Acoustic emission and thermal expansion of Pb(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript> and Pb(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript>-PbTiO<Subscript>3</Subscript> crystals

The temperature dependence of the elongation per unit length for Pb(Mg_1/3Nb_2/3)O₃ crystals unannealed after growth and mechanical treatment is investigated in the course of thermocycling. It is revealed that this dependence deviates from linear behavior at temperatures below 350°C. The observed deviation is characteristic of relaxors, is very small in the first cycle, increases with increasing number n of thermocycles, and reaches saturation at n≥3. In the first cycle, a narrow maximum of the acoustic emission activity is observed in the vicinity of 350°C. In the course of thermocycling, the intensity of this maximum decreases and becomes zero at n>3. For (1?x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ crystals, the dependence of the temperature of this acoustic emission maximum on x exhibits a minimum. It is assumed that the phenomena observed are associated with the phase strain hardening due to local phase transitions occurring in compositionally ordered and polar nanoregions.     

The role of the secondary pyroelectric effect in a ferroelectric relaxor 0.72Pb(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript>-0.28PbTiO<Subscript>3</Subscript>

The depth profile of the pyroelectric coefficient effective values of a 0.72Pb(Mg_1/3Nb_2/3)O₃-0.28PbTiO₃ (PMN-0.28PT) single crystal is studied. It was shown that owing to high pyroelectric coefficients the secondary pyroelectric effect significally contributes (∼40%) to the total pyroelectric coefficient.     

Dielectric dispersion and magnetic properties of Ba-modified Pb(Fe<Subscript>1/2</Subscript>Nb<Subscript>1/2</Subscript>)O<Subscript>3</Subscript>

The polycrystalline samples of Ba-modified Pb(Fe_1/2Nb_1/2)O₃ (i.e., (Pb_1-xBa_x)(Fe_1/2Nb_1/2)O₃ PBFN, with x=0,0.05,0.07) were synthesized by a mechanosynthesis (i.e., high-energy ball milling) route followed by a mixed oxide method. Structural analysis provides the information on formation of single-phase orthorhombic structure on substitution of a small amount (x=0.07) of Ba at the Pb-site of Pb(Fe_0.50Nb_0.50)O₃ (PFN). The ferroelectric–paraelectric phase transition in PFN was observed at 383 K, which decreases on increasing Ba-concentration in PBFN. Detailed studies of dielectric properties of PBFW show the following: (i) diffuse phase transition, (ii) low loss tangent, (iii) low activation energy, and (iv) low frequency dielectric dispersion. An anomaly in the ac conductivity was found very close to phase transition temperature. The activation energy is found to decrease from 0.19 to 0.01 eV on increasing Ba-concentration to 7% (x=0.07). Temperature field-dependent magnetization measurements of all the samples showed antiferromagnetic transition at ∼15 K (for x=0.07). PBFN sample showed a slight increase in the coercivity (i.e., from 400 Oe (PFN) to 500 Oe (PBFN, for x=0.07) at 2 K. PACS 61.10.Nz; 68.37.Hk; 75.50.Ss; 75.60.Ej; 77.22.Ch; 77.22.Gm     

Polar nanoregions in Pb(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript> (PMN): insights from a supercell approach

We report construction of a model of polar nanoregions in the PMN relaxor ferroelectric based on first-principles lattice dynamics for chemically ordered supercells [S.A. Prosandeev et al., Phys. Rev. B 70, 134110 (2004)], combined with invariance under permutations and dipole-dipole interaction as a source supporting randomly oriented residual polarization. Representative analytical estimates of polar nanore-gion — supercell mapping reproduce both nonzero local and zero macroscopic polarization of the structure, as well as the temperature change of the supercell anisotropy at cooling and field cooling.     

Dielectric and polar order behaviors of BaTiO<Subscript>3</Subscript>-Bi(Mg<Subscript>1/2</Subscript>Ti<Subscript>1/2</Subscript>)O<Subscript>3</Subscript> ceramics

New perovskite solid solution ceramics of (1−x)BaTiO₃-xBi(Mg_1/2Ti_1/2)O₃ ((1−x)BT-xBMT, x≤0.09) were synthesized by the solid-state reaction technique. X-ray diffraction studies have revealed a stable single perovskite structure for all samples. Dielectric measurements were carried out at different frequencies and temperatures. The polarization evolutions with temperatures were measured to investigate the ferroelectric properties. All the compositions show features of ferroelectrics with diffuse phase transition, though the temperature T _m of their dielectric constant maximum ε _m is frequency dependent. The dielectric constant peak ε(T) of (1−x)BT-xBMT ceramics become broad with increasing BMT content. During the temperature range of ε(T) peak summit, (1−x)BT-xBMT ceramics present quasi-linear dielectric phenomenon under high electric field with very high dielectric constant.     

Heterophase states in 0.10PbTiO<Subscript>3</Subscript>-0.90Pb(Zn<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript> crystals

A new model of the elastic matching of phases is proposed, and heterophase structures near the morphotropic phase boundary in 0.10PbTiO₃-0.90Pb(Zn_1/3Nb_2/3)O₃ crystals are studied. Unique behavior of the unit cell parameters is found to favor the elastic matching of the ferroelectric tetragonal and orthorhombic phases under the conditions of complete or partial relaxation of internal mechanical stresses at a volume concentration ratio of these phases of about 20/80% and temperatures of T=20–300 K. Interrelations between the volume concentrations of different domain (twin) types and of the coexisting phases are analyzed.     

Structural and electrical properties of 0.7Pb(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript>–0.3PbTiO<Subscript>3</Subscript> thin films grown on Ir/MgO buffered Si(100) substrates

Thin films of 0.7Pb(Mg_1/3Nb_2/3)O₃–0.3PbTiO₃ (PMN-PT) have been grown on Ir/MgO buffered Si(100) substrates at different substrate temperatures by pulsed laser deposition. Crystalline phases as well as preferred orientations in the PMN-PT films were investigated by X-ray diffraction analysis (XRD). The microstructure, dielectric and ferroelectric properties of PMN-PT film prepared at 650 °C were studied. The results show that the film prepared at 650 °C exhibits pure perovskite phase and single c-axis orientation. The dielectric constant and dissipation factor of the single c-axis oriented film are 1000 and 0.04 at a frequency of 1 kHz, while the remnant polarization and coercive field are about 13.0 μC/cm² and 100 kV/cm under an electric field of 480 kV/cm, respectively. PACS 81.15.Fg; 77.80.-e; 77. 22.Ej; 77.55.+f; 85.50.Gk     

Effect of Ba-substitution on the structure and properties of Pb<Subscript>0.8</Subscript>Ba<Subscript>0.2</Subscript>[(In<Subscript>1/2</Subscript>Nb<Subscript>1/2</Subscript>)<Subscript>1-x</Subscript>Ti<Subscript>x</Subscript>]O<Subscript>3</Subscript> ceramics

Ferroelectric ceramics with formula Pb_0.8Ba_0.2[(In_1/2Nb_1/2)_1-xTi_x]O₃ (PBINT) (x=0.0,0.1,0.2,0.3,0.4 and 0.5) were prepared via a two-step solid state reaction method. It was found that ceramics with compositions in the range of x=0.0∼0.3 showed a pseudo-cubic structure, whereas the ceramic with x=0.5 displayed a tetragonal structure. All compositions showed significant frequency dispersion in their dielectric properties. The remanent polarization P_r as well as the coercive field E_c, measured at room temperature, increases with the Ti content. The experimental results obtained in this system are summarized into a phase diagram, with the morphotropic phase boundary (MPB) located at x=0.4. Compared with the Pb[(In_1/2Nb_1/2)_1-xTi_x]O₃ solid solution system, incorporating Ba in the A-site leads to a significant decrease in the dielectric maximum temperature T_max, a suppression of the dielectric relaxation parameter γ, and a shift of the MPB composition to a higher Ti content. PACS 77.84.Dy; 77.80.Bh; 77.22.Ch     

Electro-optical polarization mode dispersion in PbMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript> single crystals

The polarization mode dispersion induced by an external ac electric field in PbMg_1/3Nb_2/3O₃ single crystals is studied experimentally at frequencies of 10⁴–10⁷ Hz. It is established that the discovered electro-optical polarization mode dispersion (EPMD) displays anomalous properties related to the orientation of the induced dipole moments in microregions of the crystal. Analytical expressions describing the peculiarities of the physical properties of relaxors giving rise to the EPMD are obtained.     

Dielectric investigations in Sr<Subscript>0.75</Subscript>Ba<Subscript>0.25</Subscript>Nb<Subscript>2</Subscript>O<Subscript>6</Subscript> relaxor ferroelectric thin films

The dielectric properties of Sr_0.75Ba_0.25Nb₂O₆ relaxor ferroelectric thin films were carefully analyzed. In contrast to bulk samples which present three distinct dielectric relaxation phenomena Sr_0.75Ba_0.25Nb₂O₆ thin films present only two of them. The suppression of the third anomaly can be mainly attributed to the narrow grain size distribution of nanograins and weak tensile strains imposed to the film from the substrate. The whole set of results point to the interpretation of a dielectric response characteristic of mesoscopic structure, which is composed of clusters and nanodomains.     

Heat capacity study of relaxor PbMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript> in a wide temperature range

Heat capacity of the PbMg_1/3Nb_2/3O₃ compound is measured using the methods of adiabatic and differential scanning calorimetry in the temperature range 80–750 K. Two blurred anomalies on the C _p (T) dependence are observed in wide temperature intervals of 200–400 K and 500–700 K. The results of studies are discussed together with data on the structure and phonon spectrum in the framework of spherical random bond-random field model.     

Dielectric properties of (K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>)(Nb<Subscript>0.93</Subscript>Sb<Subscript>0.07</Subscript>)O<Subscript>3</Subscript> ferroelectric ceramics modified with BaTiO<Subscript>3</Subscript>

Processes of the polarization and repolarization of ferroelectric ceramics based on potassium sodium niobate in the region of infralow frequencies are discussed. The effect aging and subsequent annealing in a strong alternating electric field have on the nonlinearity of the dielectric response of a sample at different temperatures is determined.     

A comparative Raman study of 0.65(PbMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript>) -0.35(PbTiO<Subscript>3</Subscript>) single crystal and thin film

We report a comparative Raman study of 0.65(PbMg_1/3Nb_2/3O₃)-0.35(PbTiO₃) (PMN-0.35PT) single crystal and thin film. Raman spectra investigation indicates a change in bulk from the high temperature cubic to the tetragonal phase and then to the low temperature Mc monoclinic phase. The transition temperatures are in good agreement with the ones previously observed by dielectric measurements on the same sample. In contrast, we observe no phase transition to the monoclinic phase in the PMN-0.35PT 4000 Å thick film and only a cubic to tetragonal diffuse transition has been determined at high temperature. The enhanced stability of the tetragonal phase and the absence of low temperature monoclinic phase have been attributed to the in plane strain.     

Electric and magnetic properties of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/Pb(Zr<Subscript>0.52</Subscript>Ti<Subscript>0.48</Subscript>)O<Subscript>3</Subscript> bilayer thin films prepared by pulsed-laser deposition

CoFe₂O₄ (CFO) thin film with highly (111)-preferential orientation was first deposited on the silicon substrate by a pulsed-laser deposition, and then Pb(Zr_0.52Ti_0.48)O₃ (PZT) layers were deposited with different oxygen pressures to form the bilayer CFO/PZT nanocomposite thin films. X-ray diffraction showed that the PZT preferential orientation was strongly dependant on the oxygen pressure. The smooth film surface was obtained after depositing the CFO and PZT layers. The bilayer thin films exhibit good ferromagnetic and ferroelectric properties, and a low leakage current density of 0.004 μA/cm² at 50 kV/cm. The leakage current density curves show loops for the electric polarized field when the electric field reverses. PACS 77.84.Lf; 75.80+q; 81.05.Zx; 81.15.Fg     

Effect of the la concentration on the dielectric and optical properties of the transparent ferroelectric ceramics 75PbMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript>-25PbTiO<Subscript>3</Subscript>

The dielectric, optical, and electro-optical properties of transparent ferroelectric ceramics 75PbMg_1/3Nb_2/3O₃-25PbTiO₃ (75PMN-25PT) with different La concentrations (2, 3, and 4 at %) have been studied. It has been shown that all the samples under study undergo a diffuse phase transition, and the degree of diffuseness increases with an increase in the La concentration. The temperature dependences of the optical transmission in different regimes of applying an electric field and the quadratic electro-optical effect have been investigated. It has been found that, at room temperature, the maximum electro-optical effect is observed in the ceramics with a La concentration of 3 at %. This is explained by the fact that the measurement temperature is close to the Vogel-Fulcher temperature at which the minimum electric field is required to induce ferroelectric states from the relaxor phase.     

Lattice dynamics and ferroelectric instability in ordered and disordered PbSc<Subscript>1/2</Subscript>Ta<Subscript>1/2</Subscript>O<Subscript>3</Subscript> and PbSc<Subscript>1/2</Subscript>Nb<Subscript>1/2</Subscript>O<Subscript>3</Subscript> solid solutions

The dynamic Born charges and the frequency spectra of lattice oscillations in the crystals of ordered and disordered PbSc_1/2Ta_1/2O₃ (PST) and PbSc_1/2Nb_1/2O₃ (PSN) solid solutions have been calculated within the framework of the generalized Gordon-Kim model with allowance for the dipole and quadrupole polarizabilities. The phonon spectra of both compounds contain ferroelectric soft modes. The influence of various interactions on the magnitude of dynamic charges and ferroelectric instability in PSN and PST solid solutions has been studied and it is shown that both these charges and the ferroelectric instability are determined by the competition between long-range dipole-dipole interactions and short-range dipole-charge interactions, the determining role played by the interaction of Nb (Ta) cations and oxygen anions in the Nb-O (Ta-O) bond direction.     

Study of ferroelectric phase transitions in disordered PbSc<Subscript>1/2</Subscript>Nb<Subscript>1/2</Subscript>O<Subscript>3</Subscript> and PbSc<Subscript>1/2</Subscript>Ta<Subscript>1/2</Subscript>O<Subscript>3</Subscript> solid solutions

Ferroelectric phase transitions and thermodynamic properties of disordered PbSc_1/2Ta_1/2O₃ and PbSc_1/2Nb_1/2O₃ solid solutions have been investigated by the Monte Carlo method. The parameters of the effective Hamiltonian were calculated within the generalized Gordon-Kim model. The obtained values of the phase-transition temperatures and spontaneous polarization are in satisfactory agreement with the experimental data.     

Synthesis and characterization of micro/nanoscopic Pb(Zr<Subscript>0.52</Subscript>Ti<Subscript>0.48</Subscript>)O<Subscript>3</Subscript> fibers by electrospinning

Micro/nanoscopic Pb(Zr_0.52Ti_0.48)O₃ fibers were synthesized from commercially available zirconium n-pro-poxide, titanium isopropoxide, and lead 2-ethylhexanoate. Using xylene as a solvent, they were mixed to form a precursor solution with a suitable viscosity for electrospinning. The solution was analyzed using thermo-gravimetric and differential thermal methods. Ultra-fine fibers and mats were electrostatically drawn from the precursor solution. The as-deposited materials were sintered for 2 h at 400, 500, 600, 700 and 800 °C, respectively. Sintered mats or fibers were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), Auger electron spectroscopy (AES), Raman micro-spectrometry and scanning-probe microscopy (SPM). The SEM results revealed that the fibers had diameters varying from hundreds of nanometers to 10 m. Using AES, the elements Pb, Zr, Ti and O, as well as residual C, were detected on the surface of the fibers. Raman and XRD spectra indicated that the precursors began to transform into the intermediate pyrochlore phase at 400 °C, followed by the perovskite Pb(Zr_0.52Ti_0.48)O₃ phase above 600 °C. Scanning-probe microscopy (SPM), operated in the piezo-response imaging mode, revealed spontaneous polarization domains in the fibers, with diameters ranging from 100 to 500 nm. PACS 61.46.+w; 77.90.+k; 81.07.-b; 81.16.-c