Electrical Conductance of Fast Extrusion Furnace Carbon Black-Loaded Styrene-Butadiene Rubber during Swelling in Kerosene

The effect of swelling in kerosene on the electrical conductance of 60, 80, and 100 part per hundred parts of rubber by weight of Fast Extrusion Furnace (FEF) carbon black-loaded styrene-butadiene rubber (SBR, 1502) was studied. It was found that there is a characteristic time of swelling after which a sudden decrease in conductivity appears. An ideal and simple model is suggested to calculate the carbon-carbon interspacing distance, D, in the carbon/rubber matrix. The dependence of D on the swelling time is also discussed.     

Effect of chitosan derivatives as rubber antioxidants for increasing durability

A series of chitosan derivatives, namely polydiethylamino-ethylmethacrylate-chitosan-graft-copolymer (chitosan-g-DEAEMA), polycarboxy-chitosan-graft copolymer (chitosan-g-COOH), polyvinyl alcohol chitosan-graft-copolymer (chitosan-g-VOH), and carboxymethyl-chitosan (CM-chitosan), were synthesized and investigated as antioxidants for natural rubber (NR) and acrylonitrile butadiene rubber (NBR) mixes and vulcanizates to increase their durability. The rheometric characteristics of the rubber mixes were determined using an oscillating disc rheometer. The physico-mechanical properties of the rubber vulcanized were measured before and after exposure to thermal oxidative aging. It was found that the CM-chitosan had an accelerating effect on the curing process of NR and NBR. Also, the investigated polymers enhanced the properties of rubbers (NR and NBR) especially after ageing up to 7 days compared with commercial antioxidants, such as phenyl ß-naphthylamine (PßN) and N-isopropel-Nphenyl-p-phenylene diamine (IPPD) which are used in the rubber industry. After ageing, the retained values of tensile strength, modulus at 100 % strain, and elongation at break were improved. The optimum concentration of the investigated compounds used to give good properties was found to be 1–2 parts per 100 of rubber (phr). In addition, these prepared polymers showed a decrease in the equilibrium swelling of rubber in toluene which is the proper solvent and consequently increases the crosslink density for rubbers.     

Positronium as a tool to monitor changes of chemical structure

The applicability of positron annihilation spectroscopy for chemical structural problems is demonstrated by two examples: For the swelling dynamics of an amphiphilic polymer network, very quick structural changes were indicated by positronium lifetime parameters at very low swelling ratios and a hydration mechanism was proposed accordingly. For the series [Fe_xZn_1−x(propyltetrazole)₆](BF₄)₂(x=1, 0.6, 0.4, 0.1, 0), changes in the dynamic structure were revealed by positronium lifetime spectroscopy. For compounds of x>0, temperature-induced spin-crossover was detected.     

双二苷酰胺从硝酸溶液中萃取Eu(Ⅲ)和Am(Ⅲ)

采用混合酸酐法合成了两种双二苷酰胺(bisdiglycolamide, BisDGA)萃取剂: N,N,N'',N''-四正辛基-N',N″-乙二基-双二苷酰胺(TOE-BisDGA)和N,N,N'',N''-四正辛基-N',N″-间苯二甲基-双二苷酰胺(TOX-BisDGA). 以磺化煤油和正辛醇混合溶液(体积比 90∶10)作稀释剂, 研究了它们在硝酸溶液中对Eu(Ⅲ)和Am(Ⅲ), 以及自身对HNO₃的萃取行为. 结果表明, 2种BisDGAs对HNO₃均有一定萃取, 当酸度不超过1.0 mol/L时, 二者形成1∶1型的萃合物. 随HNO₃浓度增加, Eu(Ⅲ)和Am(Ⅲ)的萃取分配比增加. 相同条件下, TOE-BisDGA对Eu(Ⅲ)和Am(Ⅲ)的萃取能力强于TOX-BisDGA. 斜率分析表明TOE-BisDGA和TOX-BisDGA与Eu(Ⅲ)和Am(Ⅲ)均形成2∶1型的萃合物. 温度升高, 萃取分配比下降, 萃取反应是放热反应. 2种BisDGAs对Eu(Ⅲ)的亲和力强于对Am(Ⅲ)的亲合力, 表明BisDGAs对Eu(Ⅲ)有一定的选择性. 同时, 研究了BisDGAs萃取Eu(Ⅲ)和Am(Ⅲ)的机理, 给出了表观萃取平衡常数和萃取反应热力学函数ΔH, ΔS和ΔG的值. 此外, 还对TOE-BisDGA和TOX-BisDGA与Eu(Ⅲ)形成的配合物进行了红外和紫外光谱分析.     

N-vinyl-2-pyrrolidone and methacrylonitrile copolymers: nuclear magnetic resonance characterization

The copolymers of N-vinyl-2-pyrrolidone and methacrylonitrile (V/N) were prepared by free radical bulk polymerisation. The copolymer composition was determined from the quantitative ¹³C{¹H} NMR spectrum. The reactivity ratios for N-vinyl-2-pyrrolidone (V) and methacrylonitrile (N) were found to be r_V=0.04, r_N=1.56. The complete spectral assignment of the overlapped and complex carbon and proton NMR spectra were done with the help of two dimensional ¹³C–¹H Heteronuclear Single Quantum Correlation Spectroscopy (HSQC) and Total Correlation Spectroscopy (TOCSY). Distortionless Enhancement by Polarization Transfer (DEPT) was used to differentiate between the methylene, the methine and the methyl carbon resonance signals of the copolymers.     

Chemical modification of butyl rubber. II. Structure and properties of poly(ethylene oxide)-grafted butyl rubber

Poly(ethylene oxide)-grafted butyl rubbers (IIR-g-PEOs), which were synthesized from potassium salt of polyethylene glycol monomethyl ether (PEGM) and chlorinated butyl rubber, were found to behave like thermoplastic elastomers. The poly(ethylene oxide) (PEO) content of these amphiphilic polymers was ca. 10 wt %, and their PEO lengths were 750, 2000, and 5000, respectively. The grafted segments of PEO in butyl rubber (IIR) aggregated to form the PEO domains in IIR matrix. At constant PEO content, the longer the PEO segment length, the larger the size and the crystallinity of PEO domains became. This PEO domain worked as a cross-linking site and a reinforcing filler. The degree of swelling in water of IIR-g-PEO film that was prepared from PEGM-5000 was largest, but its emulsification ability was smallest among them. © 1995 John Wiley & Sons, Inc.     

Effect of high-temperature curing on the crosslink structures and dynamic mechanical properties of gum and N330-filled natural rubber vulcanizates

The effects of high-temperature curing and overcuring on the cure characteristics, crosslink structure, physical properties and dynamic mechanical properties (DMPs) of gum and carbon black (N330) filled natural rubber (NR) vulcanizates cured with conventional (CV), semi-efficient (SEV) and efficient (EV) cure systems, which have about the same total crosslink densities under a moderate curing temperature of 150°C, were investigated. The gum NR vulcanizates cured with CV, SEV and EV curing systems have about the same glass transition temperature (T_g) and tan δ values below the temperature of about 0°C, but showed some apparent differences in the tan δ values increasing in the order CVG′ and tan δ values above T_g higher than those of the gum NR vulcanizates.

High-temperature curing and overcuring cause decreases to various extents in the cure plateau torque, Shore A hardness, 300% modulus and tensile strength, and lead to apparent changes in the DMPs. Typically, there is an increase in T_g of all three kinds of gum and N330-filled NR vulcanizates because of changes in the total crosslink densities and crosslink types. The CV vulcanizates show the most significant change in cure characteristics, physical properties and DMPs since the highest content of polysulfidic crosslinks appears in the CV vulcanizate, causing the highest level of reversion and having a dominant effect on the properties.     

反式丁戊橡胶改性航空轮胎侧胶的结构与性能

采用反式-1,4-丁二烯-异戊二烯共聚橡胶（简称反式丁戊橡胶,TBIR）改性航空轮胎侧胶[天然橡胶（NR）/顺丁橡胶（BR）（质量比80/20）],研究了NR/BR/TBIR混炼胶的结晶行为、力学性能、硫化特性及硫化胶的物理机械性能、动态力学性能和填料分散性.结果表明,相比NR/BR并用胶,结晶性TBIR的并用赋予NR/BR/TBIR混炼胶较高的格林强度和杨氏模量.NR/BR/TBIR混炼胶工艺正硫化时间延长,交联密度提高.TBIR用量范围内,NR/BR/TBIR硫化胶300%定伸应力提高7%,耐屈挠疲劳性能提高35%~50%,滚动阻力降低.m（NR）/m（BR）/m（TBIR）为80/10/10硫化胶具有更好的综合力学性能及耐热氧老化性能.随着硫化时间的延长,NR/BR/TBIR（80/10/10）硫化胶较NR/BR（80/20）硫化胶100%定伸应力提高18%以上,NR/BR体系的耐屈挠疲劳性降低近60%,而NR/BR/TBIR（80/10/10）体系仍能保持原来的50%;反映滚动阻力的60℃损耗因子降低8%~14%,反映抗湿滑性的0℃损耗因子保持不变.填料分散度得到改善,填料聚集体尺寸降低.NR/BR/TBIR（80/10/10）硫化胶具有更好的耐长时间硫化的特性.     

Phase transformation on heating of an aged cement paste

The standard cement paste (C-43-St) was studied previously by static heating, SH, immediately after 1 month hydration at w/c = 0.4 [J. Therm. Anal. Calorim. 69 (2002) 187]. This paste after 5-year ageing (unprotected from contact with air) was subject to thermal analysis in air and in argon (DTA, DTG and TG), to XRD at various temperatures, T, in a high temperature chamber, to mass spectroscopy (MS) and to IR spectroscopy. The aim of this study was to compare the results of SH (fresh paste) and of TG (the aged one), to verify the assumptions made on SH interpretation and to check the change in hydration products with ageing as measured by phase transformation on heating (ΔM versus the final mass). The sorbed water (EV), escaping at 110 °C from the fresh paste, was bound on ageing with a higher energy and escaped at higher temperatures. The joint water content of hydrates and of C-S-H gel increased on ageing by 1–2% in the dense paste C-43-St and did not change in the less compact one C-43-I. C-S-H gel transformed on heating above 600 °C into C₂S and C₃S. Portlandite content did not change on ageing. In the air atmosphere it became partly carbonated, which was accompanied by an increase in mass between 500 and 600 °C. Carbon dioxide and/or carbonate ions to form carbonates, were sorbed during ageing and were present in the aged paste in some form undetectable by XRD (amorphous or crypto-crystalline). Sensitivity to carbonation ΔM(700–800 °C) increased highly with ageing.     

Thermal degradation and pyrolysis study of brominated butyl rubber‐based damping material

This paper deals with the thermal stability and decomposition behavior of brominated butyl rubber‐based damping material (BRP). The raw materials, butyl rubber matrix (IIR) and brominated phenolic resin (PF), were also investigated as control. IIR shows one decomposition stage, while PF shows four weight loss stages. Flynn‐Wall‐Ozawa calculation indicates that BRP has thermal stability between IIR and PF. Thermogravimetric analysis–Fourier transform infrared (TGA‐FTIR) and pyrolysis–gas chromatography/mass spectrometry (GC/MS) were used to investigate the volatile products under nitrogen atmosphere. As expected, BRP shows combined thermal decomposition behavior of both IIR and PF. The degradation mechanism of BRP was proposed, which is not significantly influenced by the incorporation of PF. The application stability of BRP is worth to be noticed since the post‐cure effect, that is, the free radicals remained from vulcanization would cause additional cross‐linking when stored at 80°C to 120°C.     

The influence of nano silica particles on gamma-irradiation ageing of elastomers based on chlorosulphonated polyethylene and acrylonitrile butadiene rubber

The goal of this work was to study gamma irradiation ageing of rubber blends based on acrylonitrile butadiene rubber (NBR) and chlorosulphonated polyethylene rubber (CSM) reinforced by silica nano particles. The NBR/CSM compounds (50: 50, w/w) filled with different content of filler (0–100 phr) were crosslinked by sulfur. The vulcanization characteristics were assessed using the rheometer with an oscillating disk. The vulcanizates were prepared in a hydraulic press. The obtained materials were exposed to the different irradiation doses (100, 200, 300 and 400 kGy). The mechanical properties (hardness, modulus at 100% elongation, tensile strength and elongation at break) and swelling numbers were assessed before and after gamma irradiation ageing.     

稻壳基二氧化硅/碳复合材料的表面改性及对天然橡胶的影响

以稻壳基二氧化硅/碳复合材料(SiCB)作为天然橡胶(NR)的补强填料, 采用表面化学改性的方法将天然乳胶(NRL)接枝到SiCB表面, 改善其与NR基体的相容性. 研究了不同处理方法对接枝NRL效率的影响, 以及填料填入NR后对硫化橡胶力学性能的影响. 结果表明, 经过硝酸和γ-(甲基丙烯酰氧)丙基三甲氧基硅烷(γ-MPTMS)预处理, NRL能高效接枝在SiCB表面, 得到的样品SiCB_MR10比未处理的SiCB_P有更强的补强能力. 硫化胶NR/SiCB_MR10的拉伸强度、 300%定伸和撕裂强度较NR/SiCB_P分别提高了61.06%, 27.15%和15.90%, 与传统炭黑产品N774填充的硫化胶NR/N774的力学性能相近. 经过NRL接枝改性的SiCB_MR10具有替代商业炭黑的应用前景.     

Effect of polyvinylchloride on the properties of rubber vulcanizates

Natural rubber (NR) and styrene-butadiene rubber (SBR) were compounded with polyvinylchloride (PVC). Some physico-mechanical and dielectric properties of resulting rubber vulcanizates were measured. It was found that the addition of PVC to both NR and SBR results in slight decreases in tensile strength and elongation at break but a marked increase in oil-resistance of the vulcanizates. Moreover, the addition of PVC to NR slightly increases both dielectric constant and dielectric losses while the addition of PVC to SBR loaded with 50 phr carbon black (HAF) lowers these parameters. Both rubber blends, especially NR, show a reasonable stability with ageing.     

Study on damping properties of HVBR/EVM blends prepared by in situ polymerization

In comparison with normal damping rubbers such as natural rubber (NR), styrene butadiene rubber (SBR), isobutylene isoprene rubber (IIR) etc., Mo-based high vinyl polybutadiene rubber (HVBR) with high loss factor, excellent aging resistance and glass transition temperature closer to room temperature, is a promising damping material. The effective damping temperature range of HVBR could be further broadened by blending with ethylene-vinyl acetate (EVM) and the effects of blending methods (in situ polymerization blending or mechanical blending) and blending ratios on the damping properties and physical properties of HVBR/EVM blended rubber were studied. HVBR/EVM in situ polymerization blends was prepared by butadiene coordination polymerization by Mo-base catalyst in a toluene solution of EVM. The results of dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM) of the blended vulcanizates via in situ polymerization blending revealed that the compatibility between HVBR and EVM was improved compared with that of the blended vulcanizates via the traditional mechanical blending method. The two phases of HVBR/EVM in situ polymerization blends had good dispersion and uniformity, the damping temperature range was significantly expanded, and the peak and valley of the damping temperature range were greatly improved. A blending ratio of HVBR/EVM900 = 100/40 showed the best damping properties and the effective damping temperature range (tanδ>0.3) was extended from −6.6 °C to 39.4 °C.     

Colouring Agents for SBR Vulcanizates and Their Effects on Ageing and UV Radiation Resistance

Summary: Metal free and some metal-perylene polymers as well as some metal phthalocyanine polymers were incorporated into styrene butadiene rubber (SBR) compounds as colouring agents. The ageing and UV resistance of the vulcanizates obtained were studied in terms of their mechanical properties. The results obtained revealed that cobalt perylene and cobalt phthalocyanine polymers showed superior performance in SBR vulcanizates against thermal ageing and UV radiation. The optimum concentration of cobalt phthalocyanine polymer was found to be 1 phr (parts per hundred parts of rubber).     

g-CN体系的准粒子能带结构和光学特性

利用多体格林函数理论,本文研究了二维CN体系(包括triazine和tri-s-triazine)的激发态特性。通过GW方法,我们计算了准粒子的能量。考虑电子-空穴相互作用,通过求解Bethe-Salpeter方程,我们获得了激发态能量和光谱。我们发现,在这两种CN体系的价带中,σ轨道和π轨道之间的交换作用非常强烈。由于占据的σ轨道和π轨道之间的准粒子修正量非常不同,因此,为了得到准确的带隙值和光谱,我们需要对这两种轨道开展精确的GW计算。与单层的CN体系相比,双层结构中层与层之间的范德华相互作用使带隙值降低了0.6 eV,而光吸收谱红移了0.2 eV,这是由于双层结构具有更小的激子束缚能。我们计算的吸收峰的位置与实验结果符合很好。实验中的吸收峰主要是由深能级的π轨道到π^*轨道的跃迁形成的。π→π^*跃迁和σ→π^*跃迁之间的耦合能够在长波长范围产生弱的吸收尾巴,如果调整入射光的极化方向,由σ→π^*跃迁产生的高强度的吸收峰将会在更低能量处出现。     

A STUDY ON THE MORPHOLOGY AND PROPERTIES OF IPP/IIR BLENDS

The effect of isobutylene-isoprene rubber (IIR) on the crystallizing behavior of isotactic polypropylene (IPP) as well as the morphology of the blends in relation with its properties have been studied by DSC, WAXD, polarized light microscope, SEM and mechanical properties test. The experimental results show that IIR has slight influence on melting point, crystallinity, crystallization rate of IPP. It seems certain that IIR has not entered into IPP phase in melt state. IIR has retarding action on the growth of IPP crystal and is an effective nucleating agent of IPP spherulites. The impact strength of the blend increases rapidly with IIR content more than 30 parts; the tensile strength of the blend, however, decreases as IIR content increases. The temperature and time of alter heat-treatment also have great influence on the impact strength of the blend. The impact strength of IPP/IIR (100/20) heat-treated at about 130℃for 2h is 5 times as high as that of the untreated blend.     

In situ Carbon Modification of g-C3N4 from Urea co-Crystal with Enhanced Photocatalytic Activity Towards Degradation of Organic Dyes Under Visible Light

An in situ strategy was introduced for synthesizing carbon modified graphitic carbon nitride(g-C₃N₄) by using urea/4-aminobenzoic acid(PABA) co-crystal(PABA@Urea) as precursor materials. Via co-calcination of the PABA co-former and the urea in PABA@Urea co-crystals, C guest species were generated and compounded into g-C₃N₄ matrix in situ by replacing the lattice N of the carbon nitride and forming carbon dots onto its layer surface. The carbon modification dramatically enhanced visible-light harvesting and charge carrier separation. Therefore, visible light photo-catalytic oxidation of methylene blue(MB) pollution in water over the carbon modified g-C₃N₄(C/g-C₃N₄) was notably improved. Up to 99% of methylene blue(MB) was eliminated within 60 min by the optimal sample prepared from the PABA@Urea co-crystal with a PABA content of 0.1%(mass ratio), faster than the degradation rate over bare g-C₃N₄. The present study demonstrates a new way to boost up the photocatalysis performance of g-C₃N₄, which holds great potential concerning the degradation of organic dyes from water.     

Effect of Electron Beam Irradiation and Ethylene Vinyl Acetate Copolymer on the Properties of NBR/HDPE Blends

The mechanical and physical properties of blends based essentially on nitrile butadiene rubber (NBR) and different ratios of high density polyethylene (HDPE) up to 25 parts per hundred part of rubber (phr) before and after electron beam irradiation were investigated. The values of tensile strength (TS), tensile modulus at 50% elongation (M₅₀), hardness and gel fraction % (GF%) of NBR/HDPE blends were increased with both irradiation dose and by increasing the content of HDPE in the blends. On the other hand, the values of elongation at break (E _b ) were decreased with both irradiation dose and the content of HDPE in the blends. By loading NBR/HDPE (100/25) blend with ethylene vinyl acetate (EVA) copolymer the mechanical and physico-chemical properties were improved. Moreover, the degree of improvement is proportional to the loading content of EVA.     

碳包覆碳酸钴锂离子电池负极材料的制备及电化学性能

以葡萄糖作为碳源,通过简单的水热反应获得菱形碳包覆碳酸钴(CoCO₃/C)复合材料,并研究了其作为锂离子电池负极材料的电化学性能.晶型和表面形貌通过X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)进行表征,用热重-差热分析法(TG-DTA)来测试CoCO₃/C材料中碳的含量,用拉曼光谱分析无定型碳的存在. Barrett-Joyner-Halenda (BJH)则用来分析材料的孔径分布情况.实验表明,碳包覆不仅在CoCO₃颗粒表面包覆了一层无定性碳,使得CoCO₃材料在充放电过程中保持结构的稳定性,也形成了一些大约30 nm左右的介孔,这种孔的存在有助于电解液中离子的传输,从而提高材料的电化学性能.电极材料在0.90C(1.00C = 450 mAh•g^-1)倍率下进行循环测试, 500次后的容量仍保持在539 mAh•g^-1,显示出了较好的循环性能.当增加到3.00C倍率时CoCO₃/C容量为130 mAh•g^-1,再恢复到0.15C倍率时容量依然能够达到770 mAh•g^-1,表现出了CoCO₃/C具有良好的稳定性.