CaO对MgO-Al2O3-SiO2系微晶玻璃结构与性能的影响

以化学纯试剂为原料,采用熔融法制备MgO-Al2O3-SiO2(MAS)系微晶玻璃.利用DSC、XRD、SEM等及理化性能测试手段研究了不同CaO含量对微晶玻璃析晶行为、物相组成、显微结构及理化性能的影响.结果表明:一定含量的CaO可以降低析晶活化能,促进玻璃析晶;随CaO含量的增加,微晶玻璃主晶相由假蓝宝石向α-堇青石转变,晶体形貌由棒状晶转变为枝状晶,晶粒尺寸呈先减后增的趋势;当CaO含量为3wt;时微晶玻璃热膨胀系数和相对介电常数(εr)达到最低,分别为3.89×10-1℃-1和10.09(1 MHz);当不外添CaO时微晶玻璃Vickers硬度达到最大,为10.52 GPa.     

Fe2O3对MgO-Al2O3-SiO2系微晶玻璃介电性能的影响

以化学纯试剂为原料采用高温熔融法制备MgO-Al2O3-SiO2 (MAS)系微晶玻璃,利用差热分析仪(DSC)、X射线衍射(XRD)、电子扫描显微镜(SEM)以及介电检测等手段对Fe2O3在MAS系微晶玻璃中介电性能的影响进行探究.结果表明:Fe2O3有降低微晶玻璃核化和晶化温度的作用;随着Fe2O3的加入,试样的主晶相由堇青石向镁铝尖晶石转变,试样的介电常数和介电损耗逐渐减小并且电阻率增高;当Fe2O3的添加量大于6;时,微晶玻璃的介电性能变化不大,趋于稳定.     

Fe2O3对CaO-Al2O3-MgO-SiO2系微晶玻璃析晶及断裂特性的影响

采用熔融法,利用纯化学试剂制备了CaO-A12O3-MgO-SiO2 (CAMS)系微晶玻璃,利用DTA、XRD、拉曼光谱仪等研究了Fe2O3对微晶玻璃析晶特性的影响规律,微晶玻璃的物化性能由抗折强度、杨氏模量、剪切模量、泊松比、维氏硬度等进行评价.结果表明,微晶玻璃的析晶特性随着Fe2 O3含量的增加而增强,对应母体玻璃中首先出现富铁相,进而促进辉石主晶相的析出.微晶玻璃的断裂特性及裂纹扩展方式均随析晶度的提高得到明显改善.但过量的Fe2O3添加则对微晶玻璃的析晶特性无明显影响,反而降低了玻璃相的致密性.微晶玻璃的耐酸性、抗折强度、杨氏模量及剪切模量均呈现先增加后降低的趋势,微晶玻璃的Fe2 O3含量为6.6wt;时综合性能最优.     

高热膨胀Na2O-MgO-Al2O3-SiO2微晶玻璃的制备及性能研究

采用传统熔体冷却法制备了Na2O-MgO-Al2 O3-SiO2玻璃并采用整体析晶工艺制备了微晶玻璃.利用DSC、XRD、SEM等测试手段研究了微晶玻璃的析晶行为和显微结构,探讨了热处理制度对该体系微晶玻璃热膨胀系数、密度、抗弯强度、显微硬度等性能的影响.研究结果表明,当晶化温度为800℃时该体系微晶玻璃主晶相为颗粒状霞石晶体(NaAlSiO4);当晶化温度达到900℃时玻璃中开始析出镁橄榄石(Mg2SiO4)晶体;延长保温时间可显著促进析晶但对晶体种类没有影响.析晶后微晶玻璃的密度、热膨胀系数、抗弯强度和显微硬度值显著增加,其最高热膨胀系数可达14.1×10-6℃-1.所制备的微晶玻璃具有很好的机械性能,当热处理温度为1000℃时,其抗弯强度和显微硬度分别达160 MPa和7.8 GPa.     

Cr2O3对白云鄂博西尾矿微晶玻璃显微结构及性能的影响

以白云鄂博西尾矿和粉煤灰为主要原料,采用熔融法制备了添加0～2.0wt; Cr2O3的CaO-MgO-SiO2-Al2O3系微晶玻璃,利用DTA、XRD、FESEM、EDS和综合力学性能仪等测试手段,研究了Cr2O3含量对该体系微晶玻璃显微结构及性能的影响.实验结果表明:少量Cr2O3 (0.5wt;)可有效降低样品的晶化温度,促进主晶相辉石相(Ca(Mg,Fe,Al) (Si,Al)2O6)的形成,同时细化其显微组织,从而提高样品的密度、抗折强度和耐酸碱性;当Cr2O3含量大于等于1.5wt;时,析晶峰温度由804℃提高到816℃,同时微晶玻璃中形成不规则块状结构的镁铁铬尖晶石(MgFeo.9 Cr1.1O4)第二相,并进而引起周围辉石相晶粒异常长大,降低其抗折强度.     

P2O5对CaO-MgO-Al2O3-SiO2系微晶玻璃析晶的影响

采用熔融法制备了不同P2O5含量的CaO-MgO-Al2O3-SiO2玻璃样品,研究了P2O5对该系微晶玻璃析晶的影响规律.结果表明:在所研究的CaO-MgO-Al2O3-SiO2玻璃中,P2O5的最大溶解量在10.0;质量分数左右,超过其饱和溶解度后将析出α-磷酸钙相.玻璃中添加4.0;质量分数P2O5时以表面析晶为主,析出晶体为钙长石和少量硅灰石.随着P2O5含量的提高, α-磷酸钙逐渐析出,同时钙长石和硅灰石的析出逐渐降低.进一步提高P2O5含量抑制了玻璃的表面析晶,促进了玻璃的分相和整体析晶.当P2O5的含量达到10;时,玻璃以整体析晶为主,在分相区内外区域析出晶体的形态非常相似,均呈现为细小粒状.     

CaO-MgO-Al2O3-SiO2-P2O5-(F)微晶玻璃的析晶及特征

采用熔融法制备了不同P2O5及F含量的CaO-MgO-Al2O3-SiO2-P2O5-(F)基础玻璃试样,研究了CaO-MgO- Al2O3-SiO2-P2O5-(F)系微晶玻璃的析晶及特征.结果表明:在CaO-MgO-Al2O3-SiO2-8.0wt;P2O5玻璃中,表面析晶和内部析晶同时存在,析出晶体主要为钙长石(CaAl2Si2O8)相、硅灰石(CaSiO3)和α-磷酸钙(Ca3(PO4)2).玻璃中P2O5含量的提高抑制玻璃的表面析晶,同时促进了玻璃的整体析晶和α-磷酸钙晶体析出.同时添加P2O5和F的玻璃试样以整体析晶为主,析出晶体为块状氟磷灰石和粒状钙长石相.     

Fe2O3对纳米晶尾矿微晶玻璃结构及性能的影响

以铁尾矿和金尾矿为主要原料,采用熔融法制备了添加0 ～ 20wt; Fe2O3的CaO-MgO-Al2O3-SiO2(CMAS)系纳米晶尾矿微晶玻璃,利用差示扫描量热分析(DSC)、X射线衍射分析(XRD)、红外光谱(IR)、扫描电镜(SEM)和综合力学性能仪等测试手段,研究了Fe2O3含量对该体系微晶玻璃显微结构及性能的影响.实验结果表明:随着Fe2O3含量的增加,样品的晶化温度和玻璃化转变温度逐渐降低;且Fe2O3可促进主晶相透辉石相(Mg0.6Fe0.2Al0.2) Ca(Si1.5Al1.5)O6的形成;同时Fe2O3能够有效减小透辉石相平均晶粒尺寸;另外,微晶玻璃的密度、显微硬度和耐碱性随晶粒尺寸的减小而增加,而抗折强度和耐酸性随晶粒尺寸的减小而降低.     

铁含量及价态对白云鄂博尾矿微晶玻璃析晶特性及性能的影响

以白云鄂博尾矿及粉煤灰等固体废弃物为主要原料,采用熔融法、经退火、核化及晶化热处理制备得到了以辉石为主晶相的CaO-MgO-Al2O3-SiO2 (CMAS)系尾矿微晶玻璃.利用化学分析方法测定了不同氧化铁及碳含量对微晶玻璃中Fe3+/Fe2+的影响;利用XRD、DTA、SEM等研究了不同氧化铁及碳含量对微晶玻璃结构及析晶特性的影响.结果表明,不同氧化铁添加量对微晶玻璃中Fe3+/Fe2影响很小,因此对微晶玻璃的析晶特性无本质影响.而随着还原碳粉的加入,Fe3+/Fe2与未加碳粉相比减小明显,微晶玻璃中FeO质量分数的增加极大地提高了微晶玻璃的析晶特性.但过量的碳粉加入导致单质铁的析出,反而降低了微晶玻璃的析晶能力.上述析晶特性的变化直接影响到微晶玻璃的耐酸度及抗折强度.     

基础成分配比对白云鄂博尾矿微晶玻璃结构及性能的影响

以白云鄂博二次选后尾矿和粉煤灰为主要原料,采用熔融法制备得到了CaO-MgO-Al2O3-SiO2系尾矿微晶玻璃.制备流程包括熔融、退火、核化及晶化过程.其中玻璃熔融温度为1450℃,核化温度为720℃,晶化温度为850℃.利用XRD研究了基础玻璃成分配比对微晶玻璃结构的影响.结果表明基础玻璃成分配比直接决定微晶玻璃的主晶相形成.随着基础玻璃成分配比的变化,微晶玻璃可能形成辉石相、钙长石相、镁铁尖晶石相或磁铁矿相.当其他元素固定,CaO/MgO和CaO/Al2O3比值的减小会导致微晶玻璃由辉石相转变为镁铁尖晶石相和钙长石相.而当SiO2/CaO比值大于2时,主晶相则由辉石相转变为磁铁矿相.DTA测试结果表明CaO有利于析晶温度的降低,而MgO、Al2O3和SiO2相对提高了析晶温度.力学性能测试表明抗折强度、密度、耐酸碱度与微晶玻璃主晶相有直接关系.主晶相为辉石相的微晶玻璃具有更高的抗折强度、密度和耐酸性.     

CaO-MgO-Al2O3-Fe2O3-B2O3-SiO2系微晶釉的制备

通过引入B2O3以降低烧成温度,利用赤泥中的Fe2O3为着色剂,在1150℃左右低温烧成制备了CaO-MgO-Al2O3-Fe2O3-B2O3-SiO2系微晶釉.赤泥的加入量为20;左右时,釉面具有良好的装饰效果和显微硬度.利用XRD、SEM研究了釉的物相及显微组织.结果表明,釉中析出的微晶是普通辉石,微晶的含量随MgO及CaO的含量增加而增加,而提高Al2O3含量则抑制微晶的析出.     

Pr2O3对含Cr2O3辉石系矿渣微晶玻璃晶化行为的影响

以白云鄂博西尾矿和粉煤灰为主要原料,分别制备了添加0,2.0wt;,4.0wt;和6.0wt; Pr2O3的辉石系矿渣微晶玻璃;综合采用基于DSC/DTA结果的析晶活化能Ek、Avrami指数以及粘流活化能Eη和背散射电子SEM显微形貌分析研究了Pr2O3对析晶的影响.结果表明在所研究范围内,Pr2O3含量的提高在整体上抑制了辉石相的析出.其原因除了与富Pr颗粒相对辉石相在析晶过程中的“钉扎”有关外,还与Pr2O3含量提高后使基础玻璃网络聚合程度加大,从而增大了辉石相形成所需离子扩散的阻力有关.     

Fe2O3-CO3O4共掺杂MgO-Al2O3-SiO2体系的红外辐射性能研究

采用固相反应法制备Fe2O3-Co3O4共掺杂MgO-Al2O3-SiO2体系的复合陶瓷材料,并通过XRD、SEM、XPS以及红外辐射测试等方法研究了样品的结晶行为与红外辐射性能.结果表明:Fe2 O3和Co3 O4共掺杂MgO-Al2 O3-SiO2体系后离子分布改变并生成混合尖晶石,从而引起品格畸变,从而有效提高材料的红外辐射性能.材料的红外发射率与其晶格畸变程度具有相同的变化趋势,并随Fe2 O3与Co3O4质量之比(R)的增加呈非线性变化.当R=3∶2时,材料在8 ～ 14 μm波段的辐射率可达0.92.     

EPR and magnetic susceptibility studies of B2O3–Bi2O3–Gd2O3 glasses

Glasses of the xGd₂O₃ · (100 − x)[B₂O₃ · Bi₂O₃] system with 0.5 ⩽ x ⩽ 10 mol% were studied by electron paramagnetic resonance (EPR) and magnetic susceptibility measurements. Data obtained show that for low gadolinium oxide contents of the samples (x ⩽ 3 mol%) the Gd³⁺ ions are randomly distributed in the host glass matrix and are present as isolated and dipole–dipole coupled species. For higher gadolinium oxide contents of the samples (x > 3 mol%) the Gd³⁺ ions appear as both isolated and antiferromagnetically coupled species. The EPR spectra of the glasses reveal resonance sites with an unexpected high crystalline field in addition to the ‘U’ spectrum, typical for Gd³⁺ ions in disordered systems. This absorption line is due to Gd³⁺ ions that replace Bi³⁺ ions from the host glass matrix and could play the network unconventional former role in the studied glasses.     

Yb2O3-Y2O3-Gd2O3-ZrO2热障涂层制备及性能研究

以Yb2O3、Y2O3 、Gd2O3稀土氧化物粉末和ZrOCl2·8H2O粉末为原料,采用化学共沉淀法制备了Yb2O3-Y2O3-Gd2O3-ZrO2 (YYGZO)热喷涂用粉末,采用大气等离子喷涂技术制备了YYGZO涂层,利用场发射扫描电镜(FESEM)、X射线衍射(XRD)研究了YYGZO粉末及涂层的微观组织形貌、相结构.结果表明,制备的热喷涂YYGZO粉末大部分呈规则实心球体状,且球形度良好,颗粒粒径均匀,大部分颗粒粒径分布为30～60μm,流动性能较好,满足大气等离子喷涂的要求.YYGZO涂层具有较好的高温相结构稳定性.所制备YYGZO热障涂层组织结构比较致密,涂层各个界面结合紧密,孔隙率约为9.23;,结合强度为35.2 MPa.     

Thermal expansion and transition temperature of glasses in the systems BeO–Al2O3–B2O3 and MgO–Al2O3–B2O3

Researches were conducted for glasses in the systems BeO–Al₂O₃–B₂O₃ and MgO–Al₂O₃–B₂O. The following characteristics have been determined: thermal expansion coefficient within 20–300 °C, structural thermal expansion coefficient (STEC) and glass transition temperature. The discussed properties of Be-aluminoborate and Mg-aluminoborate glasses have been compared with those of Ca-, Sr- and Ba-aluminoborate glasses. TEC of studied glasses gets higher going from Be-aluminoborate glasses to Ba-aluminoborate ones, but T_g decreases under the same succession. The dependence of STEC on the nature of a given cation is more complicated. The pattern of dependence of the properties on composition is due to changing the boron coordination number with respect to oxygen, which is the main network-former, and to competition between the aluminium and boron for the oxygen brought by an ion-modifier. The difference between the effect of one ion-modifier and that of another is determined by decreasing the radius of an ion and increasing its electric field strength in the succession from Ba²⁺ to Be²⁺. The ions of Be and Mg can also act as network-former to some extent.     

Structural properties of Cr2O3–Fe2O3–P2O5 glasses,Part I

The structural properties of xCr₂O₃–(40 − x)Fe₂O₃–60P₂O₅, 0 ⩽ x ⩽ 10 (mol%) glasses have been investigated by Raman and Mössbauer spectroscopies, X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The Raman spectra show that the addition of up to 5.3 mol% Cr₂O₃ does not produce any changes in the glass structure, which consists predominantly of pyrophosphate, Q¹, units. This is in accordance with O/P ≈ 3.5 for these glasses. The increase in glass density and T_g that occurs with increasing Cr₂O₃ suggests the strengthening of glass network. The Mössbauer spectra indicate that the Fe²⁺/Fe_tot ratio increases from 0.13 to 0.28 with increasing Cr₂O₃ content up to 5.3 mol%, which can be related to an increase in the melting temperature from 1423 to 1473 K. After annealing, the 10Cr₂O₃–30Fe₂O₃–60P₂O₅ (mol%) sample was partially crystallized and contained crystalline β-CrPO₄ and Fe₃(P₂O₇)₂. The SEM and AFM micrographs of the partially crystallized sample revealed randomly distributed crystals embedded in a homogeneous glass matrix. EDS analysis indicated that the glass matrix was rich in Fe₂O₃ (39.6 mol%) and P₂O₅ (54.9 mol%), but contained only 5.5 mol% of Cr₂O₃. These results suggest that the maximum solubility of chromium in these iron phosphate melts is 5.5 mol% Cr₂O₃.     

BaTiO3-Nb2O5-Fe2O3陶瓷介电性能的研究

利用传统方法制备了BaTiO3-Nb2O5-Fe2O3(BTNF)陶瓷,采用X射线衍射仪、电容测试仪、电滞回线测量仪等测试手段研究了不同添加剂(Fe2O3、Co2O3、Nb2O5)对陶瓷晶体结构、介电性能及铁电性的影响.结果表明:Nb2O5是施主掺杂,易引起晶格畸变,使四方率增大;而Fe2O3为受主掺杂,其可提高氧空位浓度,促进BaTiO3陶瓷晶粒生长.同时掺杂Fe2O3、Nb2O5时,可以相互补偿.当Fe2O3浓度约为0.15;摩尔分数,Nb2O5浓度为0.79;摩尔分数时,陶瓷的介电常数达到4443,温度特性≤±10;,可以满足Y5P瓷料的要求.     

R2O-RO-SiO2-Al2O3-Fe2O3-P2O5系分相釉的研究

针对铁红分相釉的配方特点,采用L8(4 ×24)正交实验研究了钠长石、牛骨灰、滑石、方解石、石英加入量对R2O-RO-SiO2-Al2O3-Fe2O3-P2O5系统分相釉釉面效果的影响,采用扫描电子显微镜(SEM)和能谱分析(EDS)对釉层的微观结构进行了表征.研究发现:牛骨灰对釉面是否出现“柿红”效果影响最显著,而方解石影响最不明显.Si/P摩尔比对铁红色釉面的产生起关键作用,当Si/P摩尔比小于2O,出现铁红釉面效果的概率极高.随着滑石加入量从9份变化到18份,出现铁红色釉面的趋势反而降低.经SEM和EDS分析发现,“柿红色”、“酒红色”釉面效果的产生很大程度上是由于釉层液液分相促进Fe2O3富集或偏析造成,且特别容易在高钠、低镁、低铝处聚集,最终连成雪花状结晶.     

Semi-quantitative analysis for FTIR spectra of Al2O3-PbO-B2O3-SiO2 glasses

A series of glass of the molar formula xAl₂O₃-(50-x)PbO-25B₂O₃-25SiO₂ with x:2.5–17.5 with step of 2.5 mol.% was prepared and measured for, density, molar volume and infrared absorption. A semiquantitative analysis of the IR spectra was performed. It was found that each oxide would contribute in density with a specific factor. The density factor related to PbO is markedly higher than that of the other two oxides represent the glass skeleton which means that the content of PbO is the main factor affecting the density. The depolymerization of the whole glass skeleton increases with increasing the content of Al₂O₃. There is a competition between the role of PbO and Al₂O₃ in changing the value of N₄ and the crosslinking of the glass network. The silicate network tends to be distinguished from the reminder of the whole glass network with increasing alumina. The IR band located near 700 cm^? 1 was suggested to be due to the vibrations of bridging oxygens between trigonal boron atoms. An essential change in the role of PbO in these glasses from glass modifier to glass former occurred around 12 mol.% Al₂O₃.