The incorporation of carboxylate groups into temperature‐responsive poly(N‐isopropylacrylamide)‐based hydrogels promotes rapid gel shrinking

Aqueous gel deswelling rates for copolymer hydrogels comprising N‐isopropylacrylamide (IPAAm) and 2‐carboxyisopropylacrylamide (CIPAAm) in response to increasing temperatures were investigated. Compared with pure IPAAm‐based gels, IPAAm–CIPAAm gels shrink very rapidly in response to small temperature increases across their lower critical solution temperature (their volume is reduced by five‐sixths within 60 s). Shrinking rates for these hydrogels increase with increasing CIPAAm content. In contrast, structurally analogous IPAAm–acrylic acid (AAc) copolymer gels lose their temperature sensitivity with the introduction of only a few mole percent of AAc. Additionally, deswelling rates of IPAAm–AAc gels decrease with increasing AAc content. These results indicate that IPAAm–CIPAAm copolymer gels behave distinctly from IPAAm–AAc systems even if both comonomers, CIPAAm and AAc, possess carboxylic acid groups. Thus, we propose that the sensitive deswelling behavior for IPAAm–CIPAAm gels results from strong hydrophobic chain aggregation maintained between network polymer chains due to the similar chemical structures of CIPAAm and IPAAm. This structural homology facilitates aggregation of chain isopropylamide groups for both IPAAm and CIPAAm sequences with increasing temperature. The incorporation of AAc, however, shows no structural homology to IPAAm, inhibiting chain aggregation and limiting collapse. A functionalized temperature‐sensitive poly(N‐isopropylacrylamide) hydrogel containing carboxylic acid groups is possible with CIPAAm, producing rapid and large volume changes in response to smaller temperature changes. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 335–342, 2001     

From poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide)‐block‐poly(N‐isopropylacrylamide) triblock copolymer to poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide) hydrogels: Synthesis and rapid deswelling and reswelling behavior of hydrogels

Poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide)‐block‐poly(N‐isopropylacrylamide) (PNIPAAm‐b‐PEO‐b‐PNIPAAm) triblock copolymer was synthesized via the reversible addition‐fragmentation chain transfer/macromolecular design via the interchange of xanthate (RAFT/MADIX) process with xanthate‐terminated poly(ethylene oxide) (PEO) as the macromolecular chain transfer agent. The successful synthesis of the ABA triblock copolymer inspired the preparation of poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide) (PNIPAAm‐b‐PEO) copolymer networks with N,N′‐methylenebisacrylamide as the crosslinking agent with the similar approach. With the RAFT/MADIX process, PEO chains were successfully blocked into poly(N‐isopropylacrylamide) (PNIPAAm) networks. The unique architecture of PNIPAAm‐b‐PEO networks allows investigating the effect of the blocked PEO chains on the deswelling and reswelling behavior of PNIPAAm hydrogels. It was found that with the inclusion of PEO chains into the PNIPAAm networks as midblocks, the swelling ratios of the hydrogels were significantly enhanced. Furthermore, the PNIPAAm‐b‐PEO hydrogels displayed faster response to the external temperature changes than the control PNIPAAm hydrogel. The accelerated deswelling and reswelling behaviors have been interpreted based on the formation of PEO microdomains in the PNIPAAm networks, which could act as the hydrophilic tunnels to facilitate the diffusion of water molecules in the PNIPAAm networks. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermoresponsive properties of porous poly(N‐isopropylacrylamide) hydrogels prepared in the presence of nanosized silica particles and subsequent acid treatment

Porous poly(N‐isopropylacrylamide) hydrogels were prepared by the free‐radical polymerization of its monomer and a suitable crosslinker in the presence of spherical silica particles of different sizes (74 and 1600 nm) and by the subsequent acid extraction of silica. The yields were 81–83%, and the yields were not affected by the silica content. Scanning electron microscopy observations revealed the porous structure of the hydrogels. Porous and nonporous hydrogels showed volume phase transitions from swelling states to deswelling states at approximately 30 °C, as analyzed by the ratio of the diameter of cylinder‐shaped hydrogels to that of the glass tube used for the hydrogel preparation at the corresponding temperature. Deswelling, which was analyzed by rapid changes in the temperature of the aqueous media from 20 to 40 °C, was facilitated by decreased silica particle size and increased silica content. The deswelling rate constant of the hydrogel prepared with 74‐nm silica at 10 v/v % (silica/solvent) was more than 1500 times greater than that of conventional hydrogels. Swelling was similarly analyzed through changes in the temperature from 40 to 20 °C and was independent of the pore structure. The deswelling–swelling cycle was repeatable with reasonable reproducibility. Moreover, the mechanical strength of the porous hydrogels was significantly maintained compared with that of conventional nonporous hydrogels. This method produced thermoresponsive hydrogels of suitable mechanical strength and remarkable deswelling properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4228–4235, 2002     

Phase behaviors of partially ionized hydrogels in aqueous salt solutions: Applicability of the modified double‐lattice model

We investigated the effect of charge densities of the gel network and ionic strength of solution on swelling behaviors of ionized gels. We used the modified double‐lattice model, Flory–Erman's elastic model, and the ideal Donnan theory to describe swelling behaviors of the electrolyte bounded hydrogels. Energy parameters (?/k, δ?/k) were obtained from fitting liquid–liquid equilibria data of the linear poly‐N‐isopropylacrylamide/water system and two adjustable model parameters obtained from a nonelectrolyte hydrogel system. Calculated values agreed with experimental data for the given systems. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2333–2338, 2002     

Synthesis and swelling behavior of comb‐type grafted hydrogels by reversible addition–fragmentation chain transfer polymerization

The comb‐type grafted hydrogels poly(N‐isopropylacrylamide)‐g‐poly(N‐isopropylacrylamide) (PNIPAM‐g‐PNIPAM) and poly(acrylic acid)‐g‐poly(N‐isopropylacrylamide) (PAAc‐g‐PNIPAM) were prepared by reversible addition–fragmentation chain transfer polymerization. A macromolecular chain‐transfer agent was prepared first. Then, hydrogels were obtained by a reaction with a comonomer (N‐isopropylacrylamide or acrylic acid) in the presence of N,N‐methylenebisacrylamide as a crosslinker. The equilibrium swelling ratios and the swelling and deswelling kinetics of PNIPAM‐g‐PNIPAM were measured. The effects of the chain length and amount on the swelling behavior were investigated. The deswelling mechanism was illustrated. Meanwhile, the PAAc‐g‐PNIPAM hydrogel was used to confirm the versatility of this novel method. It was prepared in an alcoholic medium, whereas hydrogen‐bonding complexes formed in 1,4‐dioxane, which was chosen as the reaction medium for the PNIPAM‐g‐PNIPAM hydrogel. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2615–2624, 2005     

Preparation and characterization of macroporous poly(N‐isopropylacrylamide) hydrogels for the controlled release of proteins

Macroporous, temperature‐sensitive poly(N‐isopropylacrylamide) (PNIPAAm) hydrogels were synthesized with poly(ethylene glycol)s (PEGs; molecular weight = 2000–6000) as the pore‐forming agents. The influence of the molecular weight and PEG content on the responsive kinetics of these macroporous hydrogels was investigated. The PEG‐modified PNIPAAm hydrogels were characterized by the swelling ratio, deswelling–reswelling kinetics, Fourier transform infrared, and differential scanning calorimetry. The morphology of these hydrogels was analyzed with scanning electron microscopy. The prepared macroporous hydrogels exhibited some unique properties in comparison with the gels with low molecular weight PEGs (molecular weight < 2000) as the pore‐forming agents. In addition, a preliminary study on the controlled release of bovine serum albumin from these macroporous hydrogels was carried out. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 152–159, 2003     

Synthesis and characterization of polyhedral oligomeric silsesquioxane hybrid co‐crosslinked poly(N‐isopropylacrylamide‐co‐dimethylaminoethyl methacrylate) hydrogels

Polyhedral oligomeric silsesquioxane hybrid temperature and pH double‐responsive hydrogels with organic–inorganic co‐crosslinked networks are synthesized by in situ, free‐radical polymerization of N‐isopropylacrylamide and dimethylaminoethyl methacrylate in the presence of both organic crosslinker N,N′‐methylenebis(acrylamide) (BIS) and inorganic crosslinker octavinyl polyhedral oligomeric silsesquioxane (OvPOSS) in tetrahydrofuran media. The resulting hydrogels (OR‐OvP gels) display obvious temperature and pH double responsiveness, OvPOSS particles dispersed in polymer make a dominant effect on the properties of gels. With the increase of OvPOSS, the aggregation of particles on nano‐ or microscale happens and causes a considerable change on the properties of gels, such as the lower critical solution temperature and better compression strength. Specially, the interconnected microporous structure of gels ascribed to the microphase separation results in faster deswelling rate, which makes the gel become attractive. Besides, the crosslink by BIS intensifies the heterogeneity of gels significantly, which could also be used to adjust the properties of gels. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1494–1504     

Preparation and properties of chitosan‐poly(N‐isopropylacrylamide) semi‐IPN hydrogels

Chitosan (CS), CS‐poly(N‐isopropylacrylamide)(PNIPAM) and their dyed (pyrene) hydrogels were prepared using glutaraldehyde (Glu) as a crosslinker. The gelation rate, swelling behaviors in ethanol/water mixtures, electricity‐induced contraction and thermoresponse of the gels were investigated using fluorescence probe technique. Results showed that CS/Glu, and PNIPAM‐containing CS/Glu gels exhibited similar properties in all aspects examined, except that the transparence of the CS‐PNIPAM/Glu gel is very dependent upon the temperature. The CS‐PNIPAM/Glu gel is transparent below 30°C, whereas opaque above 32°C. It is expected that this observation may be useful for the design and preparation of new kinds of hydrogel devices. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 474–481, 2000     

Preparation of temperature‐responsive polymer gels physically immobilizing core‐shell type bioconjugates

Poly(N‐isopropylacrylamide) (PNIPAAm) gels are temperature‐responsive polymer gels; and were prepared by redox polymerization of N‐isopropylacrylamide in the presence of N,N′‐methylenebisacrylamide as a crosslinking reagent and core‐shell type bioconjugates, which were core‐crosslinked polyion complex micelles formed from the mixture of bovine pancreas trypsin and poly(ethylene glycol)‐block‐poly(α,β‐aspartic acid). The phase transition temperature of PNIPAAm gels was no change with physically immobilization of bioconjugates. Also, the enzymatic activity of bioconjugates was essentially maintained even in PNIPAAm gels, although enzymatic reaction rate was apparently controlled by temperature, i.e., by the degree of swelling of PNIPAAm gels. Further, the control of enzymatic reaction synchronizing the phase transition of PNIPAAm gels immobilized bioconjugates. PNIPAAm gels could immobilize core‐shell type bioconjugates, and were successfully prepared without interfering with the properties of temperature‐responsive polymer gels and the bionanoreactor. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5942–5948, 2007     

Organic–inorganic hybrid hydrogels involving poly(N‐isopropylacrylamide) and polyhedral oligomeric silsesquioxane: Preparation and rapid thermoresponsive properties

3‐Acryloxypropylhepta(3,3,3‐trifluoropropyl) polyhedral oligomeric silsesquioxane (POSS) was synthesized and used as a modifier to improve the thermal response rates of poly(N‐isopropylacrylamide) (PNIPAM) hydrogel. The radical copolymerization among N‐isopropylacrylamide (NIPAM), the POSS macromer and N,N′‐methylenebisacrylamide was performed to prepare the POSS‐containing PNIPAM cross‐linked networks. Differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) showed that the POSS‐containing PNIPAM networks displayed the enhanced glass transition temperatures (T_g's) and improved thermal stability when compared with plain PNIPAM network. The POSS‐containing PNIPAM hydrogels exhibited temperature‐responsive behavior as the plain PNIPAM hydrogels. It is noted that with the moderate contents of POSS, the POSS‐containing PNIPAM hydrogels displayed much faster response rates in terms of swelling, deswelling, and re‐swelling experiments than plain PNIPAM hydrogel. The improved thermoresponsive properties of hydrogels have been interpreted on the basis of the formation of the specific microphase‐separated morphology in the hydrogels, that is, the POSS structural units in the hybrid hydrogels were self‐assembled into the highly hydrophobic nanodomains, which behave as the microporogens and promote the contact of PNIPAM chains and water. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 504–516, 2009     

Thermal actuation of hydrogels from PNIPAm,alginate, and carbon nanofibres

Composite ionic‐covalent entanglement (ICE) hydrogel networks were prepared from poly(N‐isopropylacrylamide), alginate, and carbon nanofibres. An optimised triple network hydrogel with 86% water content exhibited a compressive strength of 3.0 ± 0.1 MPa and 66 ± 13 mS/cm electrical conductivity. Thermal actuation was shown to have a shorter response time for gels containing nanofibres, compared to those which did not and hydrogel samples more than halved in volume within 1 minute when placed in a 60 °C water bath. Controlled dye release was demonstrated as a potential application and used to further quantify thermal actuation over short times. Joule heating techniques were used to electronically actuate the hydrogel samples, removing the traditional requirements for immersion in a temperature controlled liquid. It is expected that devices based on these materials will find potential applications in soft robotics and micro fluidics. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 46–52     

Effects of guest microparticles on the swelling behavior of polyacrylamide gels

We report the effects of guest particles on the swelling properties of bulk polyacrylamide gels. The guest particles were the spheres of poly(N‐isopropylacrylamide) gel with submicrometer diameter, which were synthesized by an emulsion‐polymerized reaction in water. Polyacrylamide gels were prepared by a free radical polymerization reaction, immobilizing the gel microparticles with different concentrations at gelation. The macroscopic swelling ratio of this hybrid gel in a cylindrical shape was measured as functions of temperature and acetone concentration. The presence of guest particles was found to strongly affect the swelling behavior in the bulk gels when the concentration of incorporated particles exceeded a threshold. The experimental results indicated that the macroscopic volume in response to the temperature change should be determined by the guest particles above the threshold. On the other hand, the hybrid gel could not evidently shrink by adding acetone when the concentration of guest particles exceeded the threshold. To make clear the distribution of guest particles in the bulk networks, the fractured surfaces of dried gels were imaged by tapping mode atomic force microscopy. The guest particles were found to aggregate in the bulk homogeneous networks to form microdomains with densely connected structure, which became larger with increasing particle concentration. The roles of bulk networks as well as guest particles on the swelling behavior of hybrid gels were qualitatively discussed on the basis of the incorporated structure of guest particles, depending on the concentration of guest particles. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1696–1704, 2005     

Dual temperature‐ and pH‐sensitive hydrogels from interpenetrating networks and copolymerization of N‐isopropylacrylamide and sodium acrylate

Hydrogels responsive to both temperature and pH have been synthesized in the forms of sequential interpenetrating networks (IPNs) of N‐isopropylacrylamide (NIPAAm) and sodium acrylate (SA) and compared with the crosslinked random copolymers of N‐isopropylacrylamide and SA. Whereas the stimuli‐sensitive behaviors of copolymer hydrogels were strongly dependent on the ionic SA contents, the IPN hydrogels exhibited independent swelling and thermal behaviors of each network component. The sequences and media in the synthesis of IPNs influenced the swelling capacities of the IPNs, but not the temperature or pH ranges at which the swelling changes occurred. In IPNs, a more expanded primary gel network during the synthesis of the secondary network contributed to the better swelling of the final IPNs. Both the swelling and thermal behaviors of the IPNs suggest that poly(N‐isopropylacrylamide) and poly(sodium acrylate) are phase separated regardless of their synthesis conditions. The presence of the poly(sodium acrylate) network did not influence the temperature or the extent of phase transition of the poly(N‐isopropylacrylamide) network in the IPNs, but did improve the thermal stability of the IPNs. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3293–3301, 2004     

Synthesis of transition‐metal‐ion‐selective poly(N‐isopropylacrylamide) hydrogels by the incorporation of an Aza crown ether

A functionalized cyclam was synthesized by the attachment of a polymerizable acryloyl group to one of the four nitrogens on the cyclam molecule. The polymerization of the functionalized cyclam was performed with N‐isopropylacrylamide and N,N′‐methylene bisacrylamide, and the gels obtained were studied in the presence of different transition‐metal‐ion solutions. There was a drastic difference in the phase‐transition temperature (T_c) of the poly(N‐isopropylacrylamide) (PNIPAAm)/cyclam gel in comparison with the pure PNIPAAm gel. For the described system, a T_c shift of 15 °C was obtained. The presence of functionalized cyclam increased the hydrophilicity and T_c of the aforementioned polymer gels in deionized water (at pH 6) because of the presence of protonated amino moieties. The PNIPAAm/cyclam gels showed a dependence of the swelling behavior on pH. T_c of the pure PNIPAAm gel was weakly influenced by the presence of any transition‐metal ions, such as Cu²⁺, Ni²⁺, Zn²⁺, and Mn²⁺. The addition of Cu²⁺ or Ni²⁺ to the PNIPAAm/cyclam gel reduced T_c of the polymer gel, and a shift of approximately 12 °C was observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1594–1602, 2003     

Thermoresponsive conductivity of poly(N‐isopropylacrylamide)/potassium chloride gel electrolytes

A series of thermoresponsive polymer gel electrolytes (PGEs) based on poly(N‐isopropylacrylamide) in aqueous potassium chloride was synthesized by radiation‐induced polymerization and gelation using γ rays from a ⁶⁰Co source. The electric conductivity and swelling properties of the PGE were determined as a function of temperature. It was found that the electric conductivity of the PGE depended strongly on the swelling ratio; most notably, it changed drastically near the volume phase‐transition temperature of the PGE. The temperature/conductivity profile of the PGE exhibits a maximum peak at a certain temperature that is defined as the maximum conductivity temperature (T_max). The T_max of all of the PGEs prepared by low‐dose irradiation agreed with the temperature, near the end of the volume phase transition, where the PGE was completely shrunken. Consequently, the conductivity of gels should provide a good method with which the totally shrunken temperature of the thermoresponsive gels can be monitored with good temperature precision. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 134–141, 2002     

Self‐assembly of amphiphilic tris(2,2′‐bipyridine)ruthenium‐cored star‐shaped polymers

Amphiphilic tris(2,2′‐bipyridine)ruthenium‐cored star‐shaped polymers consisting of one polystyrene block and two poly(N‐isopropylacrylamide) blocks were prepared by the “arm‐first” method in which RAFT polymerization and nonconvalent ligand–metal complexation were employed. The prepared amphiphilic star‐shaped metallopolymers are able to form micelles in water. The size and distribution of the micelles were studied by dynamic light scattering and transmission electron microscopy techniques. Preliminary studies indicate that the polymer concentration and the hydrophilic poly(N‐isopropylacrylamide) block length can affect the morphologies of the formed metal‐interfaced core–shell micelles in water. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4204–4210, 2007     

Dual thermo‐ and pH‐sensitive network‐grafted hydrogels formed by macrocrosslinker as drug delivery system

Dual thermo‐ and pH‐sensitive network‐grafted hydrogels made of poly(N,N‐dimethylaminoethyl methacrylate) (PDMAEMA) network and poly(N‐isopropylacrylamide) (PNIPAM) grafting chains were successfully synthesized by the combination of atom transfer radical polymerization (ATRP), reversible addition‐fragmentation chain transfer (RAFT) polymerization, and click chemistry. PNIPAM having two azide groups at one chain end [PNIPAM‐(N₃)₂] was prepared with an azide‐capped ATRP initiator of N,N‐di(β‐azidoethyl) 2‐chloropropionylamide. Alkyne‐pending poly(N,N‐dimethylaminoethyl methacrylate‐co‐propargyl acrylate) [P(DMAEMA‐co‐ProA)] was obtained through RAFT copolymerization using dibenzyltrithiocarbonate as chain transfer agent. The subsequent click reaction led to the formation of the network‐grafted hydrogels. The influences of the chemical composition of P(DMAEMA‐co‐ProA) on the properties of the hydrogels were investigated in terms of morphology and swelling/deswelling kinetics. The dual stimulus‐sensitive hydrogels exhibited fast response, high swelling ratio, and reproducible swelling/deswelling cycles under different temperatures and pH values. The uptake and release of ceftriaxone sodium by these hydrogels showed both thermal and pH dependence, suggesting the feasibility of these hydrogels as thermo‐ and pH‐dependent drug release devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Thermo‐ and pH‐induced phase transitions and network parameters of poly(N‐isopropylacrylamide‐ co‐2‐acrylamido‐2‐methyl‐propanosulfonic acid) hydrogels

Dual temperature‐ and pH‐sensitive hydrogels composed of N‐isopropylacrylamide (NIPAM) and 2‐acrylamido‐2‐methyl‐propanosulfonic acid (AMPS) were prepared by free‐radical crosslinking copolymerization in aqueous solution at 22 °C. The mole percent of AMPS in the comonomer feed was varied between 0.0 and 7.5, while the crosslinker ratio was fixed at 5.0/100. The effect of AMPS content on thermo‐ and pH‐ induced phase transitions as well as equilibrium swelling/deswelling, interior morphology and network structure was investigated. The volume phase transition temperature (VPT‐T) was determined by both swelling/deswelling measurements and differential scanning calorimetry (DSC) technique. In addition, the volume phase transition pH (VPT‐pH) was detected from the derivative of the curves of the swelling ratio (dQ_v/dpH) versus pH. The polymer‐solvent interaction parameter (χ) and the average molecular mass between crosslinks ( ) of hydrogels were calculated from swelling ratios in buffer solutions at various pHs. The enthalpy (ΔH) and entropy (ΔS) changes appearing in the χ parameter of hydrogels were also determined by using the modified Flory–Rehner equation. The negative values for ΔH and ΔS indicated that the hydrogels had a negative temperature‐sensitive property in water, that is, swelling at a lower temperature and shrinking at a higher temperature. It was observed that the experimental swelling data of hydrogels at different temperature agreed with the modified Flory‐Rehner approach based on the affine network model. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1713–1724, 2008     

Amphiphilic conetworks. II. Novel two‐step synthesis of poly[2‐(dimethylamino)ethyl methacrylate]–polyisobutylene,poly(N‐isopropylacrylamide)–polyisobutylene,and poly(N,N‐dimethylacrylamide)–polyisobutylene hydrogels

Amphiphilic polymer conetworks consisting of hydrophilic poly[2‐(dimethylamino)ethyl methacrylate], poly(N‐isopropylacrylamide), or poly(N,N‐dimethylacrylamide) and hydrophobic polyisobutylene chains were synthesized with a novel two‐step procedure. In the first step, a methacrylate‐multifunctional polyisobutylene crosslinker was prepared by the cationic copolymerization of isobutylene with 3‐isopropenyl‐α,α‐dimethylbenzyl isocyanate. In the second step, the methacrylate‐multifunctional polyisobutylene crosslinker, with a number‐average molecular weight of 8200 and an average functionality of approximately 4 per chain, was copolymerized radically with 2‐(dimethylamino)ethyl methacrylate, N‐isopropylacrylamide, or N,N‐dimethylacrylamide into transparent amphiphilic conetworks containing 42–47 mol % hydrophilic monomer. The synthesized conetworks were characterized with solid‐state ¹³C NMR spectroscopy and differential scanning calorimetry. The amphiphilic nature of the conetworks was proved by swelling in both water and n‐heptane. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6378–6384, 2006     

An efficient synthesis of telechelic poly (N‐isopropylacrylamides) and its application to the preparation of α,ω‐dicholesteryl and α,ω‐dipyrenyl polymers

Poly(N‐isopropylacrylamide)s (PNIPAMs) with cholesteryl or pyrenyl moieties at each chain end (CH‐PNIPAMs or Py‐PNIPAMs) were prepared via end‐group modification of α,ω‐dimercapto poly(N‐isopropylacrylamides), ranging in molecular weight from ～ 7000 to 45,000 g mol^?1 with a polydispersity index of 1.10 or lower. The telechelic thiol functionalized PNIPAMs were obtained by aminolysis of α,ω‐di(isobutylthiocarbonylthio)‐poly(N‐isopropylacrylamide)s (iBu‐PNIPAMs) obtained by reversible addition‐fragmentation chain transfer (RAFT) polymerization of N‐isopropylacrylamide in the presence of the difunctional chain transfer agent, diethylene glycol di(2‐(1‐isobutyl)sulfanylthiocarbonylsulfanyl‐2‐methyl propionate) (DEGDIM). The self‐assembly of the polymers in water was assessed by fluorescence spectroscopy, using the intrinsic emission of Py‐PNIPAM or the emission of pyrene added as a probe in aqueous solutions of CH‐PNIPAM. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 314–326, 2008