Nylon 610/functionalized multiwalled carbon nanotube composite prepared from in‐situ interfacial polymerization

Pristine multiwalled carbon nanotubes (P‐MWNTs) were functionalized with 4‐chlorobenzoic acid via “direct” Friedel‐Crafts acylation in polyphosphoric acid (PPA)/phosphorous pentoxide (P₂O₅) medium. The resultant 4‐chlorobenzoyl‐functionalized MWNTs (F‐MWNTs) were soluble in chlorinated solvents such as dichloromethane, chloroform, and carbon tetrachloride. A large scale of nylon 610/F‐MWNT composite could be conveniently prepared by in situ interfacial polymerization of 1, 6‐hexamethylenediamine (HMDA) in an aqueous phase, and sebacoyl chloride with F‐MWNTs in an organic phase. Similarly, nylon 610/P‐MWNT composite was also prepared for comparison. The state of F‐MWNTs dispersion in nylon 610 matrix was distinctively better than that of P‐MWNTs, which could be clearly discerned by both naked eye and scanning electron microcopy (SEM). As a result, the tensile strength of nylon 610/F‐MWNT composite was 4.9‐fold higher than that of nylon 610/P‐MWNT composite. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6041–6050, 2008     

Microemulsion polymerization of styrene stabilized by sodium dodecyl sulfate and short‐chain alcohols

Styrene microemulsion polymerizations with different short‐chain alcohols [n‐C_iH_2i+1OH (C_iOH), where i = 4, 5, or 6] as the cosurfactant were investigated. Sodium dodecyl sulfate and sodium persulfate (SPS) were used as the surfactant and initiator, respectively. The desorption of free radicals out of latex particles played an important role in the polymerization kinetics. An Arrhenius expression for the radical desorption rate coefficient was obtained from the polymerizations at temperatures of 50–70 °C. The polymerization kinetics were not very sensitive to the alkyl chain length of alcohols compared with the temperature effect. The maximal polymerization rate in decreasing order was C₆OH > C₄OH > C₅OH. This was related to the differences in the water solubility of C_iOH and the structure of the oil–water interface. The feasibility of using a water‐insoluble dye to study the particle nucleation mechanisms was also evaluated. The parameters chosen for the study of the particle nucleation mechanisms include the cosurfactant type (C_iOH), the SPS concentration, and the initiator type (oil‐soluble 2,2′‐azobisisobutyronitrile versus water‐soluble SPS). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3199–3210, 2001     

Synthesis and characterization of high molecular weight atactic polybutene‐1 with a monotitanocene/methylaluminoxane catalyst system

A novel catalyst precursor, the monotitanocene (η⁵‐pentamethylcyclopentadienyl) titanium tricinnamyloxide [Cp*Ti(OCH₂? CH?CHC₆H₅)₃], was synthesized and employed for butene‐1 polymerization in the presence of methylaluminoxane. The effects of the polymerization conditions on the catalytic activity, molecular weight, stereoregularity, and regioregularity of the polymer so obtained were investigated in detail. The results show that the monotitanocene is desirable for the production of atactic polybutene‐1 coupled with good yields under typical polymerization conditions, high molecular weight (weight‐average molecular weight = 5.3–9.6 × 10⁵), and stereoirregularity with the Bernoullian factor B equal to 0.95, which indicates that chain‐end control is predominant. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4068–4073, 2001     

Controlled polymerization of acrylic acid under 60Co irradiation in the presence of dibenzyl trithiocarbonate

The polymerization of acrylic acid (AA) was performed under ⁶⁰Co irradiation in the presence of dibenzyl trithiocarbonate at room temperature, and well‐defined poly(acrylic acid) (PAA) with a low polydispersity index was successfully prepared. The gel permeation chromatographic and ¹H NMR data showed that this polymerization displays living free‐radical polymerization characteristics: a narrow molecular weight distribution (M_w/M_n = 1.07–1.22), controlled molecular weight, and constant chain‐radical concentration during the polymerization. Using PAA? S? C(?S)? S? PAA as an initiator, the extension reaction of PAA with fresh AA was carried out under ⁶⁰Co irradiation, and the results indicated that this extension polymerization displayed controlled polymerization behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3934–3939, 2001     

Synthesis of phosphate end‐functional polymers and application to thermally latent polymeric initiators

Novel phosphates, O‐p‐(hydroxymethyl)benzyl O,O‐diethyl phosphate ( 1 ) and O‐(2‐bromoisobutyryloxymethyl)benzyl O,O‐diethyl phosphate ( 2 ) were synthesized by the reaction of diethyl phosphorochloridate with 1,4‐benzenedimethanol and the successive reaction with 2‐bromoisobutyryl bromide in the presence of triethylamine and submitted to the polymerization of ?‐caprolactone and methyl methacrylate as the initiators. They afforded phosphate end‐functional poly(?‐caprolactone) and poly(methyl methacrylate) with controlled molecular weights and polydispersity ratios by living ring‐opening polymerization and samarium‐induced polymerization. The polymerization of glycidyl phenyl ether (GPE) was carried out with the phosphate end‐functional polymers as the latent polymeric initiators in the presence of ZnCl₂. The polymerization of GPE did not proceed below 90 °C, but it rapidly proceeded to afford poly(GPE) above the temperature. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3832–3840, 2001     

Stereospecific and molecular weight‐controlled polymerization of 1,3‐butadiene with Co(acac)3‐MAO catalyst

The polymerization of butadiene (Bd) with Co(acac)₃ in combination with methylaluminoxane (MAO) was investigated. The polymerization of Bd with Co(acac)₃‐MAO catalysts proceeded to give cis‐1,4 polymers (94 – 97%) bearing high molecular weights (40 × 10⁴) with relatively narrow molecular weight distributions (M_w's/M_n's). The molecular weight of the polymers increased linearly with the polymer yield, and the line passed through an original point. The polydispersities of the polymers kept almost constant during reaction time. This indicates that the microstructure and molecular weight of the polymers can be controlled in the polymerization of Bd with the Co(acac)₃‐MAO catalyst. The effects of reaction temperature, Bd concentration, and the MAO/Co molar ratio on the cis‐1,4 microstructure and high molecular weight polymer in the polymerization of Bd with Co(acac)₃‐MAO catalyst were observed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2793–2798, 2001     

Synthesis of phosphate‐pendant polymers and their application to thermally latent polymeric initiators

A novel phosphate monomer, O‐p‐(methacryloyloxymethyl)benzyl O,O‐diethyl phosphate (MDP) was synthesized by the reaction of diethyl phosphorochloridate with 1,4‐benzenedimethanol, followed by the reaction with methacryloyl chloride in the presence of triethylamine. The radical polymerization of MDP and copolymerization with methyl methacrylate were carried out in the presence of 2,2′‐azobisisobutyronitrile (3 mol %) in dimethylacetamide at 60 °C for 20 h to afford phosphate‐pendant polymers. The polymerization of glycidyl phenyl ether (GPE) was carried out with the phosphate‐pendant polymer as an initiator in the presence of ZnCl₂. The polymerization did not proceed below 90 °C but rapidly proceeded above 90 °C to afford polyGPE. The phosphate‐pendant polymer served as a good thermally latent polymeric initiator. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3365–3370, 2001     

Multiple melting and crystallization of nylon‐66/montmorillonite nanocomposites

Nylon‐66 nanocomposites were prepared by melt‐compounding nylon‐66 with organically modified montmorillonite (MMT). The organic MMT layers were exfoliated in a nylon‐66 matrix as confirmed by wide‐angle X‐ray diffraction (WAXD) and transmission electron microscopy. The presence of MMT layers increased the crystallization temperature of nylon‐66 because of the heterogeneous nucleation of MMT. Multiple melting behavior was observed in the nylon‐66/MMT nanocomposites, and the MMT layers induced the formation of form II spherulites of nylon‐66. The crystallite sizes L₁₀₀ and L₀₁₀ of nylon‐66, determined by WAXD, decreased with an increasing MMT content. High‐temperature WAXD was performed to determine the Brill transition in the nylon‐66/MMT nanocomposites. Polarized optical microscopy demonstrated that the dimension of nylon‐66 spherulites decreased because of the effect of the MMT layers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2861–2869, 2003     

Synthesis of ultrahigh molecular weight poly(N‐vinylcarbazole) with a high yield using low‐temperature heterogeneous‐solution polymerization

To prepare ultrahigh molecular weight (UHMW) poly(N‐vinylcarbazole) (PVCZ) with a high conversion, I heterogeneous‐solution‐polymerized N‐vinylcarbazole (VCZ) in methanol/tertiary butyl alcohol (TBA) at 25, 35, and 45 °C with a low‐temperature initiator, 2,2′‐azobis(2,4‐dimethylvaleronitrile) (ADMVN), and I investigated the effects of the polymerization conditions on the polymerization behavior and molecular parameters of PVCZ. A low‐polymerization temperature with ADMVN, a heterogeneous system with methanol, and a low chain transfer with TBA proved to be successful in obtaining PVCZ of UHMW [weight‐average molecular weight (M_w) > 3,000,000] and high conversion (>80%) with a smaller temperature rise during polymerization but still of free‐radical polymerization by an azoinitiator. The polymerization rate of VCZ in methanol/TBA at 25 °C was proportional to the 0.97 power of the ADMVN concentration, indicating a heterogeneous nature for the polymerization. The molecular weight was higher and the molecular weight distribution was narrower with PVCZ polymerized at lower temperatures. For PVCZ produced in methanol/TBA at 25 °C with an ADMVN concentration of 0.0001 mol/mol of VCZ, an M_w of 3,230,000 was obtained, with a polydispersity index of 2.4. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 539–545, 2001     

Synthesis and properties of novel polyimide/nylon‐6 triblock copolymers

Nylon‐6‐b‐polyimide‐b‐nylon‐6 copolymers were prepared by first synthesizing a series of imide oligomers end‐capped with phenyl 4‐aminobenzoate. The oligomers were then used to activate the anionic polymerization of molten ϵ‐caprolactam. In the block copolymer syntheses, the phenyl ester groups reacted quickly with caprolactam anions at 120 °C to generate N‐acyllactam moieties, which activated the anionic polymerization. In essence, nylon‐6 chains grew from the oligomer chain ends. All of the block copolymers had higher moduli and tensile strengths than those of nylon‐6. However, their elongations at break were much lower. The thermal stability, chemical resistance, moisture resistance, and impact strength were dramatically increased by the incorporation of only 5 wt % polyimide in the block copolymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4247–4257, 2000     

Alkoxyamine‐mediated “living” radical polymerization: MS investigation of the early stages of styrene polymerization initiated by cumyl‐TEISO

A new series of 1,1,3,3‐tetraethylisoindoline‐2‐oxyl (TEISO)‐based alkoxyamines was prepared. The half‐lives for thermal dissociation indicated that the most sterically congested cumyl‐TEISO alkoxymine had the greatest potential as an initiator for the polymerization of monomers at lower temperatures. The polymerization of styrene at 110 °C gave a linear evolution of M_n with conversion in the early stages. Further evidence for the “living” nature was given by the polydispersities of the polymers that remained low (M_w/M_n = 1.13–1.27) throughout the polymerization (up to 80% conversion). No polymer was formed for the styrene system in a reasonable time below 100 °C. High‐performance liquid chromatographic/mass spectrometric investigations of the distribution of trapped oligomers containing one to nine monomer units formed at 60 °C revealed that the trapping of oligomeric cumyl–styryl radicals by TEISO is irreversible at this temperature. Methyl methacrylate polymerized with cumyl‐TEISO at 60–70 °C, although the initial high rates of polymerization soon decreased to zero at low conversions (10–15%), and the high polydispersities (M_w/M_n = 1.42–1.73) indicated significant side reactions. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1232–1241, 2001     

Kinetics of the microemulsion polymerization of styrene with short‐chain alcohols as the cosurfactant

The kinetics of styrene microemulsion polymerization stabilized by sodium dodecyl sulfate (SDS) and a series of short‐chain alcohols (n‐C_iH_2i+1OH, abbreviated as C_iOH, where i = 4, 5, or 6) at 60 °C was investigated. Sodium persulfate was used as the initiator. The microemulsion polymerization process can be divided into two intervals: the polymerization rate (R_p) first increases to a maximum at about a 20% conversion (interval I) and thereafter continues to decrease toward the end of the polymerization (interval II). For all the SDS/C_iOH‐stabilized polymerization systems, R_p increases when the initiator or monomer concentration increases. The average number of free radicals per particle is smaller than 0.5. The molecular weight of the polymer produced is primarily controlled by the chain‐transfer reaction. In general, the reaction kinetics for the polymerization system with C₄OH as the cosurfactant behaves quite differently from the kinetics of the C₅OH and C₆OH counterparts. This is closely related to the different water solubilities of these short‐chain alcohols and the different concentrations of the cosurfactants used in the preparation of the microemulsion. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 898–912, 2001     

Emulsion copolymerization of D,L‐lactide and glycolide in supercritical carbon dioxide

Biodegradable polyesters were synthesized via an emulsion polymerization in supercritical carbon dioxide (SC‐CO₂). Copolymers of lactide and glycolide were synthesized in SC‐CO₂ with stannous octoate as the ring‐opening catalyst and a fluorocarbon polymer surfactant as an emulsifying agent. The conversion of lactide and glycolide was monitored with respect to the reaction time and temperature with ¹H NMR spectroscopy. The conversion of glycolide surpassed 99% within 72 h for an SC‐CO₂ phase maintained at 200 bar and 70 °C. Under the same conditions, lactide conversion reached 65% after 72 h of polymerization. Unpolymerized monomer was removed after the reaction by extraction with an SC‐CO₂ mobile phase. The molecular weights of all the copolymers were measured by gel permeation chromatography. Weight‐average molecular weights (M_w) ranged between 2500 and 30,200 g/mol and polydispersity indices ranged from 1.4 to 2.3 for polymerization times of 6 and 48 h, respectively. Although the molecular weight increased significantly during the first 48 h of reaction, there was no significant difference in the M_w for polymerization times of 48 and 72 h. Emulsion polymerization within the benign solvent SC‐CO₂ demonstrated improved conversion and molecular weight versus polymers synthesized without surfactant. The emulsion polymerization of lactide and glycolide copolymers in SC‐CO₂ is proposed as a novel production technique for high‐purity, biodegradable polymers. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 562–570, 2001     

Reverse atom transfer radical polymerization of methyl methacrylate with a new catalytic system,FeCl3/isophthalic acid

A new catalytic system, FeCl₃/isophthalic acid, was successfully used in the reverse atom transfer radical polymerization (RATRP) of methyl methacrylate (MMA) in the presence of a conventional radical initiator, 2,2′‐azo‐bis‐isobutyrontrile. Well‐defined poly(methyl methacrylate) (PMMA) was synthesized in an N,N‐dimethylformamide solvent at 90–120 °C. The polymerization was controlled up to a molecular weight of 50,000, and the polydispersity index was 1.4. Chain extension was performed to confirm the living nature of the polymer. The kinetics of the RATRP of MMA with FeCl₃/isophthalic acid as the catalyst system was investigated. The apparent activation energy was 10.47 kcal/mol. The presence of the end chloride atom on the resulting PMMA was demonstrated by ¹H NMR spectroscopy. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 765–774, 2001     

Vinyl polymerization with a binary system of p‐chlorobenzenediazonium salt and sodium tetraphenylborate

A combined system of sodium tetraphenylborate (STPB) and p‐chlorobenzenediazonium tetrafluoroborate (CDF) serves as an effective initiator at low temperatures for acrylate monomers such as methyl methacrylate (MMA), ethyl acrylate, and di‐2‐ethylhexyl itaconate. The polymerization of MMA with the STPB/CDF system has been kinetically investigated in acetone. The polymerization shows a low overall activation energy of 60.3 kJ/mol. The polymerization rate (R_p) at 40 °C is given by R_p = k[STPB/CDF]^0.5[MMA]^1.6, when the molar ratio of STPB to CDF is kept constant at unity, suggesting that STPB and CDF form a complex with a large stability constant and play an important role in initiation and that MMA participates in the initiation process. From the results of a spin trapping study, p‐chlorophenyl and phenyl radicals are presumed to be generated in the polymerization system. A plausible initiation mechanism is proposed on the basis of kinetic and electron spin resonance results. A large solvent effect on the polymerization can be observed. The largest R_p value in dimethyl sulfoxide is 11 times the smallest value in N,N‐dimethylformamide. The copolymerization of MMA and styrene with the STPB/CDF system gives results somewhat different from those of conventional radical copolymerization. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4206–4213, 2001     

Correlation between local mobility and mechanical properties of high‐speed melt‐spun nylon‐6 fibers

This article establishes the processing–microstructure–motion–property relationship of high‐speed melt‐spun nylon‐6 fibers. From solid‐state ¹H NMR T_1ρ (spin–lattice relaxation time in the rotating frame) relaxation studies, all nylon‐6 fibers spun at 4500–6100 m/min showed three‐component exponential decay with the time constants T_1ρ,I, T_1ρ,II, and T_1ρ,III, indicating that there existed three different motional phases. These phases were assigned to immobile crystalline, intermediate rigid amorphous, and mobile amorphous regions. The determination of the correlation time (τ_c) of the respective phases provided information about the local molecular mobility of each phase with respect to the spinning speed. As the spinning speed increased, τ_c of the crystalline region increased (4500–5200 m/min) and then reached a plateau. However, τ_c for the rigid amorphous region increased from 5200 m/min onward, indicating that the rigid amorphous chains were more oriented and constrained in the spinning speed range of 5500–6100 m/min. The drastic increase of the maximum thermal stress for all fibers from 5500 to 6100 m/min was coincident with the τ_c characteristics of the rigid amorphous region. The significant increase in tenacity and Young's modulus and the large decrease in elongation at break at 5500–6100 m/min were also in good agreement with the local molecular motion of the intermediate rigid amorphous phase in the nylon‐6 fibers. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 993–1000, 2001     

Synthesis,rheology, and morphology of nylon‐11/layered silicate nanocomposite

Exfoliated nylon‐11/layered silicate nanocomposites were prepared via in situ polymerization by dispersing organoclay in 11‐aminoundecanoic acid monomer. The original clay was modified by a novel method with 11‐aminoundecanoic acid. In situ Fourier transform infrared spectroscopy results show that stronger hydrogen bonds exist between nylon‐11 and organoclay than that of between nylon‐11 and original clay. The linear dynamic viscoelasticity of organoclay nanocomposites was investigated. Before taking rheological measurements, the exfoliated and intercalating structures and the thermal properties were characterized using X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry, and thermogravimetric analysis. The results show that the clay was uniformly distributed in nylon‐11 matrix during in situ polymerization of clay with 4 wt % or less. The presence of clay in nylon‐11 matrix increased the crystallization temperature and the thermal stability of nanocomposites prepared. Rheological properties such as storage modulus, loss modulus, and relative viscosity have close relationship with the dispersion favorably compatible with the organically modified clay. Comparing with neat nylon‐11, the nanocomposites show much higher dynamic modulus and stronger shear thinning behavior. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2161–2172, 2006     

Molecular structure determination of Ni(II) diimine complex and DMA analysis of Ni(II) diimine‐based polyethenes

Dynamic mechanical thermoanalysis showed that polyethene, prepared under suitable polymerization conditions with the Brookhart‐type catalyst dibromo‐N,N′‐1,2‐acenaphthylenediylidenebis[2,6‐bis(1‐methylethyl)benzeneamine]Ni(II)/methylaluminoxane (MAO), behaved like an elastomer, even though no comonomer was added. A structural characterization showed that the polymers contained methyl to hexyl branches and some longer branches. The effect of the polymerization conditions on branching was investigated through variations in the pressure and temperature of the polymerization. Depending on the degree and type of branching, polyethene was either quite amorphous or highly crystalline with a high melting temperature. The solid‐state structure of the catalyst dibromo‐N,N′‐1,2‐acenaphthylenediylidenebis[2,6‐bis(1‐methylethyl)benzeneamine]Ni(II) consisted of two centrosymmetrically related monomeric moieties, where Ni atoms were bridged by two bromide ligands. The Ni atom was five‐coordinated, with a square pyramidal coordination polyhedron. The sixth coordination site of the octahedral geometry was effectively blocked by the isopropyl groups of the 2,6‐C₆H₃(i‐Pr) substituents of the diimine ligand. In solution in the presence of MAO, the longer bridging Ni? Br bonds broke, and the complex dissociated to a monomeric species. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1426–1434, 2001     

Study of hydrogen bonding and thermal properties of polybenzoxazine and poly‐(ε‐caprolactone) blends

The thermal properties of physical blends containing benzoxazine monomer and polycaprolactone (PCL) were monitored by DSC and Fourier transform infrared spectroscopy (FTIR). The ring‐opening reaction and subsequent polymerization reaction of the benzoxazine were facilitated significantly by the presence of a PCL modifier. Hydrogen‐bond formation between the hydroxyl groups of polybenzoxazine and the carbonyl groups of PCL was evident from the FTIR spectra. Only one glass‐transition temperture (T_g) value was found in the composition range investigated, and the T_g value of the resulting blend appeared to be higher in the blend with a greater amount of PCL. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 736–749, 2001     

Synthesis and properties of poly‐(2‐ethynylpyridinium bromide) having propargyl side chains

Poly‐(2‐ethynylpyridinum bromide) (PEPBP) having propargyl side chains was prepared by the direct polymerization of 2‐ethynylpyridine and propargyl bromide under mild reaction conditions without any initiator and catalysts. The polymerization proceeded well to give PEPBP with propargyl side chains in relatively high yields. Various spectral data for the polymer structure indicated that the conjugated polymer system having N‐propargylpyridinum substituent was formed. This ionic polymer was completely soluble in water, methanol, dimethylformamide, dimethyl sulfoxide, and N,N‐dimethylacetamide and well processable into thin homogeneous film. The photoluminescence intensity (λ_max = 760 nm) of this polymer increased as the temperature was increased. At 1 KHz and room temperature, this polymer has k′ = 2.9 and σ = 7.3 × 10^?10 (S/cm). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3151–3158, 2001