Synthesis of 3‐Aryl‐2‐methoxyinden‐1‐one (Z)‐Phenylhydrazones via Hydrobromic Acid‐Mediated Cyclization of 2‐(1‐Aryl‐2‐methoxyethenyl)benzaldehyde Phenylhydrazones

2‐(1‐Aryl‐2‐methoxyethenyl)benzaldehydes 2 , obtained by successive treatment of 1‐(1‐aryl‐2‐methoxyethenyl)‐2‐bromobenzenes 1 with BuLi and 1‐formylpiperidine, were transformed to the corresponding phenylhydrazones 3 on treatment with PhNHNH₂. When these hydrazones were allowed to react with conc. HBr, cyclization, followed by dehydrogenation with air occurred, furnished 3‐aryl‐2‐methoxyinden‐1‐one (Z)‐phenylhydrazones 4 .     

Synthesis of 2‐Aryl‐2,3‐dihydro‐1,8‐naphthyridin‐4(1H)‐ones by Deprotective Cyclization of N‐{3‐[(2E)‐3‐Arylprop‐2‐enoyl]pyridin‐2‐yl}‐2,2‐dimethylpropanamides in Water

A new and convenient method for the preparation of 2‐aryl‐2,3‐dihydro‐1,8‐naphthyridin‐4(1H)‐ones 4 has been developed. Thus, N‐{3‐[(2E)‐3‐arylprop‐2‐enoyl]pyridin‐2‐yl}‐2,2‐dimethylpropanamides 3 are synthesized from commercially available pyridin‐2‐amine using an easily performed three‐step sequence and are subjected to cyclization with deprotection under acidic conditions in H₂O to give the desired products. Similarly, 2‐aryl‐2,3‐dihydro‐1,7‐naphthyridin‐4(1H)‐ones 8 and 2‐aryl‐2,3‐dihydro‐1,6‐naphthyridin‐4(1H)‐ones 12 can be prepared from pyridin‐3‐amine and pyridin‐4‐amine, respectively.     

Syntheses and Crystal Structures of Copper(II) and Silver Complexes with 5‐Methyl‐1‐(4‐Methylphenyl)‐1,2,3‐Triazol‐4‐Carboxylic Acid

Two novel complexes [Cu L ₂(MeOH)] ( 1 )and [Ag₂ L (H L )₂(MeOH)] ( 2 ) ( L = 5‐methyl‐1‐(4‐methylphenyl)‐1,2,3‐triazol‐4‐carboxylic acid) were synthesized and characterized by elemental analysis, IR and X‐ray diffraction. Complex 1 is a mononuclear structure; the molecules were assembled into an infinite 2–D supramolecular by the C–H···O weak interactions. Complex 2 is a centrosymmetric dinuclear structure with bis(unidentate) carboxylato co‐ordination mode, and the molecules were assembled into 2–D layers by C–H···O and O–H···O weak interactions.     

Poly(γ‐benzyl‐L‐glutamate)‐functionalized single‐walled carbon nanotubes from surface‐initiated ring‐opening polymerizations of N‐carboxylanhydride

Single‐walled carbon nanotubes (SWCNTs) have been functionalized with poly(γ‐benzyl‐L ‐glutamate) (PBLG) by ring‐opening polymerizations of γ‐benzyl‐L ‐glutamic acid‐based N‐carboxylanhydrides (NCA‐BLG) using amino‐functionalized SWCNTs (SWCNT‐NH₂) as initiators. The SWCNT functionalization has been verified by FTIR spectroscopy and transmission electron microscopy. The FTIR study reveals that surface‐attached PBLGs adopt random‐coil conformations in contrast to the physically absorbed or bulk PBLGs, which exhibit α‐helical conformations. Raman spectroscopic analysis reveals a significant alteration of the electronic structure of SWCNTs as a result of PBLG functionalization. The PBLG‐functionalized SWCNTs (SWCNT‐PBLG) exhibit enhanced solubility in DMF. Stable DMF solutions of SWCNT‐PBLG/PBLG with a maximum SWCNTs concentration of 259 mg L^?1 can be readily obtained. SWCNT‐PBLG/PBLG solid composites have been characterized by differential scanning calorimetry, thermogravimetric analysis, wide/small‐angle X‐ray scattering (W/SAXS), scanning electron microscopy, and polarized optical microscopy for their thermal or morphological properties. Microfibers containing SWCNT‐PBLG and PBLG can also be prepared via electrospinning. WAXS characterization reveals that SWCNTs are evenly distributed among PBLG rods in solution and in the solid state where PBLGs form a short‐range nematic phase interspersed with amorphous domains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2340–2350, 2010     

Design,Synthesis, and Evaluation of 3‐((4‐(t‐Butyl)‐2‐(2‐benzylidenehydrazinyl)thiazol‐5‐yl)methyl)quinolin‐2(1H)‐ones as Neuraminidase Inhibitors

A series of novel 3‐((4‐(t‐butyl)‐2‐(2‐benzylidenehydrazinyl)thiazol‐5‐yl)methyl)quinolin‐2(1H)‐ones ( 7a – 7z ) were designed, synthesized and evaluated for their ability of inhibiting neuraminidase (NA) of in?uenza H1N1 virus. Some compounds displayed moderate influenza NA inhibitory activity. Compound 7l with the scaffold of 2‐(2‐(2‐methoxybenzylidene)hydrazinyl)thiazole was the best one, exhibiting moderate NA inhibitory activity with IC₅₀ of 44.66 µmol/L. Structure‐activity relationship showed that compounds with methoxy or hydroxy groups at the ortho position, fluorine and nitro groups at the meta position and chlorine and bromine groups at the para position of phenyl ring were more active. Docking study indicated that compound 7l has important interactions with some key residues (including Asp151, Glu119, Arg292, Tyr406, and Asn347) and binds to 430‐cavity adjacent to NA active site.     

Synthesis of (4Z)‐4‐(Arylmethylidene)‐5‐ethoxy‐1,3‐oxazolidine‐2‐thiones by the Reaction of Ethyl (2Z)‐3‐Aryl‐2‐isothiocyanatoprop‐2‐enoates with Organolithium Compounds

A convenient one‐pot method for the preparation of (4Z)‐4‐(arylmethylidene)‐5‐ethoxy‐1,3‐oxazolidine‐2‐thiones 2 and 3 from ethyl (2Z)‐3‐aryl‐2‐isothiocyanatoprop‐2‐enoates 1 , which can be easily prepared from ethyl 2‐azidoacetate and aromatic aldehydes, has been developed. Thus, these α‐isothiocyanato α,β‐unsaturated esters were treated with organolithium compounds, including lithium enolates of acetates, to provide 5‐substituted (4Z)‐4‐(arylmethylidene)‐5‐ethoxy‐1,3‐oxazolidine‐2‐thiones, 2 , and 2‐[(4Z)‐(4‐arylmethylidene)‐5‐ethoxy‐2‐thioxo‐1,3‐oxazolidin‐5‐yl]acetates, 3 .     

Resonance raman spectra of poly‐(p‐phenylenebenzobisoxazole), poly‐(p‐phenylenebenzobisthiazole), and poly(pyridobisimidazole)

Resonance Raman spectra of poly(p‐phenylenebenzobisoxazole) (PBO), poly(p‐phenylenebenzobisthazole) (PBZT), and poly(pyridobisimidazole) (PIPD) were measured. In the case of PBO, no large dependence on wavelength of excited laser can be observed, whereas in the cases of PBZT and PIPD, the spectra depends on wavelength of excited laser. This difference may be attributed to the colors of the samples: PBO is gold, and PBZT and PIPD are metallic blue, which show the different conjugated states. The spectra of PBO are rather simpler than those of PBZT and PIPD. This is considered to be reflected by the fact that only a chain passes through the unit cell of PBO, while two chains pass through the unit cell of PBZT and PIPD. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1791–1793, 2001     

Effect of Medium Acidity and Photostability of 3‐(4‐Dimethylamino‐phenyl)‐1‐(2,5‐dimethyl‐thiophen‐3‐yl)‐propenone (DDTP): A New Green Emitting Laser Dye

On the line of a previous work on the spectral properties of some of heteroaryl chalcone, the effect of medium acidity and photoreactivity of 3‐(4‐dimethylamino‐phenyl)‐1‐(2,5‐dimethyl‐thiophen‐3‐yl)‐propenone (DDTP) has been investigated in dimethylformamide and in chloromethane solvents such as methylenechloride, chloroform and carbon tetrachloride. The dye solution (ca. 5×10⁻⁴ mol·L⁻¹ in DMF) gives a good laser emission in the range 470–560 nm with emission maximum at 515 nm upon pumping by nitrogen laser (λ_ex=337.1 nm). The laser parameters such as gain coefficient (α), emission cross section (δ_e) and half life energy (E_1/2) at maximum laser emission are also determined.     

Chiral separation of amides of amino acid on a (S)‐N‐(3,5‐dinitrobenzoyl)leucine‐N‐phenyl‐N‐propylamide‐bonded silica using nonaqueous capillary electrochromatography

(S)‐N‐(3,5‐dinitrobenzoyl)leucine‐N‐phenyl‐N‐propylamine‐bonded silica was used as a chiral stationary phase for separation of a set of racemic π‐acidic and π‐basic α‐amino acid amides in electrolyteless ACN‐water eluents by CEC in the RP and polar organic (PO) modes. The effect of the amount of water in the ACN‐water eluent on chiral separation was examined. As water is added to ACN, retention was shortened but resolution and selectivity deteriorated severely. Retention, enantioselectivity, and resolution factors obtained in 100% ACN were compared with those in an n‐hexane‐isopropanol eluent with a small amount of water by normal phase (NP) CEC. Much shorter retention times with comparable enantioselectivities were observed with 100% ACN, demonstrating the advantage of separation on (S)‐N‐(DNB)leucine‐N‐phenyl‐N‐propylamine‐bonded silica in PO‐CEC over NP‐CEC.     

One‐Pot Synthesis of N,N‐Disubstituted (Z)‐4‐(Halomethylidene)‐4H‐3,1‐benzothiazin‐2‐amines from 2‐(2,2‐Dihaloethenyl)phenyl Isothiocyanates and Secondary Amines

We have developed a one‐pot procedure for the preparation of N,N‐disubstituted (Z)‐4‐(halomethylidene)‐4H‐3,1‐benzothiazin‐2‐amines 3 from 2‐(2,2‐dihaloethenyl)phenyl isothiocyanates 1 , easily accessible from known 2‐(2,2‐dihaloethenyl)benzenamines by a three‐step sequence, and secondary amines. Thus, the isothiocyanates 1 react with secondary amines to afford the corresponding thiourea derivatives, of which the treatment with NaH provides the desired products.     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

HPLC法拆分(-)-2(S)-苄基-4-酮-4-(顺式-全氢化异吲哚-2-基)丁酸钙对映体

目的：建立刺激胰岛素分泌的新型降糖药物(-)-2 (S)-苄基-4-酮-4-(顺式-全氢化异吲哚-2-基)丁酸钙对映体的HPLC拆分方法。方法：采用Sumichiral OA-3300手性柱(250 × 4.6 mm I.D., 5 μm), 柱温35℃,以0.05 mol·L-1醋酸铵的甲醇溶液为流动相,检测波长为210 nm。结果：本品两对映体在22分钟内实现良好分离,分离度达3以上,S－异构体分别在0.028 ~ 5.6 μg mL-1和0.03 ~ 6.0 μg mL-1范围内线性关系良好,回归方程分别为：Y=1.32×103x-2.54 (r=0.9997)和Y=1.15×103x-1.78 (r=0.9998),最低检测限分别为0.15 ng和0.10 ng,方法精密度RSD低于1.0% (n=5)。结论：建立的对映体分离方法可用于本品光学异构体的质量控制。     

Electronic spectra and first‐order hyperpolarizability of 4‐(dicyanomethylene)‐2,6‐bis‐ (2′‐thiophene‐vinyl)‐pyran derivatives

On the basis of the ZINDO program, we have designed a program to calculate the first‐order hyperpolarizability β_ijk and β_μ according to the sum‐over‐states (SOS) expression. The first‐order hyperpolarizability of 4‐(dicyanomethylene)‐2,6‐bis‐(2′‐thiophene‐vinyl)‐pyran derivatives were studied. The calculated results were that the 4‐(dicyanomethylene)‐2,6‐bis‐(2′‐thiophene‐vinyl)‐pyran derivatives exhibit good nonlinearity with their β₀ values, which are slightly less than that of the corresponding 2,6‐bis‐styryl‐4‐(dicyanomethylene)‐pyran derivatives. It does not agree with the auxiliary donor–acceptor effects theory. The 4‐(dicyanomethylene)‐2,6‐bis‐(2′‐thiophene‐vinyl)‐pyran derivatives, having two low‐lying electronic excited states that contribute to the molecular hyperpolarizability in an additive manner, are good candidates as chromophores due to their high nonlinearities and good thermal stability. © 2001 John Wiley & Sons, Inc. Int J Quant Chem 82: 65–72, 2001     

Copper(II)‐Catalyzed Synthesis of N‐Substituted‐3‐amino‐4‐cyano‐isoquinoline‐1(2H)‐ones by the Reaction of N‐Substituted‐2‐iodobenzamides with Malononitrile

A novel Cu(OAc)₂·H₂O catalyzed coupling reaction of N‐substituted‐2‐iodobenzamides with malononitrile to afford N‐substituted‐3‐amino‐4‐cyano‐isoquinoline‐1(2H)‐ones is described. The reaction proceeded in DMSO at 90°C for 5 h in nitrogen without external ligands.     

Biodegradable electrospun mat: Novel block copolymer of poly (p‐dioxanone‐co‐L‐lactide)‐block‐poly(ethylene glycol)

Ultrafine fibers of a laboratory‐synthesized new biodegradable poly(p‐dioxanone‐co‐L ‐lactide)‐block‐poly(ethylene glycol) copolymer were electrospun from solution and collected as a nonwoven mat. The structure and morphology of the electrospun membrane were investigated by scanning electron microscopy, differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), and a mercury porosimeter. Solutions of the copolymer, ranging in the lactide fraction from 60 to 80 mol % in copolymer composition, were readily electrospun at room temperature from solutions up to 20 wt % in methylene chloride. We demonstrate the ability to control the fiber diameter of the copolymer as a function of solution concentration with dimethylformamide as a cosolvent. DSC and WAXD results showed the relatively poor crystallinity of the electrospun copolymer fiber. Electrospun copolymer membrane was applied for the hydrolytic degradation in phosphate buffer solution (pH = 7.5) at 37 °C. Preliminary results of the hydrolytic degradation demonstrated the degradation rate of the electrospun membrane was slower than that of the corresponding copolymers of cast film. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1955–1964, 2003     

Thermal Behaviors of 2‐(Dinitromethylene)‐1,3‐diazacycloheptane (DNDH)

2‐(Dinitromethylene)‐1,3‐diazacycloheptane (DNDH) was prepared by the reaction of 1,1‐diamino‐2,2‐dinitroethylene (FOX‐7) with 1,4‐diaminoethane in NMP. Thermal decomposition behavior of DNDH was studied under the non‐isothermal conditions with DSC method, and presents only one intensely exothermic decomposition process. The kinetic equation of the decomposition reaction is dα/dT=10^33.88×3α^2/3exp(−3.353×10⁵/RT)/β. The critical temperature of thermal explosion is 215.97°C. Specific heat capacity of DNDH was studied with micro‐DSC method and theoretical calculation method, and the molar heat capacity is 215.40 J·mol⁻¹·K⁻¹ at 298.15 K. Adiabatic time‐to‐explosion was calculated to be 92.07 s. DNDH has same thermal stability to FOX‐7.     

Synthesis,Crystal Structure and Thermal Behavior of 4,5‐Diacetoxyl‐2‐(dinitromethylene)‐imidazolidine

A new energetic material, 4,5‐diacetoxyl‐2‐(dinitromethylene)‐imidazolidine (DADNI), was synthesized by the reaction of 4,5‐dihydroxyl‐2‐(dinitromethylene)‐imidazolidine (DDNI) and acetic anhydride, and characterized by single crystal X‐ray diffraction. Crystal data for DADNI are monoclinic, space group C2/c, a=15.9167(3) Å, b=8.6816(4) Å, c=8.5209(3) Å, β=103.294(9)°, V=1145.9(3) ų, Z=4, µ=0.150 mm⁻¹, F(000)=600, D_c=1.682 g·cm⁻³, R₁=0.0565 and wR₂=0.1649. Thermal decomposition behavior of DADNI was studied and an intensely exothermic process was observed. The kinetic equation of the decomposition reaction is: dα/dT=(10^16.64/β)×4α^3/4exp(−1.582×10⁵/RT). The critical temperature of thermal explosion is 163.76°C. The specific heat capacity of DADNI was studied with micro‐DSC method and theoretical calculation method. The molar heat capacity is 343.30 J·mol⁻¹·K⁻¹ at 298.15 K. The adiabatic time‐to‐explosion of DADNI was calculated to be 87.7 s.     

Synthesis and properties of ortho‐linked aromatic polyimides based on 1,2‐bis(4‐aminophenoxy)‐4‐tert‐butylbenzene

A bis(ether amine) containing the ortho‐substituted phenylene unit and pendant tert‐butyl group, 1,2‐bis(4‐aminophenoxy)‐4‐tert‐butylbenzene, was synthesized and used as a monomer to prepare polyimides with six commercial dianhydrides via a conventional two‐stage procedure. The intermediate poly(amic acid)s had inherent viscosities of 0.78–1.44 dL/g, and most of them could be thermally converted into transparent, flexible, and tough polyimide films. The inherent viscosities of the resulting polyimides were in the range of 0.46–0.87 dL/g. All polyimides were noncrystalline, and most of them showed excellent solubility in polar organic solvents. The glass‐transition temperatures of these polyimides were in the range of 222–259 °C in differential scanning calorimetry and 212–282 °C in thermomechanicl analysis. These polyimides showed no appreciable decomposition up to 500 °C in thermogravimetric analysis in air or nitrogen. A comparative study of the properties with the corresponding polyimides without pendant tert‐butyl groups derived from 1,2‐bis(4‐aminophenoxy)benzene is also presented. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1551–1559, 2000     

Formation and Molecular Structure of an Ion Pair Iron (II) Compound Derived from 2,6‐Bis‐ [1‐(2,6‐dibromophenylimino) ‐ethyl] pyridine and 2‐Acetyl‐6‐[1‐(2, 6‐dibromophenylimino)‐ethyl] pyridine

Two novel tridentate ligands of 2,6‐bis‐[l‐(2,6‐dibromophenylimino) ethyl] pyridine (L₁) and2‐acetyl‐6‐[1‐(2,6‐dibromophenylimino) ethyl] pyridine (L2) have been synthesized. The iron(II) complex of L₁ and L₂ has been characterized with the crystal structure of [Fe(L₁)(L₂)]²⁺ [FeCl₄]² CH₂Cl₂ [monoclinic, P2₁ (#11), a = 1.0562(4), b = 2.0928(4), c = 1.2914(2) nm, β = 100.12°, V = 2.810(1) nm³ D_c = 1.879 g/cm³ and Z = 2].     

Chain composition dependence of luminescence properties for copolymers of 2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene and 2,3‐diphenyl‐5‐octyl‐1,4‐phenylenevinylene

The copolymers of 2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene (MEH‐PV) and 2,3‐diphenyl‐5‐octyl‐1,4‐phenylenevinylene were prepared via the Gilch route with their chain compositions and the reactivity ratios of the monomers estimated by ¹H NMR spectroscopy. The results indicated that the copolymers tended to form an alternative copolymer as the feed ratio of the monomers closed to one‐half. When an individual copolymer solution in tetrahydrofuran was spun‐cast to form a film, the MEH‐PV units were able to attract the like units from the adjacent chains. As a result, the ultraviolet–visible absorption spectrum of the alternative copolymer in film form was broader than the spectra of those with different compositions. The photoluminescence spectra of the copolymers in film form exhibited the characteristic shoulder of poly(2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene), even though the content of MEH‐PV units was not great enough for the formation of repeat units in sequence. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2180–2186, 2003