Organic–inorganic hybrid networks by the sol–gel process and subsequent photopolymerization

Organic–inorganic hybrid materials were prepared by a convenient two‐step curing procedure based on sol–gel condensation and subsequent photopolymerization. Novel bismethacrylate‐based hybrid monomers with pendant, condensable alkoxysilane groups were prepared by Michael addition and possessed number‐average molecular weights between 580 and 1600 g/mol. The formation of inorganic networks by sol–gel condensation of the alkoxysilane groups in the presence of aqueous methacrylic acid was monitored with rheological measurements. The condensation conversion was monitored with solid‐state ²⁹Si cross‐polarization/magic‐angle spinning NMR spectroscopy. Subsequent photopolymerization led to organic–inorganic hybrid networks and low volume shrinkage, ranging from 4.2 to 8.3%, depending on the molecular weight of the hybrid monomer applied. Highly filled composite materials with glass filler fractions greater than 75% showed attractive mechanical properties with Young's moduli of 2700–6200 MPa. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4274–4282, 2001     

Synthesis, structure and bioactivity of pHEMA/SiO2 hybrids derived through in situ sol–gel process

A novel procedure to synthesize poly(2-Hydroxyethylmethacrylate)-silica blend hybrids is presented. Methacrylate monomers bearing an alkoxysilyl unit, prepared by Michael addition of 2-Hydroxyethylmethacrylate (HEMA) to 3-Aminopropyltriethoxysilane (APTS), were employed. By ¹³C NMR and mass analysis it was possible to establish the formation of coupling hybrid species. A hybrid material, with final concentration of 30% w/w of silica gel to the mass of polymer, was obtained through basic catalysed sol–gel process of tetraethoxysilane (TEOS) and the alkoxysilyl unit of the hybrid monomer, followed by in situ free-radical polymerization. Optical transparency and higher glass transition temperature than pHEMA suggest an increase in either density or strong interphase interactions. Moreover, pHEMA/SiO₂ gel blend hybrid exhibits better thermal stability than the as-prepared polymer. Morphology and structure were studied through scanning electron microscopy (SEM), transmission electron spectroscopy (TEM), and dynamic light scattering (DLS). The structure of the hybrid consisted of nanosilica, 10 nm in mean diameter, uniformly dispersed in the pHEMA phase with strong interactions between the phases. Nevertheless, the swelling ratio of the hybrid was comparable to pHEMA. Using FT-IR spectroscopy, SEM and energy dispersive system (EDS), XRD analysis in vitro bioactivity of the hybrid, due to the inorganic phase, was ascertained therefore, the obtained hybrid can be used to make bioactive scaffold for bone engineering.     

Microwave assisted hydroxyalkylamidation of poly(ethylene‐co‐acrylic acid) and formation of grafted poly(ϵ‐caprolactone) side chains

The microwave assisted amidation of poly(ethylene‐co‐acrylic acid) (PEAA) with 2‐(2‐aminoethoxy)ethanol was performed to yield a hydroxy functionalized poly(ethylene) based copolymer (PEAAOH) in a single step. PEAAOH was used as a polyinitiator for the ring‐opening polymerization of ε‐caprolactone. The obtained graft copolymers were studied via ¹H NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry, polarized optical microscopy, and scanning electron microscopy. Microscopy methods show a crystallization behavior of banded spherulites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3659–3667, 2007     

Solid polymer electrolytes. VI. Microstructure of organic–inorganic hybrid networks composed of 3‐glycidoxypropyltrimethoxysilane and LiClO4 and affected by different synthetic routes

Hybrid organic–inorganic materials derived from 3‐glycidoxypropyltrimethoxylsilane were prepared via two different synthetic routes: (1) the HCl‐catalyzed sol–gel approach of silane followed by the lithium perchlorate (LiClO₄)/HCl‐catalyzed opening of epoxide and (2) the simultaneous gelation of tin/LiClO₄‐catalyzed silane/epoxide groups. LiClO₄ catalyzed the epoxide polymerization, and its effects on the structures of these hybrid materials were studied by NMR. The structure of the inorganic side was probed by solid‐state ²⁹Si NMR spectroscopy, and the characterizations of the organic side and the chemical processes involved in the different synthetic routes were performed with solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR. The different synthetic routes significantly affected the polymerization behaviors of the organic and inorganic sides in the presence of LiClO₄. A larger amount of LiClO₄ promoted the opening of epoxide and led to the formation of longer poly(ethylene oxide) chains via the HCl‐catalyzed sol–gel approach, whereas in the case of the tin‐catalyzed approach, the faster polymerization of the inorganic side hindered the growth of the organic network. The addition of LiClO₄ was proven to be without crystalline salt present in the hybrid networks by wide‐angle X‐ray powder diffraction. Also, the interactions between the ions and hybrid host, examined with Fourier transform infrared and ⁷Li proton‐decoupled magic‐angle‐spinning NMR, further demonstrated that extensive ion aggregation existed in these hybrid materials. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 151–161, 2004     

Synthesis and characterization of polytulipalin‐g‐polylactide copolymers

Graft copolymers of poly(tulipalin A) (PT) and poly(DL‐lactide) (PDLLA) (PT‐g‐PDLLA) having various graft lengths and ratios were synthesized by free‐radical copolymerization of α‐methylene‐γ‐butyrolactone (MBL) and PDLLA macromonomers (HEMA‐PDLLA) terminated by 2‐hydroxyethyl methacrylate (HEMA)‐terminated. HEMA‐PDLLA were synthesized by ring opening polymerization (ROP) of DL‐lactide in the presence of HEMA. Both HEMA‐PDLLA and the copolymers were characterized by NMR spectroscopy and gel permeation chromatography (GPC). The thermal properties of the graft copolymers were found to depend on the graft length and the ratio. The copolymers consisting of PDLLA side chains of M_n = 500 Da showed a single T_g between T_gs of the two component polymers, suggesting a miscible state of PT and PDLLA. In contrast, the copolymers consisting of PDLLA side chains of M_n = 1100, 2000, and 7000 Da showed two isolated T_g, suggesting two segregated domains. The AFM phase images of the copolymers supported the single and phase‐separated morphologies for the former and latter systems, respectively. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

FTIR, 13C NMR,and GPC analysis of high‐propylene content co‐ and terpolymers with ethylene and higher α‐olefins synthesized with EtInd2ZrCl2/MAO

This article reports the results of propylene/α‐olefin copolymerization and propylene/ethylene/α‐olefin terpolymerization using low concentrations (less than 5 mol %) of long α‐olefins such as 1‐octene, 1‐decene, and 1‐dodecene. Kinetics data are presented and discussed. The highest activity was found with the longest α‐olefin studied (1‐dodecene). A possible explanation is proposed for this and other characteristics of the polymers obtained. The effect of low‐ethylene contents (4 mol % in the gas phase) on the copolymerization of propylene/α‐olefins was also examined. The polymers synthesized were characterized by ¹³C NMR, gel permeation chromatography, DSC, Fourier transform infrared spectroscopy, and wide‐angle X‐ray scattering. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2005–2018, 2001     

Poly(ethylene terephthalate) copolymers containing 5‐nitroisophthalic units. II. Crystallization studies

The microstructure and crystallization behavior of a set of poly(ethylene terephthalate‐co‐5‐nitroisophthalate) copolymers (PETNI) containing 5‐nitroisophthalic units in the 10–50 mol % range were examined and compared to those of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐isophthalate) (PETI) copolymers. A ¹³C NMR analysis of PETNI copolymers in a trifluoroacetic acid solution indicates that they are random copolymers with average sequence lengths in accordance with ideal polycondensation statistics. Differential scanning calorimetry (DSC) studies show that PETNI containing 5‐nitroisophthalic units up to 20 mol % are able to crystallize and that crystallization takes place in these copolymers at much slower rates than in PET. Wide‐angle X‐ray diffraction from powder and fibers reveals that crystallizable PETNI adopts the same triclinic crystal structure as PET, with the nitroisophthalate units being excluded from crystallites. Fourier transform infrared in combination with cross‐polarization/magic‐angle spinning ¹³C NMR spectroscopy demonstrates the occurrence of a gauche–trans conversion encompassing the crystallization process. A correlation between DSC and spectroscopic data leads us to conclude that the content of trans conformer in the noncrystallized phase of PETNI is higher than in both PET and PETI copolymers and suggests that secondary crystallization in the homopolymer must proceed by a mechanism different than that in copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1553–1564, 2001     

Molecular motion in nanocomposites of poly(ethylene oxide) and montmorillonite

Motion of chains of poly(ethylene oxide) within the interlayer spacing of 2:1 phyllosilicate/montmorillonite was studied with ¹H and ¹³C NMR spectroscopy. Measurements of the ¹H NMR line widths and relaxation times across a large temperature range were used to determine the effect of bulk thermal transitions on polymer chain motion within the nanocomposites. The results were consistent with previous reports of low apparent activation energies of motion. Details of the frequency and geometry of motion were obtained from a comparison of the ¹³C cross‐polarity/magic‐angle spinning spectra and relaxation times of the nanocomposite with those of the pure polymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1678–1685, 2001     

Amphiphilic conetworks. IV. Poly(methacrylic acid)‐l‐polyisobutylene and poly(acrylic acid)‐l‐polyisobutylene based hydrogels prepared by two‐step polymer procedure. New pH responsive conetworks

This article describes the synthesis and characterization of new amphiphilic polymer conetworks containing hydrophilic poly(methacrylic acid) (PMAA) or poly(acrylic acid) (PAA) and hydrophobic polyisobutylene (PIB) chains. These conetworks were prepared by a two‐step polymer synthesis. In the first step, a cationic copolymer of isobutylene (IB) and 3‐isopropenyl‐α,α‐dimethylbenzyl isocyanate (IDI) was prepared. The isocyanate groups of the IB–IDI random copolymer were subsequently transformed in situ to methacrylate (MA) groups in reaction with 2‐hydroxyethyl methacrylate (HEMA). In the second step, the resulting MA‐multifunctional PIB‐based crosslinker, PIB(MA)_n, with an average functionality of approximately four methacrylic groups per chain, was copolymerized with methacrylic acid (MAA) or acrylic acid (AA) by radical mechanism in tetrahydrofuran giving rise to amphiphilic conetworks containing 31–79 mol % of MAA or 26–36 mol % of AA. The synthesized conetworks were characterized with solid‐state ¹³C‐NMR spectroscopy and differential scanning calorimetry. The amphiphilic nature of the conetworks was proven by swelling in both aqueous media with low and high pH and n‐heptane. The effect of varying pH on the swelling behavior of the synthesized conetworks is presented. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1284–1291, 2009     

In situ polymerization of silicic acid in polyethylene–octene elastomer: Properties and characterization of the hybrid nanocomposites

Silicic acid produced from sodium metasilicate hydrate and metallocene polyethylene–octene elastomer (POE) were chosen as the ceramic precursor and the continuous phase, respectively, for preparation of new hybrids by an in situ sol–gel process. To obtain a better hybrid, the acrylic acid‐grafted polyethylene–octene elastomer (POE‐g‐AA) prepared in our laboratory and used as the continuous phase was also investigated. Characterizations of POE/SiO₂ and POE‐g‐AA/SiO₂ composites were performed by Fourier transform infrared spectroscopy, ²⁹Si solid‐state nuclear magnetic resonance (NMR) spectrometry, X‐ray diffractometry, differential scanning calorimetry, thermogravimetry analysis, and an Instron mechanical tester. The POE‐g‐AA/SiO₂ hybrid could give the positive effect on the properties of POE/SiO₂ hybrid because the carboxylic acid groups of acrylic acid should act as coordination sites for the silica phase to form chemical bonds. The result of ²⁹Si solid‐state NMR spectra showed that Si atom coordination around SiO₄ units is predominantly Q₃ and Q₄. Also, the POE‐g‐AA/SiO₂ hybrid with 15 wt % SiO₂ gave the maximum values of tensile strength and glass‐transition temperature because excess particles might cause the separation between the organic and inorganic phases when the silica content was beyond this point. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 351–359, 2003     

Interaction of silicic acid with poly(1‐vinylimidazole)

Poly(1‐vinylimidazole) reacts with silicic acid and poly(silicic acid), giving rise to water‐soluble complexes and insoluble composites because of hydrogen bonding. The composition, structure, and morphology of the obtained products have been studied with elemental analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy. The main direction of the reaction depends not only on the initial ratio of the components, concentration, and pH but also on the sequence of the reagent mixing: the presence of poly(1‐vinylimidazole) macromolecules during the formation of silicic acid stabilizes soluble complexes, which precipitate with an excess of H₄SiO₄ only. These soluble complexes may serve as a pattern of particles responsible for the transport of silicic acid in diatom algae and other organisms that assimilate silicon from the environment. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 820–827, 2006     

Living polymerization of D,L‐3‐methylglycolide initiated with bimetallic (Al/Zn) μ‐oxo alkoxide and copolymers thereof

D,L ‐3‐Methylglycolide (MG) was successfully polymerized with bimetallic (Al/Zn) μ‐oxo alkoxide as an initiator in toluene at 90 °C. The effect of the initiator concentration and monomer conversion on the molecular weight was studied. It is shown that the polymerization of MG follows a living process. A kinetic study indicated that the polymerization approximates the first order in the monomer, and no induction period was observed. ¹H NMR spectroscopy showed that the ring‐opening polymerization proceeds through a coordination–insertion mechanism with selective cleavage of the acyl–oxygen bond of the monomer. On the basis of ¹H NMR and ¹³C NMR analyses, the selective cleavage of the acyl–oxygen bond of the monomer mainly occurs at the least hindered carbonyl groups (P₁ = 0.84, P₂ = 0.16). Therefore, the main chain of poly(D,L ‐lactic acid‐co‐glycolic acid) (50/50 molar ratio) obtained from the homopolymerization of MG was primarily composed of alternating lactyl and glycolyl units. The diblock copolymers poly(ϵ‐caprolactone)‐b‐poly(D,L ‐lactic acid‐alt‐glycolic acid) and poly(L ‐lactide)‐b‐poly(D,L ‐lactic acid‐alt‐glycolic acid) were successfully synthesized by the sequential living polymerization of related lactones (ϵ‐caprolactone or L ‐lactide). ¹³C NMR spectra of diblock copolymers clearly show their pure diblock structures. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 357–367, 2001     

Regioselective and stereoselective alternating copolymerization of carbon monoxide with functional olefins

Enantioselective, alternating copolymerizations of carbon monoxide with ω‐undecylenic acid, ethyl acrylate, and butyl acrylate were carried out for the first time with a palladium catalyst modified by 1,4:3,6‐dianhydro‐2,5‐dideoxy‐2,5‐bis(diphenylphosphino)‐L ‐iditol. Optical rotation, elemental analysis, and ¹H NMR,¹³C NMR, and IR spectra showed that the copolymers were optically active, isotactic, alternating poly(1,4‐ketone) or poly(spiroketal) structures. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2027–2036, 2001     

Thermoreversible gelation of poly(ethylene oxide) biodegradable polyester block copolymers. II

Poly(ethylene oxide)-b-poly(L-lactic acid) (PEO-PLLA) diblock copolymers were synthesized via a ring opening polymerization from poly(ethylene oxide) and l -lactide. Stannous octoate was used as a catalyst in a solution polymerization with toluene as the solvent. Their physicochemical properties were investigated by using infrared spectroscopy, ¹H-NMR spectroscopy, gel permeation chromatography, and differential scanning calorimetry, as well as the observational data of gel-sol transitions in aqueous solutions. Aqueous solutions of PEO-PLLA diblock copolymers changed from a gel phase to a sol phase with increasing temperature when their polymer concentrations are above a critical gel concentration. As the PLLA block length increased, the gel-sol transition temperature increased. For comparison, diblock copolymers of poly(ethylene oxide)-b-poly(l -lactic acid-co-glycolic acid) [PEO-P(LLA/GA)] and poly(ethylene oxide)-b-poly(dl -lactic acid-co-glycolic acid) [PEO-P(DLLA/GA)] were synthesized by the same methods, and their gel-sol transition behaviors were also investigated. The gel-sol transition properties of these diblock copolymers are influenced by the hydrophilic/hydrophobic balance of the copolymer, block length, hydrophobicity, and stereoregularity of the hydrophobic block of the copolymer. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2207–2218, 1999     

Dihydrophilic block copolymers with ionic and nonionic blocks. I. Poly(ethylene oxide)‐b‐polyglycidol with OP(O)(OH)2, COOH,or SO3H functions: Synthesis and influence for CaCO3 crystallization

Dihydrophilic block copolymers of poly(ethylene oxide)‐b‐polyglycidol were prepared and polyglycidol blocks converted into ionic blocks containing  OP(O)(OH)₂,  COOH, or  SO₃H groups. Although phosphorylation of polyhydroxy compounds with POCl₃ usually leads to insoluble products, phosphorylation of poly(ethylene oxide)‐b‐polyglycidol using a POCl₃/ OH ratio equal to 1/1 gave soluble products, predominantly monoester of phosphoric acid (after hydrolysis) (provided that the reaction was conducted in triethyl phosphate as solvent). All copolymers were characterized by ¹H NMR, ¹³C NMR, and/or ³¹P NMR spectra for confirming their structure. The degree of substitution was determined from quantitative ¹³C NMR spectroscopy (inverted‐gate decoupling‐acquisition mode). Preliminary results indicate that from these three groups of block copolymers the phosphoric acid esters are the most effective ones at least in controlling the growth of CaCO₃ crystals in aqueous solution. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 955–963, 2001     

Self‐assembly of star‐shaped polystyrene‐block‐polypeptide copolymers synthesized by the combination of atom transfer radical polymerization and ring‐opening living polymerization of α‐amino acid‐N‐carboxyanhydrides

The self‐assembling nature and phase‐transition behavior of a novel class of triarm, star‐shaped polymer–peptide block copolymers synthesized by the combination of atom transfer radical polymerization and living ring‐opening polymerization of α‐amino acid‐N‐carboxyanhydride are demonstrated. The two‐step synthesis strategy adopted here allows incorporating polypeptides into the usual synthetic polymers via an amido–amidate nickelacycle intermediate, which is used as the macroinitiator for the growth of poly(γ‐benzyl‐L ‐glutamate). The characterization data are reported from analyses using gel permeation chromatography and infrared, ¹H NMR, and ¹³C NMR spectroscopy. This synthetic scheme grants a facile way to prepare a wide range of polymer–peptide architectures with perfect microstructure control, preventing the formation of homopolypeptide contaminants. Studies regarding the supramolecular organization and phase‐transition behavior of this class of polymer‐block‐polypeptide copolymers have been accomplished with X‐ray diffraction, infrared spectroscopy, and thermal analyses. The conformational change of the peptide segment in the block copolymer has been investigated with variable‐temperature infrared spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2774–2783, 2006     

Synthesis and properties of oxygen‐, methylene‐, and alkylene‐bridged poly(dithiafulvene)s

Polymerization by cycloaddition between aldothioketene and its alkynethiol tautomer (derived in situ from a diyne) leading to the formation of dithiafulvene unit‐linked polymers has been studied. Two aromatic diynes [bis(4‐ethynyldiphenyl)methane ( 1a ) and 4,4′‐diethynyldiphenyl ether) ( 1b )] were used as starting materials with the aim of obtaining non‐π‐conjugated methylene‐ and oxygen‐bridged aromatic poly(dithiafulvene)s. The poly(dithiafulvene) derived from bis(4‐ethynyldiphenyl)methane can be considered as an interesting precursor to a small band‐gap polymer having alternating aromatic and quinonoid moieties. Further, two aliphatic diynes [1,7‐octadiyne ( 3a ) and 1,9‐decadiyne ( 3b )] were subjected to cycloaddition polymerization to obtain aliphatic poly(dithiafulvene)s containing localized electron‐rich dithiafulvene units. The polymers obtained were characterized by IR, ¹H NMR, gel permeation chromatography, and cyclic voltammetry. The electron‐donating property of the polymers was evident from the charge‐transfer (CT) complex formation with an electron acceptor 7,7,8,8‐teracyanoquinodimethane. The CT complexes were characterized by IR, ¹H NMR, and ultraviolet–visible spectroscopies. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3593–3603, 2001     

New segmented poly(ester‐urethane)s from renewable resources

The physical and mechanical properties of aliphatic homopolyesters from monomers obtainable from renewable resources, namely, 1,3‐propanediol and succinic acid, were improved by their combination with aromatic urethane segments capable of establishing strong intermolecular hydrogen bonds. Segmented poly(ester‐urethane)s were synthesized from dihydroxy‐terminated oligo(propylene succinate)s chain‐extended with 4,4′‐diisophenylmethane diisocyanate. The newly synthesized materials were exhaustively characterized by ¹H NMR spectroscopy, size exclusion chromatography, differential scanning calorimetry, dynamic mechanical analysis, and with respect to their main static mechanical properties, an Instron apparatus was used. The average repeat number of the hard segments, evaluated by NMR, ranged from 4 to 9, whereas that of the flexible segments was about 14. The degree of crystallinity, glass‐transition temperature, melting point, tensile strength, elongation, and Young's modulus were influenced by the ratio between hard and soft segments of the segmented copolymer in a predictable way. The results demonstrated that poly(ester‐urethane)s from 1,3‐propanediol and succinic acid are promising thermoplastics. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 630–639, 2001     

Influence of gel composition on the solubility parameter of poly(2‐hydroxyethyl methacrylate‐itaconic acid) hydrogels

The solubility parameters of pure poly(2‐hydroxyethyl methacrylate) (PHEMA) and poly(2‐hydroxyethyl methacrylate/itaconic acid) [P(HEMA/IA)] hydrogels were determined by 20 solvents with various solubility parameters in swelling experiments. The solubility parameter of pure PHEMA was 26.93 ± 0.46 (MPa)^1/2. The effect of mole percentages of itaconic acid (IA) in P(HEMA/IA) hydrogels on the solubility parameter was investigated. The measured values were compared to literature and solubility values theoretically determined by group contribution values of van Krevelen and Hoy. The incorporation of IA into the hydrogel system slightly increased the solubility parameter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1995–2003, 2002