Poly(2‐hydroxyethyl methacrylate‐co‐N,O‐dimethacryloylhydroxylamine) particles by dispersion polymerization

Poly(2‐hydroxyethyl methacrylate‐co‐N,O‐dimethacryloylhydroxylamine) particles were prepared by dispersion polymerization in toluene/2‐methylpropan‐1‐ol medium using cellulose acetate butyrate and dibenzoyl peroxide (BPO) as a steric stabilizer and initiator, respectively. The particle size was reduced with decreasing solvency of the reaction medium (more nuclei were generated) because the critical chain length of the precipitated oligomers decreased with an increasing toluene content, which is a poorer solvent for the polymer than 2‐methylpropan‐1‐ol. There is an optimum initiator concentration (2 wt % BPO relative to monomers) for producing low‐polydispersity particles under given conditions. Additionally, discrete spherical particles were obtained at a low monomer concentration and/or higher polymerization temperature. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1625–1632, 2002     

水分散体系中由BPO或KPS引发的苯乙烯反向原子转移自由基聚合

分别以过氧化二苯甲酰 (BPO)和过硫酸钾 (KPS)为引发剂、1 ,1 0 邻二氮菲为催化剂配体、十二烷基磺酸钠为乳化剂 ,在水分散体系中进行了苯乙烯的反向原子转移自由基聚合反应 .结果表明 ,对于BPO引发的苯乙烯乳液聚合反应 ,必须由CuBr和CuBr2 形成复合催化剂体系才能达到较好的控制效果 ,其中CuBr可以是直接加入到催化剂体系中 ,也可以是由CuBr2 与Cu0 就地快速反应生成 .CuBr迅速地与BPO反应而实现活性聚合中所谓的“快引发” ,从而有效地控制苯乙烯的聚合反应 .对于KPS引发的苯乙烯乳液聚合体系 ,反应介质的pH值对聚合有很大的影响 ,反应速度随着反应介质pH值的升高而加快 .实验结果表明 ,由两种不同引发剂引发的苯乙烯的乳液的粒径及粒径分布也有很大的差异     

Synthesis and characterization of nano-sized poly[(butyl acrylate)-co-(methyl methacrylate)-co-(methacrylic acid)] latex via differential microemulsion polymerization

Poly[(butyl acrylate)-co-(methyl methacrylate)-co-(methacrylic acid)] latex particles were synthesized via differential microemulsion polymerization. The effect of initiator type and methacrylic acid incorporation were investigated. The initiator type could significantly affect the particle size and the molecular weight of the resulting polymer and 2,2′-azobisisobutyronitrile produced the smallest particle size. The incorporation of methyl methacrylate (MAA) in the copolymer and terpolymer structures was confirmed by FTIR and NMR spectroscopy, and DSC in that the carbonyl peak of carboxylic acid at 1,700 cm^?1 in the FTIR spectrum was observed when the MAA amount was high enough, the peak areas at 0.9 ppm in the NMR spectrum confirmed the participation of MAA from the increasing proton signals and the glass transition temperature and polarity of the polymer increased when the MAA amount was increased. This supported that the MAA was incorporated into the polymer chains. MAA was found to produce a vitrification effect during the polymerization.     

Emulsion terpolymerization of butyl acrylate/methyl methacrylate/vinyl acetate: Experimental results

A systematic study of the terpolymerization of butyl acrylate/methyl methacrylate/vinyl acetate (BA/MMA/VAc) was conducted. In this stage of the study, batch emulsion terpolymerizations were performed in a 5 L stainless steel pilot plant reactor. The experiments were designed using a Bayesian (optimal) technique. The polymers produced were characterized for conversion, composition, molecular weight, and particle size. Conversion, terpolymer composition, number- and weight-average molecular weight, and average particle size results are discussed in light of the influence of seven factors and the interaction of these factors. The factors studied include monomer feed composition, initiator concentration, chain transfer agent concentration, impurity concentration, initiator type, emulsifier concentration, and temperature. A “two-stage rate” phenomenon, similar to that occurring in bulk co- and terpolymerization and emulsion copolymerization of acrylic/vinyl acetate systems was observed in the conversion, composition and molecular weight data. Furthermore, an interesting yet often ignored effect of impurities on emulsion polymerization kinetics was explained. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1659–1672, 1997     

Synthesis and properties of semi-interpenetrating network based on styrene-acrylonitrile-vinyl acetate terpolymer and zinc acrylate

Semi-Interpenetrating polymer network materials (semi IPNs) have been synthesized from styrene-acrylonitrile-vinyl acetate terpolymer as polymer I and zinc acrylate as polymer II, using divinyl benzene as crosslinking agent for polymer II. The terpolymer was pre-synthesized by a radical polymerization method using AIBN as the radical initiator. The terpolymer has been characterized by IR and elemental analysis. The composition (Sty: AN:VAc) = (0.25:0.50:0.25), the intrinsic viscosity (0.16 dl/g), the softening temperature range (180–185 °C), the glass transition temperature (23 °C) and the thermal stability (up to 300 °C) of the terpolymer were determined. The IPN was characterized by determining its density (1.12 g/cc at 30 °C), molecular weight between crosslinks (M_c = 1469), thermal stability (~ 400 °C), glass transition temperature (41 °C, 78 °C) and two-phase morphology.     

甲基丙烯酸缩水甘油酯/苯乙烯固相接枝聚丙烯

以苯乙烯(St)为共单体，过氧化苯甲酰(BPO)为引发剂，采用固相接枝反应将甲基丙烯酸缩水甘油酯(GMA)接枝到聚丙烯(PP)大分子链上。研究了反应时间、单体用量、引发剂用量等因素对接枝率的影响。采用凝胶渗透色谱(GPE)测定了PP和接枝物PP-g-(GMA-St)的分子量和分子量分布。结果 表明固相接枝PP反应条件为[GMA／[St]=2，反应3．5h，加入GMA 10份，BPO 5份。St的加入有助于GMA与PP的接枝，同时在一定程度上抑制了PP的降解。     

乙醇-水介质中单分散聚甲基丙烯酸甲酯微球的制备

与一般的以非极性脂肪烃或甲醇 水作为分散介质不同 ,采用乙醇 水混合溶剂作为分散介质进行了聚甲基丙烯酸甲酯的分散聚合 ,讨论了醇 水比例对聚合的影响 .在反应中 ,采用了一种新的加热反应方式 ,先高温反应一段时间以利于成核 ,然后降温到一较低温度反应至结束 .这种反应方式取得了明显的效果 ,大大降低了粒度分布 .此外 ,还研究了引发剂种类对粒径大小及分布的影响 ,发现混合引发剂偶氮二异丁腈 (AIBN)和过硫酸钾 (KPS)中即使只含有少量的KPS ,也会明显使粒径减小 ,分布变宽     

Microemulsion Polymerization of Methyl Methacrylat

The microemulsion polymerization of methyl methacrylate was studied. The effects of feeding modes on the structure and the properties of the obtained polymer microlatex were investigated by measuring the conversion, the transmittance and the refractive index of the latex, and by measuring the particle size, the molecular weight and the glass transition temperature (Tg) of the polymers. The results show that compared to the batch feeding mode, the semi-continuous feeding mode is more favorable to form a PMMA microlatex with a higher transmittance, a smaller particle size, a higher molecular weight and a higher Tg. And the obtained PMMA microlatex has a 30 %-40 % (mass fraction) polymer content, a 0.03 emulsifier/water weight ratio, a 0.05emulsifier/monomer weight ratio and a 17 nm average particle diameter, which is very important for the industrialization of the microemulsion polymerization technique.     

Synthesis of highly crosslinked monodisperse polymer particles: Effect of reaction parameters on the size and size distribution

Monodisperse polystyrene particles crosslinked with different concentrations of divinylbenzene were synthesized in the 3.2–9.1 μm size range by dispersion polymerization in an isopropyl alcohol/toluene mixed‐dispersion medium with poly(N‐vinylpyrrolidone) as a steric stabilizer and 2,2′‐azobisisobutyronitrile as a radical initiator. The effects of the reaction parameters such as the crosslinking agent concentration, media solvency (controlled by varying the amount of toluene addition), the initiator concentration, and the stabilizer concentration on the particle size and size distribution were investigated with reference particles with a monodisperse size distribution and crosslinked by 1.5 wt % divinylbenzene. The appropriate increase in media solvency was a prerequisite for preparing crosslinked particles without coagulated and/or odd‐shaped particles. The investigation of the effects of the polymerization parameters also shows that only specific sets of conditions produce particles with a monodisperse size distribution. The glass‐transition temperatures of the particles increased with increasing divinylbenzene concentration. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4368–4377, 2002     

Effect of reaction parameters on the particle size in the dispersion polymerization of 2-hydroxyethyl methacrylate

Poly(2-hydroxyethyl methacrylate) particles in the micron size range were obtained by the dispersion polymerization. Cellulose acetate butyrate and dibenzoyl peroxide were used as steric stabilizer and initiator, respectively. The ultimate particle size could be adjusted by the selection of a suitable polymerization medium consisting of an alcohol added to toluene and by varying their relative amounts. The particle size increased with increasing solubility parameter of the mixture, i.e., by decreasing the toluene/2-methylpropan-1-ol, toluene/butan-2-ol, and toluene/3-methylbutan-1-ol ratio. The particle size decreased with increasing concentration of the stabilizer and/or initiator. At the same time, the particle size distribution became narrower. Particles prepared from polymerization mixtures purged with nitrogen before the start of polymerization were smaller, and of narrower distribution, than those prepared from nitrogen-non-purged mixtures. Equilibrium swelling of particles in toluene decreased with the decreasing content of toluene in the polymerization mixture. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3785–3792, 1999     

Preparation and characterization of poly (N-isopropylacrylamide-co-dimethylaminoethyl methacrylate) microgel latexes

Monodisperse cationic thermosensitive latex microgels have been prepared by radical-initiated precipitation polymerization of N-isopropylacrylamide, methylene bisacrylamide using 2,2′-azobis(2-amidinopropane hydrochloride) as an initiator and dimethylaminoethyl methacrylate (DMAEMA) as a cationic monomer. The final microgel latexes were characterized with respect to water-soluble polymer formation, particle size and size distribution. Adding cationic monomer (DMAEMA) was found to drastically affect the particle size, but not the size distribution as observed both by transmission electron microscopy and quasielastic light scattering (QELS). However, too high a DMAEMA concentration in the feed composition led to enhanced formation of water-soluble polymer. The volume phase-transition temperature of cleaned microgels examined by QELS (particle size versus temperature) was found to be around 32 °C and was slightly dependent on the concentration of the cationic monomer. The volume phase-transition temperature range becomes broader with increasing cationic monomer concentration. In addition, the pH of the polymerization medium was found to affect the final particle size and amount of water-soluble polymer formed. Received: 29 March 2001 Accepted: 2 July 2001     

Study on soap‐free P(MMA‐EA‐AA or MAA) latex particles with narrow size distribution

Soap‐free poly(methyl methacrylate‐ethyl acrylate‐acrylic acid or methacrylic acid) [P(MMA‐EA‐AA or MAA)] particles with narrow size distribution were synthesized by seeded emulsion polymerization of methyl methacrylate (MMA), ethyl acrylate (EA) and acrylic acid (AA) or methacrylic acid (MAA), and the influences of the mass ratio of core/shell monomers used in the two stages of polymerization ([C/S]_w) and initiator amount on polymerization, particle size and its distribution were investigated by using different monomer addition modes. Results showed that when the batch swelling method was used, the monomer conversion was more than 96.0% and particle size distribution was narrow, and the particle size increased first and then remained almost unchanged at around 600 nm with the [C/S]_w decreased. When the drop‐wise addition method was used, the monomer conversion decreased slightly with [C/S]_w decreased, and large particles more than 750 nm in diameter can be obtained; with the initiator amount increased, the particle size decreased and the monomer conversion had a trend to increase; the particle size distribution was broader and the number of new particles was more in the AA system than in the MAA system; but the AA system was more stable than the MAA system at both low and high initiator amount. Copyright © 2006 John Wiley & Sons, Ltd.     

Redox Polymerization of Methyl Methacrylate in the Fluorous Triphasic System

Fluorous-phase chemistry is currently a topic of considerable interest1-6. Since fluoroustriphasic reactions were first described by the Curran and co-workers7, this triphasicsystem has been widely used for detagging7,8 and phase-vanishing reactions9-11. …     

Statistical design strategies to optimize properties in miniemulsion polymerization of methyl methacrylate

PMMA particles were synthesized by a miniemulsion polymerization method using hexadecane as costabilizer and sodium dodecyl sulfate as surfactant. Full factorial experimental design incorporating the linear regression analysis of the experimental values was used to illustrate the usefulness of this technique in miniemulsion polymerization studies. The effect of initiator concentration, costabilizer concentration, surfactant concentration, sonication time and amplitude, and their interactions on the particle size were identified. Costabilizer and surfactant concentrations influence both particle size individually whereas initiator concentration influences particle size via its interactions with the costabilizer and the surfactant. Sonication parameters influence also greatly the particle size. Two mathematical models were established, and have demonstrated the capability of predicting particle diameter from the synthesis conditions with a precision of 1-2 nm over a range from 75 to 180 nm.     

Studies on grafting of tris(2‐methoxyethoxy)vinylsilane onto ethylene‐propylene‐diene terpolymer

New graft copolymer was prepared by incorporating tris(2‐methoxyethoxy)vinylsilane (TMEVS) on ethylene‐propylene‐diene terpolymer (EPDM) by using dicumyl peroxide (DCP) as initiator, in Haake Rheocord 90 torque rheometer. The effect of EPDM concentration, TMEVS concentration, reaction time, reaction temperature and initiator concentration on the graft co polymerization was studied. The grafting efficiency of TMEVS on EPDM was confirmed by Fourier Transform infrared (FT‐IR) spectroscopy. The grafting efficiency increased with increase in the silane concentration upto 6% by weight. The grafting efficiency decreased beyond 6% by weight due to homopolymerization of TMEVS and non‐availability of carbon–carbon double bond in the EPDM terpolymer. The thermal properties of peroxide cured EPDM and hot water cured EPDM‐g‐TMEVS were studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis. The results show thermal properties like degradation tempertature and glass transition temperature of the EPDM‐g‐TMEVS were increased due to introduction of TMEVS on to EPDM terpolymer as well as the formation of thermally stable three‐dimensional network. Copyright © 2004 John Wiley & Sons, Ltd.     

Dispersion copolymerization of styrene and glycidyl methacrylate in polar solvents

Monodispersed copolymer microspheres consisting of styrene and glycidyl methacrylate have been prepared by dispersion polymerization. The effects of various polymerization parameters on the particle size and size distribution were systematically investigated. The initial solubility parameter of the system had a significant effect on the final particle size and size distribution. With decreasing initial solubility parameter, the particle size increased and the size distribution broadened. The particle size decreased with increasing stabilizer concentration, the amount of styrene in the monomer mixture, and decreasing initiator concentration. Received: 30 September 1998 Accepted in revised form: 10 December 1998     

Generalizing the polymerization conditions for the production of monodisperse polymeric particles via dispersion polymerization

In this study, the preparation of various methacrylic particles with monodisperse size via dispersion polymerization in polar media was discussed. The effect of various polymerization conditions such as polarity of the medium, monomer, stabilizer, and initiator concentration, polymerization temperature, and initiator type on the size and size distribution of these particles was evaluated. The experimental results showed that, with a decrease in the difference between medium solubility parameter (MSP) and polymer solubility parameter (PSP), stabilizer concentration and with an increase in monomer content size of the particles increased and size distribution of them became broader. The obtained results showed that the particle size and size distribution of various polymers were different functions of initiator concentration. It means that, for the production of monodisperse particles, specific amount of initiator is needed for each type of the polymers. Moreover, it was observed that the size and size distribution of the particles with higher polarity were more sensitive to changing the polarity of the medium, and the size distribution of the particles with lower glass transition temperature (T _g) is more sensitive to changing the stabilizer concentration which is because of less stability of them. Furthermore, to our surprise, the obtained results showed that, in MSP-PSP of 18.5 MPa^0.5, size and size distribution of all types of the particles became equivalent.     

Fundamental studies of grafting reactions in free radical copolymerization. III. Grafting of styrene,acrylate, and methacrylate monomers onto cis-polybutadiene using benzoyl peroxide initiator in solution polymerization

Benzoyl peroxide (BPO), due to its higher radical reactivity as compared to AIBN, is known to promote grafting onto cis-polybutadiene. Switching from AIBN to BPO initiator made a dramatic difference in the extent of grafting for styrene and methacrylate monomers, but only a modest difference for acrylate monomer. For styrene and methacrylate monomers, graft site formation is due to BPO initiator radical attack onto the backbone via allylic hydrogen abstraction. Significant levels of grafting are achieved and depend upon the relative concentrations of monomer and backbone polymer but not upon the level of initiator. For acrylic monomer, graft site formation was found to be due to polymer radical attack at the double bond in the backbone. Abstraction of allylic hydrogen also occurs but results in retardation of the overall reaction rate. Graft level was dependent upon initiator and back-bone polymer concentrations but not upon monomer concentration. The effective role of the initiator is only to produce polymer radicals; the BPO has no direct role in the formation of effective graft sites. © 1995 John Wiley & Sons, Inc.     

Grafting of methyl methacrylate onto natural rubber in supercritical carbon dioxide

The grafting of the methyl methacrylate (MMA) monomer onto natural rubber (NR) was carried out by supercritical carbon dioxide (scCO₂) swelling polymerization with benzoyl peroxide (BPO) as an initiator. Fourier transform–infrared spectroscopy (FT–IR) was used to confirm the formation of graft copolymers with the characteristic bands of symmetric C?O and C? O? C stretching vibrations at 1728 cm^?1 and 1147 cm^?1, respectively. The effects of the rubber‐to‐monomer ratio, amount of initiator, reaction time, and pressure on the monomer grafting level (GL) and grafting efficiency (GE) were investigated, and the optimum conditions for the preparation of NR‐g‐MMA were found to be 70:30 of the rubber‐to‐monomer ratio, 1.2% of the initiator content, and the reaction pressure of 23 MPa for 6 h. The thermal behavior of the NR and the different NR/MMA molar ratio grafted copolymer samples was studied by differential scanning calorimetry (DSC). The observed glass transition temperature (T_g) was consistent with the GL. The tensile strength, modulus of elasticity, elongation at break, hardness, and oil resistance of graft copolymers were determined and compared with the values of NR and that of polymerization products prepared in traditional toluene solution. The results showed that the tensile strength, modulus of elasticity, hardness and oil resistance were greatly improved after modification in scCO₂. Copyright © 2007 John Wiley & Sons, Ltd.     

甲基丙烯酸甲酯、苯乙烯与顺丁烯二酸二丁基锡三元共聚物的合成与表征

以过氧化苯甲酰(BPO)为引发剂,将顺丁烯二酸二丁基锡(DBTM)与苯乙烯(St)、甲基丙烯酸甲酯(MMA)进行本体三元共聚反应,探讨了共聚反应条件.用液相色谱、红外光谱、核磁共振氢谱和热重分析对共聚物的结构和性能进行了表征.动态热流变性实验结果表明,在含锡量相同的情况下,共聚物对PVC的热稳定效果优于DBTM,可以作为多功能化的PVC热稳定剂.