氮离子轰击能量对ta-C:N薄膜结构的影响

利用磁过滤真空阴极电弧技术制备了sp³键含量不小于80%的四面体非晶碳薄膜(ta-C), 然后通过氮离子束改性技术制备了氮掺杂的四面体非晶碳(ta-C:N)薄膜. 利用Raman光谱和X射线光电子能谱对薄膜结构的分析,研究了氮离子轰击能量对ta-C:N薄膜结构的影响. 氮离子对ta-C薄膜的轰击,形成了氮掺杂的ta-C:N薄膜. 氮离子轰击诱导了薄膜中sp³键向sp²键转化, 以及CN键的形成.在ta-C:N薄膜中,氮掺杂的深度和浓度随着氮离子能量的增大而增大. ta-C:N薄膜中sp²键的含量和sp²键团簇的尺寸随着氮离子轰击能量的增大而增加; 在ta-C:N薄膜中, CN键主要由C-N键和C＝N键构成, C-N 键的含量随着氮离子轰击能量的增大而减小,但是C＝N 键含量随着氮离子轰击能量的增大而增大.在ta-C:N薄膜中不含有C≡N键结构.     

α-C∶H膜化学结构对光学性能的影响

 选用体积分数为99.999 9%的H₂及反式-2-丁烯（T2B）为工作气体,利用低压等离子体增强化学气相沉积法制备了α-C∶H薄膜。利用傅里叶变换红外光谱仪和X射线光电子能谱对薄膜化学键和电子结构进行分析,并结合高斯分峰拟合分析了薄膜中sp³/sp²杂化键比值和sp³C杂化键分数。结果表明：薄膜中氢含量较高,主要以sp³C—H形式存在;工作气压越高,制备的薄膜中C=C键含量越少,薄膜中sp³/sp²杂化键比值和sp³C杂化键分数增加,薄膜稳定性提高。应用UV-VIS光谱仪,获得了波长在400~1 000 nm范围内薄膜的光吸收特性,结果显示: α-C∶H薄膜透过率可达98%。光学常数公式计算得到工作压强为4~14 Pa时光学带隙在2.66~2.76之间,并均随着工作气压的升高而增大。结果表明,随工作气压的升高,薄膜内sp³键减小,从而促使透过率、光学带隙增大。     

α-C∶H膜化学结构对光学性能的影响

 选用体积分数为99.999 9%的H₂及反式-2-丁烯（T2B）为工作气体,利用低压等离子体增强化学气相沉积法制备了α-C∶H薄膜。利用傅里叶变换红外光谱仪和X射线光电子能谱对薄膜化学键和电子结构进行分析,并结合高斯分峰拟合分析了薄膜中sp³/sp²杂化键比值和sp³C杂化键分数。结果表明：薄膜中氢含量较高,主要以sp³C—H形式存在;工作气压越高,制备的薄膜中C=C键含量越少,薄膜中sp³/sp²杂化键比值和sp³C杂化键分数增加,薄膜稳定性提高。应用UV-VIS光谱仪,获得了波长在400~1 000 nm范围内薄膜的光吸收特性,结果显示: α-C∶H薄膜透过率可达98%。光学常数公式计算得到工作压强为4~14 Pa时光学带隙在2.66~2.76之间,并均随着工作气压的升高而增大。结果表明,随工作气压的升高,薄膜内sp³键减小,从而促使透过率、光学带隙增大。     

OX2(X=F，Cl，Br，I，At)中的离域π63键

本文在理论层面上研究了OX₂(X=F,Cl,Br,I,At)分子的电子结构,结果表明其中存在离域π⁶₃键,氧原子采取sp²杂化方式,与价层电子对互斥理论预测的结果不符. 提出了离域稳定化能衡量形成离域π⁶₃键对能量降低的贡献,证实离域π⁶₃键对分子结构起到了额外的稳定作用. 这些现象可以总结为一种配位效应.     

掺溴非晶碳梯度薄膜的制备与分析

 采用低压等离子增强化学气相沉积法用溴乙烷、氢气制备了掺溴的非晶碳梯度薄膜。通过样品的XPS能谱分析研究了薄膜沉积速率与氢气流量、溴元素原子分数与溴乙烷流量以及溴元素原子分数与刻蚀时间之间的关系，得出了溴乙烷流量、刻蚀时间对薄膜的主要键态含量、C元素sp²/sp³键态杂化比和薄膜硬度的影响。结果表明：薄膜沉积速率随氢气流量的增加而线性减小，溴元素含量随溴乙烷流量的增加先增加后降低，刻蚀时间越长，溴乙烷流量越小，薄膜越硬     

氩离子轰击对四面体非晶碳膜内应力和摩擦系数影响的研究

利用磁过滤真空阴极电弧技术制备了sp³键大于80%的四面体非晶碳(ta-C)薄膜, 通过冷阴极离子源产生keV能量的氩离子轰击ta-C薄膜,研究了氩离子轰击能量对ta-C薄膜结构, 内应力以及耐磨性的影响.通过X射线光电子能谱和原子力显微镜研究了氩离子轰击对薄膜结构 与表面形貌的改性,研究表明,氩离子轰击诱导了ta-C薄膜中sp³键向sp²键的转化, 并且随着氩离子轰击能量的增大,薄膜中sp²键的含量逐渐增多, 薄膜内应力随着氩离子轰击能量的增大逐渐减小.氩离子轰击对薄膜的表面形貌有较大影响, 在薄膜表面形成刻蚀坑,并且改变了薄膜的表面粗糙度,随着氩离子轰击能量的增大, 薄膜的表面粗糙度也会逐渐增大.通过摩擦磨损仪的测试结果,氩离子轰击对薄膜的初始摩擦系数影响较大, 但是对薄膜的稳定摩擦系数影响较小,经过氩离子轰击前后的ta-C薄膜的摩擦系数为0.1左右, 并且具有优异的耐磨性.     

C-I键均裂解离焓的密度泛函理论研究

在高级别理论(包含使用外推基组的MP2和CCSD(T))方法及大量密度泛函方法的理论基础上, 研究了不同种类有机碘化物的C-I键均裂解离能. 密度泛函方法的系统性评估计算结果表明,MPWLYP1M方法的计算精度最高. 运用该方法系统地考查了C(sp³)-I和C(sp²)-I键的取代基效应. 以及取代碘苯及取代苄基碘化物的远程取代基效应. 此外,在MPWLYP1M方法的基础上研究了典型五元及六元芳香杂环碘化物的C-I键解离焓值.     

衬底温度对类金刚石薄膜力学性能的影响

 采用脉冲激光沉积方法在不同衬底温度下制备了最高硬度与弹性模量分别达45 GPa和290 GPa,且表面十分光滑的类金刚石薄膜。在相对湿度为80%的条件下,薄膜最低的摩擦系数与磨损率分别为0.045与5.74×10^-10 mm³·N^-1·m^-1。实验结果表明,硬度与弹性模量随衬底温度升高而降低,摩擦系数与磨损率随衬底温度升高而增大。拉曼光谱表明:在室温下制备的薄膜为典型类金刚石结构,sp³含量高达76.8%,而随温度升高,薄膜结构逐渐经无定形碳结构向纳米晶石墨结构方向发展,sp³含量也随之降低,力学性能变差。     

非平衡磁控溅射制备类石墨碳膜及性能研究

利用中频非平衡磁控溅射技术在单晶硅基底上沉积了类石墨碳膜, 采用Raman光谱、高分辨透射电子显微镜、原子力显微镜分析了薄膜微观结构和表面形貌; 采用纳米压痕仪和CSM摩擦磨损试验机测试了碳膜力学性能和摩擦学性能. 结果表明: 利用中频非平衡磁控溅射技术沉积的碳膜是一种以sp²键合碳为主、结构非晶、硬度适中、应力较低、表面粗糙度较大、摩擦性能优异的薄膜. 脉冲占空比对薄膜微观结构和性能有显著影响, 随着脉冲占空比的增大, Raman光谱D峰和G峰的强度比I_D/I_G先减小后增大, 而硬度随脉冲占空比的增大却呈现出相反的变化趋势, 即先增大后减小; 大气氛围中的摩擦性能测试表明, 本实验制备的薄膜具有优异的抗磨性能(～10^-11 cm³/N^-1. m^-1)和承载能力(～2.5 GPa). 随脉冲占空比的增大, 薄膜摩擦系数变化甚微而磨损率却呈现先显著减小后轻微增大的变化趋势. 类石墨碳膜优异的摩擦学性能主要归因于其独特的结构、较低的内应力及良好的结构稳定性.     

直流磁控溅射Si和玻璃衬底Fe/Co多层膜的磁性能比较

对直流磁控溅射Si和玻璃衬底［Co_t/Fe_3t］₅(t=2, 3, 4, 5nm)多层膜的磁性能进行了比较.对于t相同但衬底不同的样品，实验发现饱和磁化强度相差很小，但是矫顽力却相差很大.对矫顽力差异的理论分析表明，多层膜的粗糙度和畴壁类型是引起这种差异的主要原因.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.