TDX—2吸附树脂对低度白酒的除浊,催陈作用

本文介绍了ＴＤＸ－２大孔吸附树选择性地吸附白酒中的三种高级脂肪酸乙酯，而不吸附或极少吸附其他溶质，将酒用泵打入吸附塔，除浊在瞬间完成，流出的酒根据不同产品需要加水降度，理化指无大变化。经树脂处理后白酒质量明显地得到改善，起到催陈作用，缩短陈化才熟期，该工艺已在较大酒厂用于年产万吨粮食低度白酒生产。     

The trapping of indoor air contaminants

The removal of indoor air contaminants by reactivity with air filters coated with reagents has been found to be effective for aldehydes, acidic and basic vapours as well as isocyanates Coatings of polymeric amines were used for formaldehyde trapping as well as for the removal of acidic vapours and for the removal of isocyanates. The addition of glycerol as a plasticizer for the coating can also be an effective reagent.     

Development of a Piezoelectric Crystal Sorption Detector for Monitoring of Total Organic Compounds in Air

Abstract

A light and portable organic vapours monitor has been developed using piezoelectric (P/Z) quartz crystal to determine Volatile Organic Compounds (VOCs) commonly found in workplace air. Out of the eight coating material studied, High Vacuum Grease (HVG) was found to be the best for determining commonly encountered organic vapours such as 1,1,1-Trichloroethane, Chloroform, Benzene and Toluene in room air. The optimised coating weight was 23 μg HVG at a flow rate of 200 mL/min. Moisture was found to interfere and the use of a Nafion gas dryer was found to reduce the relative humidity to a constant 37 % for room air with 43–81 % relative humidity. Under optimised conditions, a mean sensitivity of 1.9 × 1^?2 Hz/ppm was obtained for total VOCs with 17.2% RSD variation towards different VOCs. Excellent linear working ranges were obtained from 40 to 2400 ppm (v/v), with response time and recovery time within one minute up to 500 ppm (v/v) of analyte. High and relatively constant response factors were obtained for different VOCs. The reliability of the mcthod has been established by parallel method comparison using established GC-FID method. The P/Z detector developed could also be used to monitor individual VOCs.     

Dynamic system for the calibration of semi-volatile carbonyl compounds in air

A dynamic calibration system designed for generating accurate and precise concentrations of semi-volatile carbonyls in the ppb (v/v) (ppbv)-ppt (v/v) (pptv) range has been developed and tested. Alkanals from C6 to C9 were used as test compounds. Diffusion rates of their vapours from capillary tubes were determined theoretically and with two methods whose accuracy was independently evaluated with liquid standard solutions. Methods selected for testing the calibration system were those commonly used for the selective quantification of carbonyls in air. One is based on the well-known reaction with 2,4-dinitrophenylhydrazine (DNPH), followed by the analysis of formed hydrazones by HPLC-UV. The other is based on the retention of carbonyls on graphitic carbon adsorbents, followed by MS detection of the sample injected into a capillary column by thermal desorption. A good consistency was found between the values of the diffusion rates determined by the two methods. The scatter between the two methods was in the range of +/-10% when diffusion rates of ca. 1 ng/s were attained. Experimental values closely approached those calculated by applying the equation describing the diffusion of a vapour in equilibrium with the liquid through a capillary tube.     

戊二醛合成跟踪分析

用气相色谱法对液 液相转移反应萃取法合成戊二醛（ＧＡ）反应进行跟踪分析,采用φ３ｍｍ×４ｍ［ｍ（ＳＥ ３０）∶ｍ（硅烷化１０１白色担体）＝１５∶１００］＋φ３ｍｍ×２ｍ［ｍ（ＰＥＧ ２０Ｍ）∶ｍ（硅烷化１０１白色担体）＝１０∶１００］不锈钢柱,双柱双氢焰程序升温,升温程序为７０℃（４ｍｉｎ）１０℃／ｍｉｎ１４０℃（６ｍｉｎ）。Ｎ２４５ｍＬ／ｍｉｎ,Ｈ２６５ｍＬ／ｍｉｎ,空气３００ｍＬ／ｍｉｎ,汽化温度１８５℃,检测温度１８５℃。所建立的方法能较好地分离环戊烯、溶剂、氧化中间产物、ＧＡ、内标、氧化副产物。     

Temperature programmed retention indices: Calculation from isothermal data. Part 2: Results with nonpolar columns

The procedure for calculating linear temperature programmed indices as described in part 1 has been evaluated using five different nonpolar columns, with OV-1 as the stationary phase. For fourty-three different solutes covering five different classes of components, including n-alkanes and alkyl-aromatic compounds, both isothermal and temperature programmed indices were determined. The isothermal information was used to calculate temperature programmed indices. For several linear programmed conditions accuracies better than 0.51^T-units were usually obtained. The results are compared with published procedures. It is demonstrated that isothermal retention information obtained on one column can be transferred to another column with the same stationary phase but different column dimensions and/or phase ratio. The temperature programmed indices calculated in this way also have an accuracy better than 0.51^T-u. The temperature accuracy and precision of the GC-instrumentation used was of the order of 0.1°C. All calculations can be run with a Basic-programmed microcomputer.     

烯丙基乙基醚接枝聚硅氧烷气相色谱固定相的研究

合成了侧链为烯丙基乙基醚的聚硅氧烷气相色谱固定相,静态法涂柱,评价了其色谱性能.该固定相柱效高,易于涂渍,耐温达290℃,分离选择性好,适用于醇类和酯类的分离以及白酒样品的分析.     

高效液相色谱/二极管阵列法快速测定白酒、配制酒与葡萄酒中5种人工合成甜味剂

建立了一种快速检测白酒、配制酒和葡萄酒中安赛蜜、糖精钠、阿斯巴甜、阿力甜及纽甜5种人工合成甜味剂的高效液相色谱分析方法。采用C_(18)柱为分离柱,对流动相的组成和洗脱方式、检测波长等参数进行优化。结果表明,以乙腈和0.02 mol/L硫酸铵(p H 4.4)溶液为流动相,梯度洗脱,柱温40℃,可使5种人工合成甜味剂在15 min内实现基线分离。最佳检测波长下,5种甜味剂在4~200 mg/L浓度范围内呈良好的线性关系,相关系数均大于0.999。样品加标回收率为95.2%~103.2%,相对标准偏差(n=5)均不大于3.4%。该方法简便、快捷、准确、灵敏度较高,适用于白酒、配制酒和葡萄酒等各类酒中5种人工合成甜味剂的快速检测。     

Towards smaller and faster gas chromatography-mass spectrometry systems for field chemical detection

Gas chromatography-mass spectrometry (GC-MS) is already an important laboratory method, but new sampling techniques and column heating approaches will expand and improve its usefulness for detection and identification of unknown chemicals in field settings. In order to demonstrate commercially-available technical advances for both sampling and column heating, we used solid phase microextraction (SPME) sampling of both water and air systems, followed by immediate analysis with a resistively heated analytical column and mass spectrometric detection. High-concern compounds ranging from 140 to 466 amu were analyzed to show the applicability of these techniques to emergency situations impacting public health. A field portable (about 35 kg) GC-MS system was used for analysis of water samples with a resistively heated analytical column externally mounted as a retrofit using the air bath oven of the original instrument design to heat transfer lines. The system used to analyze air samples included a laboratory mass spectrometer with a dedicated resistive column heating arrangement (no legacy air bath column oven). The combined sampling and analysis time was less than 10 min for both air and water sample types. By combining dedicated resistive column heating with smaller mass spectrometry systems designed specificallyfor use in the field, substantially smaller high performance field-portable instrumentation will be possible.     

Separation of elastin cross-links as phenylisothiocyanate derivatives.

A method has been developed for the separation and quantitation of desmosines in tissue samples. The tissue is treated with cold 10% trichloroacetic acid to remove collagen and hydrolysed in HCl vapours in sealed vials. Preseparation of desmosines from tissue acid hydrolysates is performed on a cellulose column, first eluted with n-butanol-acetic acid-water to wash out other amino acids and then with water to recover desmosines. Separated desmosines are then derivatized with phenylisothiocyanate and determined by reversed-phase high-performance liquid chromatography using a gradient system with sodium acetate pH 6.4 and acetonitrile. Desmosines were detected spectrophotometrically at 254 nm. The method was applied to the determination of desmosine in elastin, rat aorta and bovine ligamentum nuchae.     

Polarographic determination of methyl methacrylate

The permanganate oxidation of methyl methacrylate in weakly acidic solution yields methyl pyruvate. Hydroxylamine hydrochloride is used for destroying the excess of permanganate. At the same time it is consumed for oximation of the pyruvate, and the resulting oxime is determined polarographically. The reaction scheme of permanganate oxidation of methyl methacrylate is suggested and optimum working conditions are found both for permanganate oxidation and for polarographic determination. The method is used for the determination of vapours of methyl methacrylate in the air, for industrial hygiene purposes.     

Reproducibility of Programmed-Temperature Retention Indices under Average Linear Velocity Carrier Gas Control of GC and GC�CMS

Programmed-temperature retention indices (PTRIs) are useful for the identification and quantification of chemicals by means of GC and GC/MS. To obtain reproducible PTRIs, we studied the influence of average linear velocity and column length under the constant average linear velocity control (CVC) using 55 pesticides and 33 fatty acid methyl esters. The PTRIs decreased with increasing average linear velocity, and the degree of decrease differs with the compounds. The PTRIs, however, were almost constant as long as the same average linear velocity was used even if the column length was changed. In addition, the correlation between the variation ratio in PTRI and the increase in average linear velocity was linear. Using the linear relationship between PTRIs and average linear velocities under CVC, highly reproducible PTRIs were obtained even if the capillary column length changes. Furthermore, the PTRIs determined by GC with FID, ECD, and FPD under atmospheric pressure were applied to GC/MS under vacuum or vice versa. From these results, it was confirmed that because CVC provides reproducible retention indices, CVC is advantageous for qualitative and quantitative analysis by GC and GC/MS.     

Reliable identification of pesticides using linear retention indices as an active tool in gas chromatographic-mass spectrometric analysis

The present research is focused on the current development and employment of a dedicated pesticide mass spectral library, characterized by a double-filter search procedure: the first is based on the degree of spectral similarity and the second on chromatographic retention information (linear retention indices). The highly pure mass spectra contained in the library have been attained by subjecting mixtures of widely used pesticides to comprehensive GC-MS analysis. Linear retention indices for conventional GC-MS analyses were calculated by injecting the same compounds on a single-column GC-MS system. The effectiveness of this approach was verified by analysing a white wine sample spiked with 10 structurally similar pyrethroid compounds, through automated solid-phase microextraction-GC-MS.     

An all-solid photoelectrochemical cell for the photooxidation of organic vapours under ultraviolet and visible light illumination

An all-solid photoelectrochemical cell has been tested in the photooxidation of methanol vapours as a proof-of-concept for the application of electrochemically enhanced photocatalysis in air treatment. The cell was based on a Nafion^®-impregnated microporous membrane that served as the solid polymer electrolyte. The working and reference electrodes (a TiO₂/WO₃-coated stainless steel mesh and AgCl-coated Ag wire, respectively) were adhered with the addition of a Nafion^® solution onto one face of the membrane, while the counter electrode (a plain stainless steel mesh) was attached to its opposite face. The use of an electrosynthesized TiO₂/WO₃ photoelectrode allowed the utilization of both UV and visible light. The device was tested by constant potential photoamperometry in air streams saturated with water or water–methanol vapours and the obtained photocurrent increased with increasing methanol levels, confirming the photoelectrochemical oxidation of methanol vapours under UV and visible light illumination.     

Discrete microsample injection into a gaseous carrier

Discrete injection (DI) of mul- volume liquid samples into a continuous flow of air as carrier is demonstrated. Atomic-absorption (AA) detection is used. Calibration graphs for zinc, obtained by using the DI-AA-air carrier method have a slope 1.8 times that of graphs obtained by the flow-injection analysis (FIA)-AA-air carrier method. The DI-AA-air carrier signals are higher and sharper than the FIA-AA-water carrier signals, and even exceed the AA steady-state signals for the same zinc solutions, owing to improved nebulization/atomization. The air-carrier method is more rapid than the liquid-carrier method. Measurement rates of 600/hr are possible. The signals show precision comparable to that attainable with water as carrier. The method is particularly useful for flame or plasma detectors and is potentially useful with different gases or vapours as carriers, and for gas-liquid reactions in FIA.     

A splitless Curie point pyrolysis capillary inlet system for use with the adsorption wire technique of vapour analysis

Summary A splitless Curie point pyrolysis inlet system for capillary columns has been built using conventional packed column apparatus. This has enabled the adsorption wire analysis system, for the rapid collection and direct GC analysis of vapours, to be used with capillary columns. Use of the technique for detecting traces of hydrocarbon fuels in arson investigation is described, as are problems occurring in its use.     

染料结合2μm无孔硅胶亲和填料的制备与应用

在２μｍ无孔硅胶表面键合３ 氨丙基 三乙氧基硅烷（ＡＰＳ）,并与三嗪染料活性蓝Ｆ３ＧＡ（ＣｉｂａｃｒｏｎＢｌｕｅＦ３ＧＡ,ＣＢ）反应,制得亲和色谱填料,并采用扫描电镜、元素分析、ｐＨ稳定性测试对此填料进行鉴定与表征。该填料具有良好的色谱性能,且对生物大分子有一定的亲和选择性,改变ｐＨ值及离子强度对溶菌酶的结合量有明显影响,可用于分离卵清蛋白（Ｏｖａｌ）和溶菌酶（Ｌｙｓ）,且对α ,β ,γ 球蛋白有不同的亲和作用,并可从鸡蛋清中制备少量溶菌酶。     

Use of x-ray microtomography to visualise dynamic adsorption of organic vapour and water vapour on activated carbon

X-ray microtomography coupled with image analysis was used to quantify the adsorption of vapours on activated carbon beds. This technique was tested using three different challenges: CCl₄, water vapour and a mixture of water- and organic vapour. It is shown that the used technique allows determining the adsorption front progress in the case of organic vapour and mixture of water and organic vapour whereas the existence of this front was not so obvious in the case of water vapour. Experimental results obtained for organic vapours were interpreted on the basis of the Wheeler-Jonas equation: a good agreement was found between experimental and theoretical breakthrough times.     

An optimized sampling and GC-MS analysis method for benzene in exhaled breath, as a biomarker for occupational exposure

Benzene is known to be toxic and carcinogenic: therefore, in case of exposure to benzene vapours, a reliable biological monitoring procedure is needed, particularly in the field of occupational hygiene. The determination of the concentration of benzene in the exhaled air 8 h after the exposure has been demonstrated to be a significant biomarker, even for low concentrations of airborne benzene vapours. This work presents a sampling and analysis method that optimizes previously described procedures: in the sampling phase, a double-step sample collection in Tedlar bags is used, in order to remove the breath moisture and to standardise the sample volumes. The analytical phase uses a cryogenic trap for the concentration of the air samples to be injected in the GC-MS, without the need for trapping materials, significantly reducing time and costs of the analysis and improving sensitivity. The presented method has been successfully applied to the biological monitoring of a mixed population (occupationally exposed and not exposed subjects, smokers and non-smokers), with a lower detection limit of 1.5 ng of benzene per litre of exhaled air, that is 1/200 of the biological exposure index recommended by the American Conference of Governmental Hygienists.