Measurement of vapor–liquid equilibria (VLE) and excess enthalpies (H) of binary systems with 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide and prediction of these properties and γ using modified UNIFAC (Dortmund)

Vapor–liquid equilibria (VLE) and excess enthalpies (H^E) were measured for a variety of alkanes, alkenes, aromatics, alcohols, ketones and water in several ionic liquids, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [EMIM]⁺[BTI]⁻, 1-butyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)imide [BMIM]⁺[BTI]⁻, 1-hexyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)imide [HMIM]⁺[BTI]⁻ and 1-octyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)imide [OMIM]⁺[BTI]⁻, covering the temperature range from 323.15 to 413.15 K. The new data were used together with the already available experimental data for imidazolium compounds to fit the required group interaction parameters for modified UNIFAC (Dortmund). The results show that in the future modified UNIFAC (Dortmund) can be applied successfully also for systems with ionic liquids.     

Influence of water on the dissolution of cellulose in selected ionic liquids

Cellulose (7% water) was thoroughly dispersed in various ionic liquids (IL) and the turbidity of the mixture was investigated to distinguish real dissolution from fine dispersion. The dissolving ability of 1-butyl-3-methylimidazolium chloride (BMIMCl know cellulose solvent) and 11 other commercial IL (not reported as cellulose solvents) was studied. From the latter, only 1,3-dimethylimidazolium dimethylphosphate (DMIMDMP) could dissolve cellulose. The influence of water content on the real dissolution of cellulose in these two IL was investigated. The maximum theoretical amount of dissolved anhydrous cellulose in the IL was determined by extrapolation methodology at different temperatures. For cellulose in BMIMCl, it was 8.75 g/100 g of IL at 95 °C. DMIMDMP could achieve real cellulose dissolution only in a practically anhydrous system (2.3 g/100 g of IL at 30 °C) but dissolution was physically limited by high viscosity.     

Influence of the ionic liquid structure on thiophene solubility

Binary liquid-liquid equilibria for 10 systems containing an ionic liquid with thiophene were measured by dynamic method in the temperature range from 283 K to the boiling point of thiophene. The influence of ionic liquid structure on solubility of thiophene is discussed in comparison with results taken from the literature. The solubility of thiophene in all investigated ionic liquids is high - below 0.31 ionic liquid mole fraction.     

Measurement and prediction of activity coefficients at infinite dilution (γ), vapor–liquid equilibria (VLE) and excess enthalpies (H) of binary systems with 1,1-dialkyl-pyrrolidinium bis(trifluoromethylsulfonyl)imide using mod. UNIFAC (Dortmund)

Activity coefficients at infinite dilution (γ^∞), vapor–liquid equilibria (VLE) and excess enthalpies (H^E) were measured for alkanes and alkenes in the ionic liquids 1-butyl-1-methyl-pyrrolidinium bis(trifluoromethylsulfonyl)imide [BMPYR]⁺[BTI]⁻, 1-hexyl-1-methyl-pyrrolidinium bis(trifluoromethylsulfonyl)imide [HMPYR]⁺[BTI]⁻ and 1-octyl-1-methyl-pyrrolidinium bis(trifluoromethylsulfonyl)imide [OMPYR]⁺[BTI]⁻.     

色谱分析中离子液体的应用及其测定

离子液体作为一种优良的溶剂越来越受到人们的关注。由于离子液体特殊的物理化学性质使其在色谱分析中也得到了较广泛的应用。本文综述了离子液体在气相色谱、高效液相色谱和毛细管电泳中的应用,其中包括离子液体作为气相色谱的固定相、高效液相色谱的固定相及流动相添加剂和毛细管电泳的电解质添加剂等,并对离子液体的色谱分离检测作了详细介绍。     

Screening the extractability of some typical environmental pollutants by ionic liquids in liquid-phase microextraction

The extractability of some typical environmental pollutants in ionic liquids (ILs) was screened by using a simple one-step liquid phase microextraction procedure. It was demonstrated that 1-alkyl-3-methylimidazolium hexafluorophosphate ([CnMIM][PF6], n = 4, 8), two typical ILs, could effectively extract a set of 45 typical environmental pollutants including BTEX (benzene, toluene, ethylbenzene, and xylene), polycyclic aromatic hydrocarbons, phthalates, phenols, aromatic amines, herbicides, organotin, and organomecury. Analytes in 10 mL sample solution held in a 15 mL vial were extracted by a 5 microL drop of ILs suspended on the needle of a high-performance liquid chromatography (HPLC) microsyringe; this was followed by HPLC, atomic absorption spectrometry, or cold-vapor atomic fluorescence spectrometry determination. The enrichment factors determined were in the range of 5-168 for 15 min extraction by [C4MIM][PF6] and 4-178 for 30 min extraction by [C8MIM][PF6], respectively, which indicates that ILs might be considered as potential environmentally benign alternative recyclable solvents for the enrichment of environmental pollutants.     

A SEM–EDX study of highly stable supported liquid membranes based on ionic liquids

This work evaluates the operational stability of six different supported liquid membranes (SLMs) based on ionic liquids (ILs). [bmim⁺][PF₆⁻]_, [bmim⁺][BF₄⁻] and [bmim⁺][NTf₂⁻] were used as supporting phase in Nylon^® and Mitex^® membranes. Scanning electron microscopy (SEM) combined with energy dispersive X-ray (EDX) analysis was used to characterize the membrane surface morphologically and examine the global chemical composition of the membranes and the distribution of the ILs within them.

Study of the freshly impregnated membranes showed that, in all cases, the ILs were homogeneously distributed, mostly filling the pores of the membranes although, in some cases, a small amount of excess of IL was located on the external membrane surface. Stability tests were performed by keeping the respective impregnated membranes immersed for a week in a diffusion cell including two independent compartments and using n-hexane/n-hexane as the respective feed and receiving phases. The SEM–EDX study of membranes after continuous operation showed that the ILs were still retained within the membrane pores and only small losses of the IL initially located on the external surface were observed. These observations are in complete agreement with the ionic losses determined by mass balance.     

Phase equilibria of imidazolium ionic liquids and the refrigerant gas, 1,1,1,2-tetrafluoroethane (R-134a)

A number of applications with ionic liquids (ILs) and hydrofluorocarbon gases have recently been proposed. Detailed phase equilibria and modeling are needed for their further development. In this work, vapor–liquid equilibrium, vapor–liquid–liquid equilibrium, and mixture critical points of imidazolium ionic liquids with the hydrofluorocarbon refrigerant gas, 1,1,1,2-tetrafluoroethane (R-134a) was measured at temperatures of 25 °C, 50 °C, 75 °C and pressure up to 143 bar. The ionic liquids include 1-hexyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)amide ([HMIm][Tf₂N]), 1-hexyl-3-methyl-imidazolium hexafluorophosphate ([HMIm][PF₆]), and 1-hexyl-3-methyl-imidazolium tetrafluoroborate ([HMIm][BF₄]). The effects of the anion and cation on the solubility were investigated with the anion having greatest impact. [HMIm][Tf₂N] demonstrated the highest solubility of R-134a. The volume expansion and molar volume were also measured for the ILs and R-134a. The Peng–Robinson Equation of State with van der Waals 2-parameter mixing rule with estimated IL critical points were employed to model and correlate the experimental data. The models predict the vapor–liquid equilibrium and vapor–liquid–liquid equilibrium pressure very well. However, the mixture critical points predictions are consistently lower than experimental values.     

Three-component coupling reactions in ionic liquids: One-pot synthesis of isoxazolidines

1-Butyl-3-methylimidazolium based ionic liquids are found to accelerate significantly the intermolecular 1,3-dipolar cycloaddition of nitrones derived in situ from aldehydes and phenyl hydroxylamine, with electron deficient olefins to afford enhanced rates and improved yields of isoxazolidines with high regio- and diastereoselectivity.     

Correlation of solubility data of ammonia in ionic liquids for gas separation processes using artificial neural networks

Artificial neural networks have been used for the correlation and prediction of solubility data of ammonia in ionic liquids. This solubility of ammonia is highly variable for different types of ionic liquids at the same temperature and pressure, its correlation and prediction is of special importance in the removal of ammonia from flue gases for which effective and efficient solvents are required. Nine binary ammonia + ionic liquids mixtures were considered in the study. Solubility data (P–T–x) of these systems were taken from the literature (208 data points for training and 50 data points for testing). The training variables are the temperature and the pressure of the binary systems (T, P), being the target variable the solubility of ammonia in the ionic liquid (x). The study shows that the neural network model is a good alternative method for the estimation of solubility for this type of mixtures. Absolute average deviations were below 5.6%, for each isothermal data set and overall absolute average deviations were below 3.0%. Only in the range of low solubility (below 0.2 in mole fraction) did predicted solubility give deviations higher than 10%.     

Green approach for the conversion of olefins into vic-halohydrins using N-halosuccinimides in ionic liquids

Alkenes undergo smooth bromo- and iodohydroxylation with N-bromo- and N-iodosuccinimides/water, respectively, using the air and moisture stable ionic liquid [bmim]BF₄ as a novel recyclable reaction medium in high to quantitative yields. N-Halosuccinimides show enhanced reactivity in ionic liquids thereby reducing the reaction times and improving the yields considerably.     

Zero solvent emission process for sulfur dioxide recovery using a membrane contactor and ionic liquids

Selective absorption into a liquid is a widespread method to separate and concentrate sulfur dioxide from gas emissions, reducing air pollution and environmental risks. Process intensification can be performed first by the substitution of the equipment (e.g. scrubbers) for a membrane device to avoid drops dragging, and second by the substitution of the absorption solvent (e.g. N,N-dimethylaniline) for ionic liquids to avoid solvent volatilization. According to this intensification, a zero solvent emission process has been developed.The ionic liquid 1-ethyl-3-methylimidazolium ethylsulfate is used as the absorption solvent and the results are compared to the N,N-dimethylaniline results. A ceramic hollow fibre module is the membrane device where the sulfur dioxide absorption takes place. A gas stream with a typical composition of roasting effluents flows through the shell side and the absorption liquid flows counter currently by the inside of the hollow fibres. The influence of carbon dioxide in the absorption is also evaluated and the overall mass transfer coefficients are calculated. The difference between the estimated mass transfer coefficients and the experimental results for both solvents is discussed assuming partial wetting of the membrane.     

Measurement and correlation of vapor pressure of benzene and thiophene with [BMIM][PF6] and [BMIM][BF4] ionic liquids

An apparatus used to measure vapor pressure of organic solvents was set up, and vapor pressure of mixture of ionic liquids ([BMIM][PF₆] and [BMIM][BF₄]) and aromatic compounds (benzene and thiophene), with mole fraction of organic solute from 0.1 to 0.75 was measured by using saturation vapor pressure method at temperature from 303 K to 343 K. Then NRTL equation was used to correlate the experimental data. The overall average relative deviation of activity coefficients for the whole system is 2.30%, which indicates that NTRL equation can be utilized to correlate vapor pressure of binary systems containing ionic liquids. The results show that ionic liquids can depress the volatility of aromatic compounds.     

Impact of ionic liquids on silver thermoplastic polyurethane composite membranes for propane/propylene separation

This work describes newly synthesized composite polymeric membranes and their utilization in propane/propylene separation in a gas mixture. The nonporous composite polymers were successfully synthesized by using thermoplastic polyurethane (TPU) and several silver salts/silver salts with ionic liquids (ILs). Our studies showed that silver bis(trifluoromethanesulfonyl)imide (Ag[Tf₂N]) containing membranes outperformed other silver salt containing membranes in terms of selectivity. In addition, to this finding, ILs, as additives for the membranes, enhanced the selectivity by facilitating improved coordination of the olefin with the silver ions in the dense composite polymers.     

Magnetic ionic liquids as non-conventional extraction solvents for the determination of polycyclic aromatic hydrocarbons

This work describes the applicability of magnetic ionic liquids (MILs) in the analytical determination of a group of heavy polycyclic aromatic hydrocarbons. Three different MILs, namely, benzyltrioctylammonium bromotrichloroferrate (III) (MIL A), methoxybenzyltrioctylammonium bromotrichloroferrate (III) (MIL B), and 1,12-di(3-benzylbenzimidazolium) dodecane bis[(trifluoromethyl)sulfonyl)]imide bromotrichloroferrate (III) (MIL C), were designed to exhibit hydrophobic properties, and their performance examined in a microextraction method for hydrophobic analytes. The magnet-assisted approach with these MILs was performed in combination with high performance liquid chromatography and fluorescence detection. The study of the extraction performance showed that MIL A was the most suitable solvent for the extraction of polycyclic aromatic hydrocarbons and under optimum conditions the fast extraction step required ∼20 μL of MIL A for 10 mL of aqueous sample, 24 mmol L⁻¹ NaOH, high ionic strength content of NaCl (25% (w/v)), 500 μL of acetone as dispersive solvent, and 5 min of vortex. The desorption step required the aid of an external magnetic field with a strong NdFeB magnet (the separation requires few seconds), two back-extraction steps for polycyclic aromatic hydrocarbons retained in the MIL droplet with n-hexane, evaporation and reconstitution with acetonitrile. The overall method presented limits of detection down to 5 ng L⁻¹, relative recoveries ranging from 91.5 to 119%, and inter-day reproducibility values (expressed as relative standard derivation) lower than 16.4% for a spiked level of 0.4 μg L⁻¹ (n = 9). The method was also applied for the analysis of real samples, including tap water, wastewater, and tea infusion.     

Evaporation of ionic liquids at atmospheric pressure: study by ion mobility spectrometry

A conventional ion mobility spectrometry (IMS) was used to study atmospheric pressure evaporation of seven pure imidazolium and pyrrolidinium ionic liquids (ILs) with [Tf₂N], [PF₆], [BF₄] and [fap] anions. The positive drift time spectra of the as-received samples measured at 220 °C exhibited close similarity; the peak at reduced mobility K₀ = 1.99 cm² V⁻¹ s⁻¹ was a dominant spectral pattern of imidazolium-based ILs. With an assumption that ILs vapor consists mainly of neutral ion pairs, which generate the parent cations in the reactant section of the detector, and using the reference data on the electrical mobility of ILs cations and clusters, this peak was attributed to the parent cation [emim]. Despite visible change in color of the majority of ILs after the heating at 220 °C for 5 h, essential distinctions between spectra of the as-received and heated samples were not observed. In negative mode, pronounced peaks were registered only for ILs with [fap] anion.     

Glycolysis of poly(ethylene terephthalate) catalyzed by ionic liquids

Poly(ethylene terephthalate) (PET) from an industrial manufacturer was depolymerized by ethylene glycol in the presence of a novel catalyst: ionic liquids. It was found that the purification process of the products in the glycolysis catalyzed by ionic liquids was simpler than that catalyzed by traditional compounds, such as metal acetate. Qualitative analysis showed that the main product in the glycolysis process was the bis(hydroxyethyl) terephthalate (BHET) monomer. Thermal analysis of the glycolysis products was carried out by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The influences of experimental parameters, such as the amount of catalyst, glycolysis time, reaction temperature, and water content in the catalyst on the conversion of PET, selectivity of BHET, and distribution of the products were investigated. Results show that reaction temperature is a critical factor in this process. In addition, a detailed reaction mechanism of the glycolysis of PET was proposed.     

Application of ionic liquids based microwave-assisted simultaneous extraction of carnosic acid, rosmarinic acid and essential oil from Rosmarinus officinalis

An ionic liquid based microwave-assisted simultaneous extraction and distillation (ILMSED) method has been developed for the effective extraction of carnosic acid (CA), rosmarinic acid (RA) and essential oil (EO) from Rosmarinus officinalis. A series of 1-alkyl-3-methylimidazolium ionic liquids differing in composition of anion and cation were evaluated for extraction yield in this work. The results obtained indicated that the anions and cations of ionic liquids had influences on the extraction of CA and RA, 1.0M 1-octyl-3-methylimidazolium bromide ([C8mim]Br) solution was selected as solvent. In addition, the ILMSED procedures for the three target ingredients were optimized and compared with other conventional extraction techniques. ILMSED gave the best result due to the highest extraction yield within the shortest extraction time for CA and RA. The novel process developed offered advantages in term of yield and selectivity of EO and shorter isolation time (20 min in comparison of 4h of hydrodistillation), and provides a more valuable EO (with high amount of oxygenated compounds). The microstructures and chemical structures of rosemary samples before and after extraction were also investigated. Moreover, the proposed method was validated by the stability, repeatability and recovery experiments. The results indicated that the developed ILMSED method provided a good alternative for the both extraction of non-volatile compounds (CA and RA) and EO from rosemary as well as other herbs.     

Spectroelectrochemical characterization of thin fullerene films in room temperature ionic liquids

Room-temperature ionic liquids were used as electrolytes for in situ studies of the transitions of solution cast fullerene films. 1-Butyl-3-methyl-imidazolium tetrafluoroborate (BMIMBF₄), 1-butyl-3-methyl-imidazolium hexafluorophosphate (BMIMPF₆) and 1-butyl-2,3-dimethylimidazolium tetrafluoroborate (BDiMIMBF₄) were used in this study and the techniques used are cyclic voltammetry and in situ attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Infrared spectra were recorded during the reversible redox processes of the C₆₀ films showing a three-step one electron reduction and reoxidation reaction. After reoxidation some part of the C₆₀ film remained in its form. The IR bands obtained during electrochemical reduction of C₆₀ in ionic liquids were compared with the spectra reported for C₆₀ films upon reduction in the presence of different cations in organic solutions.