Quantification of surface-bound proteins by fluorometric assay: Comparison with quartz crystal microbalance and amido black assay

Protein adsorption is of major and widespread interest, being useful in the fundamental understanding of biological processes at interfaces through to the development of new materials. A number of techniques are commonly used to study protein adhesion, but few are directly quantitative. Here we describe the use of Nano Orange, a fluorometric assay, to quantitatively assess the adsorption of bovine fibrinogen and albumin onto model hydrophilic (OH terminated) and hydrophobic (CH3 terminated) surfaces. Results obtained using this method allowed the calibration of previously unquantifiable data obtained on the same surfaces using quartz crystal microbalance measurements and an amido black protein assay. Both proteins were found to adsorb with higher affinity but with lower saturation levels onto hydrophobic surfaces. All three analytical techniques showed similar trends in binding strength and relative amounts adsorbed over a range of protein concentrations, although the fluorometric analysis was the only method to give absolute quantities of surface-bound protein. The versatility of the fluorometric assay was also probed by analyzing protein adsorption onto porous superhydrophobic and superhydrophilic surfaces. Results obtained using the assay in conjunction with these surfaces were surface chemistry dependent. Imbibition of water into the superhydrophilic coatings provided greater surface area for protein adsorption, although the protein surface density was less than that found on a comparable flat hydrophilic surface. Superhydrophobic surfaces prevented protein solution penetration. This paper demonstrates the potential of a fluorometric assay to be used as an external calibration for other techniques following protein adsorption processes or as a supplemental method to study protein adsorption. Differences in protein adsorption onto hydrophilic vs superhydrophilic and hydrophobic vs superhydrophobic surfaces are highlighted.     

Surface tailoring for controlled protein adsorption: effect of topography at the nanometer scale and chemistry

Protein adsorption behavior is at the heart of many of today's research fields including biotechnology and materials science. With understanding of protein-surface interactions, control over the conformation and orientation of immobilized species may ultimately allow tailor-made surfaces to be generated. In this contribution protein-surface interactions have been examined with particular focus on surface curvature with and without surface chemistry effects. Silica spheres with diameters in the range 15-165 nm with both hydrophilic and hydrophobic surface chemistries have been used as model substrates. Two proteins differing in size and shape, bovine serum albumin (BSA) and bovine fibrinogen (Fg), have been used in model studies of protein binding with detailed secondary structure analysis being performed using infrared spectroscopy (IR) on surface-bound proteins. Although trends in binding affinity and saturation values were similar for both proteins, albumin is increasingly less ordered on larger substrates, while fibrinogen, in contrast, loses secondary structure to a greater extent when adsorbing onto particles with high surface curvature. These effects are compounded by surface chemistry, with both proteins becoming more denatured on hydrophobic surfaces. Both surface chemistry and topography play key roles in determining the structure of the bound proteins. A model of the binding characteristics of these two proteins onto surfaces having differing curvature and chemistry is presented. We propose that properties of an adsorbed protein layer may be guided through careful consideration of surface structure, allowing the fabrication of materials/surface coatings with tailored bioactivity.     

Molecular packing of lysozyme,fibrinogen, and bovine serum albumin on hydrophilic and hydrophobic surfaces studied by infrared-visible sum frequency generation and fluorescence microscopy

Infrared-visible sum frequency generation (SFG) vibrational spectroscopy, in combination with fluorescence microscopy, was employed to investigate the surface structure of lysozyme, fibrinogen, and bovine serum albumin (BSA) adsorbed on hydrophilic silica and hydrophobic polystyrene as a function of protein concentration. Fluorescence microscopy shows that the relative amounts of protein adsorbed on hydrophilic and hydrophobic surfaces increase in proportion with the concentration of protein solutions. For a given bulk protein concentration, a larger amount of protein is adsorbed on hydrophobic polystyrene surfaces compared to hydrophilic silica surfaces. While lysozyme molecules adsorbed on silica surfaces yield relatively similar SFG spectra, regardless of the surface concentration, SFG spectra of fibrinogen and BSA adsorbed on silica surfaces exhibit concentration-dependent signal intensities and peak shapes. Quantitative SFG data analysis reveals that methyl groups in lysozyme adsorbed on hydrophilic surfaces show a concentration-independent orientation. However, methyl groups in BSA and fibrinogen become less tilted with respect to the surface normal with increasing protein concentration at the surface. On hydrophobic polystyrene surfaces, all proteins yield similar SFG spectra, which are different from those on hydrophilic surfaces. Although more protein molecules are present on hydrophobic surfaces, lower SFG signal intensity is observed, indicating that methyl groups in adsorbed proteins are more randomly oriented as compared to those on hydrophilic surfaces. SFG data also shows that the orientation and ordering of phenyl rings in the polystyrene surface is affected by protein adsorption, depending on the amount and type of proteins.     

Reversibly Controlling Preferential Protein Adsorption on Bone Implants by Using an Applied Weak Potential as a Switch

A facile method is needed to control the protein adsorption onto biomaterials, such as, bone implants. Herein we doped taurocholic acid (TCA), an amphiphilic biomolecule, into an array of 1D nano‐architectured polypyrrole (NAPPy) on the implants. Doping TCA enabled the implant surface to show reversible wettability between 152° (superhydrophobic, switch‐on state) and 55° (hydrophilic, switch‐off state) in response to periodically switching two weak electrical potentials (+0.50 and ?0.80 V as a switch‐on and switch‐off potential, respectively). The potential‐switchable reversible wettability, arising from the potential‐tunable orientation of the hydrophobic and hydrophilic face of TCA, led to potential‐switchable preferential adsorption of proteins as well as cell adhesion and spreading. This potential‐switchable strategy may open up a new avenue to control the biological activities on the implant surface.     

十八烷基聚氧乙烯表面空间结构和蛋白质吸附行为研究

为探讨聚合物-水界面十八烷基聚氧乙烯链(SPEO)空间结构和白蛋白选择性吸附行为的内在联系,本文采用聚甲基丙烯酸甲酯接枝十八烷基聚氧乙烯(PMMA-g-SPEO),通过不同热处理方式获得了具有“环形链”(A)和“尾形链”(B)结构的两种模型表面.在A表面,水相接触角随水化时间的延长而迅速降低,最终亲水性的界面可同时有效阻抗白蛋白和纤维蛋白原的吸附,但不呈现对白蛋白的选择性吸附;而在B表面,水相接触角随水化时间的延长变化不大,最终疏水性的界面可在有效阻抗纤维蛋白原的吸附同时,有效诱导白蛋白的选择性吸附,具有聚氧乙烯(PEO)阻抗非特异性吸附和十八烷基选择性吸附协同作用的特点.     

Control of protein adsorption: molecular level structural and spatial variables

The adsorption of fibrinogen (Fb) and bovine serum albumin onto polycrystalline Au coated with HS(CH2)3O(CH2CH2O)5CH3 was determined by surface plasmon resonance from bare Au (0% coverage) to the complete ( approximately 100% coverage) self-assembled monolayer (SAM). Both proteins exhibit similar adsorption curves with common onset ( approximately 60% coverage) and range ( approximately 60% to 80% coverage) of minimal protein adsorption. Reflection-absorption infrared spectroscopic data show that widespread order is not present in the films over this range of coverage, indicating loosely packed, bound oligomers that are uniformly distributed and fully screen the underlying substrate. On the basis of our data, we propose a mechanism of protein rejection by oligo(ethylene oxide) (OEO)-modified surfaces in terms of changes in free energy (DeltaGsystem; system = protein + surface) due to oligomer conformational constriction over an area greater than the contact area. Minimal protein adsorption corresponds to the maximum DeltaGsystem for a given compression. This controlled study of protein adsorption provides insights into the molecular level understanding of protein adsorption unavailable from previous polymer and comparative SAM studies.     

Fibrinogen adsorption on blocked surface of albumin

We have investigated the adsorption of albumin and fibrinogen onto PET (polyethylene terephthalate) and glass surfaces and how pre-adsorption of albumin onto these surfaces can affect the adsorption of later added fibrinogen. For materials and devices being exposed to blood, adsorption of fibrinogen is often a non-wanted event, since fibrinogen is part of the clotting cascade and unspecific adsorption of fibrinogen can have an influence on the activation of platelets. Albumin is often used as blocking agent for avoiding unspecific protein adsorption onto surfaces in devices designed to handle biological samples, including protein solutions. It is based on the assumption that proteins adsorbs as a monolayer on surfaces and that proteins do not adsorb on top of each other. By labelling albumin and fibrinogen with two different radioactive iodine isotopes that emit gamma radiation with different energies, the adsorption of both albumin and fibrinogen has been monitored simultaneously on the same sample. Information about topography and coverage of adsorbed protein layers has been obtained using AFM (Atomic Force Microscopy) analysis in liquid. Our studies show that albumin adsorbs in a multilayer fashion on PET and that fibrinogen adsorbs on top of albumin when albumin is pre-adsorbed on the surfaces.     

Cooperativity in the adsorption of cellulose ethers and fibrinogen at liquid-solid interfaces

The possibility of reducing fibrinogen adsorption to solid surfaces by competitive adsorption of cellulose ethers (EHEC, HEC) was investigated. The surface concentration of fibrinogen adsorbed onto hydrophilic and hydrophobic (methylized) glass was measured with an enzyme-linked immunosorbent assay. The immunoassay was calibrated by ellipsometry, using the initial mass transport limitation of adsorption for calculations of the maximum amount of adsorbed protein.At a hydrophobic surface, the presence of cellulose polymers caused a decrease of the adsorption of fibrinogen. The hydrophobic EHEC (cloud point 35°C) was most efficient and abolished surface-adsorption of the protein.At a hydrophilic surface, positive cooperativity was seen between fibrinogen and cellulose polymers. The hydrophilic HEC (cloud point >100°C) gave the most prominent effect.The results indicate that the affinity between a water soluble polymer or protein and a solid surface is not the only factor determining surface adsorption. The finding that there may be both positive and negative cooperativity in the adsorption of polymers shows the importance of polymer compatibility in layers of adsorbed polymers.     

Human plasma protein adsorption onto dextranized surfaces: a two-dimensional electrophoresis and mass spectrometry study

Protein adsorption is fundamental to thrombosis and to the design of biocompatible materials. We report a two-dimensional electrophoresis and mass spectrometry study to characterize multiple human plasma proteins adsorbed onto four different types of model surfaces: silicon oxide, dextranized silicon, polyurethane and dextranized polyurethane. Dextran was grafted onto the surfaces of silicon and polyurethane to mimic the blood-contacting endothelial cell glycocalyx surface. Surface topography and hydrophobicity/hydrophilicity were determined and analyzed using atomic force microscopy and water contact angle measurements, respectively. Using two-dimensional electrophoresis, we show that, relative to the unmodified surfaces, dextranization significantly inhibits the adsorption of several human plasma proteins including IGHG1 protein, fibrinogen, haptoglobin, Apo A-IV, Apo A-I, immunoglobulin, serum retinal-binding protein and truncated serum albumin. We further demonstrate the selectivity of plasma protein adsorbed onto the different functionalized surfaces and the potential to control and manipulate proteins adsorption on the surfaces of medical devices, implants and microfluidic devices. This result shows that adsorption experiments using a single protein or a binary mixture of proteins are consistent with competitive protein adsorption studies. In summary, these studies indicate that coating blood-contacting biomedical applications with dextran is an effective route to reduce thrombo-inflammatory responses and to surface-direct biological activities.     

Binding of salivary proteins and oral bacteria to hydrophobic and hydrophilic surfaces in vivo and in vitro

Chemical modifications of mineral surfaces were performed in order to gain insight into what surface properties are decisive of the accumulation of dental plaque. A non-charged, hydrophilic surface was made by two consecutive plasma polymerizations, firstly with allyl alcohol, secondly with acrylic acid, followed by adsorption of a poly(ethylene glycol)-poly(ethylene imine) adduct. A strongly hydrophobic surface was obtained by plasma polymerization of hexamethyldisiloxane. Ellipsometry was used to monitor protein interaction with the surfaces. The hydrophilic surface gave very little adsorption of both a model protein, IgG, and of saliva proteins. The hydrophobic surface, on the other hand, adsorbed high amounts of both types of proteins. In vitro adhesion of an oral bacterium,S. mutans, as well as in vivo studies, gave the opposite result, the hydrophobic surface giving less adhesion and less plaque accumulation than the hydrophilic surface. A tentative explanation of this behavior is that the saliva proteins that bind to the hydrophobic surface adsorb in an unnatural conformation which does not favor bacteria adherence.     

Protein adsorption on supported phospholipid bilayers

Quartz crystal microbalance with dissipation (QCM-D) measurements were used to investigate the adsorption of human fibrinogen, human serum albumin, bovine hemoglobin, horse heart cytochrome c, human immunoglobulin (hIgG), and 10% fetal bovine serum on supported bilayers of egg-phosphatidylcholine (eggPC) lipids. For comparison the adsorption of fibrinogen and hIgG to eggPC bilayers was also studied with surface plasmon resonance (SPR). The supported bilayers were formed in situ by vesicle adhesion and spontaneous fusion onto a SiO(2) surface. The supported lipid bilayer is highly protein resistant: The irreversible adsorption measured with the QCM-D technique was below the detection level, while reversible protein adsorption was detected for all the proteins in the range 0.3-4% of the saturation coverage on a hydrophobic thiol monolayer on gold. The adsorbed amounts were slightly higher for the SPR measurements. Possible mechanisms for the protein resistance of eggPC bilayers are briefly discussed.     

Interaction of Plasma Proteins with Tri‐quaternary Ammonium Salt Cationic Surfactant Studied by QCM‐D

A tri‐quaternary ammonium salt cationic surfactant was synthesized. Its structure was confirmed by using Fourier‐transform infrared spectroscopy, ¹H nuclear magnetic resonance spectroscopy, and X‐ray photoelectron spectroscopy analyses. Three model surfaces, including Au‐CH₃, Au‐OH and Au‐COOH, were fabricated. Adsorptions of surfactant on the three model surfaces and subsequent plasma proteins adsorption were investigated by quartz crystal microbalance with dissipation (QCM‐D). The mass of surfactant on the Au‐COOH surface was the largest, followed by that on the Au‐CH₃ surface, and that on the Au‐OH surface. These results suggested that the main driving force of surfactant immobilization was electrostatic interaction followed by hydrophobic interaction. Based on the results obtained, we concluded that the protein mass adsorbed on Au‐CH₃‐ S , Au‐OH‐ S , and Au‐COOH‐ S surfaces depended on the protein size and orientation. The mass and thickness of S on the Au‐COOH surface is the largest and the protein adsorption capacity of Au‐COOH‐ S surface is inferior to that of Au‐CH₃‐ S . The Au‐COOH‐ S surface could inhibit lysozyme adsorption, maintain the adsorption balance of bovine serum albumin, and induce fibrinogen‐binding protein adsorption.     

In situ conformational analysis of fibrinogen adsorbed on Si surfaces

Fibrinogen is a major plasma protein. Previous investigations of structural changes of fibrinogen due to adsorption are mostly based on indirect evidence after its desorption, whereas our measurements were performed on fibrinogen in its adsorbed state. Specific enzyme-linked immunosorption experiments showed that the amount of adsorbed fibrinogen increased as the surface became more hydrophobic. Atomic force microscopy (AFM) investigations revealed the trinodular shape of fibrinogen molecules adsorbed on hydrophilic surfaces, whereas all of the molecules appeared globular on hydrophobic surfaces. The distribution of secondary structures in adsorbed fibrinogen was quantified by in situ Fourier-transform infrared (FTIR) analysis. Substrates of identical chemical bulk composition but different surface hydrophobicity permit direct comparison among them. Adsorption properties of fibrinogen are different for each degree of hydrophobicity. Although there is some increase of turn structure and decrease of β-sheet structure, the secondary structure of adsorbed fibrinogen on hydrophilic surface turned out to be rather similar to that of the protein in solution phase with a major -helix content. Hydrophilic surfaces exhibit superior blood compatibility as required for medical applications.     

Fibronectin displacement at polymer surfaces

The interactions of fibronectin with thin polymer films are studied in displacement experiments using human serum albumin. Fibronectin adsorption and exchange on two different maleic anhydride copolymer surfaces differing in hydrophobicity and surface charge density have been analyzed by quartz crystal microbalance and laser scanning microscopy with respect to adsorbed amounts, viscoelastic properties, and conformation. Fibronectin is concluded to become attached onto hydrophilic surfaces as a "softer", less rigid protein layer, in contrast to the more rigid, densely packed layer on hydrophobic surfaces. As a result, the fibronectin conformation is more distorted on the hydrophobic substrates together with remarkably different displacement characteristics in dependence on the adsorbed fibronectin surface concentration and the displacing albumin solution concentration. While the displacement kinetic remains constant for the strongly interacting surface, an acceleration in fibronectin exchange is observed for the weakly interacting surface with increasing fibronectin coverage. For displaced amounts, no change is determined for the hydrophobic substrate, in contrast to the hydrophilic substrate with a decrease of fibronectin exchange with decreasing coverage leading finally to a constant nondisplaceable amount of adsorbed proteins. Furthermore, the variation of the albumin exchange concentration reveals a stronger dependence of the kinetic for the weakly interacting substrate with higher rates at higher albumin concentrations.     

Adsorption of albumin and IgG to porous and smooth titanium

The possibility to load submicrometer porous titanium surfaces with relatively small proteins, albumin and immunoglobulin G (IgG) was investigated. The loading ability is of interest due to the possibility of slow release of molecules from biomaterial surfaces, and may be important for the manipulation of wound healing around prostheses. Iodine-125 (125I) labeled albumin and IgG were adsorbed onto smooth and to porous titanium with a pore diameter of 200-300 nm. The smooth and porous surfaces were divided into three groups: hydrophilic, hydrophobic, or to amine-terminated silane (3-aminopropyltriethoxysilane) that bound proteins via glutaraldehyde. The protein solution pH and protein concentrations were varied, and the adsorption experiments made without or in the presence of calcium and magnesium ions. The adsorbed amounts were quantified with a gamma counter. Two to eleven times more proteins adsorbed onto porous than smooth surfaces and the adsorbed amounts increased with increasing protein concentration (0.1-10 mg/ml) during a constant incubation time. The elutability by sodium dodecyl sulphate (SDS) was incomplete on porous surfaces.     

Protein coverage on polymer nanolayers leading to mesenchymal stem cell patterning

Interactions of gelatin and albumin with a photo-reactive diphenylamino-s-triazine bridged p-phenylene vinylene polymer (DTOPV) were examined by using surface plasmon resonance (SPR) spectroscopy to explore the effect of the polymer structure on protein coverage of DTOPV nanofilms. The SPR data revealed a significant increase of gelatin adsorption on UV-DTOPV nanofilms, while the adsorption of albumin was decreased by UV exposure in the time frame of the experiment. We also found that the selective adsorption of these proteins was highly dependent on the protein concentration; the highest selectivity of protein adsorption was obtained at the lowest concentration (3.5 μg ml(-1)), while no selective adsorption was confirmed at high concentrations (350 and 1000 μg ml(-1)). The selective attachment of mesenchymal stem cells (MSCs) was directly correlated with the selective adsorption of these proteins onto DTOPV nanofilms. The MSCs attachment onto UV-DTOPV films was promoted with only small mass coverage of gelatin, which led to MSC patterning onto the patterned DTOPV nanofilms successfully. The role of cell adhesion proteins that we found in this study will be a clue to elucidate the complex response of biomolecules on functional polymer nanolayers, and contribute to build up biocompatible surfaces on various advanced materials for the sake of cell engineering and medical implants.     

In situ adsorption studies of a 14-amino acid leucine-lysine peptide onto hydrophobic polystyrene and hydrophilic silica surfaces using quartz crystal microbalance, atomic force microscopy, and sum frequency generation vibrational spectroscopy

The adsorption of a 14-amino acid amphiphilic peptide, LK14, which is composed of leucine (L, nonpolar) and lysine (K, charged), on hydrophobic polystyrene (PS) and hydrophilic silica (SiO2) was investigated in situ by quartz crystal microbalance (QCM), atomic force microscopy (AFM), and sum frequency generation (SFG) vibrational spectroscopy. The LK14 peptide, adsorbed from a pH 7.4 phosphate-buffered saline (PBS) solution, displayed very different coverage, surface roughness and friction, topography, and surface-induced orientation when adsorbed onto PS versus SiO2 surfaces. Real-time QCM adsorption data revealed that the peptide adsorbed onto hydrophobic PS through a fast (t < 2 min) process, while a much slower (t > 30 min) multistep adsorption and rearrangement occurred on the hydrophilic SiO2. AFM measurements showed different surface morphologies and friction coefficients for LK14 adsorbed on the two surfaces. Surface-specific SFG spectra indicate very different ordering of the adsorbed peptide on hydrophobic PS as compared to hydrophilic SiO2. At the LK14 solution/PS interface, CH resonances corresponding to the hydrophobic leucine side chains are evident. Conversely, only NH modes are observed at the peptide solution/SiO2 interface, indicating a different average molecular orientation on this hydrophilic surface. The surface-dependent difference in the molecular-scale peptide interaction at the solution/hydrophobic solid versus solution/hydrophilic solid interfaces (measured by SFG) is manifested as significantly different macromolecular-level adsorption properties on the two surfaces (determined via AFM and QCM experiments).     

A Commercial Nonbinding Surface Effectively Reduces Fibrinogen Adsorption but Does Not Prevent Platelet Adhesion to Fibrinogen

A commercial nonbinding surface effectively prevents protein adsorption; however, the platelet phenotype on this surface has yet to be defined. This study evaluates platelet adhesion and adsorption of several plasma/extracellular matrix (ECM) proteins to the nonbinding surface compared to other commonly used nontreated and high-binding surfaces. Platelet adhesion to uncoated microplates and those coated with fibrinogen or collagen is quantified by colorimetric assay. The binding capacity of the examined surfaces for plasma/ECM proteins is evaluated by measuring the relative and absolute protein adsorption. Compared to other surfaces, the nonbinding surface effectively prevents platelet adsorption, i.e. by 61-93% (Enzyme-Linked Immunosorbent Assay, ELISA), and reduces platelet adhesion, i.e. by 92%, when not coated with any protein. The nonbinding surface also decreases platelet deposition on collagen (up to 31%), but not fibrinogen. The nonbinding surface seems to be more of a low-fouling than nonfouling material, as it is able to reduce fibrinogen adsorption but not prevent platelet adhesion to fibrinogen. This feature should be considered when using the nonbinding surface for in vitro platelet testing.     

Click-chemistry for surface modification of monodisperse-macroporous particles

In this study, click chemistry was proposed as a tool for tuning the surface hydrophilicity of monodisperse-macroporous particles in micron-size range. The monodisperse-porous particles carrying hydrophobic or hydrophilic molecular brushes on their surfaces were obtained by the proposed modification. Hydrophilic poly(glycidyl methacrylate-co-ethylene dimethacrylate), poly(GMA-co-EDM) particles were hydrophobized by the covalent attachment of poly(octadecyl acrylate-co-propargyl acrylate), poly(ODA-co-PA) copolymer onto the particle surface via triazole formation by click chemistry. In the second part, Hydrophobic poly(4-chloromethylstyrene-co-divinylbenzene), poly(CMS-co-DVB) particles were hydrophilized by the covalent attachment of poly(vinyl alcohol), PVA onto their surface also via triazole formation by click chemistry. The presence of PVA and poly(ODA-co-PA) copolymer on the corresponding particles was shown by FTIR-DRS. After click-coupling reactions applied for both hydrophobic poly(CMS-co-DVB) and hydrophilic poly(GMA-co-EDM) particles, the marked changes in surface polarity were shown by contact angle measurements. Protein adsorption characteristics of plain and modified particles were investigated for both materials. In the isoelectric point of albumin, the non-specific albumin adsorption decreased from 225 to 80 mg/g by grafting PVA onto the poly(CMS-co-DVB) beads. On the other hand, the non-specific albumin adsorption onto the plain poly(GMA-co-EDM) beads increased from 50 to 400 mg/g by the covalent attachment of poly(ODA-co-PA) copolymer onto the bead-surface via click chemistry. The protein adsorption behavior was efficiently regulated by the covalent attachment of appropriate molecular brushes onto the surfaces of selected particles. The results indicated that "click chemistry" was an efficient tool for controlling the polarity of monodisperse-macroporous particles.     

Kinetics of conformational changes of fibronectin adsorbed onto model surfaces

Fibronectin (FN), a large glycoprotein found in body fluids and in the extracellular matrix, plays a key role in numerous cellular behaviours. We investigate FN adsorption onto hydrophilic bare silica and hydrophobic polystyrene (PS) surfaces using Fourier transform infrared spectroscopy-attenuated total reflection (FTIR-ATR) in aqueous medium. Adsorption kinetics using different bulk concentrations of FN were followed for 2h and the surface density of adsorbed FN and its time-dependent conformational changes were determined. When adsorption occurs onto the hydrophilic surface, FN molecules keep their native conformation independent of the adsorption conditions, but the amount of adsorbed FN increases with time and the bulk concentration. Although the protein surface density is the same on the hydrophobic PS surface, this has a strong impact on the average conformation of the adsorbed FN layer. Indeed, interfacial hydration changes induced by adsorption onto the hydrophobic surface lead to a decrease in unhydrated beta-sheet content and cause an increase in hydrated beta-strand and hydrated random domain content of adsorbed FN. This conformational change is mainly dependent on the bulk concentration. Indeed, at low bulk concentrations, the secondary structures of adsorbed FN molecules undergo strong unfolding, allowing an extended and hydrated conformation of the protein. At high bulk concentrations, the molecular packing reduces the unfolding of the stereoregular structures of the FN molecules, preventing stronger spreading of the protein.