larger tan 10^–4 M. It is concluded that the adsorption of the aminoacids takes place via hydrogen bonding and electrostatic interactions between nitrofurantoin surface and aminoacid molecules. The increase in the _s ^– parameter is probably caused by the presence of carboxyl groups in the aminoacid molecules.