Investigation of the CeFe binary system

The CeFe binary system was investigated and an FeCe binary phase diagram was proposed. This system consists of

• 1.(i) two peritectic reactions, γ-Fe + L → Ce₂Fe₁₇ and Ce₂Fe₁₇ + L → CeFe₂, occurring isothermally at 1063°C and 925°C respectively;
• 2.(ii) a eutectic reaction, L → CeFe₂ + Ce, occurring isothermally at 592°C with eutectic containing 83.3 at.% Ce (92.6 wt.% Ce);
• 3.(iii) a peritectoid reaction, γ-Fe + Ce₂Fe₁₇ → α-Fe(Ce), occurring isothermally at 922 °C.

The solid solubility of cerium in iron in the temperature range 850–900 °C was found to be less than 0.04 at.% (0.1 wt.%). The Curie temperature of α-Fe(Ce) was slightly lowered with increasing cerium content in solid solution.     

Comparison of the magnetic properties of MmFeband NdFeB compounds

NdFeB and corresponding MmFeB compounds were studied, the high field magnetization at 4.2 K, the a.c. susceptibility (4.2 < T < 300 K) and the anisotropy field were measured using the singular point detection technique (77 < T < 570 K). At room temperature the anisotropy field of the MmFeB is about 3T, whereas that of NdFeB compounds is about 7T. The MmFeB compounds showed effects due to the cerium (lowering the Curie temperature) as well as due to the neodymium (spin reorientation at low temperatures).     

Mössbauer Study of the Structure of Fe - Zircon System

Iron-doped silicate (zircon), prepared by a ceramic method with the addition of LiF as mineralizer, was analyzed by X-ray powder diffraction (XRD) and ⁵⁷Fe Mössbauer spectroscopy to obtain information on the solid solution formation. The results of X-ray diffraction and Mössbauer spectroscopy have shown that only a small fraction of iron, about 1.5 mol%, is incorporated in the zircon structure as paramagnetic Fe³⁺ species while the remaining Fe³⁺ cations form magnetic -Fe₂O₃ particles which are trapped within the zircon matrix.     

Mössbauer studies of the iron-sulfur cluster-free hydrogenase: the electronic state of the mononuclear Fe active site

The iron-sulfur cluster-free hydrogenase (Hmd) from methanogenic archaea harbors an iron-containing, light-sensitive cofactor of still unknown structure as prosthetic group. The enzyme is reversibly inhibited by CO and cyanide and is EPR silent. We report here on M?ssbauer spectra of the (57)Fe-labeled enzyme and of the isolated cofactor. The spectrum of the holoenzyme measured at 80 K revealed a doublet peak with an isomer shift delta = 0.06 mm.s(-)(1) and a quadrupole splitting of DeltaE(Q) = 0.65 mm.s(-)(1) (at pH 8.0). The signal intensity corresponded to the enzyme concentration assuming 1 Fe per mol active site. Upon addition of CO or cyanide to the enzyme, the isomer shift decreased to -0.03 mm.s(-)(1) and -0.00(1) mm.s(-)(1), and the quadrupole splitting increased to 1.38 mm.s(-)(1) and 1.75 mm.s(-)(1), respectively. The three spectra could be perfectly simulated assuming the presence of only one type of iron in Hmd. The low isomer shift is characteristic for Fe in a low oxidation state (0, +1, +2). When the spectra of the holoenzyme and of the CO- or cyanide-inhibited enzyme were measured at 4 K in a magnetic field of 4 and 7 T, the spectra obtained could be simulated assuming the presence of only the external magnetic field, which excludes that the iron in the active site of Hmd is Fe(I), high-spin Fe(0), or high-spin Fe(II). M?ssbauer spectra of the isolated Hmd cofactor are also reported.     

Influence of Changing the Remote Substituents on Charge Transfer Properties of Cyanide-Bridged Trinuclear Fe−Ru−Fe Complexes

To investigate the effect of ligand remote (>10 Å) substituents on the bridging metal center on the metal-to-metal charge transfer (MMCT) properties in cyanidometa-bridged complexes, a series of new cyanidometal-bridged complexes and their one-electron and two-electron oxidation products have been synthesized and well characterized (namely, trans-[Cp(dppe)Fe−NC−(L)Ru(PPh₃)−CN−Fe(dppe)Cp][PF₆]_n (n=2, 3, 4) (L=dmptpy, 1[PF₆]_n ; L=meoptpy, 2[PF₆]_n ; L=t-Buptpy, 3[PF₆]_n ) (Cp=1,3-cyclopentadiene, dppe=1,2-bis(diphenylphosphino)ethane, PPh₃=triphenylphosphine, dmptpy=4′-(4-dimethylaminophenyl)-2,2′,6′,2′′-terpyridine, meoptpy=4′-(4-methoxyphenyl)-2,2′,6′,2′′-terpyridine, t-Buptpy=4′-(4-tertbutylphenyl)-2,2′,6′,2′′-terpyridine)). The investigations suggest that the cyanido-stretching (ν_CN) vibration energy for the complexes is unsensitive to the electron-donating ability change of the remote substituents of the cyanidometal bridging auxiliary ligand from tertbutyl, methoxy to dimethylamino group. However, the MMCT energies of the one- and two-electron oxidation complexes are still sensitive to the remote substituents of the ligand on the bridging metal center, and decreases with the increase of the electron-donating ability of the remote substituents from tertbutyl, methoxy to dimethylamino group. All one-electron and two-electron oxidation products belong to Class II mixed valence compounds according to the classification of Robin and Day.     

Synthesis of Fe–Ni invar alloy nanopowder by the electrical explosion of wire in the liquid

Research on Chemical Intermediates - The present work studied the synthesis of Fe–Ni Invar alloy nanopowder by the electrical explosion of wire (EEW) in deionized water. X-ray diffraction...     

Promotion of the oxygen evolution performance of Ni–Fe layered hydroxides via the introduction of a proton-transfer mediator anion

Developing efficient catalysts with high durability and activity for the oxygen evolution reaction(OER)is imperative for sustainable energy conversion technologies,including hydrogen generation and CO₂ reduction,as well as other electrochemical energy storage systems.To this end,a comprehensive understanding of the mechanism for the water oxidation reaction is vital.Herein,a surfactant,nonafluoro-1-butanesulfonate(FBS),was introduced into Ni-Fe layered double hydroxide(Ni Fe-FBS/CFP)via electrochemical deposition on the surface of a carbon fiber paper(CFP)substrate.The as-prepared Ni Fe-FBS/CFP electrode exhibited excellent catalytic activities for OER compared to the Ni-Fe layered double hydroxide based electrode(Ni Fe-LDH/CFP),an excellent stability of 15 h,and an ultralow Tafel slope of 25.8 m V dec-1.Furthermore,by combining the results of p H-dependent kinetics investigations,chemical probing,proton inventory studies,and isotopic and atom-protontransfer measurements,it was observed that a proton-transfer process controls the reaction rates of both the Ni Fe-LDH and Ni Fe-FBS catalysts,and the residual sulfonate groups serve as proton transfer mediator to accelerate the proton transfer rate.     

The absolute value of the rate constant of the liquid-phase reaction SO 5 −. + Fe(II)

An analytical method for monitoring the Fe²⁺ concentration during liquid-phase sulfite oxidation catalyzed by iron ions is described. The concentration conditions under which the Fe(III)/Fe(II) ratio is uniquely related to the rate constant of the reaction SO ₅ ^?. + Fe²⁺ are found by computer analysis. The experimental and calculated Fe(III)/Fe(II) ratio data are in agreement at $k_{(SO_5^{ - \cdot } + Fe^{2 + } )} = 3.2 \times 10^6 1mol^{ - 1} s^{ - 1} $ . This is one of the three rate constant values known from the literature, which differ by a factor greater than 70.     

Analysis of the Glass-Forming Ability of Fe–Er Alloys,Based on Thermodynamic Modeling

The Fe–Er phase diagram and thermodynamic properties of all its phases are assessed by means of self-consistent analysis. To refine the data on phase equilibria in the Fe–Er system, an investigation is performed in the 10–40 at % range of Er concentrations. The temperature–concentration dependences of the thermodynamic properties of a melt are presented using the model of ideal associated solutions. Thermodynamic parameters of each phase are obtained, and the calculated results are in agreement with available experimental data. The correlation between the thermodynamic properties of liquid Fe–Er alloys and their tendency toward amorphization are studied. It is shown that compositions of amorphous alloys prepared by melt quenching coincide with the ranges of concentration with the predominance of Fe₃Er and FeEr₂ associative groups that have large negative entropies of formation.     

Effect of sulphur addition on the properties of FeTi alloy for hydrogen storage

Addition of sulphur to the Fe-Ti alloy was found to produce a marked improvement in the properties of the alloy for hydrogen storage. The most effective composition was FeTi_1.05S_0.02, which had a low activation temperature (80–100 °C), a short incubation time (10–30 h) and a good equilibrium plateau pressure over a wide concentration range of absorbed hydrogen. The degree of pulverization for this alloy after the absorption-desorption cycle test was comparatively moderate. The sulphur added to the alloy was converted into Ti₂S which was precipitated in a network structure with strips about 5 μm wide separated by spaces of dimensions about 20–50 μm.     

Determination of the stability and magnetic properties of Fe–Pd nitride using the generalised gradient approximation (GGA)

In this study, an electronic structure calculation of the substituted nitride PdFe₃N was conducted, and a posterior understanding of its structural and magnetic properties was obtained. A first principle method was applied to study the lattice parameter variation in relation to the energy of solid formation. After the equilibrium parameter was found, some properties of the ground state, such as the magnetic moment and the bulk modulus, were calculated. Preliminary observations show that the material properties of γ′-Fe₄N vary significantly with the insertion of the palladium atom in the matrix as well as when the material is subjected to applied pressure. The density of states shows a strong interaction between the s states of nitrogen and, primarily, the s and p states of iron, presenting a weak interaction with the palladium atoms. The analysis of such properties illustrates why these nitrides have a promising future for use in technological applications.     

Experimental investigation of the effect of an external magnetic field on the thermal conductivity and viscosity of Fe3O4–glycerol

Journal of Thermal Analysis and Calorimetry - Thermophysical properties, such as thermal conductivity and viscosity, of magnetic nanofluids (MNFs) can be enhanced by applying external magnetic...     

Modeling the Signatures of Hydrides in Metalloenzymes: ENDOR Analysis of a Di-iron Fe(μ-NH)(μ-H)Fe Core

The application of 35 GHz pulsed EPR and ENDOR spectroscopies has established that the biomimetic model complex L(3)Fe(μ-NH)(μ-H)FeL(3) (L(3) = [PhB(CH(2)PPh(2))(3)](-)) complex, 3, is a novel S = (1)/(2) type-III mixed-valence di-iron II/III species, in which the unpaired electron is shared equally between the two iron centers. (1,2)H and (14,15)N ENDOR measurements of the bridging imide are consistent with an allyl radical molecular orbital model for the two bridging ligands. Both the (μ-H) and the proton of the (μ-NH) of the crystallographically characterized 3 show the proposed signature of a 'bridging' hydride that is essentially equidistant between two 'anchor' metal ions: a rhombic dipolar interaction tensor, T ≈ [T, -T, 0]. The point-dipole model for describing the anisotropic interaction of a bridging H as the sum of the point-dipole couplings to the 'anchor' metal ions reproduces this signature with high accuracy, as well as the axial tensor of a terminal hydride, T ≈ [-T, -T, 2T], thus validating both the model and the signatures. This validation in turn lends strong support to the assignment, based on such a point-dipole analysis, that the molybdenum-iron cofactor of nitrogenase contains two [Fe-H(-)-Fe] bridging-hydride fragments in the catalytic intermediate that has accumulated four reducing equivalents (E(4)). Analysis further reveals a complementary similarity between the isotropic hyperfine couplings for the bridging hydrides in 3 and E(4). This study provides a foundation for spectroscopic study of hydrides in a variety of reducing metalloenzymes in addition to nitrogenase.     

Gamma irradiation effects on the kinetics of the solid-state reaction in the system MgO·Fe2O3

The kinetics of magnesium ferrite spinel formation reaction was studied in powdered mixtures of MgO and Fe₂O₃ with different mole ratios. The formation reaction was followed by a titrimetric method and the results were discussed in terms of Jander's diffusion equation. The effects of gamma irradiation of the mixed powdered oxides on the reaction rate constants and the activation energies were determined and discussed.     

Effect of hydrogen reduction temperature on the microstructure and magnetic properties of Fe–Ni powders

The effect of hydrogen reduction temperature on the properties of Fe–Ni powders was described. The mixed powders of Fe-oxide and NiO were prepared by chemical solution mixing of nitrates powders and calcination at 350 °C for 2 h in air. The calcined powders formed small agglomeration with an average particle size of 100 nm. The microstructure and magnetic properties were investigated by using X-ray diffractometry, thermogravimetry, differential thermal analyzer, and vibrating sample magnetometer. Microstructure and thermal analysis revealed that the Fe-oxide and NiO phase were changed to FeNi₃ phase in the temperature range of 245–310 °C, and by heat-up to 690 °C the FeNi₃ phase was transformed to γ-FeNi phase. The reduced powder at 350 °C showed saturation magnetization of 76.3 emu/g and coercivity of 205.5 Oe, while the reduced powders at 690 °C exhibited saturation magnetization of 84.0 emu/g and coercivity of 14.0 Oe. The change of magnetic properties was discussed by the observed microstructural features.

     

Fe/SiO_2 as an XAFS-Probe for the Study on the Effect of Sodium Promotion to the Silica Surface

Ｆｅ／ＳｉＯ２ａｓａｎＸＡＦＳ－ＰｒｏｂｅｆｏｒｔｈｅＳｔｕｄｙｏｎｔｈｅＥｆｅｃｔｏｆＳｏｄｉｕｍＰｒｏｍｏｔｉｏｎｔｏｔｈｅＳｉｌｉｃａＳｕｒｆａｃｅＮＩＵＪｉａｎｚｈｏｎｇＫＯＵＹｕａｎＬＩＳｈｕｂｅｎＷＵＪｉｎｇａｎｇ（ＳｔａｔｅＫｅｙＬａｂ...     

Influence of Mn on the solidification of Fe–Si–Al alloy for non-oriented electrical steel

Differential scanning calorimetry, thermodynamic calculations, and metallographic analyses were used for a determination of the solidification sequence in a Fe–2.42 %Si–0.5 %Al–0.94 %Mn alloy. For the prediction of the solidification process of the Fe–Si–Al–Mn alloy also a modified Scheil–Gulliver solidification model was used. According to the thermodynamic calculations the two-phase region in the selected Fe–Si–Al–Mn alloy is stable between 1,303 and 913 °C. The highest mass-fraction of the γ-phase is reached at 1,150 °C. With decreasing temperature the austenite retransforms into ferrite. In the temperature range where the thermodynamic calculations predict the existence of the two-phase region in the DSC curves, weak thermal events were observed. A post-exposure metallographic analysis revealed that the substructures in the ferrite microstructure indicate the γ → α phase transformation. This suggests consistency between the differential scanning calorimetry, the thermodynamic calculations, and the metallographic analyses.     

Fe doped aluminoborate PKU-1 catalysts for the ketalization of glycerol to solketal: Unveiling the effects of iron composition and boron

An inexpensive Fe doped aluminoborate consisted of 18% Fe in PKU-1 material that exhibits high selectivity of 4-hydroxymethy-2,2-dimethyl-1,3-dioxolane(Solketal, 98.3%), considerable activity(TOF 51.7 h-1),and recyclable ability in the ketalization of glycerol to Solketal with acetone at 318 K has been developed.Our study demonstrated that the structure of Fe(less agglomerated iron species vs. Fe Oxclusters) can be tuned by changing Fe loading in the PKU-1 material, which correlated well with ex...