Deterioration of a polyurethane coating studied by positron annihilation spectroscopy: Correlation with surface properties

Deterioration of a polyurethane coating by Florida natural environments as a function of time up to 16 weeks was studied by positron annihilation spectroscopy. Doppler broadening energy spectroscopy (DBES) of annihilation irradiation and positron annihilation lifetime (PAL) were measured as a function of incident positron energy (0–30 keV). A significant decrease in the S‐defect parameter from DBES and the intensity of orthopositronium from PAL was observed as a function of weathering time. This is interpreted as a loss of free volume and holes as a result of the weathering process. The gloss and surface morphology in the same system were measured by glossimetry and atomic force microscopy (AFM), respectively. The gloss decreased and surface roughness increased as a function of weathering time. The AFM images showed a new feature of a spherically coagulated microstructure on the surface after weathering. Direct correlations between the decrease in gloss and the increase in roughness as well as the decrease in the S‐defect parameter from the DBES data and in the free volume from the PAL data were observed. These results were used to discuss the weathering process in terms of chemical and physical changes as a result of photodegradation in protective polymeric systems. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2290–2301, 2001     

Study of the photodegradation of epoxy polymers with slow positron annihilation spectroscopy

The photodegradation of an amine‐cured epoxy coating after exposure to accelerated UV‐340 and UV‐313 irradiation was investigated with an atomic‐level technique, positron annihilation spectroscopy (PAS), which detected and characterized the free volumes and defects as a function of the depth. Significant changes in the subnanometer defect parameters S and W were observed as a function of the exposure time near the surface. This was interpreted as due to a loss of the free volume and hole fraction resulting from photodegradation. A dead layer near the surface, resulting from UV irradiation from the surface up to a thickness of 0.4 μm, at which there was nearly no positronium formation, was observed. Correlations between physical defects from PAS in terms of the free volumes and chemical defects from electron spin resonance spectroscopy in terms of free radicals and chemical structural changes measured by ultraviolet–visible and Fourier transform infrared spectroscopy were established. A high sensitivity of PAS for detecting the early stage of degradation, on the order of hours for UV‐313 and on the order of days for UV‐340 irradiation, was observed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2441–2459, 2004     

Degradation of polymer coating systems studied by positron annihilation spectroscopy. II. Correlation with free radical formation

The photo‐degradation of polymer coating systems due to irradiation by UV and Xenon light sources is studied using positron annihilation spectroscopy and electron spin resonance (ESR). Doppler broadened spectra of positron annihilation, as a function of slow positron implantation energy and ESR spectra, are measured in two types of polyurethane which were exposed, ex situ, to UV irradiation for up to 800 h. The UV irradiation systematically decreases the S parameter as a function of exposure duration and increases the ESR signals. Thus, significant S parameter decrease is correlated with the ESR signal increase resulting from photo‐degradation of polymers due to UV irradiation. Parallel in situ positron annihilation and ESR experiments are performed as a function of Xenon light exposure for up to 100 min. These results show that the photo‐degradation of the polyurethane coatings involves initial free‐radical formation, which is correlated with the subnanometer defects detected by positron annihilation spectroscopy. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1289–1305, 1999     

Positron annihilation studies on radiation‐crosslinked poly(N‐isopropylacrylamide) hydrogels

The temperature‐sensitive poly(N‐isopropylacrylamide) hydrogels, prepared by γ and electron‐beam (EB) irradiation, were studied using positron annihilation lifetime spectroscopy (PALS). The effect of water content in the hydrogel on the ortho‐positronium (o‐Ps) lifetime and intensity was investigated. The observed positronium lifetime suggests microstructural differences between γ‐ and EB‐synthesized hydrogels. The distribution in positronium lifetime indicates nonhomogeneity in the distribution of free‐volume holes in EB‐synthesized hydrogels. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3462–3466, 2000     

Visibly observed photocrosslinking reaction in indolyl based pendant liquid crystalline polymers: Synthesis and optical property

Visibly observed photocrosslinkable pendant liquid crystalline polymers containing indolyl based chalcone were synthesized by free‐radical polymerization and characterized spectroscopically. The differential scanning calorimetry and polarized optical microscopy were used to examine liquid crystalline property. The photocrosslinking and luminescence properties were monitored by UV‐Vis spectrophotometer and spectrofluorimeter, respectively. It demonstrates the chalcone unit did not manifest cis ? trans‐isomerization reaction along with 2π+2π photodimerization upon irradiation with UV light like other chalcones hitherto reported. The photocrosslinking was visibly monitored in solution through change of fluorescent color to colorless. The spacer lengths play a key role in the reaction. The fluorescence maximum was blue shifted around 70 nm in chloroform solution upon irradiation with UV light confirms the 2π+2π photodimerization of chalcone unit. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5208–5220, 2009     

Photolysis of bisphenol‐based polyurethanes in solution

Photolysis of bisphenol‐based polyurethanes, using bisphenols A, S, and AF with methylene diphenyl diisocyanate (MDI), has been shown by the observed changes in fluorescence spectra, reduced viscosity, and UV absorbance. Analysis of the fluorescence spectra of model compounds and polymers showed that para‐photo‐Fries and cleavage‐type products were the major components formed during photolysis. The reduced viscosity and UV absorbance changes are consistent with a two‐step photodegradation process. The reduced viscosity changes indicate that oxygen inhibition on the cleavage process is more significant for bisphenol S‐based polyurethanes than for bisphenol A‐ and bisphenol AF‐based polyurethanes. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1331–1339, 1999     

Application of slow positrons to coating degradation

Photodegradation of a polyurethane-based topcoat induced by accelerated UV irradiation is studied using Doppler broadened energy spectra (DBES) and positron annihilation lifetime (PAL) spectroscopies coupled with slow positron technique. Significant and similar variations of S-parameter and ortho-positronium intensity (I₃) in coatings are observed as functions of depth and of exposure time. The decrease of S is interpreted as a result of an increase of crosslink density and a reduction of free-volume and hole fraction during the degradation process.     

The hydrogen bond and free volume property of poly(ether‐urethane) irradiated by neutron

Poly(ether‐urethane) (PEU) was irradiated by neutron in different atmospheres. The hydrogen bonding interaction was analyzed by Fourier transform infrared (FTIR), and the microstructure of PEU had been investigated by positron annihilation lifetime spectroscopy (PALS). The gas products were detected by gas chromatography after irradiation. The results demonstrated that the irradiation led to more hydrogen bonded carbonyl in PEU, smaller relative free volume fraction, and narrower free volume distribution. It suggested that increasing hydrogen bonds would result in the collapse of free volume. The irradiation induced micro‐phase merging together and the presence of oxygen would accelerate this tendency, which was revealed by PALS. All the results indicated that the chain relaxation led to more hydrogen bonds, and the hydrogen bonding interaction suppressed the free volume. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 381–388, 2010     

Properties of nitrocellulose‐coated and polyethylene‐laminated chitosan and whey films

Chitosan (chitosan acetic acid salt) and whey (65% protein) films were coated with a nitrocellulose lacquer or laminated with polyethylene to enhance their water resistance and gas barrier properties in humid environments. The barrier properties were measured by the Cobb₆₀ test and water‐vapor (100% relative humidity) transmission and oxygen (90% relative humidity) permeability tests. Mechanical properties were obtained with tensile tests. Packaging properties were studied with crease and folding tests. The Cobb₆₀ test revealed that the coated films were resistant to liquid water, at least for a short exposure time, if the coating thickness was at least 10–17 μm. Water‐vapor transmission rates comparable to those of polyethylene‐laminated films were obtained for coated chitosan at a coating thickness of 5–7 μm. The coated films possessed low oxygen permeability despite the high humidity. Coated films dried for 3 weeks showed oxygen permeabilities at 90% relative humidity that were similar to values for dry ethylene‐co‐vinyl alcohol at 0% relative humidity. The lacquer partly penetrated the whey films, and this led to excellent adhesion but poor lacquer toughness. The lacquer coating on chitosan was tougher, and it was possible to fold these films 90° without the coating fracturing if the coating thickness was small. The coated whey films were readily creasable. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 985–992, 2001     

Polythiophene formation within hyperbranched grafts on polyethylene films

Interphase oligomerization of thiophene within a supported thin film is described. Polyethylene (PE) surfaces containing an irregularly hyperbranched poly(acrylic acid) (PAA) graft were first prepared by multistep grafting of poly(tert‐butylacrylate) onto oxidized PE. The product ultrathin PAA grafts were then further modified by amidation or esterification with thiophenes containing amino or hydroxyl groups to form new interfaces containing thiophene monomers. These thiophene‐modified grafts were characterized by attenuated total reflectance infrared spectroscopy and were shown to be suitable as substrates in an oxidative polymerization method with FeCl₃ as an oxidant. The product 2,5‐coupled thiophene oligomers (3‐PAA/PE–oligomerized thiophene ester, OTE) emitted a yellow‐green light under UV irradiation, indicating that a conjugated fluorescence oligothiophene had been prepared within these hyperbranched films. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4119–4128, 2001     

Effect of residual water and free volume on the glass‐transition temperature and heat capacity in polystyrene/poly(vinyl acetate‐co‐butyl acrylate) structured latex films

The dynamic heat capacity and glass‐transition temperature of polystyrene (PS)/poly(vinyl acetate‐co‐butyl acrylate) (VAc–BA) (50:50 w/w) structured latex films as a function of annealing time at 70, 77, and 85 °C were examined with modulated‐temperature differential scanning calorimetry. The PS and poly(vinyl acetate‐co‐n‐butyl acrylate) components were considered to be the cores and shells, respectively, in the structured latex. The dynamic heat capacity decreased with time. The glass‐transition temperatures of the PS and VAc–BA phases shifted to higher values after annealing. The results of thermogravimetry showed that there existed about 1.8% residual water in the films. The mean free volume and relative concentration of holes at room temperature (before and after annealing) and 85 °C, as a function of time, were obtained with positron annihilation lifetime spectroscopy (PALS). The PALS results indicated no significant change in free volume during annealing. It is believed that the loss, by diffusion, of residual water mainly caused a decrease in heat capacity and an increase in the glass‐transition temperatures. As little as 1.8% residual water in the structured latex films had a significant influence on the thermal properties. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1659–1664, 2001     

Free radical photopolymerization initiated by UV and LED: Towards UV stabilized,tack free coatings

UV stabilizers (UV absorbers and Hindered Amine Light Stabilizers‐HALS) are added to UV‐curable formulations to provide long‐term durability. The influence of HALS and the filtering effect of UV absorbers are investigated under UV and LED irradiation by using different photoinitiating systems in free radical photopolymerization. The contribution of irradiation conditions and initiating systems on the filtering effect is discussed by performing Real‐Time Fourier Transform Infrared Spectroscopy (RT‐FTIR) and Confocal Raman Microscopy. Additionally, to get quantitative information about the light absorbed by the photoinitiator, without and with the filtering issue arising from UV stabilizers, series of calculations are carried out by taking into account the amount of light absorbed by the compounds and the intensity of the incident light. Finally, formulations are optimized with respect to surface inhibition to obtain tack free coatings in air atmosphere in the presence of UV stabilizers under visible light. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3597–3607     

Role of radicals in UV‐initiated postplasma grafting of poly‐ε‐caprolactone: An electron paramagnetic resonance study

Electron paramagnetic resonance (EPR) measurements were performed on poly‐ε‐caprolactone (PCL) films at different stages of the postplasma‐grafting process. PCL films prepared by solvent casting (SC) or electrospinning (ESP) yield very similar EPR spectra after Ar‐plasma treatment and subsequent exposure to air, but the EPR signal is much stronger in the PCL‐ESP films. The free radicals appear to be mainly, and possibly exclusively, oxygen centered. The radicals generated by UV irradiation in PCL‐ESP films were studied in situ with EPR, using a UV‐LED (λ = (285 ± 5) nm). Their EPR spectrum is distinctly different from the plasma‐induced signal, indicative of carbon‐centered radicals, and appears to be independent of the plasma pretreatment. UV‐induced homolytic splitting of (hydro)peroxide bonds was not observed. Both the plasma‐ and UV‐induced radicals decay at room temperature (RT), even in an inert atmosphere. This study demonstrates the potential of electrospun films and UV‐LEDs for the study of plasma‐ and UV‐generated free radicals with EPR in polyesters, and raises questions with respect to the validity of some generally accepted molecular mechanisms underpinning the postplasma grafting technique for polyesters. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of polymer particles possessing radical initiating sites on the surface by emulsion copolymerization and construction of core–shell structures by a photoinduced atom transfer radical polymerization approach

The crosslinked polystyrene particles possessing photofunctional N,N‐diethyldithiocarbamate groups on their surface were prepared by free‐radical emulsion copolymerization of a mixture of styrene, divinylbenzene and 4‐vinylbenzyl N,N‐diethyldithiocarbamate with redox system as an initiator under UV irradiation. In this copolymerization, the inimer 4‐vinylbenzyl N,N‐diethyldithiocarbamate acted the formation of hyperbranched structures by living radical photopolymerization. The particle sizes (number‐average particle diameter = 214–523 nm) were controlled by varying the feed amount of surfactant and size distributions were relatively narrow. Subsequently, core–shell particles were synthesized by photoinduced atom transfer radical polymerization approach of methyl methacrylate initiated by photofunctional polystyrene particles as a macroinitiator. Such core–shell particles were stabilized sterically by grafted chains in organic solvents. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1771–1777, 2007     

Controlled polymerization of acrylic acid under 60Co irradiation in the presence of dibenzyl trithiocarbonate

The polymerization of acrylic acid (AA) was performed under ⁶⁰Co irradiation in the presence of dibenzyl trithiocarbonate at room temperature, and well‐defined poly(acrylic acid) (PAA) with a low polydispersity index was successfully prepared. The gel permeation chromatographic and ¹H NMR data showed that this polymerization displays living free‐radical polymerization characteristics: a narrow molecular weight distribution (M_w/M_n = 1.07–1.22), controlled molecular weight, and constant chain‐radical concentration during the polymerization. Using PAA? S? C(?S)? S? PAA as an initiator, the extension reaction of PAA with fresh AA was carried out under ⁶⁰Co irradiation, and the results indicated that this extension polymerization displayed controlled polymerization behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3934–3939, 2001     

Free volume changes on optical switching in azobenzene‐polymethylmethacrylate blends studied by a pulsed low‐energy positron beam

Polymers including chromophores, which can be switched by light, have been studied extensively during the last years due to a host of potential applications which arise from the marked changes in physical properties on switching. Even though there is clear evidence that the free volume has a significant influence on the isomerization kinetics, the question of free volume changes on switching was only addressed recently. Using a pulsed low‐energy positron beam the ortho‐positronium lifetime τ₃ was taken as a very sensitive free volume probe, and no change in free volume was detected on isomerization in an azobenzene‐polymethylmethacrylate (PMMA) copolymer containing about 8 wt % of the azobenzene moiety. Here, we report for the first time on free volume changes in an azobenzene‐PMMA blend with an azobenzene moiety concentration as high as 40 wt %. Using the same pulsed low‐energy positron beam, small but significant changes of τ₃ were observed between the structurally relaxed dark and the UV‐illuminated states suggesting a decrease in free volume of the order of 10%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Metal nanocomposite films prepared in situ from PVA and silver nitrate. Study of the nanostructuration process and morphology as a function of the in situ routes

Cast‐hybrid films composed of polyvinyl alcohol (PVA) and silver nitrate were treated according to three different ways, thermal annealing, UV‐irradiation, and chemical reduction by a borohydride solution, to obtain PVA/silver nanocomposite films. The nanostructuration process was studied as a function of the treatment conditions, and discussed as a function of the mobility state of the polymer chains in the nanocomposite matrix during treatment. A homogeneous dispersion of crystalline silver nanoparticles was obtained by thermal annealing above T_g and below T_m and UV‐lamp irradiation below T_g. For these two treatments, the major processing parameters were the annealing temperature and time and the UV‐exposure time, respectively. For low‐conversion rate in Ag(0), the films evolved upon ageing at room temperature. Totally different morphology and Ag(0) conversion were achieved by chemical reduction in a borohydride solution. All the silver ions were reduced into Ag(0), and crystalline silver nanoparticles layers parallel to the film surface were observed after the treatment. This morphology was related to the high‐swollen state of the polymer matrix during treatment. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2062–2071, 2008     

Triplet‐sensitized irradiation of a main‐chain liquid crystalline poly(aryl cinnamate) in three different phases

Visible light irradiation of thin films of a main‐chain liquid crystalline poly(aryl cinnamate) using ketocoumarins as triplet sensitizers leads to photochemical crosslinking and UV‐vis and FTIR spectroscopic changes associated with saturation of the cinnamate double bond, most likely by 2 + 2 photocycloaddition. The triplet sensitizers are themselves photolabile and are lost by photochemical reactions during the sensitization process. A new ketocoumarin sensitizer with decyloxy substituents and a reduced tendency to phase separate from the polymer is reported. A simple calculation of the sensitization stoichiometry shows that a single molecule of this ketocoumarin sensitizes the destruction of approximately 90 cinnamate chromophores in the “as cast” films below T_g and about 300 chromophores in the more‐ordered glassy nematic films and in “as cast” films of poly(vinyl cinnamate). Triplet sensitization of fluid nematic films leads, upon initial irradiation, to UV‐vis hyperchromism that is attributed to disruption of chromophore aggregation and, possibly, to disruption of the nematic mesophase as photoproducts begin to form. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 134–144, 2001     

Synthesis of epoxy monomers that undergo synergistic photopolymerization by a radical‐induced cationic mechanism

A series of novel, cycloaliphatic, cationically photopolymerizable epoxide monomers bearing benzyl ether groups were prepared. These monomers display a considerable enhancement in the rate of their cationic ring‐opening polymerizations in comparison with monomers that do not contain such groups. In this article, a synergistic free‐radical mechanism is proposed that accounts for this effect, and supporting evidence is offered for its verification. During UV irradiation of an onium salt cationic photoinitiator, the aryl radicals that are generated abstract labile benzyl hydrogens present in such monomers to generate the corresponding carbon‐centered radicals. Subsequently, these radicals are oxidized to benzyl carbocations by the onium salt via a nonphotochemical chain process. The observed increase in the rate and extent of the cationic ring‐opening polymerization of the epoxide monomers is due to the aforementioned mechanism, which effectively increases the number of reactive cationic species present during polymerization. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3578–3592, 2001