Application of stress induces ascorbate peroxidases of S. polyrhiza for green-synthesis Cu nanoparticles

The objective of this study was to assess the effects of stress on physiology/biochemical component of S. polyrhiza and its impact on CuNPs synthesis and bioethanol production. NaCl with RV5 provokes oxidative stress in S. polyrhiza and significantly increase MAD, Proline, H₂O₂, ROS, SOD and APX activity compare to control condition. Starch accumulation in S. polyrhiza was found 354% higher and correspond 4.4 times higher ethanol yield under stress condition compare to control. CuNPs were synthesized with an average size of 23–26 nm by purified fraction of APX having 37 KDa MW, 1.44 IU specific activity. Synthesized CuNPs were stable up to 15 consecutive cycles and potency against wide range of reactive dyes. The maximum remedial efficiency of synthesized CuNPs for COD and BOD was 55263.3 ± 3298.5 mg/m³min. and 30560.3 ± 1987.5 mg/m³min. respectively for RV5 wastewater. 0.072 mg/g of bioethanol was produced from the wet pulp remaining after nanoparticles synthesis. High efficiency of CuNPs and significant production of Ethanol, indicate that the feasibility for circular model for continuous industrial wastewater treatment.     

Optimization of inoculum to substrate ratio for enhanced methane yield from leather fleshings in a batch study

One of the most significant issues of the last few decades has been tracing for renewable energy sources. Animal fleshing (ANFL) is the most common proteinaceous solid waste accured during the production of leather and it must be disposed of in an environmentally responsible manner. This paper is attempts to assess the biogas production from solid waste originating from the chrome based tannery. Anaerobic digestion of these wastes will be a viable option for waste stabilization and energy production in the form of biogas to be utilized in the industry. The bio-methane potential of the wastes were examined by mixing these wastes with various sources of inoculum and different inoculum to substrate (I/S) ratio considered. The batch experiments were carried out in 2.5 l glass reactors with a various source of inoculumviz., Cow Dung (CD), Elephant Dung (ED) and Bio-Digested Slurry (BDS) with varied inoculum to substrate (LFs) ratios for a retention time of 50 days with replications. The results obtained from the experiments showed that BDS:LF (25:75) had the highest gas production of 14505 ml (651.85 ml CH₄g^?1 VS) followed by CD:LF (50:50) produced 12072.5 ml (789.36 ml CH₄g^?1 VS) and ED:LF (75:25) produced 11252.5 ml (1492.08 ml CH₄g^?1 VS)with a methane content of 63.77, 61.92 and 62.72%, respectively.     

Cyclometalated complexes containing ferrocenyl Schiff base: Preparation,characterization, DFT calculations,application in cancer and biological researches and MOE studies

A series of transition metal (II/III) complexes containing organometallic Schiff base ligand (H₂L) had been synthesized and characterized by using elemental analysis (C, H, N, M), molar conductivity, IR, UV–Vis, ¹H NMR and mass spectral analysis. Also, their TG and DTG behaviors were investigated. The ligand was prepared by condensation of 4-aminosalicylic acid with 2-acetylferrocene in 1:1 M ratio. The data of elemental analysis indicated that the prepared complexes were synthesized also in a 1:1 M ratio. The ligand behaved as neutral bidentate ligand that coordinated to metal ions through protonated O-phenolic and protonated carboxylic-OH groups. All complexes had octahedral structure. DFT calculations for H₂L ligand were determined with some parameters such as HOMO-LUMO energy gab, electronegativity and chemical hardness–softness. Antimicrobial activity of both H₂L Schiff base ligand and its metal complexes was tested against different strains of bacteria and fungi species. Furthermore, all compounds had been screened for their anticancer activities against breast cancer (MCF-7) cell line. [Cu(H₂L)(H₂O)₂Cl₂]·2H₂O complex had the lowest IC₅₀ value = 47.3 µg/mL. For determining the more effective and probable binding mode between the H₂L ligand, Co(II) and Zn(II) complexes with different active sites of 4K3V, 2YLB and 3DJD receptors, so molecular docking studies were investigated.     

Fractionation and purification of antioxidant peptides from Chinese sturgeon (Acipenser sinensis) protein hydrolysates prepared using papain and alcalase 2.4L

Protein hydrolysates have the potential to be natural and safer sources of bioactive peptides. In this study, two proteases were used to hydrolyze Chinese sturgeon (Acipenser sinensis) protein, and the hydrolysates were then purified to yield antioxidant peptides. The degree of hydrolysis of 23.56 % and 18.14 % was obtained using papain and alcalase 2.4L, respectivly, and hydrolysates had 96.80 % and 87.24 % total amino acid content, respectivly. The papain hydrolysate (PH) and alcalase 2.4L hydrolysate (AH) showed good antioxidant activity against DPPH^? (IC₅₀ of 3.64 and 3.15 mg/mL) and ABTS^?+ (IC₅₀ of 1.92 and 1.58 mg/mL), respectively. The low-molecular-weight (<1000 Da) fraction of both hydrolysates demonstrated the highest antiradical activity (IC₅₀ of 2.59 and 2.31 mg/mL, DPPH) and (IC₅₀ of 1.54 and 1.36 mg/mL, ABTS), respectively. Nine peptides were separated from both hydrolysates using reverse phase high performance liquid chromatography (RP-HPLC). The IC₅₀ for ABTS^?+ scavenging activity of peptide P5 with valine, glycine and asparagine (MW of 282.13 Da) from PH, and peptide P3 with histidine, glycine and alanine (MW of 302.74 Da) from AH was 0.89 and 0.72 mg/mL, respectively. The fractions and purified peptides obtained from Chinese sturgeon hydrolysates could be utilized as natural antioxidant substitutes in pharmaceuticals and food products.     

Developments on carbon dioxide reduction: Their promise,achievements, and challenges

CO₂ reduction processes continue to be developed for electrosynthesis, energy storage applications, and environmental remediation. A number of promising materials have shown high activity and selectivity to target reduction products. However, the progress has been mainly at a small laboratory scale, and the technical challenges of large scale CO₂ reduction have not been considered adequately. This review covers recent advancements in catalyst materials and cell designs. The leading materials for CO₂ reduction to a number of useful products are presented with their corresponding cell and reactor designs. The latest efforts to progress to industrially relevant scales are discussed, along with the challenges that must be met for carbon dioxide reduction to be a viable route for mass scale production.     

Semisynthetic derivatives of haemanthamine and their in vitro antiproliferative activity evaluation against a panel of human cell lines

In this study, a new series of aliphatic, cyclic, and heterocyclic derivatives of haemanthamine was designed and synthesized to enhance its inhibitory effect on the proliferation and viability of cancer cells. A library of haemanthamine derivatives was subjected to 10 μM single-dose cytotoxicity screening against a panel of human cell lines of various histotypes. Initial cytotoxicity evaluation of the parent haemanthamine (1) and a series of twenty-nine (2–30) semisynthetic analogues showed that for some of the newly formed derivatives, a certain cytotoxic effect was observed, in one case even higher than that of the parent compound. Specifically, 11-O-(4-chloro-3-nitrobenzoyl)haemanthamine (21) showed an enhanced antiproliferative effect, where the mean growth percent (GP) value was 5% compared to haemanthamine, leading to a decrease in the GP to 25%. Among ten cell lines tested, derivative 21, bearing a substituted aromatic ester bond via C-11 of haemanthamine, had excellent activity for inhibiting the growth of HeLa (IC₅₀ = 0.2 ± 0.1 μM), A549 (IC₅₀ = 1.7 ± 0.1 μM) and HT-29 (IC₅₀ = 2.2 ± 0.1 μM) cells. When evaluating response kinetics, we found that 21 and haemanthamine dose- and time-dependently suppressed the proliferation of A549 cells. In contrast to haemanthamine (1), Trypan blue and lactate dehydrogenase (LDH) release assay revealed that 21 was capable of reducing the survival of A549 cells.     

Photocatalytic and antifouling properties of TiO2-based photocatalytic membranes

Photocatalysis has been extensively studied due to its potential ability to avoid the excessive use of chemical reagents and reduce the energy consumption by employing solar energy. Moreover, to alleviate the reduction in the membrane permeation selectivity, separation efficiency, and membrane service life caused by the emerging micro-pollutants and membrane fouling, membrane technology is often coupled with microbial, electrochemical, and catalytic processes. However, although physical/chemical cleaning and membrane module replacement can overcome the inherent limitations caused by membrane fouling and other membrane separation processes, high operating costs limit their practical applications. In this review, common preparation methods for TiO₂ photocatalytic membranes are described in detail, and the main approaches to enhancing their photocatalytic performance are discussed. More importantly, the mechanism of the TiO₂ photocatalytic membrane antifouling process is elucidated, and some applications of photocatalytic membranes in other areas are described. This review systematically outlines future research directions in the field of photocatalytic membrane modification, including metal and non-metal doping, fabrication of heterojunction structures, control over reaction conditions, increase in hydrophilicity, and increase in membrane porosity.     

Ascorbic acid supported Carboxymethyl cellulose stabilized silver nanoparticles as optical nanoprobe for Au3+ detection in environmental sample

Heavy metals (HMs), pollution of major environmental matrices and its attendant effects on human health and the environment, continue to generate huge scientific interest, particularly in monitoring and detection. Herein, the optical property of carboxymethyl cellulose stabilized silver nanoparticles (CMC-AgNPs), supported with ascorbic acid, is exploited as a colorimetric probe for the detection of toxic Au³⁺ ion in solution. The as-synthesized CMC-AgNPs showed sharp absorption maximum at 403 nm, with sparkling yellow color and average particles size distribution less than 10 nm. It was further characterized using ATR-FTIR, TEM, FESEM/EDS, XRD and DLS/zeta potential analyzer. Au³⁺ ion detection strategy involves the addition of ascorbic acid (AA) to a pH adjusted CMC-AgNPs, followed by the analyte addition. AA would facilitate the reduction of Au³⁺ on CMC-AgNPs (seed), with resultant color perturbations from light yellow to yellow, orange, ruby red and purple red, under 8 min incubation, at room temperature (RT). The CMC-AgNPs could also serve as a catalyst, by promoting AA mediated reduction of Au³⁺, in-situ. Moreover, we propose, that the color and the absorption spectra change is attributed to the deposition of gold nanoparticles (AuNPs), on the CMC-AgNPs/AA probe, to form (CMC-Ag@Au) nanostructures, depending on the analyte concentration. Absorbance ratio (A₅₄₀/A₄₀₃) showed good linearity with Au³⁺ concentration from 0.25 to 100.0 µM, and an estimated LOD of 0.061 µM. The assay was applied to Au³⁺ detection in environmental wastewater sample, showing satisfactory real sample detection potentiality.     

Assessment of antioxidant and cytotoxic potential of silver nanoparticles synthesized from root extract of Reynoutria japonica Houtt

Free radicals, mostly consist of reactive oxygen species, are generated in human body by several exogenous and endogenous systems. Overproduction of free radicals is known to cause several degenerative disorders including cancer. The aim of this study is to synthesize silver nanoparticles (AgNPs) using root extract of Reynoutria japonica and to investigate its antioxidant and cytotoxic potential. AgNPs were synthesized by green approach and subsequently characterized using UV–vis spectroscopy, SEM, TEM, FTIR, XRD, EDS and DLS. The antioxidant activity was investigated using DPPH, FRAP, H₂O₂, and ABT?⁺ radical scavenging assays while the cytotoxic effect was assessed using different human cancer cell lines including lung (A549), liver (Hep-G2) and breast (MDA-MB-231) by MTS assay. Moreover, the specificity of NPs was assessed against two normal human cell lines e.g. alveolar and renal primary epithelial cells (HPAEpiC and HRPTEpiC). The UV–vis spectra confirmed the synthesis of AgNPs by producing a characteristic peak at 410 nm. Further analysis confirmed that AgNPs were crystalline in nature, predominantly spherical in shape, with an average width and area of 17.34 nm and 164.46 nm², respectively. DLS analysis revealed that NPs possess a high negative zeta potential value (?28.5 mV), thus facilitating its electrostatic stabilization. AgNPs showed dose dependent antioxidant activity against DPPH, FRAP, H₂O₂ and ABTS with IC₅₀ values 19.25, 22.45, 24.20 and 18.88 µg/ml, respectively. The AgNPs depicted significant cytotoxic effects against A549, Hep-G2 and MDA-MB-231 cell lines with IC₅₀ values of 4.5, 5.1 and 3.46 µg/ml, respectively. Moreover, the NPs exhibited highest selectivity index (>2.0) for A549, Hep-G2 and MDA-MB-231, confirming its specificity towards cancer cell lines. In conclusion, AgNPs prepared from root extract of R. japonica possess strong antioxidant and cytotoxic potential which suggests that they should be investigated further in order to develop safe and effective antioxidant and/or cytotoxic formulations.     

Effect of potassium permanganate on morphological,structural and electro-optical properties of graphene oxide thin films

This work investigated the effect of Potassium Permanganate (KMnO₄) on graphene oxide (GO) properties, especially on electrical properties. The GO thin films were deposited on a glass substrate using drop casting technique and were analysed by using various type of spectroscopy (e.g. Scanning Electron Microscopy (SEM), Ultra- Violet Visible (UV–VIS), Fourier Transform Infrared (FTIR), X-Ray Diffraction (XRD), optical band gap, Raman Spectroscopy). Furthermore, the electrical experiments were carried out by using current–voltage (I-V) characteristic. The GO thin film with 4.5 g of KMnO₄ resulted in higher conductivity which is 3.11 × 10^?4 S/cm while GO with 2.5 g and 3.5 g of KMnO₄ achieve 2.47 × 10^?9 S/cm and 1.07 × 10^?7 S/cm, respectively. This further affects the morphological (SEM), optical (band gap, UV–Vis, FTIR, and Raman), and crystalline structural (XRD) properties of the GO thin films. The morphological, elemental, optical, and structural data confirmed that the properties of GO is affected by different amount of KMnO₄ oxidizing agent, which revealed that GO can potentially be implemented for electrical and electronic devices.     

Eco-friendly synthesis of size-controlled silver nanoparticles by using Areca catechu nut aqueous extract and investigation of their potent antioxidant and anti-bacterial activities

Silver nanoparticles (AgNPs) have attracted considerable attention owing to their unique biological applications. AgNPs synthesized by plant extract is considered as a convenient, efficient and eco-friendly material. In this work, the aqueous extract of Areca catechu L. nut (ACN) was used as the reducing and capping agents for one-pot synthesis of AgNPs, and their antioxidant and antibacterial activities were investigated. UV (Ultra Violet)-visible spectrum and dynamic light scattering (DLS) analysis revealed that the size of AgNPs was sensitive to the synthesis conditions. The synthesized AgNPs were composed of well-dispersed particles with an small size of about 10 nm under the optimal conditions (pH value of extract was 12.0; AgNO₃ concentration was 1.0 mM; reaction time was 90 min). In addition, scanning electron microscope with energy dispersive X-ray (SEM-EDX), transmission electron microscopy (TEM) and X-ray diffraction (XRD) results further verified that the synthesized AgNPs had a stable and well-dispersed form (Zeta potential value of ?30.50 mV and polydispersity index of 0.328) and a regular spherical shape (average size of 15–20 nm). In addition, Fourier transform infrared spectrometry (FTIR) results revealed that phytochemical constituents in ACN aqueous extract accounted for Ag⁺ ion reduction, capping and stabilization of AgNPs. The possible reductants in the aqueous extract of Areca catechu L. nut were identified by high-performance liquid chromatography-electrospray ionization-quadrupole-time of flight-mass spectrometry (HPLC-ESI-qTOF/MS) method. More importantly, the synthesized AgNPs indicated excellent free radical scavenging activity of 1,1-diphenyl-2-picrylhydrazyl (DPPH, IC₅₀ = 11.75 ± 0.29 μg/mL) and 2,2-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) diammonium salt (ABTS⁺, IC₅₀ = 44.85 ± 0.37 μg/mL), which were significant higher than that of ascorbic acid. Moreover, AgNPs exhibited an enhanced antibacterial activity against six selected common pathogens (especially Escherichia coli and Staphylococcus aureus) compared with AgNO₃ solution. In a short, this study showed that the Areca catechu L. nut aqueous extract could be applied for eco-friendly synthesis of AgNPs.     

Influence of extractions on physicochemical characterization and bioactivity of Piper nigrum oils: Study on the non-isothermal decomposition kinetic

Black pepper oils have been investigated frequently in the recent years. However, there is a significant variation in physicochemical properties and bioactivity of oils depended on extraction techniques. In this study, the systemic investigation of four various extraction methods was performed to evaluate the physicochemical characterizations, antioxidant and antibacterial activity. The investigation of ¹H NMR, FTIR and UV–Vis spectra confirmed presence of non-volatile components in oils extracted through supercritical CO₂ and hexane-soaking extractions which induced their typical thermal properties. The isothermal behaviour of extracted oils related to evaporation was within range of 3.2–7.3% (w/w) at 27 °C. The SEM images of the black pepper confirmed different operation manners of mechanism between extractions using the solvents and heating process. The lowest MIC for both essential oils from conventional hidrodistillation and microwave-assisted hidrodistillation against two bacteria including E. coli and B. subtilis were found to be 137 µg mL⁻¹. The non-isothermal decomposition kinetics were investigated on the essential oil of microwave-assisted hydrodistillation extraction. The activation energies and pre-exponent factors of non-isothermal decomposition were found to be in range of 36.5–73.7 KJ mol⁻¹ and 4.98 × 10³–1.97 × 10⁸ s⁻¹, respectively, dependent on conversional fractions of the oil. The results revealed that chemical components, physicochemical properties and bioactivity of black pepper essential oils depended on the extraction techniques.     

A pH-response multifunctional nanoplatform based on NaGdF4:Yb,Er,Fe@Ce6@mSiO2-DOX for synergistic photodynamic/chemotherapy of cancer cells

Cancer is one of the major diseases that seriously threaten human health. Drug delivery nanoplatforms for tumor treatment have attracted increasing attention owing to their unique advantages such as good specificity and few side effects. This study aimed to fabricate a pH-responsive drug release multifunctional nanoplatform NaGdF₄:Yb,Er,Fe@Ce6@mSiO₂-DOX. In the platform, Fe³⁺ doping enhanced the fluorescence intensity of NaGdF₄:Yb, Er by 5.8 folds, and the mSiO₂ shell substantially increased the specific surface area of nanomaterials (559.257 m²/g). The loading rates of chlorin e6 and doxorubicin hydrochloride (DOX) on NaGdF₄:Yb,Er,Fe@Ce6@mSiO₂-DOX reached 28.58 ± 0.85% and 87.53 ± 5.53%, respectively. Additionally, the DOX release rate from the nanoplatform was only 24.4% after 72 h at pH 7.4. However, under tumor microenvironment conditions (pH 5.0), the release rate of DOX increased to 85.3% after 72 h. The nanoplatform could generate reactive oxygen species (ROS) under 980 nm near-infrared excitation. Moreover, the nanoplatform exhibited a strong comprehensive killing efficiency against cancer cells. The viabilities of HeLa, MCF-7, and HepG2 cancer cells were only 18.5, 11.4, and 9.3%, respectively, after being treated with a combination of photodynamic therapy and chemotherapy. The constructed nanoplatform exhibits great application potential in cancer treatment.     

Efficient synthesis of magnetic nanoparticle-Musa acuminata peel composite for the adsorption of anionic dye

The impregnation of magnetite (Mt) nanoparticle (NPs) onto Musa acuminata peel (MApe), to form a novel magnetic combo (MApe-Mt) for the adsorption of anionic bromophenol blue (BPB) was studied. The SEM, EDX, BET, XRD, FTIR and TGA were used to characterize the adsorbents. The FTIR showed that the OH and CO groups were the major sites for BPB uptake onto the adsorbent materials. The average Mt crystalline size on MApe-Mt was 21.13 nm. SEM analysis revealed that Mt NPs were agglomerated on the surface of the MApe biosorbent, with an average Mt diameter of 25.97 nm. After Mt impregnation, a decrease in BET surface area (14.89 to 3.80 m²/g) and an increase in pore diameter (2.25–3.11 nm), pore volume (0.0052–0.01418 cm³/g) and pH point of zero charge (6.4–7.2) was obtained. The presence of Pb(II) ions in solution significantly decreased the uptake of BPB onto both MApe (66.1–43.8%) and MApe-Mt (80.3–59.1%), compared to other competing ions (Zn(II), Cd(II), Ni(II)) in the solution. Isotherm modeling showed that the Freundlich model best fitted the adsorption data (R² > 0.994 and SSE < 0.0013). In addition, maximum monolayer uptake was enhanced from 6.04 to 8.12 mg/g after Mt impregnation. Kinetics were well described by the pseudo-first order and liquid film diffusion models. Thermodynamics revealed a physical, endothermic adsorption of BPB onto the adsorbents, with ΔH^o values of 15.87–16.49 kJ/mol, corroborated by high desorption (over 90%) of BPB from the loaded materials. The viability of the prepared adsorbents was also revealed in its reusability for BPB uptake.     

Green synthesis of copper oxide nanoparticles CuO NPs from Eucalyptus Globoulus leaf extract: Adsorption and design of experiments

The study is concerned with synthesizing copper oxide nanoparticles with leaf extract Eucalyptus Globoulus. The results of scanning electron microscopy (SEM) and dynamic light scattering (DLS) revealed that the green synthesized copper oxide nanoparticles are spherical and have a mean particle size of 88 nm, with a negative zeta potential of ?16.9 mV. The XRD graph showed the crystalline and monoclinic phases of CuO nanoparticles. The average crystalline size around 85.80 nm was observed by the Debye–Scherrer formula. The adsorption characteristics of the nano-adsorbents were investigated using methyl orange, and the adsorption efficiency at room temperature attained 95 mg/g. Copper oxide nanoparticles (CuO NPs) adsorb methyl orange dye most effectively at pH 4.5 when the dye is applied in quantities of 0.04 g/50 mL. Box–Behnken design (BBD) in response surface methodology (RSM) was used to optimize various process parameters, such as pH solution (X₁: 2 – 11), adsorbing dose (X₂: 0.01 – 0.08 g/L), [MO] dye concentration (X₃: 10 – 80 mg/L). Overall, the adjusted coefficient of determination (R²) value of 0.99 demonstrated that the used model was quite appropriate, and the chosen RSM was effective in optimization the decolorization conditions of MO.     

Shot noise sets the limit of quantification in electrochemical measurements

Detection of single molecules, particles, and rapid redox events is a challenge of electrochemical investigations and requires either an amplification strategy or significant averaging for the electrochemical current to exceed the noise level. We consider the minimum number of electrons required to reach the limit of quantification in these electrochemical measurements. A survey of the literature indicates that the state-of-the-art limit in current detection for different types of measurements (e.g. voltammetry, single-molecule redox cycling, ion channel recordings of single molecules, metal nanoparticle collision, and phase nucleation) is independent of the nature of the measurement and increases linearly with reciprocal response time, Δt^?1, over ～5 orders of magnitude (from ～10 to ～10⁶ s^?1). We demonstrate that the practical limit of quantification requires cumulative measurement of ～2100 electrons during Δt and is determined by statistics of counting electrons, that is, the shot noise in the current.     

Microwave-assisted extraction of high-molecular-weight hemicelluloses from spruce wood

Microwave-assisted extraction (MAE) at atmospheric pressure has been demonstrated as an efficient technology for the extraction of polymeric hemicelluloses from spruce sawdust. This technology was shown to be more efficient than conventional extraction. MAE leads to a high solubilization of wood and a selective extraction of hemicellulose polymers with high molecular weights. To optimize MAE, different treatment powers (125–573 W) of presoaked spruce sawdust in water and 1 M sodium hydroxide solution for a period of 60 min were tested. The yield of hemicellulose extraction increased with the microwave power in both mediums, but with a clear advantage for presoaked samples in basic medium. The characterization of extracted hemicelluloses has shown high extraction selectivity depending on the medium of impregnation of sawdust before MAE: High-molecular-mass acetylated galactoglucomannans (M_w ∼ 41 kDa) were isolated after presoaking in water and higher molecular mass arabinoglucoronoxylans (M_w ∼ 66 kDa) in basic medium.     

Tuning of graphitic carbon nitride (g-C3N4) for photocatalysis: A critical review

Graphitic carbon nitride (g-C₃N₄) is a remarkable semiconductor catalyst that has attracted widespread attention as a visible light photo-responsive, metal-free, low-cost photocatalytic material. Pristine g-C₃N₄ suffers fast recombination of photogenerated electron-hole pairs, low surface area, and insufficient visible light absorption, resulting in low photocatalytic efficiency. This review presents the recent progress, perspectives, and persistent challenges in the development of g-C₃N₄-based photocatalytic materials. Several approaches employed to improve the visible light absorption of the materials including metal and non-metal doping, co-doping, and heterojunction engineering have been extensively discussed. These approaches, in general, were found to decrease the material’s bandgap, increase the surface area, reduce charge carrier recombination, and promote visible light absorption, thereby enhancing the overall photocatalytic performance. The material has been widely used for different applications such as photocatalytic hydrogen production, water splitting, CO₂ conversion, and water purification. The work has also identified various limitations and weaknesses associated with the material that hinders its maximum utilization under visible illumination and presented state-of-the-art solutions that have been reported recently. The summary presented in this review would add an invaluable contribution to photocatalysis research and facilitate the development of efficient visible light-responsive semiconducting materials.