Studies on epoxy resins cured by cationic latent thermal catalysts: The effect of the catalysts on the thermal,rheological, and mechanical properties

To investigate the effect of catalysts on the thermal, rheological, and mechanical properties of an epoxy system, a resin based on diglycidyl ether of bisphenol‐A (DGEBA) was cured by two cationic latent thermal catalysts, N‐benzylpyrazinium hexafluoroantimonate (BPH) and N‐benzylquinoxalinium hexafluoroantimonate (BQH). Differential scanning calorimetry was used for the thermal characterization of the epoxy systems. Near‐infrared spectroscopy was employed to examine the cure reaction between the DGEBA and the latent thermal catalysts used. The rheological properties of the blend systems were investigated under an isothermal condition with a rheometer. To characterize the mechanical properties of the systems, flexure, fracture toughness (K_IC), and impact tests were performed. The phase morphology was studied with scanning electron microscopy of the fractured surfaces of mechanical test samples. The conversion and cure activation energy of the DGEBA/BQH system were higher than those of the DGEBA/BPH system. The crosslinking activation energy showed a result similar to that obtained from the cure kinetics of the blend systems. The flexure strength, K_IC, and impact properties of the DGEBA/BQH system were also superior to those of the DGEBA/BPH system. This was a result of the substituted benzene group of the BQH catalyst, which increased the crosslink density and structural stability of the epoxy system studied. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 187–195, 2001     

Cure behavior of diglycidylether of bisphenol A/trimethylolpropane triglycidylether epoxy blends initiated by thermal latent catalyst

Cure behaviors of diglycidylether of bisphenol A (DGEBA)/trimethylolpropane triglycidylether (TMP) epoxy blends initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate (BPH) as a cationic latent catalyst were investigated using DSC and rheometer. This system showed more than one type of reaction and BPH could be excellent thermal latent catalyst without any co‐initiator. The cure activation energy (E_a) obtained from Kissinger method using dynamic DSC data was higher in DGEBA/TMP mixtures than in pure DGEBA. Rheological properties of the blend system were investigated under isothermal condition using a rheometer. The gel time was obtained from the analysis of storage modulus (G′), loss modulus (G″) and damping factor (tanδ). The crosslinking activation energy (E_c) was also determined from the Arrhenius equation based on the gel time and curing temperature. As a result, the crosslinking activation energy showed a similar behavior with that obtained from Kissinger method. And the gel time decreased with increasing TMP content, which could be resulted from increasing the activated sites by trifunctional epoxide groups and decreasing the viscosity of DGEBA/TMP epoxy blend in the presence of TMP. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2114–2123, 2000     

Isothermal cure kinetics of epoxy/phenol‐novolac resin blend system initiated by cationic latent thermal catalyst

The investigation of the cure kinetics of a diglycidyl ether of bisphenol A (DGEBA)/phenol‐novolac blend system with different phenolic contents initiated by a cationic latent thermal catalyst [N‐benzylpyrazinium hexafluoroantimonate (BPH)] was performed by means of the analysis of isothermal experiments using a differential scanning calorimetry (DSC). Latent properties were investigated by measuring the conversion as a function of curing temperature using a dynamic DSC method. The results indicated that the BPH in this system for cure is a significant thermal latent initiator and has good latent thermal properties. The cure reaction of the blend system using BPH as a curing agent was strongly dependent on the cure temperature and proceeded through an autocatalytic kinetic mechanism that was accelerated by the hydroxyl group produced through the reaction between DGEBA and BPH. At a specific conversion region, once vitrification took place, the cure reaction of the epoxy/phenol‐novolac/BPH blend system was controlled by a diffusion‐control cure reaction rather than by an autocatalytic reaction. The kinetic constants k₁ and k₂ and the cure activation energies E₁ and E₂ obtained by the Arrhenius temperature dependence equation of the epoxy/phenol‐novolac/BPH blend system were mainly discussed as increasing the content of the phenol‐novolac resin to the epoxy neat resin. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2945–2956, 2000     

Effect of the substituted benzene group on thermal and mechanical properties of epoxy resins initiated by cationic latent catalysts

Epoxy resins (DGEBA) were cured by cationic latent thermal catalysts, that is, N‐benzylpyrazinium hexafluoroantimonate (BPH) and N‐benzylquinoxalinium hexafluoroantimonate (BQH) to investigate the effect of substituted benzene group on cure kinetics and mechanical properties of epoxy system. Differential scanning calorimetry (DSC) was undertaken for activation energy of the system. It was also characterized in terms of flexural, fracture toughness, and Izod impact strengths for the mechanical tests. As a result, the cure reaction of both epoxy systems resulted in an autocatalytic kinetic mechanism accelerated by hydroxyl groups. Also, the conversion and cure activation energy of the DGEBA/BQH system were higher than those of DGEBA/BPH system. The mechanical properties of the DGEBA/BQH system were also superior to those of the DGEBA/BPH system, as well as the morphology. This was probably due to the consequence of the effect of the substituted benzene group of the BQH catalyst, resulting in increasing the crosslinking density and structural stability in the epoxy system studied. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2419–2429, 2004     

Near‐infrared spectroscopic studies on the cure behaviors of the CAE/DGEBA blend system initiated by a thermal latent catalyst

The latent properties and cure behaviors of an epoxy blend system based on cycloaliphatic epoxy (CAE) and diglycidyl ether of bisphenol A (DGEBA) epoxy containing N‐benzylpyrazinium hexafluoroantimonate (BPH) as a thermal latent initiator were investigated with near‐infrared (N‐IR) spectroscopy. The assignments of the latent properties and cure kinetics were performed by the measurements of the N‐IR reflectance for epoxide and hydroxyl functional groups at different temperatures and compositions. As a result, this system showed more than one type of reaction, and BPH was an excellent thermal latent catalyst without any coinitiator. The cure behaviors were identified by the changes in the absorption intensity of the hydroxyl groups at 7100 cm⁻¹ with different composition ratios. Moreover, characteristic N‐IR band assignments were used to evaluate the reactive kinetics and were shown to be an appropriate method for studying the cure behaviors of the CAE/DGEBA blend system containing a thermal latent catalyst. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 326–331, 2001     

Thermal stability and toughening of epoxy resin with polysulfone resin

The cure behavior, thermal stability, and mechanical properties of diglycidylether of bisphenol A (DGEBA)/polysulfone (PSF) blends initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate as a cationic latent catalyst were investigated. The DGEBA/PSF content was varied within 100/0–100/40 wt %. Latent properties were studied through the measurement of the conversion as a function of the curing temperature, and the cure activation energy (E_a) was studied by the Kissinger method with a dynamic differential scanning calorimetry analysis. The thermal stabilities, largely based on the integral procedural decomposition temperature (IPDT) and decomposed activation energy (E_t), were investigated by the measurement of thermogravimetric analysis. For the mechanical properties of the casting specimens, the critical stress intensity factor (K_IC) test was performed, and their fractured surfaces were examined with scanning electron microscopy. E_a, IPDT, E_t, and K_IC increased with PSF increasing in the neat epoxy resin up to 30 wt %. However, there was a marginal decrease in the blend system in both the thermal and mechanical properties due to the phase separation between DGEBA and PSF. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 121–128, 2001     

N,N‐dimethylaminopyridine as initiator in the copolymerization of diglycidylether of bisphenol A with six‐membered cyclic carbonates

N,N‐Dimethylaminopyridine (DMAP) was used as initiator to cure mixtures of diglycidylether of bisphenol A (DGEBA) and 1,3‐dioxan‐2‐one (TMC) or 5,5‐dimethyl‐1,3‐dioxan‐2‐one (DMTMC). The curing was studied by differential scanning calorimetry (DSC) and Fourier transform infrared in the attenuated‐total‐reflection mode (FTIR/ATR). FTIR/ATR was used to monitor the competitive reactive processes and to quantify the evolution of the groups involved in the curing. We observed the formation of five‐membered cyclic carbonates and anionic carbonate groups that remain unreacted at the chain ends. The formation of these groups was explained by the attack of the anionic propagation species on the methylene carbon of the carbonate group, which leads to an alkyl‐oxygen rupture. By performing the cure in the thermobalance we could evaluate the loss of CO₂ produced in the samples containing carbonates. The kinetics were studied by DSC and analyzed with isoconversional procedures. The addition of carbonates slows down the curing rate. Thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA) experiments were used to evaluate the properties of the materials obtained. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2873–2882, 2006     

New,strong cationic hydrogels: Preparation of N,N,N′,N′‐tetraallyl piperazinium dibromide and its copolymers with N,N‐diallyl morpholinium bromide

N,N,N′,N′‐tetraallyl piperazinium dibromide (TAP) has been prepared in high yields by quaternization of N,N′‐diallyl piperazine with allyl bromide. Herein, we have described preparation of nonhydrolysable, strong, cationic hydrogels by copolymerization of TAP with N,N‐diallyl morpholinium bromide (DAM) in the presence of t‐butyl hydroperoxide as initiator in aqueous solutions. Because the monomer and crosslinker involved consist of quaternary amine functions, these hydrogels are fully cationic and do not carry hydrolysable groups. Contrary to expectations, the quaternary amine hydrogels presented do not show any super absorbency, instead dry gel particles in water undergo spontaneous disintegration with an audible bursting of the particles due to instantaneous, high osmotic pressure. Whereas, in KBr or HBr solutions, the swellings are relatively slow. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1006–1013, 2000     

Viscoelastic properties of decrosslinked irradiation‐crosslinked polyethylenes in supercritical methanol

The viscoelastic properties of decrosslinked irradiation‐crosslinked polyethylenes using a supercritical methanol were investigated via oscillatory dynamic shear measurements. Decrosslinked polymers at a low reaction temperature exhibited solid‐like rheological properties, as evidenced by a small slope at G′ and G″, a long relaxation time, slow stress relaxation behavior, and considerable yield stress. In contrast, decrosslinked polymers at a high temperature exhibited liquid‐like rheological properties that included a large slope in G′ and G″, a short relaxation time, fast stress relaxation behavior, and nonyield stress. The difference in the viscoelastic properties of the decrosslinked polyethylenes was attributed to the difference in the gel content with the reaction temperature. A higher gel content induced stronger solid‐like viscoelastic properties. Hence, the rheological measurements were useful for analyzing the molecular structure of decrosslinked polymers using a supercritical fluid. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1265–1270, 2010     

Atom transfer radical polymerization of N‐vinyl carbazole: Optimization to characterization

The homopolymerization of N‐vinylcarbazole was performed with atom transfer radical polymerization (ATRP) with Cu(I)/Cu(II)/2,2′‐bipyridine (bpy) as the catalyst system at 90 °C in toluene. N‐2‐Bromoethyl carbazole was used as the initiator, and the optimized ratio of Cu(I) to Cu(II) was found to be 1/0.3. The resulting homopolymer, poly(N‐vinylcarbazole) (PVK), was formed after a monomer conversion of 76% in 20 h. The molecular weight as well as the polydispersity index (PDI) showed a linear relation with the conversion, which showed control over the polymerization. A semilogarithmic plot of the monomer conversion with time was linear, indicating the presence of constant active species throughout the polymerization. The initiator efficiency and the effect of the variation of the initiator concentration on the polymerization were studied. The effects of the addition of CuBr₂, the variation of the catalyst concentration with respect to the initiator, and CuX (X = Br or Cl) on the kinetics of homopolymerization were determined. With Cu(0)/CuBr₂/bpy as the catalyst, faster polymerization was observed. For a chain‐extension experiments, PVK (number‐average molecular weight = 1900; PDI = 1.24) was used as a macroinitiator for the ATRP of methyl methacrylate, and this resulted in the formation of a block copolymer that gave a monomodal curve in gel permeation chromatography. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1745–1757, 2006     

Copolymer networks from carboxyl‐containing polyaryletherketone and diglycidyl ether of bisphenol‐A: Preparation and properties

This article presents a new type of epoxy‐toughening system, in which high‐T_g polyaryletherketone (PEK‐L) containing one carboxyl group per repeating unit was utilized to randomly copolymerize with epoxy resin (DGEBA) to form crosslinking network. Compared to the neat epoxy resin, the PEK‐L/DGEBA copolymers showed simultaneous enhancement in flexural strains at break by 282%, G_IC value by 193%, and flexural strength by 14%. The reason was attributed to the uniform three‐dimensional copolymer network interweaved by PEK‐L and DGEBA segments through strong covalent bonds. The copolymerization process were monitored and examined by FTIR spectra. The effect of copolymer composition on the thermal and mechanical properties as well as toughening mechanism were also investigated and discussed in detail. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Rheological and mechanical properties of epoxy/polyurethane blends initiated by N‐benzylpyrazinium hexafluoroantimonate salt

In this work the cure behavior and rheological and mechanical interfacial properties of the diglycidylether of bisphenol A (DGEBA)/polyurethane (PU) blend system, initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate as a latent thermal catalyst, were investigated. To characterize the mechanical interfacial properties of the system, the critical stress intensity factor (K_IC) was calculated with a single‐edge‐notched beam (SEN) beam fracture toughness test. And an impact test was performed at room and cryogenic temperatures to determine the performance of PU at room and low‐temperatures, respectively. As a result, the E_c of the blend system was increased with increasing PU content, showing a maximum value at 30 wt % PU, which was in good agreement with the mechanical properties of the blend system. Consequently, these results could be explained by the improvement that occurred in intermolecular hydrogen bonding between the hydroxyl group in EP and the isocyanate group in PU, resulting in increased compatibility of the components within the interpenetrating polymer networks. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3841–3848, 2004     

Isoconversional method to explore the cure reaction mechanisms and curing kinetics of DGEBA/EMI‐2,4/nano‐SiC system

The curing kinetics of the diglycidyl ether of bisphenol‐A (DGEBA)/2‐ethyl‐4‐methylimidazole (EMI‐2,4)/nano‐sized carborundum (nano‐SiC) system was studied by means of nonisothermal differential scanning calorimetry (DSC). An isoconversional method of kinetic analysis yields a dependence of the effective activation energy E on the extent of conversion that decreases initially, and then increases as the cure reaction proceeds. The variations of E were used to study the cure reaction mechanisms, and the Shrinking Core Model was used to study the resin–particle reaction. The results show that the presence of nano‐SiC particles prevents the occurrence of vitrification, as well as inhibits the cure reaction. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 371–379, 2006     

Curing of linear and crosslinked epoxy systems: A fluorescence study with dansyl derivatives

The curing of diglycidyl ether of bisphenol A (DGEBA) with N,N′-dimethylethylenediamine (N,N′-DMEDA) or ethylenediamine (EDA) was monitored by fluorescence spectroscopy and Fourier transform infrared (in the near-infrared region). 5-Dimethylamino-naphthalene-1-sulfonamide (DNS) derivatives were used as probes (fluorophores added to the reaction mixture) and labels (fluorophores attached by covalent bonds to diglycidyl reactants). The term containing the ratio of the reaction rate constants for the addition of the secondary and primary amine hydrogens to the epoxide was included in the reduced reaction rate term for the autocatalyzed and catalyzed epoxide curing reactions. The changes in the integrated fluorescence intensities of the labels during the epoxy group conversion indicated, in some cases, the most important changes in the chemical transformations of the reaction mixture: the epoxy group conversion, during which a rapid increase in the tertiary amino group concentration was first observed; the gel point (for EDA); and the entry of the system into the glassy state (for N,N′-DMEDA and EDA). The fluorescence probes monitored neither the gel point nor the threshold of the glassy state. For the DGEBA–N,N′-DMEDA system, a wavy dependence of the integrated fluorescence intensities of the DNS labels on the epoxy group conversion might reflect the molar concentrations of polymer homologues (referred to the initial number of moles in the system) in the reaction mixtures of the diepoxide and secondary diamine. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 64–78, 2004     

Synthesis of ultrahigh molecular weight poly(N‐vinylcarbazole) with a high yield using low‐temperature heterogeneous‐solution polymerization

To prepare ultrahigh molecular weight (UHMW) poly(N‐vinylcarbazole) (PVCZ) with a high conversion, I heterogeneous‐solution‐polymerized N‐vinylcarbazole (VCZ) in methanol/tertiary butyl alcohol (TBA) at 25, 35, and 45 °C with a low‐temperature initiator, 2,2′‐azobis(2,4‐dimethylvaleronitrile) (ADMVN), and I investigated the effects of the polymerization conditions on the polymerization behavior and molecular parameters of PVCZ. A low‐polymerization temperature with ADMVN, a heterogeneous system with methanol, and a low chain transfer with TBA proved to be successful in obtaining PVCZ of UHMW [weight‐average molecular weight (M_w) > 3,000,000] and high conversion (>80%) with a smaller temperature rise during polymerization but still of free‐radical polymerization by an azoinitiator. The polymerization rate of VCZ in methanol/TBA at 25 °C was proportional to the 0.97 power of the ADMVN concentration, indicating a heterogeneous nature for the polymerization. The molecular weight was higher and the molecular weight distribution was narrower with PVCZ polymerized at lower temperatures. For PVCZ produced in methanol/TBA at 25 °C with an ADMVN concentration of 0.0001 mol/mol of VCZ, an M_w of 3,230,000 was obtained, with a polydispersity index of 2.4. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 539–545, 2001     

Synthesis of poly(tetrahydrofuran)‐b‐polystyrene block copolymers from dual initiators for cationic ring‐opening polymerization and atom transfer radical polymerization

A dual initiator (4‐hydroxy‐butyl‐2‐bromoisobutyrate), that is, a molecule containing two functional groups capable of initiating two polymerizations occurring by different mechanisms, has been prepared. It has been used for the sequential two‐step synthesis of well‐defined block copolymers of polystyrene (PS) and poly(tetrahydrofuran) (PTHF) by atom transfer radical polymerization (ATRP) and cationic ring‐opening polymerization (CROP). This dual initiator contains a bromoisobutyrate group, which is an efficient initiator for the ATRP of styrene in combination with the Cu(0)/Cu(II)/N,N,N′,N″,N″‐pentamethyldiethylenetriamine catalyst system. In this way, PS with hydroxyl groups (PS‐OH) is formed. The in situ reaction of the hydroxyl groups originating from the dual initiator with trifluoromethane sulfonic anhydride gives a triflate ester initiating group for the CROP of tetrahydrofuran (THF), leading to PTHF with a tertiary bromide end group (PTHF‐Br). PS‐OH and PTHF‐Br homopolymers have been applied as macroinitiators for the CROP of THF and the ATRP of styrene, respectively. PS‐OH, used as a macroinitiator, results in a mixture of the block copolymer and remaining macroinitiator. With PTHF‐Br as a macroinitiator for the ATRP of styrene, well‐defined PTHF‐b‐PS block copolymers can be prepared. The efficiency of PS‐OH or PTHF‐Br as a macroinitiator has been investigated with matrix‐assisted laser desorption/ionization time‐of‐flight spectroscopy, gel permeation chromatography, and NMR. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3206–3217, 2003     

Metal‐template synthesis of cyclic epoxide–amine oligomers: Uncrosslinked epoxide–amine addition polymers, 47

The addition reaction of 2,2‐bis‐[4‐(2,3‐epoxypropoxy)‐phenyl]‐propane (DGEBA) and preformed complexes of metal ions and disecondary diamines led to a large quantity of cyclic epoxide–amine oligomers. As shown by gel permeation chromatographic analysis, cycles of n = 1, 2, and 3 were formed. Functional epoxide end groups of the prepared oligomers were completely missing in the IR and ¹H NMR and ¹³C NMR spectra. In the fast atom bombardment and matrix‐assisted laser desorption/ionization mass spectra, the molecular ions of the n = 1, 2, 3 cycles of DGEBA and N,N′‐dibenzyl‐5‐oxanonanediamine‐1,9 were detected at m/z = 680, 1361, and 2042. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2047–2052, 2003     

Supramolecular polymer gels formed from carboxy‐terminated telechelic polybutadiene and polyamidine through amidinium‐carboxylate salt bridge

In this article, we report the preparation and properties of the bulk supramolecular polymer gels prepared from a polybutadiene based on the amidinium‐carboxylate salt bridge, highlighting the difference from a well‐established network system based on carboxylic acid and amine. We have prepared the amidinium‐carboxylate salt bridge‐based supramolecular polymer gels from a carboxy‐terminated telechelic polybutadiene and a linear polyamidine having N,N′‐di‐substituted acetamidine group in the main chain. FTIR analysis along with Small angle X‐ray scattering measurements indicated that the salt bridge was attributed to the gelation through three‐dimensional network formation. Virtually no fluidity was observed for the supramolecular gel containing equimolar amounts of the carboxyl group and the amidine group, which showed a high G′ value of about 1 MPa at room temperature and a T_gel of 37 °C. For comparison, the supramolecular polymer gels crosslinked by ammonium‐carboxylate salt were prepared using a linear polyethyleneimine instead of the polyamidine. The gel with equimolar amounts of the carboxyl group and the secondary amino group showed liquid‐like fluidity with a G′ value of about 0.01 MPa at room temperature, which was attributed to the fact that a certain amount of the carboxyl group remained as its free form without salt formation, as evidenced by FTIR analysis. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1815–1824     

Cationic polymerization of diglycidyl ether of bisphenol A

The cationic nonlinear polymerization of diglycidyl ether of Bisphenol A (DGEBA) in the presence of a diluent γ-butyrolactone (BL) was initiated by the BF₃-4-methoxyaniline (MA) complex. The reaction was studied by size exclusion chromatography, DSC, and dynamic mechanical analysis. Reaction mechanism involves a fast formation of adducts of DGEBA with MA released from the initiator. Formation of spiro orthoesters (S) by reaction of BL with DGEBA and homopolymerization of DGEBA as well as copolymerization with S follow. Gelation occurs at 60°C within a few minutes at conversion of epoxy groups (ξ_E)_c = 0.20–0.45. The networks cured under optimum conditions show high glass transition temperature, T_α = 178°C. The mechanism-structure-property relations are discussed. © 1994 John Wiley & Sons, Inc.     

A novel photoinimer for the polymerization of acrylates and methacrylates

A new class of multifunctional photoinitiating system based on 3‐(acryloyloxy)‐2‐hydroxypropyl methacrylate (AHM), N,N,N′‐trimethylethylenediamine (TMED) and 3‐benzoylbenzoyl chloride present in the same molecule has been synthesized and characterized by ¹H and ¹³C NMR spectroscopy. This self‐contained photoinitiator‐monomer (photoinimer) was used to efficiently initiate polymerization of acrylates and methacrylates. Both rate of polymerization and percentage conversion increased with increase in initiator concentration. An increment in rate of polymerization observed when the benzophenone moiety was directly attached to the parent molecule (obtained from the Michael addition reaction between AHM and TMED) appears to be due to proximity effect: chemical bonding provides a high local concentration of both components of the photo‐activated system involving benzophenone and a hydrogen atom source from an electron‐rich tertiary amine. For the three initiating systems investigated, lowering the initiator concentration plays an important role; i.e., the polymerization rate for the chemically linked system was about two times faster than the mixed initiating system. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5661–5670, 2005