Nano peel-off fabrication pattern with polymer overcoat layer on glassy carbon electrodes for Pt electrodeposition

This article describes a new technique for fabricating an electrocatalyst model in which the particle size and interparticle distance are controlled independently. We designed a uniform insulating polymer layer as a mask on an electroconductive glassy carbon substrate and then peeled off a part of the layer in nano-sized dots by scratching the overcoat layer using an atomic force microscope (AFM) cantilever. Pt particles electrodeposited only on the peeled off area of the glassy carbon. To peel-off a small area on the glassy carbon, a 29 ± 2 nm thick insulating polymer overcoat layer and a cantilever operating area of 10 nm × 10 nm were used, and the smallest peel-off area obtained was 30 nm × 30 nm. Thereafter, we performed the peel-off procedure on the polymer overcoat layer of the glassy carbon substrate having a cantilever operating area of 80 nm × 80 nm. Pt deposition of 100–150 nm in diameter was successfully achieved by adjusting the interparticle distance.     

Electrochemical, morphological and microstructural characterization of carbon film resistor electrodes for application in electrochemical sensors

The electrochemical and microstructural properties of carbon film electrodes made from carbon film electrical resistors of 1.5, 15, 140 Ω and 2.0 kΩ nominal resistance have been investigated before and after electrochemical pre-treatment at +0.9 V vs SCE, in order to assess the potential use of these carbon film electrodes as electrochemical sensors and as substrates for sensors and biosensors. The results obtained are compared with those at electrodes made from previously investigated 2 Ω carbon film resistors. Cyclic voltammetry was performed in acetate buffer and phosphate buffer saline electrolytes and the kinetic parameters of the model redox system Fe(CN)₆^3−/4− obtained. The 1.5 Ω resistor electrodes show the best properties for sensor development with wide potential windows, similar electrochemical behaviour to those of 2 Ω and close-to-reversible kinetic parameters after electrochemical pre-treatment. The 15 and 140 Ω resistor electrodes show wide potential windows although with slower kinetics, whereas the 2.0 kΩ resistor electrodes show poor cyclic voltammetric profiles even after pre-treatment. Electrochemical impedance spectroscopy related these findings to the interfacial properties of the electrodes. Microstructural and morphological studies were carried out using contact mode Atomic Force Microscopy (AFM), Confocal Raman spectroscopy and X-ray diffraction. AFM showed more homogeneity of the films with lower nominal resistances, related to better electrochemical characteristics. X-ray diffraction and Confocal Raman spectroscopy indicate the existence of a graphitic structure in the carbon films.     

Electrochemical characteristics of the dimercaptan-poly(ethylene oxide) grafted polyaniline electrodes

The electrochemical and transport properties of the 2,5-dimercapto-1,3,4-thiadiazole (DMcT)/poly(ethylene oxide) (PEO) grafted polyaniline electrodes and the DMcT/polyaniline electrode interfaced with the poly(acrylonitrile) (PAN) based solid-polymer-electrolyte (SPE) containing lithium perchlorate and ethylene carbonate were studied. Compared with the electrochemical and transport properties of the DMcT/polyaniline electrode, the capacitance and voltammetric current density, obtained by cyclic voltammetry, were increased for the electrode with low grafted polyaniline (less than 3 mol. %), while decreased when the applied copolymers were highly grafted ones. The charge transfer resistance obtained from impedance measurements was much smaller in the DMcT/PEO grafted polyaniline electrode than that in the DMcT/polyaniline electrode, and more pronounced reduction of charge transfer resistance was observed for the electrode with low grafted polyaniline. The diffusion coefficient of lithium cation in the electrode was increased when the PEO grafted polyaniline was used as an electrode material, however, the increase of the diffusion coefficient was less significant at higher graft degrees. All these changes in electrochemical and transport characteristics by the employment of PEO chains upon polyaniline backbones were attributed to the enhancement of lithium ion solvation and enlarged free volume in the electrode.     

Observing electrochemiluminescence behavior of quinoline in acetonitrile at a glassy carbon electrode

Electrochemiluminescence (ECL) behavior of quinoline in acetonitrile at a glassy carbon electrode was studied. Quinoline in 0.1 mol/L tetrabutylammonium bromide (TBAB) acetonitrile solution exhibited excellent ECL properties using conventional cyclic voltammetry (CV). One ECL peak was observed at −0.5 V. Effects of various factors were investigated. UV-visible absorption spectra measurements confirmed the production of new products after cycling the mixed solution. Fluorescence and ECL spectra measurements got the evidence that the luminophors were the products of quinoline. A possible mechanism process was proposed.     

Occurrence of particle debris field during focused Ga ion beam milling of glassy carbon

To explore the machining characteristics of glassy carbon by focused ion beam (FIB), particles induced by FIB milling on glassy carbon have been studied in the current work. Nano-sized particles in the range of tens of nanometers up to 400 nm can often be found around the area subject to FIB milling. Two ion beam scanning modes - slow single scan and fast repetitive scan - have been tested. Fewer particles are found in single patterns milled in fast repetitive scan mode. For a group of test patterns milled in a sequence, it was found that a greater number of particles were deposited around sites machined early in the sequence. In situ EDX analysis of the particles showed that they were composed of C and Ga. The formation of particles is related to the debris generated at the surrounding areas, the low melting point of gallium used as FIB ion source and the high contact angle of gallium on glassy carbon induces de-wetting of Ga and the subsequent formation of Ga particles. Ultrasonic cleaning can remove over 98% of visible particles. The surface roughness (R_a) of FIB milled areas after cleaning is less than 2 nm.     

Photoelectrochemical cells using metal-decorated carbon nanotube electrodes

We fabricated the photoelectrochemical (PEC) cells using n-type TiO₂ and metal (Pt, Pd)-decorated carbon nanotubes (CNTs) as an anode and a cathode, respectively. Photovoltaic effects were clearly observed. Compared with conventional PEC cell with Pt cathode, a larger photo-voltage was found in the PEC cells with the metal-decorated CNT cathode due to p-type semiconducting properties of CNTs. Additionally, we connected two PEC cells in series to decompose water into oxygen and hydrogen. Indeed, the connected PEC cells yielded the photo-voltage of about 1.35 V, which is larger than 1.23 V required for water splitting. This result demonstrates the possibility of hydrogen generation using the connected PEC cells without an external bias.     

离子液体凝胶聚合物电解质PP13TFSI-LiTFSI-P(VdF-HFP)的电化学性能 (cited: 1)

采用溶液浇铸法将N-甲基-N-丙基哌啶二(三氟甲基磺)亚胺(PP13TFSI)、二(三氟甲基磺)亚胺锂与偏氟乙烯-六氟丙烯共聚物(P(VdF-HFP))混合制备离子液体凝胶聚合物电解质(ILGPEs). 通过扫描电子显微镜观察发现,这种离子液体凝胶聚合物电解质由于液体相的均匀分布而具有疏松的结构. 采用电化学阻抗、计时电流法、线性扫描伏安法测试了电解质的离子电导率、锂离子迁移数和电化学窗口. 室温下离子液体凝胶聚合物电解质的离子电导率和锂离子迁移数分别是0.79 mS/cm和0.71,电化学窗口为0～5.1 Vvs. Li⁺/Li. 电池性能测试表明,这种离子液体凝胶聚合物电解质在Li/LiFePO₄电池中是稳定的,放电容量在30、75和150mA/g倍率下分别为135、117和100 mAh/g,电池经100个循环后容量保持在100%而几乎没有衰减.     

Removal of lead from aqueous solutions by using the natural and Fe(III)-modified zeolite

In the present study, the sorption of lead by the natural and Fe(III)-modified zeolite (clinoptilolite) is described. The characterization of the natural zeolite-rich rock and the Fe(III)-modified form was performed by chemical analysis, point of the zero charge (pH_pzc), X-ray powder diffraction, applying the Rietveld/RIR method for the quantitative phase analysis, and scanning electron microscopy. The effects of sorbents dose and the initial lead concentrations on its sorption by two sorbents were investigated. For both sorbents, it was determined that at lower initial concentrations of lead, ion exchange of inorganic cations in zeolites with lead, together with uptake of hydrogen dominated, while at higher initial lead concentrations beside these processes, chemisorption of lead occurred. Significantly higher sorption of lead was achieved with Fe(III)-modified zeolite. From sorption isotherms, maximum sorbed amounts of lead, under the applied experimental conditions, were 66 mg/g for the natural and 133 mg/g for Fe(III)-modified zeolite. The best fit of experimental data was achieved with the Freundlich model (R² ≥ 0.94).     

C60 sputtering of organics: A study using TOF-SIMS, XPS and nanoindentation

Sputtering of organic materials using a C₆₀ primary ion beam has been demonstrated to produce significantly less accumulated damage compared to sputtering with monatomic and atomic-cluster ion beams. However, much about the dynamics of C₆₀ sputtering remains to be understood. We introduce data regarding the dynamics of C₆₀ sputtering by evaluating TOF-SIMS depth profiles of bulk poly(methyl methacrylate) (PMMA). Bulk PMMA provides an ideal test matrix with which to probe C₆₀ sputter dynamics because there is a region of steady-state secondary ion yield followed by irreversible signal degradation. C₆₀ sputtering of PMMA is evaluated as a function of incident ion kinetic energy using 10 keV C₆₀⁺, 20 keV C₆₀⁺ and 40 keV C₆₀⁺⁺ primary ions. Changes in PMMA chemistry, carbon accumulation and graphitization, and topography as a function of total C₆₀ ion dose at each accelerating potential is addressed.     

Electrochemical synthesis of Ag nanoparticles supported on glassy carbon electrode by means of p-isopropyl calix[6]arene matrix and its application for electrocatalytic reduction of H2O2

The silver nanoparticles were prepared on the glassy carbon (GC) electrode, modified with p-iso propyl calix[6]arene, by preconcentration of silver ions in open circuit potential and followed by electrochemical reduction of silver ions. The stepwise fabrication process of Ag nanoparticles was characterized by scanning electron microscopy and electrochemical impedance spectroscopy. The prepared Ag nanoparticles were deposited with an average size of 70 nm and a homogeneous distribution on the surface of electrode. The observed results indicated that the presence of calixarene layer on the electrode surface can control the particle size and prevent the agglomeratione and electrochemical deposition is a promising technique for preparation of nanoparticles due to its easy-to-use procedure and low cost of implementation. Cyclic voltammetry experiments showed that Ag nanoparticles had a good catalytic ability for the reduction of hydrogen peroxide (H₂O₂). The effects of p-isopropyl calix[6]arene concentration, applied potential for reduction of Ag⁺, number of calixarene layers and pH value on the electrocatalytic ability of Ag nanoparticles were investigated. The present modified electrode exhibited a linear range from 5.0 × 10⁻⁵ to 6.5 × 10⁻³ M and a detection limit 2.7 × 10⁻⁵ M of H₂O₂ (S/N = 3) using amperometric method.     

Improvement of sound absorption characteristics under low frequency for micro-perforated panel absorbers using super-aligned carbon nanotube arrays

Super-aligned carbon nanotube (SACNT) arrays are grown on the surface of micro perforated panel (MPP) in the hope of improving the acoustic performance of MPP absorbers by virtue of their unique properties. Scanning electron microscopy reveals that SACNT arrays did not block the perforations of MPPs or changed the perforation diameter due to their “super-aligned” nature, although MPPs are thickened. The absorption effect of SACNT arrays which are of the same and different lengths with different incident side on MPP absorbers are investigated, and standing wave tube method is used to determine the normal sound absorption coefficient. Results show that both of the lengths of SACNT arrays and the incident side have effects on the sound absorption performance of MPP absorbers. And generally SACNT arrays help to improve the sound absorption capacity of MPP absorbers in low-frequency regions only when the SACNT arrays surface is the incident side. SACNT arrays decrease absorption performance of MPP absorbers when the MPP surface is used as the incident side. Moreover, SACNT arrays are found to increase the acoustic ability of MPP absorbers with the same structure parameters monotonically at lengths up to 600 μm in the condition that the SACNT arrays surface is used as the incident side.     

Optimization of nickel adsorption from aqueous solution by using activated carbon prepared from waste apricot by chemical activation

Waste apricot supplied by Malatya apricot plant (Turkey) was activated by using chemical activation method and K₂CO₃ was chosen for this purpose. Activation temperature was varied over the temperature range of 400-900 °C and N₂ atmosphere was used with 10 °C/min heat rate. The maximum surface area (1214 m²/g) and micropore volume (0.355 cm³/g) were obtained at 900 °C, but activated carbon was predominantly microporous at 700 °C. The resulting activated carbons were used for removal of Ni(II) ions from aqueous solution and adsorption properties have been investigated under various conditions such as pH, activation temperature, adsorbent dosage and nickel concentration. Adsorption parameters were determined by using Langmuir model. Optimal condition was determined as; pH 5, 0.7 g/10 ml adsorbent dosage, 10 mg/l Ni(II) concentration and 60 min contact time. The results indicate that the effective uptake of Ni(II) ions was obtained by activating the carbon at 900 °C.     

Characterisation of carbonaceous materials using Raman spectroscopy: a comparison of carbon nanotube filters,single‐ and multi‐walled nanotubes,graphitised porous carbon and graphite

Multi‐walled carbon nanotube (MWCNT) filters have been recently synthesised which have specific molecular filtering capabilities and good mechanical strength. Optical and scanning electron microscopy (SEM) reveals the formation of highly aligned arrays of bundles of carbon nanotubes having lengths up to 500 µm. The Raman spectra of this material along with four other carbonaceous materials, commercially available single‐walled carbon nanotubes (SWCNTs) and MWCNTs, graphitised porous carbon (Carbotrap) and graphite have been recorded using two‐excitation wavelengths, 532 and 785 nm, and analysed for band positions and shape with special emphasis paid to the D‐, G‐ and G′‐bands. A major difference between the different MWCNT varieties analysed is that G‐bands in the MWCNT filters exhibit almost no dispersion, whereas the other MWCNTs show a noticeable dispersive behaviour with a change in the excitation wavelength. Spectral features similar to those of the MWCNT filter varieties were observed for the Carbotrap material. From the line shape analysis, the intensity ratio, I_D/I_G, of the more ordered MWCNT filter material using the integral G‐band turns out to be two times lower than that of the less ordered MWCNT filter product at both excitation wavelengths. This parameter can, therefore, be used as a measure of the degree of MWCNT alignment in filter varieties, which is well supported also by our SEM study. Copyright © 2008 John Wiley & Sons, Ltd.