燃烧辅助合成LiNi0.05Mn1.95O4粉体及其性质研究

以醋酸锂、醋酸锰、硝酸镍、柠檬酸、乙二醇为原料,采用燃烧辅助合成锂离子电池正极材料LiNi0.05Mn1.95O4。采用X射线衍射、扫描电子显微镜、循环伏安、恒电流充放电等技术对合成产物进行物相、形貌及电化学性能分析与测试。结果表明:采用燃烧辅助合成LiNi0.05Mn1.95O4过程中,前驱体在空气中点燃后已形成单一尖晶石相,经750℃热处理4 h后得到的LiNi0.05Mn1.95O4粉末X射线衍射峰尖锐,结晶性好,晶粒尺寸均匀。该法合成的LiNi0.05Mn1.95O4粉末首次放电比容量为117.5 mAh.g-1,经50次充放电循环后的容量保持率为95.1%,合成的LiNi0.05Mn1.95O4粉末具有良好的电化学性能。     

喷雾干燥法制备锂离子电池正极材料LiNi0.5Mn1.5O4及其电化学性能研究

以氢氧化锂,乙酸锰,乙酸镍为原料,采用一次喷雾干燥法合成了LiNi0.5Mn1.5O4前驱体.研究了烧结温度和退火温度对LiNi0.5Mn1.5O4晶形结构、形貌以及电化学性能的影响,采用X射线衍射(XRD)仪、扫描电镜(SEM)对其晶体结构和微观形貌进行表征.结果表明,在900℃下焙烧20 h,600℃下退火30 h合成的LiNi0.5 Mn1.5O4为结晶良好的尖晶石结构,颗粒具有规则的八面体形貌,由粒径在2 μm左右的小颗粒堆积而成.该样品在室温0.1C.倍率下的首次放电容量为133.7 mAh·g-1,循环50次后的容量为123.1 mAh·g-1.     

热处理温度对溶胶凝胶法制备LiNi0.5Mn1.5O4电化学性能的影响

在传统溶胶凝胶法的基础上,通过高温热处理LiNi0.5Mn1.5O4前驱体,合成了高性能的LiNi0.5Mn1.5O4材料.通过X射线衍射仪测试材料的结构,经过超高温热处理后,获得了晶体发育完好的LiNi0.5Mn1.5O4.经电化学测试,高温热处理显著提高了材料的循环性能.经过900℃处理的LiNi0.5Mn1.5O4首次充放电容量达到123 mAh/g,在1C倍率下循环一百次以后容量仍在121.6 mAh/g左右,容量保持率达到98.9;,高温热处理显著的改善了材料的循环性能.     

自模板法合成5V尖晶石LiNio.5Mn1.5O4正极材料及电化学性能研究

通过自模板法采用马来酸酐与丙烯酸接枝共聚得到改性聚丙烯酸碳酸盐前驱体,模板结构呈交联网状稳固致密,高温烧结制得5V锂离子电池LiNi0.5Mn1.5O4正极材料.经XRD、SEM、恒电流充放电和电化学循环伏安测试,所得材料具有微纳米结构,晶型规则,粒径大小一致.工作平台为4.7V,在0.5C倍率下充放电循环测试,首次放电容量132 mAh/g,循环50次容量保持率为93;,电化学性能优良.     

超声波辅助固液反应球磨制备ZnFe2O4纳米晶的研究

以α-Fe2O3和ZnO粉体为原料,在超声波辅助高能球磨作用下通过诱发固液相反应,并在低温下烧结合成了ZnFe2O4纳米晶粉末.采用X射线、透射电镜(TEM)对前驱体和烧结产物进行了表征,分析了球磨过程对粉体晶粒尺寸的影响和znFe2O4的形成过程.实验结果表明:超声波辅助固液球磨能在低温下烧结合成ZnFe2O4纳米晶,纳米晶的晶粒尺寸为15～25 nm;相比无超声波辅助下的固液球磨,超声波球磨降低znFe2O4烧结温度约50℃;同一烧结温度下,球磨时间越长,ZnFe2O4转化率越高,晶粒尺寸越小.     

水热法生长立方MgO微晶研究

以尿素与Mg(NO3)2·6H2O在不同的反应温度和不同物质的量配比条件下,制备出前驱体Mg5(OH)2(CO3)4·4H2O/MgCO3,经煅烧得到立方MgO微晶粉末.利用X射线衍射仪(XRD)和扫描电子显微镜(SEM)对所制得产物的晶相和形貌进行了表征.结果表明:当尿素和Mg(NO3)2·6H2O物质的量的比为2∶1时,在160℃的水热反应条件下,制备出立方MgO前驱体微晶,在1000℃煅烧2h后能够获得晶型完整、形貌规则、粒径约为5μm的MgO立方微晶.     

负极材料Li4Ti5O12的制备与性能研究

利用纳米二氧化钛(P25)粉为钛源,Li2CO3为锂源,采用固相法及高能球磨法制备亚微米级尖晶石Li4Ti5O12.将Li4Ti5O12与碳纳米管(CNTs)制备成复合电极作为工作电极与锂片组成电池进行电化学性能测试.通过SEM,XRD等表征材料形貌、结构及粒径分布,通过充放电测试表征其电化学性能.结果表明,在800℃合成温度及8h合成时间制备条件下可以得到小尺寸且颗粒均匀的亚微米晶体Li4Ti5O12,且合成的产物电化学性能最佳.在800℃及8h合成条件下,产物首次充放电容量分别为188.0 mAh/g和189.1 mAh/g,首次充放效率为99.4％,且具有良好的可逆性.     

非水解和水解溶胶-凝胶法合成MgAl2O4粉体对比研究

分别采用非水解和水解溶胶-凝胶法制备MgAl2O4粉体,利用DTA-TG、XRD和FE-SEM等研究了凝胶煅烧过程中的相变化、粉体形貌及其烧结性能.研究表明,水解凝胶经900℃煅烧0.5h后可形成大量镁铝尖晶石晶相,但仍有少量的方镁石相存在,非水解凝胶经900℃煅烧0.5h后只有镁铝尖晶石晶相.采用水解和非水解法所合成MgAl2O4粉体的平均粒径分别为90nm和50 nm,其经1600℃烧结3h后晶粒尺寸分别为1～2 μm和0.5 ～1μm,晶粒多呈八面体形状,相比之下,采用水解法时MgAl2O4晶体发育较好,出现了明显的生长台阶.     

氯化铵对AACH热分解制备纳米α-Al2O3的影响

以硫酸铝铵和碳酸氢铵为主要原料,采用沉淀法制备纳米碳酸铝铵(AACH)前驱体,通过碳酸铝铵热分解制备α-Al2O3,并利用X射线衍射(XRD),透射电镜(TEM)对前驱体及其煅烧产物的物相和形貌进行表征.研究表明通过添加氯化铵能够降低α-Al2O3的相变温度,并且随着加入量的增加,颗粒粒径减小,分散性改善.加入10;氯化铵的前驱体在1150 ℃下煅烧1 h后可以得到分散性较好的纳米α-Al2O3颗粒.     

低温燃烧合成法制备纳米氧化镧

以六水硝酸镧、一水柠檬酸为原料,利用低温燃烧合成法制备了纳米La2O3粉体.利用XRD、TG-DTA和TEM等测试方法对干凝胶热分解过程及最终形成的纳米La2O3粉体进行了表征,并研究了前驱体溶液的pH值、物质的量配比、煅烧温度、煅烧时间对粉体粒径和形貌的影响.实验结果表明,在溶液的pH=2,La(NO3)3·6H2O:C6H8O7·H2O=6:7,煅烧温度在700~900 ℃,煅烧时间为1.5 h时,可获得粒径均匀的纳米La2O3粉体,且所得产物的粒径范围为50~100 nm.     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

First-principles coexistence simulations of supercooled liquid silicon

We perform first-principles coexistence simulations of the low-density and the high-density phases of supercooled liquid silicon and find a negative slope for the coexisting line in the temperature-pressure plane. Electron density maps and electron-localization function plots of the two phases of silicon show marked differences. The calculated differences suggest more localized electrons in the low-density liquid compared to the high-density liquid, coming from an increased population of covalent bonds, which further explain the calculated negative slope in the two phase coexistence regime. This is consistent with the presence of a pseudo-gap in low-density liquid silicon, absent in the high-density liquid which shows a metallic behavior.     

Crystal structures of thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane

Structures of both thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane, ?C₆H₄?CH₂SCH₂?C₆H₁₀?CH₂SCH₂?, have been determined, wherecis andtrans refer to the attachments to the cyclohexane ring. Thecis form crystallizes in the monoclinic space groupP2₁/c witha=8.4299(11)Å,b=21.772(2)Å,c=8.9724(13)Å, β=116.574(11)^o, andZ=4. Thetrans isomer packs into the monoclinic space groupP2₁ witha=8.159(16)Å,b=10.185(5)Å,c=9.558(2)Å, β=112.435(18)^o, andZ=2. The cyclohexane ring of thecis isomer is in the chair conformation, while the cyclohexane of thetrans isomer is found in a twisted boat conformation.     

CTAB与SDBS对碳酸锶粒子生长形态调控及机理研究

以表面活性剂CTAB和SDBS为化学添加剂,采用化学共沉淀法对碳酸锶晶体的生长形态进行调控,成功地制备出了实心的树枝状和花瓣为空心的花状碳酸锶粉体,并用X射线衍射(XRD)、扫描电子显微镜(SEM)和傅里叶变换红外光谱(FT-IR)等分析手段对样品进行了表征;最后重点对化学添加剂可能产生的影响机理进行了初步的探讨.结果表明,CTAB和SDBS在晶体生长的过程中能起到显著的影响作用,两者对粒子分散性能的作用效果相反,而且后者对晶体(013)和(213)晶面表面能降低的贡献明显大于前者.     

Crystal structures of the cis and trans isomers of a tetrathia[3.3.3.3]cyclophane

Both the cis and trans isomers of 3,11,18,26-tetrathiatricyclo[26.2.2.1^5,9.2^13,16.1^20,24] hexatriaconta-5,7,9,20,22,24-hexene have been prepared and structurally characterized. Each of these centrosymmetric tetrathia dimers includes two cyclohexane rings in chair conformations with either 1,4-cis or 1,4-trans bonding and two meta-substituted benzene rings. The cis isomer packs into the monoclinic space group P2₁/a with a = 10.485(3)Å, b = 10.3956(18)Å, c = 14.1343(10)Å, = 105.200(13)°, Z = 2 and refined to an R factor of 0.046. The trans isomer crystallizes in the monoclinic space group P2₁/c with a = 10.7217(12)Å, b = 5.6797(7)Å, c = 25.415(5)Å, = 96.001(12)°, Z = 2 and refined to an R factor of 0.043. In the cis structure each benzene ring faces a cyclohexane ring while in the trans structure the cyclohexane rings face one another.     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

Synthesis and Crystal Structure of 5-[2-(6-bromonaphthalenyloxymethyl)]-3-(4-morpholinomethyl)-1,3,4-oxadiazole-2(3<Emphasis Type="Italic">H</Emphasis>)-thione

Abstract  The title compound, C₁₈H₁₈BrN₃O₃S, a derivative of 1,3,4-oxadiazole, crystallizes in the triclinic space group P-1 with unit cell parameters a = 6.8731(3), b = 8.9994(4), c = 15.7099(6) ?, α = 92.779(3)°, β = 130.575(3)°, γ = 107.868(4)°, Z = 2. The dihedral angle between the mean planes of the planar naphthyl and morpholine (chair) rings with the planar oxadiazol ring is 50.1(8) and 76.8(6)°, respectively. The planar naphthyl ring is twisted 52.2(5)° with the mean plane of the morpholine ring. A group of four intermolecular close contacts are observed between a bromine atom and hydrogen atoms from the closely packed naphthyl, morpholine and oxy–methyl groups in the unit cell. These molecular interactions in concert with an additional series of π–π stacking interactions that occur between the center of gravity of the two 6-membered rings of the naphthalene group influence the twist angles of each of these three groups. A MOPAC AM1 calculation of the conformation energy of the crystal structure [226.0128(9) kcal] compared to that of the minimum energy structure after geometry optimization [29.9744(1) kcal] reveals a significantly reduced value. The twist angles of the three groups above also change after the AM1 calculation giving support to the influence of both intermolecular C–H···Br short-range interactions and Cg π–π stacking interactions on these angles which therefore play a role in stabilizing crystal packing. Graphical Abstract  Crystal structure of 5-{[(6-bromonaphthalen-2-yl)oxy]methyl}-3-(morpholin-4-ylmethyl)-1,3,4-oxadiazole-2(3H)-thione, C₁₈H₁₈BrN₃O₃S, is reported and its geometric and packing parameters described and compared to a MOPAC computational calculation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

电沉积法制备ZnO纳米棒阵列及其发光特性

本文以掺F的SnO2导电玻璃为基板,以硝酸锌水溶液为电解液,采用三电极恒电位体系电沉积制备ZnO纳米棒阵列,系统考察了硝酸锌浓度和沉积电位等工艺参数对ZnO纳米棒阵列的微观形貌及其发光性能的影响规律.结果表明,硝酸锌浓度和沉积电位对纳米棒阵列的形貌有显著影响,控制适宜的工艺条件可以制备出直径分布均匀、结晶性好且纯度高的六方纤锌矿ZnO纳米棒阵列.荧光光谱分析表明,电沉积制备出的ZnO纳米棒阵列在385 nm附近有一个强荧光发射峰,且发光性能稳定、对纳米棒阵列微观形貌的细微变化不敏感,使其在发光二极管和激光器等领域具有广阔的应用前景.     

Crystal structure of irisolidone from the flowers of Pueraia lobata

Irisolidone (5,7-dihydroxy-6,4′-dimethoxyisoflavone) was isolated from the flowers of Pueraia lobata and its crystal structure was examined by X-ray single crystal diffraction. The crystal structure of irisolidone is monoclinic, space group P2₁/c with a = 15.491(9) ?, b = 7.895(4) ?, c = 13.321(7) ?, β = 110.546(9)° and Z = 4. Hydrogen bonding and aromatic π–π stacking assemble the title compound into a three-dimensional networking structure.