Oxygen‐barrier properties of copolymers based on ethylene terephthalate

The oxygen‐barrier properties of amorphous polyethylene terephthalate‐based copolymers with various acid comonomers were examined. The incorporation of increasing amounts of isophthalate, phthalate, or naphthalate gradually reduced the permeability P toward the low values obtained for the corresponding homopolymers. The permeability of poly(ethylene 3,4′‐bibenzoate) homopolymer was only slightly lower than that of polyethylene terephthalate, and the copolymers correspondingly exhibited a very gradual decrease in P as the amount of 3,4′‐bibenzoate (3,4′BB) increased. In contrast, copolymerization with the linear isomer, 4,4′BB, produced a substantial increase in P. Generally, comonomer affected the solubility S less than the diffusivity D, and therefore changes in P reflected primarily changes in D for the polymers studied. The diffusivity and solubility depended on the copolymer composition in accordance with static and dynamic free‐volume concepts of gas permeability in glassy polymers. The solubility S correlated with the amount of free volume as determined by the glass‐transition temperature. Correlation of the diffusivity D with the magnitude of the subambient γ relaxation identified dynamic free volume with thermally activated conformational changes and segmental motions. Correspondence in the activation energy confirmed the relationship. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1889–1899, 2001     

Effect of crystallization on oxygen‐barrier properties of copolyesters based on ethylene terephthalate

The effect of crystallization from the glassy state (cold crystallization) on the oxygen‐barrier properties of copolyesters based on ethylene terephthalate with up to 10 mol % isophthalate, phthalate, or naphthalate was examined. Generally, crystallization affected diffusivity D more than solubility S; thus, the reduction in permeability P reflected primarily a reduction in D. Systematic changes in crystallinity made it possible to test free‐volume concepts in which permeation of a small gas molecule through a semicrystalline polymer is viewed as proceeding through the amorphous regions with an increased pathway (tortuosity) imposed by plateletlike crystallites. Of the copolymers studied, those with the highest isophthalate or phthalate content (10 mol %) conformed to the simple two‐phase model with constant densities of an impermeable crystalline phase and a permeable amorphous phase. Within the two‐phase model, solubility S correlated linearly with the volume fraction of the amorphous phase, and diffusivity D depended on crystallinity in accordance with the Nielsen model for randomly dispersed platelets with an aspect ratio of 4. The reduction in permeability of the other examined copolyesters could not be described only by the filler effect of crystallites. Data on solubility demonstrated a decrease in amorphous‐phase density upon cold crystallization (de‐densification) like that previously reported for polyethylene terephthalate. Increasing the isophthalate or phthalate content reduced the de‐densification effect, and 10 mol % of these comonomers was sufficient to eliminate the effect altogether. In contrast, 10 mol % naphthalate did not prevent de‐densification. This was attributed to different effects of kinked and linear comonomers on chain packing in the amorphous phase. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1911–1919, 2001     

Oxygen‐barrier properties of cold‐drawn polyesters

The improvement of oxygen‐barrier properties of glassy polyesters by orientation was examined. Poly(ethylene terephthalate) (PET), poly(ethylene naphthalate), and a copolymer based on PET in which 55 mol % of the terephthalate was replaced with bibenzoate (PET‐BB55) were oriented by constrained uniaxial stretching. In a fairly narrow window of stretching conditions near the glass‐transition temperature, it was possible to achieve uniform extension of the polyesters without crystallization or stress whitening. The processes of orientation and densification correlated with the conformational transformation of glycol linkages from gauche to trans. Oxygen permeability, diffusivity, and solubility decreased with the amount of orientation. A linear relationship between the oxygen solubility and polymer specific volume suggested that the cold‐drawn polyester could be regarded as a one‐phase densified glass. This allowed an analysis of oxygen solubility in accordance with free‐volume concepts of gas permeability in glassy polymers. Orientation was seen as the process of decreasing the amount of excess‐hole free volume and bringing the nonequilibrium polymer glass closer to the equilibrium (zero‐solubility) condition. Cold drawing most effectively reduced the free volume of PET‐BB55. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 862–877, 2002     

Diels–Alder modification of poly(ethylene terephthalate‐co‐anthracene‐2,6‐carboxylate) with N‐substituted maleimides

Dimethyl 2,6‐anthracene dicarboxylate is used as a comonomer in the synthesis of functional copolymers that are subject to modification with Diels–Alder reactions. The formation of poly(ethylene terephthalate‐co‐2,6‐anthracenate), containing less than 20 mol % of the anthracene‐2,6‐dicarboxylate structural units, provides materials that are tractable and soluble. The anthracene units of the copolymers undergo Diels–Alder reactions with N‐substituted maleimides. The grafting of N‐alkylmaleimides affords soluble, hydrophobic polymers, whereas grafting with maleimide‐terminated poly(ethylene glycol) affords hydrophilic polymers. Because this reaction proceeds below the melting point of the copolymers, the procedure can be applied to thin films, whereby the surface properties are modified. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3256–3263, 2002     

Permeability of N2, Ar,He, O2, and CO2 through as‐extruded amorphous and biaxially oriented polyester films: Dependence on chain mobility

For as‐extruded amorphous and biaxially orientated polyester films based on poly(ethylene terephthalate), poly(ethylene naphthalate), and copolymers containing poly(ethylene terephthalate) and poly(ethylene naphthalate) moieties, permeability, diffusion, and solubility coefficients are interpreted in terms of chain mobility. The influence of polymer morphology is determined by comparison of the data for as‐extruded amorphous sheets and materials produced with different biaxial draw ratios. The crystallinities of the samples were assessed using differential scanning calorimetry and density measurements. Changes in mobility at a molecular level were investigated using dielectric spectroscopy and dynamic mechanical thermal analysis. The study, in conjunction with our earlier work, leads to the conclusion that the key to understanding differences in gas transport is the difference in local chain motions rather than in free volume. This was illustrated by the permeability results for He, Ar, N₂, and O₂ in the range of polyesters. However, the permeability of CO₂ was found to require alternative explanations because of polymer–penetrant interactions. For biaxially oriented samples, the differences in diffusivity are not only due to differences in local chain motions, but also additional constraints resulting from the increased crystallinity and chain rigidity—which also act to hinder segmental mobility. The effectiveness of the reduction in permeability in the biaxially oriented films is consequently determined by the ability of the polymer chains to effectively align and form crystalline structures. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2916–2929, 2004     

Free volume and oxygen transport in cold‐drawn polyesters

Poly(ethylene terephthalate) (PET), poly(ethylene terephthalate‐co‐4,4′‐bibenzoate) (PETBB55), and poly(ethylene 2,6‐naphthalate) (PEN) were cold‐drawn to achieve uniform extension without crystallization or stress whitening, and oxygen transport properties were studied at temperatures from 10 to 40 °C. Correlation of oxygen solubility and polymer specific volume made it possible to consider the oriented polyester as a one‐phase densified glass. Orientation was viewed as decreasing the amount of excess‐hole free volume and bringing the nonequilibrium polymer glass closer to the equilibrium condition. Between 10 and 40 °C, the amount of excess‐hole free volume in PET decreased as the polymer approached the glass transition temperature. In contrast, temperature changes in this range had little effect on the excess‐hole free volume in PETBB55 and PEN, which were well below their glass transition temperature. Gas diffusion was viewed as discrete jumps of the oxygen molecule between holes of excess‐free volume. The jump length was extracted from the activation energy for diffusion according to a channel‐formation model. The result agreed well with the hole spacing estimated from a simple lattice model using the hole density reported in the literature. Extending the lattice model to estimate the mean excess‐free volume hole radius from the fractional free volume resulted in good correlation with the hole radius obtained from positron annihilation lifetime spectroscopy. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 493–504, 2004     

Synthesis,physical characterization,and acetone sorption kinetics in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Random copolymers of poly(ethylene terephthalate) (PET) and poly(ethylene 2,6-naphthalate) (PEN) were synthesized by melt condensation. In a series of thin, solvent cast films of varying PEN content, acetone diffusivity and solubility were determined at 35°C and an acetone pressure of 5.4 cm Hg. The kinetics of acetone sorption in the copolymer films are well described by a Fickian model. Both solubility and diffusivity decrease with increasing PEN content. The acetone diffusion coefficient decreases 93% from PET to PET/85PEN, a copolymer in which 85 weight percent of the dimethyl terephthalate in PET has been replace by dimethyl naphthalate 2,6-dicarboxylate. The acetone solubility coefficient in the amorphous regions of the polymer decreases by approximately a factor of two over the same composition range. The glass/rubber transition temperatures of these materials rise monotonically with increasing PEN content. Copolymers containing 20 to 80 wt % PEN are amorphous. Samples with <20% or >80% PEN contain measurable levels of crystallinity. Estimated fractional free volume in the amorphous regions of these samples is lower in the copolymers than in either of the homopolymers. Relative free volume as probed by positron annihilation lifetime spectroscopy (PALS) decreases systematically with increasing PEN content. Acetone diffusion coefficients correlate well with PALS results. Infrared spectroscopy suggests an increase in the fraction of ethylene glycol units in the trans conformation in the amorphous phase as the concentration of PEN in the copolymer increases. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2981–3000, 1998     

Permeability,permselectivity, and penetrant‐induced plasticization in fluorinated polyimides studied by positron lifetime measurements

The ortho‐positronium (o‐Ps) lifetime τ₃ and its intensity I₃ in various fluorinated polyimides were determined by the positron annihilation technique and were studied with the spin–lattice relaxation time T₁ and the propylene permeability, solubility, diffusivity, and permselectivity for propylene/propane in them. τ₃, I₃, and the distribution of τ₃ changed when the bulky moieties in the polyimides were changed. The polyimides, having both large τ₃ and I₃ values, exhibited a short T₁ and a high permeability with a low permselectivity. The propylene permeability and diffusivity were exponentially correlated with the product of I₃ and the average free‐volume hole size estimated from τ₃. In highly plasticized states induced by the sorption of propylene, the permeability increased with the propylene pressure in excellent agreement with the change in the free‐volume hole properties probed by o‐Ps. The large and broad distribution of the free‐volume holes and increased local chain mobility for the 2,2‐bis(3,4‐decarboxyphenyl) hexafluoropropane dianhydride‐based polyimides are thought to be important physical properties for promoting penetrant‐induced plasticization. These results suggest that o‐Ps is a powerful probe of not only the free‐volume holes but also the corresponding permeation mechanism and penetrant‐induced plasticization phenomenon. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 308–318, 2003     

Transesterification kinetics of poly(ethylene terephthalate) and poly(ethylene 2,6‐naphthalate) blends with the addition of 2,2′‐bis(1,3‐oxazoline)

The kinetics of the transesterification reaction between poly(ethylene terephthalate) (PET) and poly(ethylene 2,6‐naphthalate) (PEN) with and without the addition of a chain extender were studied with ¹H NMR. Different kinetic approaches were considered, and a second‐order, reversible reaction was accepted for the PET/PEN reactive blend system. The addition of 2,2′‐bis(1,3‐oxazoline) (BOZ) promoted the transesterification reaction between PET and PEN in the molten state. The activation energy of the transesterification reaction for the PET/PEN reactive blend with BOZ (94.0 kJ/mol) was lower than that without BOZ (168.9KJ/mol). The rate constant k took an almost constant value for blend samples with different compositions mixed at 275 °C. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2607–2614, 2001     

Oxygen‐barrier properties of cold‐crystallized and melt‐crystallized poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

This study examined the oxygen‐transport properties of poly(ethylene terephthalate‐co‐bibenzoate) (PETBB55) crystallized from the melt (melt crystallization) or quenched to glass and subsequently isothermally crystallized by heating above the glass‐transition temperature (cold crystallization). The gauche–trans conformation of the glycol linkage was determined by infrared analysis, and the crystalline morphology was examined by atomic force microscopy. Oxygen solubility decreased linearly with volume fraction crystallinity. For melt‐crystallized PETBB55, extrapolation to zero solubility corresponded to an impermeable crystal with 100% trans glycol conformations, a density of 1.396 g cm^?3, and a heat of melting of 83 J g^?1. From the melt, PETBB55 crystallized as space‐filling spherulites with loosely organized lamellae and pronounced secondary crystallization. The morphological observations provided a structural model for permeability consisting of impermeable platelets randomly dispersed in a permeable matrix. In contrast, cold‐crystallized PETBB55 retained the granular texture of the quenched polymer despite the high level of crystallinity, as measured by the density and heat of melting. Oxygen solubility decreased linearly with volume fraction crystallinity, but zero solubility corresponded to an impermeable defective crystal with a trans fraction of 0.83 and a density of 1.381 g cm^?3. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2489–2503, 2002     

Gas permeability and hydrocarbon solubility of poly[1‐phenyl‐2‐[p‐(triisopropylsilyl)phenyl]acetylene]

The effects of film thickness, physical aging, and methanol conditioning on the solubility and transport properties of glassy poly[1‐phenyl‐2‐[p‐(triisopropylsilyl) phenyl]acetylene] are reported at 35 °C. In general, the gas permeability coefficients are very high, and this polymer is more permeable to larger hydrocarbons (e.g., C₃H₈ and C₄H₁₀) than to light gases such as H₂. The gas permeability and solubility coefficients are higher in as‐cast, unaged films than in as‐cast films aged at ambient conditions and increase to a maximum in both unaged and aged as‐cast films after methanol conditioning. For example, the oxygen permeability of a 20‐μm‐thick as‐cast film is initially 100 barrer and decreases to 40 barrer after aging for 1 week at ambient conditions. After methanol treatment, the oxygen permeabilities of unaged and aged films increase to 430 and 460 barrer, respectively. Thicker as‐cast films have higher gas permeabilities than thinner as‐cast films. Propane and n‐butane sorption isotherms suggest significant changes in the nonequilibrium excess free volume in these glassy polymer films due to processing history. For example, the nonequilibrium excess free volume estimated from the sorption data is similar for as‐cast, unaged samples and methanol‐conditioned samples; it is 100% higher in methanol‐conditioned films than in aged, as‐cast films. The sensitivity of permeability to processing history may be due in large measure to the influence of processing history on nonequilibrium excess free volume and free volume distribution. The propane and n‐butane diffusion coefficients are also sensitive to film processing history, presumably because of the dependence of diffusivity on free volume and free volume distribution. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1474–1484, 2000     

Sorption and transport of linear alkane hydrocarbons in biaxially oriented polyethylene terephthalate

Equilibrium sorption and uptake kinetics of n‐butane and n‐pentane in uniform, biaxially oriented, semicrystalline polyethylene terephthalate films were examined at 35 °C and for pressures ranging from 0 to approximately 76 cmHg. Sorption isotherms were well described by the dual‐mode sorption model. Sorption kinetics were described either by Fickian diffusion or a two‐stage model incorporating Fickian diffusion at short times and protracted polymer structural relaxation at long times. Diffusion coefficients increased with increasing penetrant concentration. n‐Butane solubility was lower than that of n‐pentane, consistent with the more condensable nature of n‐pentane. However, n‐butane diffusion coefficients were higher than those of n‐pentane. Infinite‐dilution, estimated amorphous phase diffusion and solubility coefficients were well correlated with penetrant critical volume and critical temperature, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 1160–1172, 2001     

Effect of water sorption on oxygen‐barrier properties of aromatic polyamides

Aromatic polyamides based on poly(m‐xylylene adipamide) (MXD‐based polyamides) and poly(hexamethylene isophthalamide) (HMD‐based polyamides) were examined. Insight into the excellent gas‐barrier properties was obtained by the characterization of the effect of water sorption on the thermal transitions, density, refractive index, free‐volume hole size, and oxygen‐transport properties. Reversing the carbonyl position with respect to the amide nitrogen substantially lowered the oxygen permeability of MXD‐based polyamides in comparison with that of HMD‐based polyamides by facilitating hydrogen‐bond formation. The resulting restriction of conformational changes and segmental motions reduced diffusivity. The primary effect of water sorption was a decrease in the glass‐transition temperature (T_g) attributed to plasticization by bound water. No evidence was found to support the idea that sorbed water filled holes of free volume. When the polymer was in the glassy state, the drop in T_g accounted for hydration‐dependent changes in the density, refractive index, and free‐volume hole size. The correlation of the oxygen solubility with T_g and density confirmed the concept of oxygen sorption as filling holes of excess free volume. In some cases, water sorption produced a glass‐to‐rubber transition. The onset of rubbery behavior was associated with a minimum in the oxygen permeability. The glass‐to‐rubber transition also facilitated the crystallization of MXD‐based polymers, which complicated the interpretation of oxygen‐transport behavior at higher relative humidity. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1365–1381, 2005     

Effects of tertiary amines and quaternary ammonium halides in polysulfone on membrane gas separation properties

Polymers containing CO₂‐philic groups are of great interest for CO₂/light gas separation membranes because the affinity toward CO₂ can effectively increase CO₂ solubility and thus permeability. In this study, polysulfones (PSUs) modified with different degrees of benzyldimethylamine (DMA), benzyltrimethylammonium fluoride (TMAF), and benzyltrimethylammonium iodide (TMAI) were synthesized using sequential post‐functionalization reactions and investigated for CO₂/N₂ and CO₂/CH₄ separation. The physical properties of these polymers were studied, including density, fractional free volume, and glass transition temperature. In contrast to the conventional wisdom that tertiary amines exhibit an affinity toward CO₂, this study convincingly shows that the DMA substituent has a minimal impact on CO₂ solubility and CO₂/light gas solubility selectivity in PSUs under dry condition. On the other hand, incorporating TMAF and TMAI in PSU significantly increases CO₂ solubility. Particularly, introducing TMAI with a molar ratio of 1.07 relative to PSU repeating units increases CO₂/CH₄ solubility from 4.4 to 5.2, CO₂/CH₄ permeability selectivity from 21 to 45, and CO₂/N₂ permeability selectivity from 24 to 33 at 35 °C, while the CO₂ permeability decreases from 5.6 to 1.7 Barrers. The effect of these functional groups in PSUs on gas diffusivity and diffusivity selectivity can be satisfactorily described by the free volume model. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1239–1250     

Effects of physical aging on solubility,diffusivity, and permeability of propane and n-butane in poly(4-methyl-2-pentyne)

The effects of physical aging on the solubility, diffusivity, and permeability of propane and n-butane in a hydrocarbon-based disubstituted polyacetylene, poly(4-methyl-2-pentyne) (PMP), were studied. As the relative pressure of propane and n-butane increased, the solubility of both hydrocarbons increased. Like other glassy polymers, the sorption isotherms for propane and n-butane in all PMP films were concave to the relative pressure axis, indicating dual-mode sorption behavior. The diffusion of propane and n-butane in PMP followed typical Fickian diffusion in a plane sheet. The propane diffusivity in both the unaged and aged films increased with increasing concentration of propane sorbed in the film. The n-butane diffusivity in aged films also increased with increasing n-butane concentration. However, unaged films showed the opposite behavior: the diffusivity decreased with increasing n-butane concentration. These diffusion phenomena are a consequence of the interplay between thermodynamic and mobility factors. The permeabilities of propane and n-butane decreased monotonically with increasing penetrant concentration, similar to the behavior observed in other common glassy polymers. The relaxation of the nonequilibrium excess free volume in PMP films induced the decrease in both solubility and diffusivity. As a result, the permeability of propane and n-butane in PMP decreased upon physical aging. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2407–2418, 2004     

Oxygen permeability in thermoplastic polyurethanes

The thermal and oxygen transport properties of a series of thermoplastic polyurethanes (TPUs) based on 4,4′‐methylene diisocyanate (MDI) and 1,4‐butanediol (BD) as hard segments, and poly(tetramethylene glycol) (PTMG) or poly(butylene adipate) (PA) as soft segments, are studied. Oxygen permeabilities (P) of both polyester‐based and polyether‐based TPUs increase with decreasing hard segment fractions. Oxygen solubility (S) and diffusivity (D) can be derived from permeation curves. S correlates with the amount of excess free volume as determined by the difference between glass‐transition and testing temperatures (i.e., the degree of super cooling) and decreases with the increased T_g in polyester‐based TPUs. The intensity of low temperature gamma transition reflects the activation energy for D; the higher the intensity is, the lower D is annealed TPU samples exhibited higher oxygen permeabilities as well as lower storage moduli at room temperature, despite modest increases in overall crystallinity. Dedensification of the soft segment phase during annealing/crystalline phase growth is the most likely explanation for loss of mechanical and barrier properties after annealing as partially confirmed by Fourier transform infrared spectroscopy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Permeation measurements in ethylene‐1‐hexene,ethylene‐1‐octene,and ethylene‐1‐dodecene copolymers synthesized with metallocene catalysts

The permeation behavior of different ethylene‐1‐hexene, ethylene‐1‐octene, and ethylene‐1‐dodecene copolymers synthesized with metallocene catalysts has been analyzed. These copolymers cover a wide range of comonomer contents, so their crystallinities display rather considerable variations. The results for the permeability to oxygen of the different ethylene copolymers show that the main factor influencing the permeability is the noncrystalline fraction, although some influence of the kind of comonomer may also be present, which may be explained by the fact that when the alkyl branch of the α‐olefin is longer, there is an increase in the free volume in the amorphous and interfacial regions, causing slightly higher values of the permeability coefficient. From the results with different gases, it follows that, in general, an increase in the size of the penetrant (as expressed by its kinetic diameter or critical molar volume) leads to an increase in the solubility and a decrease in the diffusion coefficient. A wide range of permeability values is covered by these ethylene copolymers, depending basically on the crystallinity of the sample, but the permselectivity of CO₂ with respect to oxygen (and probably between other pairs of gases) does not differ very much among the different copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2174–2184, 2003     

The synthesis,characterization, and crystal structures of poly(2,6‐naphthalenebenzobisoxazole) and poly(1,5‐naphthalenebenzobisoxazole)

The rigid‐rod polymers, poly(2,6‐naphthalenebenzobisoxazole) (Naph‐2,6‐PBO) and poly(1,5‐naphthalenebenzobisoxazole) (Naph‐1,5‐PBO) were synthesized by high temperature polycondensation of isomeric naphthalene dicarboxylic acids with 4,6‐diaminoresorcinol dihydrochloride in polyphosphoric acid. Expectedly, these polymers were found to have high thermal as well as thermooxidative stabilities, similar to what has been reported for other polymers of this class. The chain conformations of Naph‐2,6‐PBO and Naph‐1,5‐PBO were trans and the crystal structures of Naph‐2,6‐PBO and Naph‐1,5‐PBO had the three‐dimensional order, although the axial disorder existed for both Naph‐2,6‐PBO and Naph‐1,5‐PBO. Naph‐2,6‐PBO exhibited a more pronounced axial disorder than Naph‐1,5‐PBO because of its more linear shape. The repeat unit distance for Naph‐2,6‐PBO (14.15 Å) was found to be larger compared with that of Naph‐1,5‐PBO (12.45 Å) because of the more kinked structure of the latter. The extents of staggering between the adjacent chains in the ac projection of the crystal structure were 0.25c and 0.23c for Naph‐2,6‐PBO and Naph‐1,5‐PBO, respectively. Naph‐1,5‐PBO has a more kinked and twisted chain structure relative to Naph‐2,6‐PBO. The kinked and twisted chain structure of Naph‐1,5‐PBO in the crystal seems to prevent slippage between adjacent chains in the crystal structure. The more perfect crystal structure of Naph‐1,5‐PBO may be due to this difficulty in the occurrence of the slippage. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1948–1957, 2006     

Effect of molecular association on solubility,diffusion, and permeability in polymeric membranes

The filling‐type membrane is composed of grafted polymer and solvent‐resistant substrate; the calculation of solubility, diffusivity and swelling‐suppression effect by the substrate permits the prediction of solvent permeability. As noted in our previous article, the use of this approach, called membrane design, resulted in accurate prediction of the permeability of aromatic compounds. In this study, the influence of hydrogen bonding on solubility and diffusivity is investigated both theoretically and experimentally. The solubility of chloroform and dichloromethane in poly(acrylate)s increases, and their diffusivity decreases, compared with that estimated without considering the hydrogen‐bonding effect. Solubilities predicted by the lattice‐fluid hydrogen‐bonding (LFHB) model show good agreement with the results of vapor sorption. Comparison of diffusion coefficients measured by vapor permeation with those predicted from free volume theory reveals that the decrease of solvent diffusion coefficient is approximately proportional to the fraction of associated molecules. Fluxes of chloroform and dichloromethane were measured by vapor permeation experiments through filling‐type acrylate membranes, and predictions agree well with experiments. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 171–181, 2000     

Gas permeability and n‐butane solubility of poly(1‐trimethylgermyl‐1‐propyne)

The gas permeability and n‐butane solubility in glassy poly(1‐trimethylgermyl‐1‐propyne) (PTMGP) are reported. As synthesized, the PTMGP product contains two fractions: (1) one that is insoluble in toluene and soluble only in carbon disulfide (the toluene‐insoluble polymer) and (2) one that is soluble in both toluene and carbon disulfide (the toluene‐soluble polymer). In as‐cast films, the gas permeability and n‐butane solubility are higher in films prepared from the toluene‐soluble polymer (particularly in those films cast from toluene) than in films prepared from the toluene‐insoluble polymer and increase to a maximum in both fractions after methanol conditioning. For example, in as‐cast films prepared from carbon disulfide, the oxygen permeability at 35 °C is 330 × 10^?10 cm³ (STP) cm/(cm² s cmHg) for the toluene‐soluble polymer and 73 × 10^?10 cm³ (STP) cm/(cm² s cmHg) for the toluene‐insoluble polymer. After these films are conditioned in methanol, the oxygen permeability increases to 5200 × 10^?10 cm³ (STP) cm/(cm² s cmHg) for the toluene‐soluble polymer and 6200 × 10^?10 cm³ (STP) cm/(cm² s cmHg) for the toluene‐insoluble polymer. The rankings of the fractional free volume and nonequilibrium excess free volume in the various PTMGP films are consistent with the measured gas permeability and n‐butane solubility values. Methanol conditioning increases gas permeability and n‐butane solubility of as‐cast PTMGP films, regardless of the polymer fraction type and casting solvent used, and minimizes the permeability and solubility differences between the various films (i.e., the permeability and solubility values of all conditioned PTMGP films are similar). © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2228–2236, 2002