Molecular interconversion behaviour in comprehensive two-dimensional gas chromatography

Comprehensive two-dimensional gas chromatography (GC x GC) is shown to provide information on dynamic molecular behaviour (interconversion), with the interconversion process occurring on both columns in the coupled-column experiment. The experiment requires suitable adjustment of both experimental conditions and relative dimensions of each of the columns. In this case, a longer column than normally employed in GC x GC allows sufficient retention duration on the second column, which permits the typical plateau-shape recognised for the interconversion process to be observed. The extent of interconversion depends on prevailing temperature, retention time, and the phase type. Polyethylene glycol-based phases were found to result in high interconversion kinetics, although terephthalic acid-terminated polyethylene glycol had a lesser extent of interconversion. Much less interconversion was seen for phenyl-methylpolysiloxane and cyclodextrin phases. This suggests that for the oximes, interconversion largely occurs in the stationary phase. Examples of different extents of interconversion in both dimensions are shown, including peak coalescence on the first column with little interconversion on the second column.     

Model for predicting comprehensive two-dimensional gas chromatography retention times

A model for approximating the relative retention of solutes in comprehensive two-dimensional gas chromatography (GCxGC) is presented. The model uses retention data from standard single-column temperature-programmed separations. The one-dimensional retention times are first converted into retention indices and then these indices are combined in a simple manner to generate a retention diagram. A retention diagram is an approximation of the two-dimensional chromatogram that has retention order and spacing in both dimensions similar to that found in the experimental chromatogram. If required, the retention diagram can be scaled to more closely resemble the two-dimensional chromatogram. The model has been tested by using retention time data from single-column gas chromatography-mass spectrometry and valve-based GCxGC. A total of 139 volatile organic compounds (VOCs) were examined. Approximately half of the VOCs had a single functional group and a linear alkyl chain (i.e., compounds with the structure Z-(CH(2))(n)-H). The retention diagrams had primary retention orders that were in excellent agreement with the GCxGC chromatograms. The relative secondary retention order for compounds with similar structures was also accurately predicted by the retention diagram. However, the relative secondary retention for compounds with dissimilar structures, such as acyclic alcohols and multi-substituted alkylbenzenes, were less accurately modeled. This study demonstrates how readily available single-column retention time data can be used to provide an a priori estimate of the relative retention of solutes in a GCxGC chromatogram. Such a capability is useful for screening possible combinations of stationary phases.     

Evaluation of a retention model in comprehensive two-dimensional gas chromatography

Modeling the retention in comprehensive two-dimensional gas chromatography (GC x GC) was achieved using retention indices obtained in conventional GC. Predicted results were compared with experimental data obtained in the two-dimensional separation of a synthetic hydrocarbon mixture. This proved to be helpful in optimizing the operating conditions of GC x GC separation of a complex petroleum sample and in identifying chemical families.     

Effects of pressure drop on absolute retention matching in comprehensive two-dimensional gas chromatography

Comprehensive two-dimensional gas chromatography (GC x GC) analysis has the capability to resolve many more components of complex mixtures than traditional single column GC analysis. There is an increasing need to provide reliable identification of these separated components; time-of-flight mass spectrometry (TOFMS) is the most appropriate technology to achieve this task. Rather than require MS for all GC x GC separations, it is desirable to assign peak identities to specific peak positions in the GC x GC separation space, and this necessitates matching peak retentions in the two experiments - GC x GC-FID and GC x GC-TOFMS. The atmospheric vs. vacuum outlet conditions confound this task. It is shown here that by employing a supplementary gas supply, provided to a T-union between the column outlet and the MS interface, it is possible to generate 2D chromatograms for GC x GC-FID and GC x GC-TOFMS that are essentially exactly matched. There is no degradation in separation performance or efficiency in the second column in the system interfaced to the T-union. Since the GC x GC-FID experiment uses hydrogen for maximum efficiency, and GC x GC-TOFMS uses helium carrier, translation of (conditions/retentions) must account for the different viscosities of the carrier gases. Translation of conditions is based on well-known principles established in single column analysis. Tabulated data illustrate that retention reproducibility was of the order of better than 4 s for the average first dimension retention difference, and about 40 ms for the average second dimension retention difference when comparing GC x GC-FID and GC x GC-TOFMS results. This should provide considerable support for identification in routine GC x GC-FID analysis of specific sample types, once the peaks in 2D separation space have been assigned identities through GC x GC-TOFMS analysis.     

Retention indices in comprehensive two-dimensional gas chromatography

The identification of compounds by using gas chromatography (GC) in samples with significant complexity comprising a range of isomeric species, where characterization is based on peak retention times and mass spectra, generates uncertainty for the analyst. This leads to identification errors. The most reliable way to confirm the identification of each compound is based on authentic standard co-injection, which in several cases is economically prohibitive, and often unachievable in the time available for analysis. Retention index procedures are important tools to minimize misidentification of compounds in conventional chromatography. The introduction of comprehensive two-dimensional GC (GC × GC) for analysis of complex samples was a decisive step to increase the analytical capacity of chromatographic techniques. For many samples, the chromatographic resolution increase leads to quantitative expansion in the number of peaks identified, compared with conventional GC analysis. Notwithstanding this improved resolution, limitations still persist in correct peak identification, which suggests the use of retention indices may assist in supporting component identification in this important technique. In this work, approaches to use of the retention index in GC × GC are discussed, based on an evaluation of the literature in this area. Interpretation of effective chain length data for fatty acid methyl esters in the first and second dimensions is presented.     

Measurement of retention in comprehensive two-dimensional gas chromatography using flow modulation with methane dopant

Flow modulation of methane-doped carrier gas is used to visualize the second dimension hold-up time in GC × GC continuously throughout the run. This provides an internal reference of hold-up time and presents a straightforward means of examining retention in each dimension of GC × GC. Retention factors on similar and dissimilar column pairs are examined. Stationary phase bleed is shown to be retained by the second dimension column.     

Pulsed flow modulation comprehensive two-dimensional gas chromatography

Pulsed flow modulation (PFM) is based on higher flow rate time compression of the first GC column effluent, which prior to the injection into the second column is stored for a few seconds in a standard fused silica wide bore transfer line. We constructed the PFM device with two standard 1/16 in. brass compression fittings with the insertion of the two columns inside the wide bore 0.53 mm i.d. fused silica storage transfer line for the elimination of dead volumes. This simple arrangement provides a combination of flexibility in the length of the sample storage transfer line hence comprehensive two-dimensional gas chromatography (GC x GC) cycle time, inert sample path and full elimination of cooling gas consumption. A record short second column injection time of 20 ms is demonstrated. Practical injection times are the sample collection time (such as 4s) divided by the second to first column flow rate ratio (such as 20/0.7), which is typically around 150 ms. Due to the low cost of the device it can also be considered for use with non comprehensive time segmented GC x GC to remove a few accidental coelutions. PFM-GCxGC excels with high second column capacity due to the use of 0.32 mm i.d. columns with high flow rates as the second dimension GC x GC column. As a result, PFM-GCxGC can have up to two orders of magnitude higher second column sample capacity and linear dynamic range for improved reduction of adverse matrix interference effects due to column overloading.     

Detector technologies for comprehensive two-dimensional gas chromatography

The detector is an integral and important part of any chromatographic system. The chromatographic peak profiles (i.e. peak separation) should, ideally, be unaffected by the detector--it should only provide the sensing capacity required at the end of a column separation process. The relatively new technique of comprehensive 2-D GC (GC x GC) extends the performance of GC manyfold, but comes at a price--existing GC systems may not be adequately designed with the requirements of GC x GC in mind. This is primarily the need for precise measurement of very fast peaks entering the detector (e.g. as fast as 50 ms basewidth in some instances). The capacity of the detector to closely track a rapidly changing chromatographic peak profile depends on a number of factors, such as design of flow paths and make-up gas introduction, type of detector response mechanism, and the chemistry of the response. These factors are discussed here as a means to appreciate the technical demands of detection in GC x GC. The MS detector will not be included in this review.     

Flow-switching device for comprehensive two-dimensional gas chromatography

A simple flow-switching device has been developed as a differential flow modulator for comprehensive two-dimensional gas chromatography (GC x GC). The device is assembled from tubing, four tee unions, and a solenoid valve. The solenoid valve is located outside the oven of the gas chromatograph and is not in the sample path. The modulation technique has no inherent temperature restrictions and passes 100% of the primary column effluent to the secondary column(s). Secondary peaks are produced with widths at half maximum less than 100 ms when operating in GC x 2GC mode with a 2.0 s modulation period. The efficacy of this approach is demonstrated through the analysis of a standard mixture of volatile organic compounds (VOCs) and diesel fuel.     

Comparative visualization for comprehensive two-dimensional gas chromatography

This paper investigates methods for comparing datasets produced by comprehensive two-dimensional gas chromatography (GC x GC). Chemical comparisons are useful for process monitoring, sample classification or identification, correlative determinations, and other important tasks. GC x GC is a powerful new technology for chemical analysis, but methods for comparative visualization must address challenges posed by GC x GC data: inconsistency and complexity. The approach extends conventional techniques for image comparison by utilizing specific characteristics of GC x GC data and developing new methods for comparative visualization and analysis. The paper describes techniques that register (or align) GC x GC datasets to remove retention-time variations; normalize intensities to remove sample amount variations; compute differences in local regions to remove slight misregistrations and differences in peak shapes; employ color (hue), intensity, and saturation to simultaneously visualize differences and values; and use tools for masking, three-dimensional visualization, and tabular presentation with controls for graphical highlights to significantly improve comparative analysis of GC x GC datasets. Experimental results indicate that the comparative methods preserve chemical information and support qualitative and quantitative analyses.     

Image background removal in comprehensive two-dimensional gas chromatography

This paper describes a new technique for removing the background level from digital images produced in comprehensive two-dimensional gas chromatography (GCxGC). Background removal is an important first step in the larger problem of quantitative analysis. The approach estimates the background level across the chromatographic image based on structural and statistical properties of GCxGC data. Then, the background level is subtracted from the image, producing a chromatogram in which the peaks rise above a near-zero mean background. After the background level is removed, further analysis is required to determine the quantitative relationship between the peaks and chemicals in the sample. The algorithm is demonstrated experimentally to be effective at determining and removing the background level from GCxGC images. The algorithm has several parametric controls and is incorporated into an interactive program with graphical interface for rapid and accurate detection of GCxGC peaks.     

Identification of unknown compounds on the basis of retention index data in comprehensive two-dimensional gas chromatography

The identification of unknown compounds in complex samples is very difficult. Comprehensive two-dimensional gas chromatography (GC x GC) provides very good resolution and improved identification reliability. Mass spectrometry is a powerful identification tool and retention index data are another good approach to this end. In this study, a second-order polynomial was used to calculate retention index data based on n-alkanes beyond the region of the 'isovolatile' curve in GC x GC, and the results in the 2nd dimension were validated by using the same stationary phase column in one-dimensional GC. To test the usefulness of the method, volatile compounds in a tobacco leaf extract fraction were analyzed using GC x GC, and 60 compounds were identified on the basis of their retention indices.     

Semi-rotating cryogenic modulator for comprehensive two-dimensional gas chromatography

A laboratory-made cryogenic modulator for comprehensive two-dimensional gas chromatography (GCxGC) was constructed and evaluated. Analytes were trapped with carbon dioxide and desorbed with heated GC oven air. The GCxGC system included a non-polar first-dimension column and a semi-polar second-dimension column connected to a flame ionisation detector. A laboratory-written Matlab-based program was used for the data analysis. Peak widths at half height for n-alkanes, obtained with use of new modulator, were at narrowest 60 ms.     

Stop-flow comprehensive two-dimensional gas chromatography with pneumatic switching

A new method for performing comprehensive GC x GC in the stop-flow mode is presented. A device was used to pneumatically stop the flow in the first dimension ((1)D) (by applying pressure pulses at the junction between the two columns), while flow was maintained in the second dimension ((2)D). This allowed for better preservation of resolution in the (1)D of the GC x GC chromatograms, and the extension of the (2)D's separation space, reducing or eliminating the extent of wraparound. When increased flow rates in the (2)D were used, sensitivity enhancements were also observed.     

Simple calibration procedure for comprehensive two-dimensional gas chromatography

Mass transfer from the first-dimension to the second-dimension column in comprehensive two-dimensional gas chromatography (GC x GC) is normally quantitative, which means that the peak areas produced by GC x GC are equal to those obtained in one-dimensional gas chromatography (GC). In view of this relationship, it was investigated whether normal GC calibration could be used to quantify compounds analysed by GC x GC. Quantification of polycyclic aromatic hydrocarbons (PAHs) in sediment was used as a test case. It was concluded that more laborious and time-consuming GC x GC area calibration can be replaced by GC area calibration if separation quality and quantity prerequisites are met.     

Principles and applications of comprehensive two-dimensional gas chromatography

This issue of Trends in Analytical Chemistry celebrates 50 years of gas chromatography (GC) — the greatest enabling technology for chemical analysis of volatile compounds. However, what may be considered the most powerful separation tool in GC — comprehensive two-dimensional gas chromatography (GC×GC) — is a development born of the 1990s. It was first described and almost fully established in the last decade of the twentieth century. The coming decades can be expected to see it flourish into a major operating mode of GC, when applications and fundamental principles will be further expanded, and, most importantly, its universal acceptance will be unquestioned. This article describes why the pioneers of GC×GC have so much faith in the new opportunities afforded by this exciting technology.     

A method of calculating the second dimension retention index in comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry

A method was developed to calculate the second dimension retention index of comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC/TOF-MS) data using n-alkanes as reference compounds. The retention times of the C(7)-C(31) alkanes acquired during 24 isothermal experiments cover the 0-6s retention time area in the second dimension retention time space, which makes it possible to calculate the retention indices of target compounds from the corresponding retention time values without the extension of the retention space of the reference compounds. An empirical function was proposed to show the relationship among the second dimension retention time, the temperature of the second dimension column, and the carbon number of the n-alkanes. The proposed function is able to extend the second dimension retention time beyond the reference n-alkanes by increasing the carbon number. The extension of carbon numbers in reference n-alkanes up to two more carbon atoms introduces <10 retention index units (iu) of deviation. The effectiveness of using the proposed method was demonstrated by analyzing a mixture of compound standards in temperature programmed experiments using 6 different initial column temperatures. The standard deviation of the calculated retention index values of the compound standards fluctuated from 1 to 12 iu with a mean standard deviation of 5 iu.     

Recent developments in the application of comprehensive two-dimensional gas chromatography

The literature on comprehensive two-dimensional gas chromatography (GC x GC) is reviewed, with emphasis on application-oriented studies published in the period 2004-2006. The various strategies that can be used in such studies, the state-of-the-art analytical performance and the high potential of GC x GC combined with time-of-flight mass spectrometric detection are highlighted.