An experimental and theoretical investigation on adsorption properties of some diphenolic Schiff bases as corrosion inhibitors at acidic solution/mild steel interface

The effect of novel synthesized three Schiff bases, namely, 1,3-bis[2-(2-hydroxy benzylidenamino) phenoxy] propane (P1), 1,3-bis[2-(5-chloro-2-hydroxybenzylidenamino) phenoxy] propane (P2), and 1,3-bis[2-(5-bromo-2-hydroxybenzylidenamino) phenoxy] propane (P3), on the corrosion of mild steel in 0.1 M HCl was investigated using potentiodynamic polarization and electrochemical impedance spectroscopy methods. Polarization measurements suggest that P1 acts as mixed type inhibitor while P2 and P3 behave as mainly cathodic inhibitors for acidic corrosion of steel. All electrochemical measurements show that inhibition efficiencies increase with increase in inhibitor concentration. This reveals that inhibitive actions of inhibitors were mainly due to adsorption on steel surface. Adsorption of these inhibitors follows Temkin adsorption isotherm. The correlation between the adsorption ability of inhibitors and their molecular structures has been investigated using quantum chemical parameters obtained by MNDO semi-empirical method. Calculated quantum chemical parameters indicate that Schiff bases adsorbed on steel surface by chemical mechanism.     

Adsorption and inhibitive properties of aminobiphenyl and its Schiff base on mild steel corrosion in 0.5 M HCl medium

Electrochemical measurements were performed to investigate the effectiveness and adsorption behaviour of aminobiphenyl (Aph) and 2-(3-hydroxybenzylideneamino)biphenyl (Aph-S), as corrosion inhibitors for mild steel (MS) in 0.5 M HCl solution. Potentiodynamic polarization, linear polarization resistance (LP) and electrochemical impedance spectroscopy (EIS) techniques were applied to study the metal corrosion behaviour in the absence and presence of different concentrations of Aph and Aph-S. In order to gain more information about adsorption mechanism the AC impedance technique was used to evaluate the potential of zero charge (PZC) from polarization resistance (R_p) versus voltage (E) plot. Potentiodynamic polarization measurements showed that Aph act as cathodic type inhibitor where as Aph-S act mixed type. The inhibition efficiency (IE%) increases with increasing concentration of compounds and reached 92.6% for Aph and 97.2% for Aph-S at 5 × 10⁻³ M. Double layer capacitance (C_dl) and polarization resistance (R_p) values are derived from Nyquist plots obtained from AC impedance studies. The experimental data fit Langmuir isotherm for both Aph and Aph-S, and from the adsorption isotherm some thermodynamic data for the adsorption processes are calculated and discussed. The effect of exposure time on the corrosion behaviour of mild steel in the absence and presence of inhibitor over 168 h was also studied.     

Experimental,Monte Carlo and molecular dynamics simulations to investigate corrosion inhibition of mild steel in hydrochloric acid solutions

The efficiency of three furan derivatives, namely 2-(p-toluidinylmethyl)-5-methyl furan (Inh. A), 2-(p-toluidinylmethyl)-5-nitro furan (Inh. B) and 2-(p-toluidinylmethyl)-5-bromo furan (Inh. C), as possible corrosion inhibitors for mild steel in 1.0 M HCl, has been determined by weight loss and electrochemical measurements. These compounds inhibit corrosion even at very low concentrations, and 2-(p-toluidinylmethyl)-5-methyl furan (Inh. A) is the best inhibitor. Polarization curves indicate that all compounds are mixed-type inhibitors, affecting both cathodic and anodic corrosion currents. Adsorption of furan derivatives on the mild steel surface follows the Langmuir adsorption isotherm, and the calculated Gibbs free energy values confirm the chemical nature of the adsorption. Monte Carlo simulations technique incorporating molecular mechanics and molecular dynamics can be used to simulate the adsorption of furan derivatives on mild steel surface in 1.0 M HCl.     

Synthesis,characterization and corrosion inhibition efficiency of 2-(6-methylpyridin-2-yl)-1H-imidazo[4,5-f][1,10] phenanthroline on mild steel in sulphuric acid

Phenanthroline derivative, 2-(6-methylpyridin-2-yl)-1H-imidazo[4,5-f][1,10] phenanthroline (MIP) was synthesized and characterized by elemental analysis, FT-IR, ¹H NMR, ¹³C NMR, and single crystal X-ray diffraction study. MIP was evaluated as corrosion inhibitor for mild steel in 0.5 M H₂SO₄ solution using gravimetric and UV–Visible spectrophotometric methods at 303–333 K. Results obtained show that MIP acts as inhibitor for mild steel in H₂SO₄ solution. The inhibition efficiency was found to increase with increase in MIP concentration but decreased with temperature. Activation parameters and Gibbs free energy for the adsorption process using statistical physics were calculated and discussed. The UV–Visible absorption spectra of the solution containing the inhibitor after the immersion of mild steel specimen indicate the formation of a MIP-Fe complex.     

Experimental,DFT studies and molecular dynamic simulation on the corrosion inhibition of carbon steel in 1 M HCl by two newly synthesized 8-hydroxyquinoline derivatives

In the present work, two new 8-hydroxyquinoline derivatives namely, 5-(((2-hydroxybenzylidene)amino)methyl) 8-hydroxyquinoline [HBMQ] and 5-(((4-chlorobenzylidene)amino)methyl) 8-hydroxyquinoline [CBMQ] were synthesized and investigated as corrosion inhibitors against the dissolution of carbon steel (C38 steel) in 1 M HCl. These compounds were obtained with high yield, and their structures were characterized by nuclear magnetic resonance spectroscopy (NMR) and elemental analysis. Gravimetric, electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and surface morphology analyses utilizing scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) were used to quantify inhibitory performance. The adsorption process of inhibitory compounds was then demonstrated using quantum mechanics approaches such as Density Functional Theory (DFT) and Molecular Dynamic Simulation (MD). Based on EIS results, the investigated derivatives effectively inhibit the degradation of C38 steel over the entire concentration range with a maximum efficiency of 91.9% and 88.0% for [CBMQ] and [HBMQ], respectively, at 10^?3 M. In addition, the PDP studies revealed that [HBMQ] and [CBMQ] compounds acted according to a mixed-type mechanism. Moreover, the adsorption mechanism follows the Langmuir isotherm model. The quantum theoretical study by DFT and MD simulation confirmed the experimental results.     

Corrosion inhibition performance of 2-ethyl phenyl-2, 5-dithiohydrazodicarbonamide on Fe (110)/Cu (111) in acidic/alkaline solutions: Synthesis,experimental, theoretical,and molecular dynamic studies

Herein, 2-ethyl phenyl-2,5-dithiohydrazodicarbonamide (2EPDCA) was synthesised and tested as a corrosion inhibitor for mild steel (MS) and copper (Cu) in 1 M HCl and 3.5% NaCl, respectively. Fourier transform infrared spectroscopy (FT-IR) and (NMR) nuclear magnetic resonance (¹H, ¹³C) were used to identify the chemical structure. Both experimental and computational approaches have been conducted to evaluate inhibitor efficiency on both metal systems. The electrochemical results showed that the 2EPDCA inhibition efficiency for MS systems was 95% at 1 × 10^?2 M, while in copper systems it was 97.5% at 1 × 10^?2 M. The Langmuir adsorption isotherm was fitted using adsorption surface coverage data, and for inhibitor in both systems, the kind of adsorption was mixed (physisorption and chemisorption). Through scanning electron microscopy (SEM), EDX, and atomic force microscopy (AFM) tests, we have confirmed the presence of the inhibitor molecules on the metal surface in both systems. Quantum chemistry simulations indicate that the superior corrosion inhibition efficacy of 2EPDCA on copper compared to mild steel surfaces is attributable to the former's greater electron donating propensity on copper. The adsorption of 2EPDCA molecules on Fe (110) and Cu (111) surfaces was further verified by molecular dynamic simulations, with the former having a greater adsorption energy. The results indicate that the corrosion inhibitor was effective even in harsh conditions, and it can be thought of as a novel corrosion inhibitor for mild steel and copper that provides good protection.     

Synthesis,characterization, density functional theory studies and antibacterial activity of a new Schiff base dioxomolybdenum(VI) complex with tryptophan as epoxidation catalyst

A cis ‐dioxomolybdenum(VI) complex was prepared with MoO₂(acac)₂ and a Schiff base ligand (2‐((2‐hydroxybenzylidene)amino)‐3‐(1H ‐indol‐3‐yl)propanoic acid) derived from salicylaldehyde and l ‐tryptophan in ethanol and designated as [MoO₂(Sal‐Tryp)(EtOH)]. It was characterized using several techniques including thermogravimetric and elemental analyses and mass, Fourier transform infrared and UV–visible spectroscopies. Theoretical calculations were performed using density functional theory for studying the molecular structure. An in vitro antibacterial activity evaluation showed that [MoO₂(Sal‐Tryp)EtOH] complex exhibits good inhibitory effects against Gram‐positive (Bacillus subtilis , Staphylococcus aureus ) and Gram‐negative (Escherichia coli , Pseudomonas aeruginosa ) bacteria in comparison to standard antibacterial drugs. It was also found that [MoO₂(Sal‐Tryp)EtOH] complex successfully catalyses the epoxidation of cyclooctene, norbornene, cyclohexene, styrene, α‐methylstyrene and trans ‐stilbene, with 45–100% conversions and 64–100% selectivities. Based on the obtained results, the heterogeneity and reusability of the catalyst seem promising.     

Antioxidant potential of styrene pyrone polyphenols from Inonotus obliquus: A combined experimental,density functional theory (DFT) approach and molecular dynamic (MD) simulation

Polyphenols containing styrene pyranone skeleton are unique to porous fungi. Inonotus obliquus (IO) is a medicinal and edible porous fungus. Twelve phenolic compounds containing four styryl pyranone polyphenols from IO were isolated and identified in this work. The antioxidant ability of the isolates was characterized utilizing the ferric reducing antioxidant power (FRAP) assay and 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonate) (ABTS) radical scavenging test. Styrylpyranone polyphenols, especially methylinoscavin B, could capture free radicals better than other phenolic compounds, and quantum chemical calculations also confirmed this evaluation. The density functional theory (DFT) calculation data showed that Styrylpyranone polyphenols, especially methylinoscavin B, have a lower energy gap, higher softness and higher electronic chemical potential than other phenolic compounds. The bond dissociation energy values of the bond in C7ʹ O–H of the methylinoscavin B molecule are less than those in C11 and C6ʹ O–H when reacting with ∙OOH (selected as a representative free radical). On the basis of calculations, hydrogen atom transfer (HAT) is supposed to be a preferred mechanism over single electron transfer (SET) when phenolic compounds react with free radicals. Moreover, after treatment with final concentrations of 0.5, 1, 2, 3, 4 and 5 μM phelligridin E (PHE), the activity of SOD1 increased by 70.15%, 11.36%, 145.45%, 172.73%, 205.05% and 275.23%, respectively. The molecular dynamics simulation (MD) study of PHE employed SOD1 (PDB ID: 6FN8). The MD results showed that the hydrogen bonds between ASP147 of SOD1 and PHE promote GLU223-ARG224 to form a stable C coil after combining with PHE. The formation of the C Coil enhanced the stability of the electrostatic loop (EL) of SOD1 and the rate of diffusion of the superoxide anion to the active site. Styrylpyrone polyphenols of Inonotus obliquus origin have the potential to be a source of vigorous free radical scavengers and antioxidant enzyme activators.     

Physicochemical characterization of nanobidentate ferrocene‐based Schiff base ligand and its coordination complexes: Antimicrobial,anticancer, density functional theory,and molecular operating environment studies

A novel bidentate Schiff base ligand (HL, Nanobidentate Ferrocene based Schiff base ligand L (has one replaceable proton H)) was prepared via the condensation of 2‐amino phenol with 2‐acetyl ferrocene. The ligand was characterized using elemental analysis, mass spectrometry, infrared (IR) spectroscopy, ¹proton nuclear magnetic resonance (H‐NMR) spectroscopy, scanning electron microscopy (SEM), and thermal analysis. The corresponding 1:1 metal complexes with some transition‐metal ions were additionally characterized by their elemental analysis, molar conductance, SEM, and thermogravimetric ana1ysis (TGA). The complexes had the general formula [M(L)(Cl)(H₂O)₃]xCl·nH₂O (M = Cr(III), Mn(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), and Cd(II)), (x = 0 for Mn(II), Co(II), Ni(II), Cu(II), Zn(II), and Cd(II), x = 1 for Cr(III) and Fe(III)), (n = 1 for Cr(III), n = 3 for Mn(II) and Co(II), n = 4 for Fe(III), Ni(II), Cu(II), Zn(II), and Cd(II)). Density functional theory calculations on the HL ligand were also carried out in order to clarify molecular structures by the B31YP exchange‐correlation function. The results were subjected to molecular orbital diagram, highest occupied mo1ecu1ar orbital–lowest occupied molecular orbital, and molecular electrostatic potential calculations. The parent Schiff base and its eight metal complexes were assayed against four bacterial species (two Gram‐negative and two‐Gram positive) and four different antifungal species. The HL ligand was docked using molecular operating environment 2008 with crystal structures of oxidoreductase (1CX2), protein phosphatase of the fungus Candida albicans (5JPE), Gram(?) bacteria Escherichia coli (3T88), Gram(+) bacteria Staphylococcus aureus (3Q8U), and an androgen‐independent receptor of prostate cancer (1GS4). In order to assess cytotoxic nature of the prepared HL ligand and its complexes, the compounds were screened against the Michigan cancer foundation (MCF)‐7 breast cancer cell line, and the IC₅₀ values of compounds were calculated.     

Ligational,density functional theory,and biological studies on some new Schiff base 2-(2-hydroxyphenylimine)benzoic acid (L) metal complexes

The metal ions Co(II), Ni(II), Zn(II), Zr(IV), and Hg(II) reacted with synthesized Schiff base (L) in mole ratios 1:2 (M:L) formed metal complexes. The structure of the prepared compounds was identified based on the data obtained from elemental analyses, magnetic measurement, melting point, conductivity, Fourier-transform infrared, UV–Vis., nuclear magnetic resonance spectroscopy, X-ray diffraction (XRD) spectra, and thermal analysis (TG/DTG [thermogravimetric/differential thermal analysis]). The results indicate that the L bound as bidentate through the oxygen atom of the hydroxyl group and nitrogen atom of the azomethine group with the metal ions and the complexes is electrolyte in nature. TG/DTG studies confirmed the chemical formula for complexes. The kinetic and thermodynamic parameters such as E^*, ΔH^*, ΔS^*, and ΔG^* were determined by using Coats–Redfern and Horowitz–Metzger methods at n = 1 and n ≠ 1. The XRD patterns exhibited a semicrystalline nature lying between the amorphous and crystalline nature for L, (D), and (E), but the complexes (A), (B), and (C) possessed a crystalline character. Density functional theory confirmed the structural geometry of the complexes. In vitro antimicrobial activities were performed for L and its metal complexes.     

Syntheses,EPR spectral studies and crystal structures of manganese(II) complexes of neutral N,N donor bidentate Schiff bases and azide/thiocyanate as coligand

Four manganese(II) complexes Mn₂(paa)₂(N₃)₄ (1), [Mn(paa)₂(NCS)₂]·³/₂H₂O (2), Mn(papea)₂(NCS)₂ (3), [Mn(dpka)₂(NCS)₂]·¹/₂H₂O (4) of three neutral N,N donor bidentate Schiff bases were synthesized and physico-chemically characterized by means of partial elemental analyses, electronic, infrared and EPR spectral studies. Compounds 3 and 4 were obtained as single crystals suitable for X-ray diffraction. Compound 4 recrystallized as Mn(dpka)₂(NCS)₂. Both the compounds crystallized in the monoclinic space groups P2₁ for 3 and C2/c for 4. Manganese(II) is found to be in a distorted octahedral geometry in both the monomeric complexes with thiocyanate anion as a terminal ligand coordinating through the nitrogen atom. EPR spectra in DMF solutions at 77 K show hyperfine sextets with low intensity forbidden lines lying between each of the two main hyperfine lines and the zero field splitting parameters (D and E) were calculated.     

Investigation on corrosion inhibition effect of N-[4-(1,3-benzo[d]thiazol-2-ylcarbamoyl)phenyl]quinoline-6-carboxamide as a novel organic inhibitor on mild steel in 1N HCl at different temperatures: Experimental and theoretical study

A new novel organic corrosion inhibitor N-[4-(1,3-benzo[d]thiazol-2-ylcarbamoyl)phenyl]quinoline-6-carboxamide (NBCPQC) has been synthesized. The synthesized novel organic inhibitor NBCPQC used to be carried out on mild steel corrosion in 1N HCl for the first time. The studied inhibitor was once evaluated as corrosion inhibitor for mild steel in 1N of HCl solution using electrochemical research which advocated that a protective film is form by the process of inhibitor absorption on the surface of mild steel. Inhibitor shows a better inhibiton efficiency of maximum above 90% in 1N HCl medium. Inhibitors show a better efficiency by way of reducing and sluggish down the corrosion process however on growing the temperature it is weakened on controlling corrosion. In addition to this adsorption isothermal models had been interpreted to fit the adsorption behaviour of the inhibitor compound on mild steel surface. Thus the result reveals that the compound shows a Langmuir adsorption isotherm.     

Synthesis,characterization, density functional theory calculations,and in vitro antibacterial activity of novel transition metal complexes containing an O3-tridentate amoxicillin-based Schiff base: A silver(II) complex as alternative against Pseudomonas aeruginosa resistant to amoxicillin

Transition metal complexes containing an amoxicillin-based Schiff base (H₂L, 3 ) obtained from the condensation of amoxicillin 1 with salicylaldehyde 2 were prepared. Spectroscopic and physicochemical techniques, namely, UV–visible, Fourier-transform infrared spectroscopy, ¹H NMR, electron paramagnetic resonance, transmission electron microscopy, mass spectrometry, magnetic susceptibility, molar conductance, density functional theory (DFT) calculations, together with elemental and thermal analyses were used to characterize the synthesized complexes. Based on these studies, the general formulae [ML(H₂O)₃], where M = Mn 4 , Ni 5 , Zn 6 , and [ML(H₂O)], where M = Cu 7 , Ag 8 , were proposed for the complexes. The amoxicillin-based Schiff base ligand behaved as a dianionic O₃-tridentate chelating agent. DFT studies and magnetic and spectral data revealed octahedral geometries for Mn, Ni, and Zn atoms and distorted tetrahedral geometries for Cu(II) and Ag(II) complexes. Synthesized compounds were tested for antibacterial activity by both agar disk diffusion method and the minimum inhibitory concentration. in vitro bacterial viability revealed that complex 5 had similar antibacterial activity as 1 against Staphylococcus aureus and Staphylococcus epidermidis, whereas Pseudomonas aeruginosa, resistant to amoxicillin, was sensitive to complex 8 . The antibacterial activity of complex 8 could be attributed to its greater catalytic activity as shown by DFT calculations. Toxicity bioassay of the tested compounds showed LC₅₀ values > 1000 ppm, indicating their nontoxicity against brine shrimp nauplii (Artemia salina).     

Co(II), Ni(II), Cu(II) and Zn(II) complexes of aminothiazole‐derived Schiff base ligands: Synthesis,characterization, antibacterial and cytotoxicity evaluation,bovine serum albumin binding and density functional theory studies

Transition metal complexes of type M(L)₂(H₂O)_x were synthesized, where L is deprotonated Schiff base 2,4‐dihalo‐6‐(substituted thiazol‐2‐ylimino)methylphenol derived from the condensation of aminothiazole or its derivatives with 2‐hydroxy‐3‐halobenzaldehyde and M = Co²⁺, Ni²⁺, Cu²⁺ and Zn²⁺ (x = 0 for Cu²⁺ and Zn²⁺; x = 2 for Co²⁺ and Ni²⁺). The synthesized Schiff bases and their metal complexes were thoroughly characterized using infrared, ¹H NMR, electronic and electron paramagnetic resonance spectroscopies, elemental analysis, molar conductance and magnetic susceptibility measurements, thermogravimetric analysis and scanning electron microscopy. The results reveal that the bidentate ligands form complexes having octahedral geometry around Co²⁺ and Ni²⁺ metal ions while the geometry around Cu²⁺ and Zn²⁺ metal ions is four‐coordinated. The geometries of newly synthesized Schiff bases and their metal complexes were fully optimized in Gaussian 09 using 6–31 + g(d,p) basis set. Fluorescence quenching data reveal that Zn(II) and Cu(II) complexes bind more strongly to bovine serum albumin in comparison to Co(II) and Ni(II) complexes. The ligands and their complexes were evaluated for in vitro antibacterial activity against Escherichia coli ATCC 25922 (Gram negative) and Staphylococcus aureus ATCC 29213 (Gram positive) and cytotoxicity against lever hepatocellular cell line HepG2.