Structure–property co‐relationship of fluorinated poly(imide‐siloxane)s

Eight poly(imide‐siloxane)s co‐polymers have been prepared by one pot solution imidization method. The polymers are synthesized by the reaction of bisphenol‐A‐dianhydride (BPADA) with fluorinated diamine 4,4′‐bis(3″‐trifluoromethyl‐p‐aminobiphenyl ether) biphenyl, and aminopropyl‐terminated polydimethylsiloxane (APPS). The polymers are synthesized by varying the siloxane loading to 5, 10, 15, 20, 25, 30, 35, and 40 wt%, respectively. Thermal, mechanical, rheological, and dielectric properties of these polymers have been evaluated with respect to siloxane loading. The polymers showed glass transition temperature of 107–203°C and tensile strength at break of 24–75 MPa depending on siloxane loading. The elongation break of the polymers ranges from 24 to 144% depending on siloxane loading. The amounts of char residue in the polymers have been correlated with incorporated siloxane in the polymer by NMR techniques. The polymers showed very low water absorption and dielectric constant as low as 2.43 when the siloxane loading is 40 wt%. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and properties of poly(imide‐hydrazide)s and poly(amide‐imide‐hydrazide)s from N‐[p‐(or m‐)carboxyphenyl]trimellitimide and aromatic dihydrazides or p‐aminobenzhydrazide via the phosphorylation reaction

A series of new poly(imide‐hydrazide)s and poly(amide‐imide‐hydrazide)s were obtained by the direct polycondensation of N‐[p‐(or m‐)carboxyphenyl]trimellitimide (p‐ or m‐CPTMI) with terephthalic dihydrazide (TPH), isophthalic dihydrazide (IPH), and p‐aminobenzhydrazide (p‐ABH) by means of diphenyl phosphite and pyridine in the N‐methyl‐2‐pyrrolidone (NMP) solutions containing dissolved CaCl₂. The resulting hydrazide‐containing polymers exhibited inherent viscosities in the 0.15–0.96 dL/g range. Except for that derived from p‐CPTMI with TPH or p‐ABH, the other hydrazide copolymers were readily soluble in polar solvents such as NMP and dimethyl sulfoxide (DMSO). As evidenced by X‐ray diffraction patterns, the hydrazide copolymer obtained from TPH showed a moderate level of crystallinity, whereas the others were amorphous in nature. Most of the amorphous hydrazide copolymers formed flexible and tough films by solvent casting. The amorphous hydrazide copolymers had glass‐transition temperatures (T_g) between 187 and 233 °C. All hydrazide copolymers could be thermally converted into the corresponding oxadiazole copolymers approximately in the region of 250–400 °C, as evidenced by the DSC thermograms. The oxadiazole copolymers showed a significantly decreased solubility when compared to their respective hydrazide precursors. They exhibited T_g's of 264–302 °C and did not show dramatic weight loss before 400 °C in air or nitrogen. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1599–1608, 2000     

Preparation and properties of poly(N‐isopropylacrylamide)/poly(N‐isopropylacrylamide) interpenetrating polymer networks for drug delivery

A novel poly(N‐isopropylacrylamide) (PNIPA)/PNIPA interpenetrating polymer network (IPN) was synthesized and characterized. In comparison with conventional PNIPA hydrogels, the shrinking rate of the IPN hydrogel increased when gels, swollen at 20 °C, were immersed in 50 °C water. The phase‐transition temperature of the IPN gel remained unchangeable because of the same chemical constituent in the PNIPA gel. The reswelling kinetics were slower than those of the PNIPA hydrogel because of the higher crosslinking density of the IPN hydrogel. The IPN hydrogel had better mechanical strength because of its higher crosslinking density and polymer volume fraction. The release behavior of 5‐fluorouracil (5‐Fu) from the IPN hydrogel showed that, at a lower temperature, the release of 5‐Fu was controlled by the diffusion of water molecules in the gel network. At a higher temperature, 5‐Fu inside the gel could not diffuse into the medium after a burst release caused by the release of the drug on the surface of the gel. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1249–1254, 2004     

Poly(urethane‐co‐benzoxazine)s via reaction of phenol terminated urethane prepolymers and benzoxazine monomer and investigation of their properties

In the present work, a new method was developed for the combination of polyurethanes (PUs) and polybenzoxazine (PBz) to obtain novel thermoset poly(urethane‐co‐benzoxazine)s with good thermal, mechanical, and electrical properties as well as low temperature curing profile. Knowing the catalytic effect of compounds possessing free phenolic groups on ring opening polymerization of benzoxazine monomers, preparation of phenol terminated urethane oligomers (PTPU) as the macroinitiator for a benzoxazine monomer (Ba) was considered. Firstly, NCO‐terminated urethane prepolymers were prepared from the reaction of poly(tetramethyleneether glycol), and 2,4‐tolylene diisocyanate, and then end functionalized with bisphenol‐A under proper condition. DSC, DMTA, and gel content measurements were applied to find optimum ring opening polymerization condition (170°C for 1 hr and 200°C for 15 min). Various kinds of thermoset polymers were prepared by the reaction of PTPU at different molecular weights with variable contents of Ba. All of monomeric and polymeric materials were characterized by conventional spectroscopic methods and their thermal, mechanical, viscoelastic, and electrical properties were measured and properties were correlated to their structure. Due to the interesting properties of these new materials, the possibility of using them as electrical insulators with higher service temperature in comparison to common PUs were examined and their potential applicability was confirmed. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis and characterization of poly(imide‐urethane) based on novel chain‐extender containing both imide and sulphone functions

Several new glycols containing both imide and sulfone groups, sulfonyl bisimide glycol (SBIG), were prepared from primary aromatic diamine, trimellitic anhydride and excess low molecular glycols. Then these SBIGs were used as chain extender to prepare a series of thermoplastic poly(imide‐urethane) (PIU), which introduced imide rings into the backbones. Compared to conventional linear polyurethane (PU), these PIUs exhibited better thermal stabilities because of the presence of the sulfone and built‐in imide groups. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4469–4477, 2005     

Cationic ring‐opening polymerization of novel 1,3‐dehydroadamantanes with various alkyl substituents: Synthesis of thermally stable poly(1,3‐adamantane)s

Cationic ring‐opening polymerizations of 5‐alkyl‐ or 5,7‐dialkyl‐1,3‐dehydroadamantanes, such as 5‐hexyl‐ ( 4 ), 5‐octyl‐ ( 5 ), 5‐butyl‐7‐isobutyl‐ ( 6 ), 5‐ethyl‐7‐hexyl‐ ( 7 ), and 5‐butyl‐7‐hexyl‐1,3‐dehydroadamantane ( 8 ), were carried out with super Brønsted acids, such as trifluoromethanesulfonic acid or trifluoromethanesulfonimide in CH₂Cl₂ or n‐heptane. The ring‐opening polymerizations of inverted carbon–carbon bonds in 4–8 proceeded to afford corresponding poly(1,3‐adamantane)s in good to quantitative yields. Poly( 4–8 )s possessing alkyl substituents were soluble in 1,2‐dichlorobenzene, although a nonsubstituted poly(1,3‐adamantane) was not soluble in any organic solvent. In particular, poly( 8 ) exhibited the highest molecular weight at around 7500 g mol^?1 and showed excellent solubility in common organic solvents, such as THF, CHCl₃, benzene, and hexane. The resulting poly( 4–8 )s containing adamantane‐1,3‐diyl linkages showed good thermal stability, and 10% weight loss temperatures (T₁₀) were observed over 400 °C. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4111–4124     

Synthesis and properties of novel soluble poly(amide‐imide)s with different pendant substituents

Two types of novel fluorinated diimide‐diacid monomers—[2,2′‐(4,4′‐(3′‐methylbiphenyl‐2,5‐diyl)bis(oxy)bis(3‐(trifluoromethyl)‐4,1‐phenylene))bis(1,3‐dioxoisoindoline‐5‐carboxylic acid)] (III) and [2,2′‐(4,4′‐(3′‐(trifluoromethyl)biphenyl‐2,5‐diyl)bis(oxy)bis(3‐(trifluoromethyl)‐4,1‐phenylene))bis(1,3‐dioxoisoindoline‐5‐carboxylic acid)] (IV)—were respectively designed and prepared by the condensation of diamines I and II with two molar equivalents of trimellitic anhydride. From both diimide‐diacids, two series of novel poly(amide‐imide)s (PAIs) (IIIa–IIIe and IVa–IVe) bearing different pendant groups were prepared by direct polymerization with various aromatic diamines (a–e). All the PAIs had a high glass transition temperatures (T_gs, 232–265 °C), excellent thermal stability (exhibiting only 5% weight loss at 493–542 °C under nitrogen) and good solubility in various organic solvents due to the introduction of the bulky pendant groups. The cast films of these PAIs (80–90 μm) had good optical transparency (73–81% at 450 nm, 85–88% at 550 nm and 87–89% at 800 nm) and low dielectric constants (2.65–2.98 at 1 MHz). The spin‐coated films of these PAIs presented a minimum birefringence value as low as 0.0077–0.0143 at 650 nm and low optical absorption at the near‐infrared optical communication wavelengths of 1310 and 1550 nm. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3243–3252     

Synthesis of thioether‐functional poly(olefin)s via ruthenium‐alkylidene initiated ring‐opening metathesis polymerization

Ring‐opening metathesis polymerization (ROMP) of thioether‐derived oxanorbornene imide ( M1 ) and its copolymerization with various cycloolefin comonomers such as cyclopentene ( M2 ), cyclopent‐3‐en‐1‐ol ( M3 ), cycloheptene ( M4 ), and cyclooctene ( M5 ) using Hoveyda–Grubbs second generation catalyst has been investigated. Polymerizations were performed at two different temperatures (0 and 25 °C) and the obtained functional poly(olefin)s were characterized by nuclear magnetic resonance ¹H and ¹³C (NMR), and infrared spectroscopy as well as size exclusion chromatography, differential scanning calorimetry, and thermogravimetric analysis analyses. Additionally, the dependence of the polymer composition on the reaction temperature and monomer feed was studied with time‐dependent ¹H NMR experiments. Copolymerization of M1 with a five‐membered cycloolefin monomer M2 showed relatively low ROMP reactivity irrespective of the reaction conditions in comparison to M3 , M4 , and M5 monomers. In general, the degree of monomer incorporation into poly(olefin)s were determined in the order of M5 > M3 > M4 > M2 , and that sheds light on the effect of cycloolefin ring strain energies in the ruthenium‐alkylidene initiated ROMP. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1741–1747     

Synthesis and characterization of conducting poly(aniline‐co‐o‐aminophenethyl alcohol)s

Poly(o‐aminophenethyl alcohol) and its copolymers containing the aniline unit were synthesized in aqueous hydrochloric acid medium by chemical oxidative polymerization. The chemical composition of these novel polymers was determined spectroscopically, and their viscosities were measured. These polymers exhibit good solubility in organic solvents that is attributed mainly to the polar hydroxyethyl side groups. Their structures (chain conformation and morphological structure) and properties (conductivity, electrochemical characteristics, glass transition, and degradation behavior) were characterized and then interpreted on the basis of the chemical composition along with the electronic and steric hindrance effects associated with the hydroxyethyl side group. Overall, the side group has a significant effect on the polymerization and influences the structure, chain conformation, and properties of the resultant polymer. The poly(aniline‐co‐o‐aminophenethyl alcohol)s containing 20–40 mol % o‐aminophenethyl alcohol units are potential conducting materials for microelectronic and electromagnetic shielding applications because they are easier to process than polyaniline but retain its beneficial properties. These polymers can also be used as a functional conducting polymer intermediate owing to the reactivity of the side group. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 983–994, 2002     

Photoluminescent properties of poly(p‐phenylene vinylene thiophene‐co‐siloxane)

A new p‐phenylene–vinylene–thiophene‐based siloxane block copolymer has been synthesized. The copolymer consists of alternating rigid and flexible blocks. The rigid blocks are composed of phenylene–vinylene–thiophene‐based units, and the flexible blocks are derived from 1,3‐dialkyldisiloxane units. The former component acts as the chromophore, and allows fine tuning of band gap for blue‐light emission, while the latter imparts good solubility of the copolymer in organic solvents, and thus, should enhance processibility of the resulting copolymer. The thermal properties of the copolymer have been characterized by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The photoluminescence (PL) of the copolymer in solution and in cast film has been studied. The effects of concentration on the PL intensity of the new copolymer in polymer blends with poly(methyl methacrylate) (PMMA) and poly(vinyl carbazole) (PVK) have also been described. Efficient energy transfer from PVK to the new block copolymer in the blended film was observed. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1450–1456, 2000     

Synthesis of new poly(amide imide)s with (n‐alkyloxy)phenyloxy side branches

Two series of new poly(amide imide)s having (n‐alkyoxy)phenyloxy side branches with various lengths, poly{p‐phenyleneiminoterephthaloylimino‐p‐phenylene[3,6‐di(n‐alkyloxy)phenyloxy]pyromellitimide}s ( PC _m TA s, m = 4, 8, 12) and poly{p‐phenyleneiminosebacoylimino‐p‐phenylene[3,6‐di(n‐alkyloxy)‐phenyloxy]‐ pyromellitimide}s ( PC _m SeA s, m = 4, 8, 12), were prepared by condensation of terephthalamide‐N,N′‐4,4′‐dianiline ( TA ) and sebacamide‐N,N′‐4,4′‐dianiline ( SeA ) with 3,6‐di[4‐(n‐alkyloxy)phenyloxy]pyromellitic dianhydrides , respectively. The inherent viscosities of the polymers were in the 0.82–1.20 dL/g range. The polymers were highly soluble in N‐methylpyrolidinone (NMP), even at room temperature and soluble in other polar aprotic solvents on heating. The PC _m TA s, which have aromatic backbones, were thermally more stable (431–442 °C) than the PC _m SeA s, which have an octamethylene unit in the main chain (407–409 °C). Degradation of weight up to 900 °C corresponded with the loss of side chain contents. The PC _m TA s exhibited no phase transition, whereas two endothermic peaks were observed for each of the PC _m SeA s. Wide‐angle X‐ray diffractometer investigations revealed that both polymers are amorphous and the n‐alkyloxy side chains are present in a layered structure. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3818–3825, 2001     

Novel method for the preparation of poly(urethane–imide)s and their properties

A polymer blend consisting of polyimide (PI) and polyurethane (PU) was prepared by means of a novel approach. PU prepolymer was prepared by the reaction of polyester polyol and 2,4-tolylenediisocyanate (2,4-TDI) and then end-capped with phenol. Poly(amide acid) was prepared from pyromellitic dianhydride (PMDA) and oxydianiline (ODA). A series of oligo(amide acid)s were also prepared by controlling the molar ratio of PMDA and ODA. The PU prepolymer and poly(amide acid) or oligo(amide acid) solution were blended at room temperature in various weight ratios. The cast films were obtained from the blend solution and treated at various temperatures. With the increase of polyurethane component, the films changed from plastic to brittle and then to elastic. The poly(urethane–imide) elastomers showed excellent mechanical properties and moderate thermal stability. The elongation of films with elasticity was more than 300%. The elongation set after the breaking of films was small. From the dynamic mechanical analysis, all the samples showed a glass transition temperature (T_g) at ca. −15°C, corresponding to T_g of the urethane component, suggesting that phase separation occurred between the two polymer components, irrespective of polyimide content. TGA and DSC studies indicated that the thermal degradation of poly(urethane–imide) was in the temperature range 250–270°C. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3745–3753, 1997     

Novel poly(N‐isopropylacrylamide)/clay/poly(acrylamide) IPN hydrogels with the response rate and drug release controlled by clay content

Novel interpenetrating network (IPN) hydrogels (PNIPAAm/clay/PAAm hydrogels) based on poly(N‐isopropylacrylamide) (PNIPAAm) crosslinked by inorganic clay and poly(acrylamide) (PAAm) crosslinked by organic crosslinker were prepared in situ by ultraviolet (UV) irradiation polymerization. The effects of clay content on temperature dependence of equilibrium swelling ratio, deswelling behavior, thermal behavior, and the interior morphology of resultant IPN hydrogels were investigated with the help of Fourier transform infrared spectroscopy, differential scanning calorimeter (DSC), scanning electron microscope (SEM). Study on temperature dependence of equilibrium swelling ratio showed that all IPN hydrogels exhibited temperature‐sensitivity. DSC further revealed that the temperature‐sensitivity was weakened with increasing amount of clay. Study on deswelling behavior revealed that IPN hydrogels had much faster response rate when comparing with PNIPAAm/clay hydrogels, and the response rate of IPN hydrogels could be controlled by clay content. SEM revealed that there existed difference in the interior morphology of IPN hydrogels between 20 [below lower critical solution temperature (LCST)] and 50 °C (above LCST), and this difference would become obvious with a decrease in clay content. For the standpoint of applications, oscillating swelling/deswelling behavior was investigated to determine whether properties of IPN hydrogels would be stable for potential applications. Bovine serum albumin (BSA) was used as model drug for in vitro experiment, the release data suggested that the controlled drug release could be achieved by modulating clay content. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 96–106, 2009     

Synthesis and characterization of a vinyl‐terminated benzoxazine monomer and its blends with poly(ethylene oxide)

A vinyl‐terminated benzoxazine (VB‐a), which could be polymerized through ring‐opening polymerization, was synthesized through the Mannich condensation of bisphenol A, formaldehyde, and allylamine. This VB‐a monomer was then subjected to blending with poly(ethylene oxide) (PEO), followed by thermal curing, to form poly(VB‐a)/PEO blends. The specific interactions, miscibility, morphology, and thermal properties of these blends were investigated with Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry, dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). Before curing, we found that PEO was miscible with VB‐a, as evidenced by the existence of a single composition‐dependent glass transition temperature (T_g) for each composition. The FTIR spectra revealed the presence of hydrogen‐bonding interactions between the hydroxyl groups of poly(VB‐a) and the ether groups of PEO. Indeed, the ring‐opening reaction and subsequent polymerization of the benzoxazine were facilitated significantly by the presence of PEO. After curing, DMA results indicated that the 50/50 poly(VB‐a)/PEO blend exhibited two values of T_g: one broad peak appeared in the lower temperature region, whereas the other (at ca. 327 °C, in the higher temperature region) was higher than that of pristine poly(VB‐a) (301 °C). The presence of two glass transitions in the blend suggested that this blend system was only partially miscible. Moreover, SEM micrographs indicated that the poly(VB‐a)/PEO blends were heterogeneous. The volume fraction of PEO in the blends had a strong effect on the morphology. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 644–653, 2007     

Synthesis and characterization of poly[styrene‐b‐methyl(3,3,3‐trifluoropropyl)siloxane] diblock copolymers via anionic polymerization

A series of narrow molecular weight distribution (MWD) polystyrene‐b‐poly[methyl(3,3,3‐trifluoropropyl)siloxane] (PS‐b‐PMTFPS) diblock copolymers were synthesized by the sequential anionic polymerization of styrene and trans‐1,3,5‐trimethyl‐1,3,5‐tris(3′,3′,3′‐trifluoropropyl)cyclotrisiloxane in tetrahydrofuran (THF) with n‐butyllithium as the initiator. The diblock copolymers had narrow MWDs ranging from 1.06 to 1.20 and number‐average molecular weights ranging from 8.2 × 10³ to 37.1 × 10³. To investigate the properties of the copolymers, diblock copolymers with different weight fractions of poly[methyl(3,3,3‐trifluoropropyl)siloxane] (15.4–78.8 wt %) were prepared. The compositions of the diblock copolymers were calculated from the characteristic proton integrals of ¹H NMR spectra. For the anionic ring‐opening polymerization (ROP) of 1,3,5‐trimethyl‐1,3,5‐tris(3′,3′,3′‐trifluoropropyl)cyclotrisiloxane (F₃) initiated by polystyryllithium, high monomer concentrations could give high polymer yields and good control of MWDs when THF was used as the polymerization solvent. It was speculated that good control of the block copolymerization under the condition of high monomer concentrations was due to the slowdown of the anionic ROP rate of F₃ and the steric hindrance of the polystyrene precursors. There was enough time to terminate the ROP of F₃ when the polymer yield was high, and good control of block copolymerization could be achieved thereafter. The thermal properties (differential scanning calorimetry and thermogravimetric analysis) were also investigated for the PS‐b‐PMTFPS diblock copolymers. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4431–4438, 2005     

Structure and properties of cellulose/poly(N‐isopropylacrylamide) hydrogels prepared by IPN strategy

Interpenetrating polymer network (IPN) strategy was developed to fabricate novel hydrogels composed of cellulose and poly(N‐isopropylacrylamide) (PNIPAAm) with high mechanical strength and adjustable thermosensitivity. Cellulose hydrogels were prepared by chemically cross‐linking cellulose in NaOH/urea aqueous solution, which were employed as the first network. The second network was subsequently obtained by in situ polymerization/cross‐linking of N‐isopropylacrylamide in the cellulose hydrogels. The results from FTIR and solid ¹³C NMR indicated that the two networks co‐existed in the IPN hydrogels, which exhibited uniform porous structure, as a result of good compatibility. The mechanical and swelling properties of IPN hydrogels were strongly dependent on the weight ratio of two networks. Their temperature‐sensitive behaviors and deswelling kinetics were also discussed. This work created double network hydrogels, which combined the advantages of natural polymer and synthesized PNIPAAm collectively in one system, leading to the controllable temperature response and improvement in the physical properties. Copyright © 2009 John Wiley & Sons, Ltd.     

RAFT synthesis of a water‐soluble triblock copolymer of poly(styrenesulfonate)‐b‐poly(ethylene glycol)‐b‐poly(styrenesulfonate) using a macromolecular chain transfer agent in aqueous solution

Triblock copolymers of poly(styrenesulfonate)‐b‐poly(ethylene glycol)‐b‐poly(styrenesulfonate) with narrow molecular weight distribution (M_w/M_n = 1.28–1.40) and well‐defined structure have been synthesized in aqueous solution at 70 °C via reversible addition‐fragmentation chain transfer polymerization. Poly(ethylene glycol) (PEG) capped with 4‐cyanopentanoic acid dithiobenzoate end groups was used as the macro chain transfer agent (PEG macro‐CTA) for sole monomer sodium 4‐styrenesulfonate. The reaction was controllable and displayed living polymerization characteristics and the triblock copolymer had designed molecular weight. The reaction rate depended strongly on the CTA and initiator concentration ratio [CTA]₀/[ACPA]₀: an increase in [CTA]₀/[ACPA]₀ from 1.0 to 5.0 slowed down the polymerization rate and improved the molecular weight distribution with a prolonged induction time. The polymerization proceeded, following first‐order kinetics when [CTA]₀/[ACPA]₀ = 2.5 and 5.0. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3698–3706, 2007     

Synthesis and characterization of novel degradable photocrosslinked poly(ether‐anhydride) networks

New degradable poly(ether‐anhydride) networks were synthesized by UV photopolymerization. Dicarboxylated poly(ethylene glycol) (PEG) or poly(tetramethylene glycol) (PTMG) was reacted with an excess of methacrylic anhydride to form dimethacrylated macromers containing anhydride linkages. The percent of conversion for the macromer formation was more than 80% at 60 °C after 24 h. ¹H NMR and IR spectroscopies show the presence of anhydride linkages in the macromer. In vitro degradation studies were carried out at 37 °C in PBS with crosslinked polymer networks formed by UV irradiation. All PEG‐based polymers degraded within 2 days, while PTMG‐based polymers degraded by 50% of the initial weight after 14 days. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1277–1282, 2000     

Antimicrobial loading into and release from poly(ethylene glycol)/poly(acrylic acid) semi‐interpenetrating hydrogels

Electrostatic interactions within a semi‐interpenetrating network (semi‐IPN) gel can control the postsynthesis loading, long‐term retention, and subsequent release of small‐molecule cationic antibiotics. Here, electrostatic charge is introduced into an otherwise neutral gel [poly(ethylene glycol) (PEG)] by physically entrapping high‐molecular‐weight poly(acrylic acid) (PAA). The network structure is characterized by small‐angle neutron scattering. PEG/PAA semi‐IPN gels absorb over 40 times more antibiotic than PAA‐free PEG gels. Subsequent soaking in physiological buffer (pH 7.4; 0.15 M NaCl) releases the loaded antibiotics for periods as long as 30 days. The loaded gels elute antibiotics with diffusivities of 4.46 × 10^?8 cm²/s (amikacin) and 2.08 × 10^?8 cm²/s (colistin), which are two orders of magnitude less than those in pure PEG gels where diffusion is controlled purely by gel tortuosity. The release and hindered diffusion can be understood based on the partial shielding of the charged groups within the loaded gel, and they have a significant effect on the antimicrobial properties of these gels. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 64–72