电场增强催化甲烷合成碳二烃催化剂影响研究

本研究提出了在常温、常压电场增强等离子体条件下甲烷直接转化合成碳二烃的洁净工艺 ,在不同的放电电压、放电功率、甲烷进料流量和不同的催化剂作用下 ,甲烷能够以不同的转化率和选择性转变为碳二烃。对影响甲烷转化率和碳二烃选择性的因素 :放电电压、放电功率、甲烷进料流量和催化剂进行了研究 ,对催化剂性能进行了比较 ,并探讨了反应机理。结果表明 ,适宜的工艺条件 :放电电压 2 0kV～ 4 0kV ;输入功率 :2 0W～ 4 0W ;合适的甲烷进料流量 :30mL/min～ 70mL/min。在该条件下 ,碳二烃的选择性可以达到 95 % ;催化剂对甲烷转化率的影响顺序为MnO2 /Al2 O3 >Ni/Al2 O3 >MoO3 /Al2 O3 >Ni/NaY >Pd/ZSM 5 >Ni/H4Mg2 Si3 O4>Ni/ZSM 5 >Co/ZSM 5 >无催化剂。     

Methane to Liquid Hydrocarbons over Tungsten-ZSM-5 and Tungsten Loaded Cu/ZSM-5 Catalysts

Metal containing ZSM-5 can produce higher hydrocarbons in methane oxidation. Many researchers have studied the applicability of HZSM-5 and modify ZSM-5 for methane conversion to liquid hydrocarbons, but their research results still lead to low conversion, low selectivity and low heat resistance. The modified HZSM-5, by loading with tungsten (W), could enhance its heat resistant performance, and the high reaction temperature (800℃) did not lead to a loss of the W component by sublimation. The loading of HZSM-5 with tungsten and copper (Cu) resulted in an increment in the methane conversion as well as CO2 and C5 selectivities. In contrast, CO, C2-3 and H2O selectivities were reduced. The process of converting methane to liquid hydrocarbons (C5 ) was dependent on the metal surface area and the acidity of the zeolite. High methane conversion and C5 selectivity, and low H2O selectivity are obtained over W/3.0Cu/HZSM.     

Optimization of methane conversion to liquid fuels over W-Cu/ZSM-5 catalysts by response surface methodology

The conversion of methane to liquid fuels is still in the development process. The modified HZSM-5 by loading with Tungsten （W） enhanced its heat resistant performance, and the high reaction temperature （800℃） did not lead to the loss of W component by sublimation. The loading of ZSM-5 with Tungsten and Copper （Cu） resulted in an increment in the methane conversion, CO2, and C5＋ selectivities. The high methane conversion and C5＋ selectivity, and low H2O selectivity are obtained by using W/3.0Cu/ZSM-5. The optimization of methane conversion over 3.0 W/3.0Cu/ZSM-5 under different temperature and oxygen concentration using response surface methodology （RSM） are studied. The optimum point for methane conversion is 19% when temperature is 753 ℃, and oxygen concentration is 12%. The highest C5＋ selectivity is 27% when temperature is 751 ℃. and oxwen concentration is 11%.     

Catalytic transformation of methane over in-loaded ZSM-5 zeolite in the presence of ethene

Methane is shown to react with ethene over In-loaded ZSM-5 to higher hydrocarbons such as propene and toluene at around 673 K. Such methane conversion is not catalyzed by proton-exchanged ZSM-5 (H-ZSM-5) under the same conditions, only C2H4 being converted to higher hydrocarbons. By using 13C-labeled methane (13CH4) as a reactant, the reaction paths for the formation of propene, benzene and toluene were examined. 13C-labeled propene (13CC2H6) is formed by the reaction of 13CH4 with C2H4. The lack of 13C-labeled benzene revealed that propene is not transformed to benzene, which instead originates entirely from C2H4. The 13C atom is inserted both into the methyl group and benzene ring in the toluene formed. This indicates that toluene is formed by two reaction paths; the reaction of 13CC2H6 with butenes formed by the dimerization of C2H4 and the reaction of benzene with 13CH4. The existence of the latter path was proved by the direct reaction of 13CH4 with benzene. The reaction of methane with benzene was also carried out in a continuous flow system over In-loaded ZSM-5. The reaction afforded 7.6% and 0.9% yields of toluene and xylenes, respectively, at 623 K.     

Conversion of Methane to C2 Hydrocarbons via Cold Plasma Reaction

Direct conversion of methane to C2 hydrocarbons via cold plasma reaction with catalysts has been studied at room temperature and atmospheric pressure. Methane can be converted into C2 hydrocarbons in different selectivity depending on the form of the reactor, power of plasma, flow rate of methane, ratio of N2/CH4 and nature of the catalysts. The selectivity to C2 hydrocarbons can reach as high as 98.64%, and the conversion of methane as high as 60% and the yield of C2 hydrocarbons as high as 50% are obtained. Coking can be minimized under the conditions of: proper selection of the catalysts, appropriate high flow rate of inlet methane and suitable ratio of N2 to CH4. The catalyst surface provides active sites for radical recombination.     

Characterization and Activity of Cr, Cu and Ga Modified ZSM—5 for Direct Conversion of Methane to Liquid Hydrocarbons

Direct conversion of methane using a metal-loaded ZSM-5 zeolite prepared via acidic ion exchange was investigated to elucidate the roles of metal and acidity in the formation of liquid hydrocarbons. ZSM-5 (SiO2/A12O3=30) was loaded with different metals (Cr, Cu and Ga) according to the acidic ion-exchange method to produce metal-loaded ZSM-5 zeolite catalysts. XRD, NMR, FT-IR and N2 adsorption analyses indicated that Cr and Ga species managed to occupy the alllmlnum positions in the ZSM-5 framework. In addition, Cr species were deposited in the pores of the structure. However, Cu oxides were deposited on the surface and in the mesopores of the ZSM-5 zeolite. An acidity study using TPD-NH3, FT-IR, and IR-pyridine analyses revealed that the total number of acid sites and the strengths of the BrSusted and Lewis acid sites were significantly different after the acidic ion exchange treatment.Cu loaded HZSM-5 is a potential catalyst for direct conversion of methane to liquid hydrocarbons. The successful production of gasoline via the direct conversion of methane depends on the amount of aluminum in the zeolite framework and the strength of the BrSnsted acid sites.     

Non-oxidative dehydro-oligomerization of methane to higher molecular weight hydrocarbons at low temperatures

The non-oxidative dehydro-oligomerization of methane to higher molecular weight hydrocarbons such as aroma tics and C2 hydrocarbons in a low temperature range of 773-973 K with Mo/HZSM-5,Mo-Zr/HZSM-5 and Mo-W/HZSM-5 catalysts is studied.The means for enhancing the activity and stability of the Mo-containing catalysts under the reaction conditions is reported.Quite a stable methane conversion rate of over 10% with a high selectivity to the higher hydrocarbons has been obtained at a temperature of 973 K.Pure methane conversions of about 5.2% and 2.0% have been obtained at 923 and 873 K,respectively.In addition,accompanied by the C2-C3 mixture,tht- methane reaction can be initiated even at a lower temperature and the conversion rate of methane is enhanced by the presence of tne initiator of C2-C3 hydrocarbons.Compared with methane oxidative coupling to ethylene,the novel way for methane transformation is significant and reasonable for its lower reaction temperatures and high selectivity to the desired prod     

Methane conversion into aromatic hydrocarbons over Ag-Mo/ZSM-5 catalysts

Nonoxidative methane conversion into aromatic hydrocarbons over ZSM-5-type high-silica zeolites modified with nanosized powders of molybdenum (4.0 wt %) and silver (0.1–0.5 wt %) is reported. The acidic properties of the catalysts have been investigated by temperature-programmed ammonia desorption. The microstructure and composition of the Ag-Mo/ZSM-5 catalytic systems have been studied by high-resolution transmission electron microscopy and energy-dispersive X-ray spectroscopy. The doping of the Mocontaining zeolite with silver enhances its activity and stability in nonoxidative methane conversion into aromatic hydrocarbons.     

Conversion of natural gas to C2 hydrocarbons via cold plasma technology

The plasma technology served as a tool in unconventional catalysis has been used in natural gas conversion, because the traditional catalytic methane oxidative coupling reaction must be performed at high temperature on account of the stability of methane molecule. The focus of this research is to develop a process of converting methane to C2 hydrocarbons with non-equilibrium plasma technology at room temperature and atmospheric pressure. It was found that methane conversion increased and the selectivity of C2 hydrocarbons decreased with the voltage. The optimum input voltage range was 40-80 V corresponding to high yield of C2 hydrocarbons. Methane conversion decreased and the selectivity of C2 hydrocarbons increased with the inlet flow rate of methane. The proper methane flow rate was 20-40 ml/min (corresponding residence time 10-20 s). The experimental results show that methane conversion was 47% and the selectivity of C2 hydrocarbons was 40% under the proper condition using atmospheric DBD cold plasma technology. It was found that the breakdown voltage of methane VB was determined by the type of electrode and the discharge gap width in this glow discharge reactor. The breakdown voltage of methane VB,min derived from the Paschen law equation was established.     

Conversion of natural gas to C_2 hydrocarbons via cold plasma technology

The plasma technology served as a tool in unconventional catalysis has been used in natural gas conversion,because the traditional catalytic methane oxidative coupling reaction must be performed at high temperature on account of the stability of methane molecule.The focus of this research is to develop a process of converting methane to C2 hydrocarbons with non-equilibrium plasma technology at room temperature and atmospheric pressure.It was found that methane conversion increased and the selectivity of C2 hydrocarbons decreased with the voltage.The optimum input voltage range was 40-80 V corresponding to high yield of C2 hydrocarbons.Methane conversion decreased and the selectivity of C2 hydrocarbons increased with the inlet flow rate of methane.The proper methane flow rate was 20-40 ml/min (corresponding residence time 10-20 s).The experimental results show that methane conversion was 47% and the selectivity of C2 hydrocarbons was 40% under the proper condition using atmospheric DBD cold plasma technology.It was found that the breakdown voltage of methane VB was determined by the type of electrode and the discharge gap width in this glow discharge reactor.The breakdown voltage of methane VB,min derived from the Paschen law equation was established.     

Catalytic Combustion of Methane over High Copper-Loading ZSM-5 Catalysts

Two series of Cu/ZSM-5 catalysts,loading from 5 to 20 wt% CuO,were prepared by the deposition-precipitation and impregnation methods,respectively.The catalysts prepared by the impreg- nation method showed better catalytic performances than those prepared by the deposition-precipitation method and the increase of copper loading favored methane conversion.20Cu(I)/ZSM-5 had the highest activity with T_(90%)of 746 K,and for 20Cu(D)/ZSM-5,T_(90%)was as high as 804 K.The characteriza- tion of X-ray diffraction(XRD),temperature-programmed reduction(TPR),temperature-programmed desorption(TPD),and X-ray photoelectron spectroscopy(XPS)revealed that the dispersion of cop- per species could be improved by using the deposition-precipitation method instead of the impregnation method,but the fraction of surface CuO,corresponding to active sites for methane oxidation,was larger on 20Cu(I)/ZSM-5 than 20Cu(D)/ZSM-5.The results of Pyridine-Fourier transform infrared spectrum (Py-FT-IR)showed that a majority of Lewis acidity and a minority of Brφnsted acidity were present on Cu/ZSM-5 catalysts.20Cu(I)/ZSM-5 presented more Lewis acid sites.The number of Lewis acid sites changed significantly with preadsorption of oxygen.Adsorption of methane and oxygen on acid sites was observed.The properties of Cu/ZSM-5 catalysts were correlated with the activity for methane oxidation.     

ZSM-5／MOR复合分子筛催化剂对混合C4烃转化反应的催化性能

以ZSM-5/丝光沸石(MOR)复合分子筛为催化剂,对混合C4烃的催化转化反应进行了评价,并采用程序升温脱附和原位红外光谱技术对ZSM-5/MOR的酸性进行了表征. 结果表明,与ZSM-5相比, MOR具有很低的催化活性,但ZSM-5/MOR复合分子筛具有较高的催化活性,随着ZSM-5/MOR复合分子筛中ZSM-5含量的增加, C4烃转化率稍有升高;在C4烃转化率大致相同的情况下,乙烯和丙烯的总选择性比较接近,但苯和甲苯的总收率却快速升高. 随着ZSM-5/MOR复合分子筛中ZSM-5含量的增加,弱酸和中强酸的酸量逐渐减少,强酸的酸量有所增加. 由于ZSM-5/MOR复合分子筛中MOR对ZSM-5起到分散作用而产生更多的L酸中心,且此L酸中心处于分子筛的外表面而具有较高的能量,导致苯和甲苯的总收率升高.     

Preparation method effect on the physicochemical and catalytic properties of a methane dehydroaromatization catalyst

The molybdenum precursor effect on the physicochemical properties of the Мо/ZSM-5 catalyst and on its catalytic properties in nonoxidative methane conversion into aromatic hydrocarbons has been investigated. The textural characteristics of molybdenum catalysts have been determined by low-temperature nitrogen adsorption, and their acidity has been measured by temperature-programmed ammonia desorption. The microstructure and composition of Mo/ZSM-5 samples have been determined by high-resolution transmission electron microscopy and energy-dispersive X-ray spectroscopy. The activity and on-stream stability of the Мо-containing zeolite catalyst in the nonoxidative conversion of methane depend on the type of molybdenum compound that was used in catalyst preparation.     

甲烷二氧化碳介质阻挡放电转化产物分布研究

针对介质阻挡放电甲烷二氧化碳转化实验,分析了反应的产物分布,探讨了进料组成和反应器结构对反应的影响.反应产物包括:高H2/CO摩尔比的合成气、气态烃、高辛烷值的汽油组分、醇和酸等含氧有机物.对所述电极结构,产物的选择性随碳数增加而降低;高的甲烷进料浓度有利于烃的生成,对醇和酸的最佳甲烷进料体积分数范围在67.4％～75.1％;放电间隙越小,原料转化率和烃、酸的选择性越大,大的放电间隙对醇的生成有利.     

无胺合成[Fe]ZSM-5分子筛的结构鉴定及其催化性能的研究

不用有机胺为模板剂,在碱性介质中采用水热合成法成功地合成了[Fe]ZSM-5分子筛.用X射线衍射、透射电镜、红外光谱、顺磁共振谱、X射线光电子能谱和穆斯堡尔谱等对其结构进行了表征,结果表明,Fe原子进入了分子筛骨架,并处于四面体的配位环境.在由甲醇转化为汽油的过程中,以本文合成的[Fe]ZSM-5与用有机胺为模板剂合成的[Fe]ZSM-5分子筛为催化剂相比,其活性和选择性几乎相同,且都比通常的H[Al]ZSM-5好,C₅组分以上的选择性大于80%,且芳烃(包括脂环烃)和异构烃的含量达75%以上.     

Nonoxidative methane conversion into aromatic hydrocarbons on tungsten-containing pentasils

The effects of the tungsten concentration and of the method of tungsten introduction into ZSM-5 pentails with different SiO₂/Al₂O₃ molar ratios on the acidity and the activity of the resulting catalysis in nonoxidative methane conversion into aromatic hydrocarbons are considered. The catalysts obtained from the SiO₂/Al₂O₃ = 40 pentasil and a nanosized tungsten powder are the most active and the most stable. The maximum methane conversion and the highest yield of aromatic hydrocarbons are achieved on the zeolite containing 8.0 wt % tungsten nanopowder.     

Conversion of natural gas to C_2 hydrocarbons through dielectric-barrier discharge plasma catalysis

The experiments are carried out in the system of continuous flow reactors with dielectric-barrier discharge (DBD) for studies on the conversion of natural gas to C2 hydrocarbons through plasma catalysis under the atmosphere pressure and room temperature. The influence of discharge frequency, structure of electrode, discharge voltage, number of electrode, ratio of H2/CH4, flow rate and catalyst on conversion of methane and selectivity of C2 hydrocarbons are investigated. At the same time, the reaction process is investigated. Higher conversion of methane and selectivity of C2 hydrocarbons are achieved and deposited carbons are eliminated by proper choice of parameters. The appropriate operation parameters in dielectric-barrier discharge plasma field are that the supply voltage is 20-40 kV (8.4-40 W), the frequency of power supply is 20 kHz, the structure of (b) electrode is suitable, and the flow of methane is 20-60 ml · min-1. The conversion of methane can reach 45%, the selectivity of C2 hydrocarbons i     

无第二模板剂法合成多级结构ZSM-5分子筛微球及其在甲烷无氧芳构化反应中的应用

在无第二模板剂的条件下,采用简单的水热晶化法,通过控制条件合成出具有多级结构的ZSM-5(ZSM-5-HW)分子筛,并运用X射线衍射、红外光谱、扫描电镜和N2吸附-脱附等技术对合成的分子筛进行了表征.结果表明,所得样品是由棒状晶体组装而成的具有介孔结构的分子筛微球.用等体积浸渍法制备了Mo/HZSM-5-HW催化剂并用于CH4无氧芳构化反应,表现出较高的催化活性和稳定性.在实验条件下,CH4初始转化率为18.5%,而苯收率最高可达9.5%;反应24h后,两者仍然分别保持在10.2%和5.5%左右.     

Effect of La2O3／γ—Al2O3 Catalyst on the Activation of CH4 and CO2 to C2 Hydrocarbons under Non—equilibrium Plasma

In the reaction of methane and carbon dioxide to C2 hydrocabons under non-equilibrium plasma, methane conversion was decreased,but selectivity of C2 hydroxarbons was increased when using La2O3/γ-Al2O3 as catalyst. So the yield of C2 hydrocarbons was higher than using plasma alone. The synergism of La2O3/γ-Al2O3 and plasma gave methane conversion of 24.9% and C2 yield of 18.1%. The distribution of C2 hydrocarbons changed when Pd-La2O3/γ-Al2O3 was used as catalyst,the major C2 product was ethylene.     

Effect of La_2O_3/γAl_2O_3 Catalyst on the Activation of CH_4 and CO_2 to C_02 Hydrocarbons under Non-equilibrium Plasma

The oxidative coupling of methane (OCM) to C2 hydrocarbons using carbon dioxide as oxidant is an attractive process from environmental point of view. Only a few research papers reported for it1-3. In general, the yield of C2 hydrocarbons was about 6%. This indicated that the method of catalytic activation was unfavorable to the reaction. It is necessary for us to find a new method in order to activate reaction and improve C2 hydrocarbon yield. Non-equilibrium plasma is a cold plasma in…