CuS–MWCNT based electrochemical sensor for sensitive detection of bisphenol A

The rapid and simple detection of bisphenol A is very important for the safety and reproduction of organisms. Here, a sensitive and reliable electrochemical sensor was established for bisphenol A detection based on the high amplification effect of copper sulfide-multi-walled carbon nanotube (CuS–MWCNT) nanocomposites. The flower-like CuS–MWCNT were successfully synthesized by a simple hydrothermal method accompanied by polyvinylpyrrolidone (PVP). Compared with bare glassy carbon electrode (GCE), CuS–MWCNT modified GCE could amplify the electrochemical signals in about ten times, which was attributed to the synergistic effect of CuS and MWCNT. The MWCNT could increase the specific surface area of electrodes and improve the electrode activity. The integration of CuS could further enhance the electrode conductivity as well as accelerate the electron transfer rate. Raman spectra and transmission electron microscope (TEM) were used to characterize the successful fabrication of CuS–MWCNT nanocomposites and its uniform and monodispersed morphology. Under optimizing conditions, the oxidation currents of bisphenol A via the differential pulse voltammetric (DPV) showed a good linear relationship with its concentration in a wide range of 0.5–100 μM, with a detection limit of 50 nM. This electrochemical sensor of bisphenol A provided a convenient and economical platform with high sensitivity and reproducibility, which had great potential in environmental monitoring.     

Microwave-assisted synthesis of organic–inorganic poly(3,4-ethylenedioxythiophene)/RuO2·xH2O nanocomposite for supercapacitor

An organic–inorganic poly(3,4-ethylenedioxythiophene) (PEDOT)/RuO₂·xH₂O nanocomposite (approximately 1 wt.% RuO₂) has been successfully prepared for the first time under microwave irradiation within 5 min with power 900 W via in situ chemical polymerization. The morphology and structure of the resultant material is characterized by transmission electron microscope and Fourier transform infrared. Moreover, the electrochemical properties of the synthesized nanocomposite can be controlled by adjusting the annealing temperature, which is definitely illustrated by cyclic voltammetry, galvanostatic charge–discharge, and electrochemical impedance spectra. Electrochemical data have shown that the PEDOT/RuO₂·xH₂O nanocomposite annealed at 150 °C possesses the most favorable charge/discharge ability with a specific capacitance of 153.3 F g⁻¹ at a current density of 150 mA g⁻¹ and the high efficient utilization of PEDOT at various current densities. Furthermore, such composite has a less capacitance degradation of 23.8% after 1,000 continuous cycles. The improved electrochemical performance are mainly attributed to the large electroactive surface of nanocomposite and the existence of amorphous RuO₂·xH₂O particles as well as a synergistic effect of the polymer PEDOT and annealed RuO₂·xH₂O. Thus, the PEDOT/RuO₂·xH₂O nanocomposite annealed at 150 °C can act as a promising electroactive material for supercapacitor application.     

Multiplex sensor for detection of different metal ions based on on–off of fluorescent gold nanoclusters

In this study, a multiplex fluorescence sensor for successive detection of Fe³⁺, Cu²⁺ and Hg²⁺ ions based on “on–off” of fluorescence of a single type of gold nanoclusters (Au NCs) is described. Any of the Fe³⁺, Cu²⁺ and Hg²⁺ ions can cause quenching fluorescence of Au NCs, which established a sensitive sensor for detection of these ions respectively. With the introduction of ethylene diamine tetraacetic acid (EDTA) to the system of Au NCs and metal ions, a restoration of fluorescence may be found with the exception of Hg²⁺. A highly selective detection of Hg²⁺ ion is, thus, achieved by masking Fe³⁺ and Cu²⁺. On the other hand, the masking of Fe³⁺ and Cu²⁺ leads to the enhancement of fluorescence of Au NCs, which in turn provides an approach for successive determination of Fe³⁺ and Cu²⁺ based on “on–off” of fluorescence of Au NCs. Moreover, this assay was applied to the successful detection of Fe³⁺, Cu²⁺ and Hg²⁺ in fish, a good linear relationship was found between these metal ions and the degree of quenched fluorescent intensity. The dynamic ranges of Hg²⁺, Fe³⁺ and Cu²⁺ were 1.96 × 10⁻¹⁰–1.01 × 10⁻⁹, 1.28 × 10⁻⁷–1.27 × 10⁻⁶ and 1.2 × 10⁻⁷–1.2 × 10⁻⁶ M with high sensitivity (the limit of detection of Fe³⁺ 2.0 × 10⁻⁸ M, Cu²⁺ 1.9 × 10⁻⁸ M and Hg²⁺ 2 × 10⁻¹⁰ M). These results indicate that the assay is suitable for sensitive detection of these metal ions even under the coexistence, which can not only determine all three kinds of metal ions successively but also of detecting any or several kinds of metal ions.     

A novel colorimetric and “turn-on” fluorescent sensor for selective detection of Cu2+

In this work, a new highly selective and sensitive fluorescent sensor for detecting Cu²⁺ was developed based on rhodamine fluorophore. It displayed strong fluorescence “turn-on” effect upon addition of Cu²⁺, and possessed the function of naked eye recognition. The fluorescence enhancement also enabled the sensor to quantitatively analyze Cu²⁺ due to the formation of a stable 1:1 metal–ligand complex in a short time, and the complex possesses relatively good pH stability. In addition, the density functional theory calculations were adopted to investigate the molecular orbitals as well as the spatial structure. Simultaneously, the cell imaging and zebra fish experiments provided a broader application prospect in biological system.     

A fluorescence “on–off” sensor for the highly selective and sensitive detection of Cu2+ ion

In an attempt to obtain a model of copper(II) ion-selective sensors, a new 1,8-naphthalimide-based fluorescence chemosensor, N-allylamine-4-[(E)-4-(([2-aminoethyl]imino)methyl) benzene-1,3-diol]-1,8-naphthalimide (NABN), was designed and synthesized. The sensor NABN is fully characterized by melting point analysis, fourier transform infrared spectra, Ultraviolet–visible (UV–vis) spectra, fluorescence spectra, ¹H NMR and ¹³C NMR spectroscopy, and mass spectrometry. NABN showed an unrivaled sensing behavior and an ardent selectivity toward copper(II) ion over other competitive metal ions tested in solution (N,N-Dimethylformamide (DMF)/Tris–HCl buffer, 1:1, v/v, pH = 7.2). The sensor showed a linear fluorescence quenching toward copper(II) ion in the range 0–50 μM, with a detection limit of 1.92 × 10⁻⁷ M estimated. Job's method indicated the formation of a 2:1 coordinative mode of the sensor with copper(II) ion with a high threshold of binding constant of 4 × 10¹² M⁻¹. Combining the above results, the quenching response of NABN toward Cu(II) ions could be ascribed to the strong, intrinsic paramagnetic behavior of Cu(II).     

Improved catalytic activity and N2 selectivity of Fe–Mn–O x catalyst for selective catalytic reduction of NO by NH3 at low temperature

Research on Chemical Intermediates - FeO x , MnO x and Fe–Mn–O x catalysts were prepared by the co-precipitation method and used for the selective catalytic reduction (SCR) of NO x by...     

Electrochemical sensor based on a carbon nanotube-modified imprinted sol–gel for selective and sensitive determination of ß2-agonists

We describe a molecularly imprinted electrochemical sensor for selective and sensitive determination of β₂-agonists. It is making use of a combination of single-wall carbon nanotubes (SWNTs) with a molecularly imprinted sol–gel. The SWNTs were introduced in order to enhance electron transport and sensitivity. The imprinted sol–gel film with its specific binding sites acts as a selective recognition element and as a preconcentrator for β₂-agonists. The morphology of the imprinted film was characterized by scanning electron microscopy. The optimized sensor displays high sensitivity and excellent selectivity for the β₂-agonists as shown for their determination in human serum samples.

A highly selective fluorescent sensor for fluoride anion based on pyrazole derivative: Naked eye “no–yes” detection

A new pyrazole-based fluorescent sensor, 5-amino-3-(5-phenyl-1H-pyrrol-2-yl)-1H-pyrazole-4-carboxamide (compound 1), was studied for fluoride anion (F^?) detection in organic or water-containing solution. This compound displayed both changes in UV–vis absorption and fluorescence emission spectra upon addition of F^?. With increasing of F^?, blue emission intensity increases drastically and reaches saturation with 607-fold enhancement at 424 nm. The results indicate that compound 1 has highly selectivity for fluoride detection over other anions, such as Cl^?, Br^?, I^?, HSO₄^?, H₂PO₄^? and AcO^? in DMSO or aqueous DMSO solutions. ¹H NMR titration and other experiments confirm that the sensing process is mainly from the deprotonation of the pyrazole–NH in compound 1.     

Surface-imprinted core–shell Au nanoparticles for selective detection of bisphenol A based on surface-enhanced Raman scattering

Surface-imprinted core–shell Au nanoparticles (AuNPs) were explored for the highly selective detection of bisphenol A (BPA) by surface-enhanced Raman scattering (SERS). A triethoxysilane-template complex (BPA-Si) was synthesized and then utilized to fabricate a molecularly imprinted polymer (MIP) layer on the AuNPs via a sol–gel process. The imprinted BPA molecules were removed by a simple thermal treatment to generated the imprint-removed material, MIP-ir-AuNPs, with the desired recognition sites that could selectively rebind the BPA molecules. The morphological and polymeric characteristics of MIP-ir-AuNPs were investigated by transmission electron microscopy and Fourier-transform infrared spectroscopy. The results demonstrated that the MIP-ir-AuNPs were fabricated with a 2 nm MIP shell layer within which abundant amine groups were generated. The rebinding kinetics study showed that the MIP-ir-AuNPs could reach the equilibrium adsorption for BPA within 10 min owning to the advantage of ultrathin core–shell nanostructure. Moreover, a linear relationship between SERS intensity and the concentration of BPA on the MIP-ir-AuNPs was observed in the range of 0.5–22.8 mg L⁻¹, with a detection limit of 0.12 mg L⁻¹ (blank ± 3 × s.d.). When applied to SERS detection, the developed surface-imprinted core–shell MIP-ir-AuNPs could recognize BPA and prevent interference from the structural analogues such as hexafluorobisphenol A (BPAF) and diethylstilbestrol (DES). These results revealed that the proposed method displayed significant potential utility in rapid and selective detection of BPA in real samples.     

Designing of LaCrO3 − TiO2 nanocomposites p: n heterojunction-based sensor material for the selective detection of volatile petrol vapors (PV) and CO2 gas vapors

In the present research TiO₂ modified LaCrO₃ nanostructure has been designed by simple sol-gel method. The thick films of TiO₂ with different concentrations with LaCrO₃ were fabricated by using screen printing methodology. In present study, the structural properties of TiO₂ doped LaCrO₃ were confirm by using X-ray diffractometer (XRD). While the morphological properties and surface characteristics of fabricated material analyzed using scanning electron microscopy (SEM). The energy dispersive spectroscopy (EDS) was utilized for chemical composition of the prepared material. Transmission electron microscopy (TEM) confirms the orthorhombic crystal lattice structure and morphology of Ti-doped LaCrO₃. While, Fourier transform infrared (FT-IR) spectroscopy was used to investigate the M ? O bonding vibrational stretching frequencies of LaCrO₃ and TiO₂ materials. The zeta potential was recorded for stability of all Ti doped LaCrO₃ nanostructures. The Brunauer-Emmett-Teller (BET) was analyzed for surface area and pore diameter parameters of the fabricated materials. The fabricated materials were checked for application as a sensor for different pollutant gases like Ethanol, CO₂, NO₂, and petrol vapors. The sensor demonstrates the sensitivity for petrol vapors at 150°C for 0.3 M% TiO₂ doped LaCrO₃. And exceptionally 0.5 M% TiO₂ doped LaCrO₃ sensor showed better response for CO₂. The reproducibility confirms the stability of 0.3 M % TiO₂ doped LaCrO₃ sensor and 0.5 M % TiO₂ doped LaCrO₃ sensor. The rapid response and recovery were recorded for both the sensors viz. 0.3 M % and 0.5 M % TiO₂ doped LaCrO₃.     

Acid–base sensor based on sol–gel encapsulation of bromothymol blue in silica: application for milk spoilage detection

Journal of Sol-Gel Science and Technology - In this work, silica capsules containing bromothymol blue (BTB) were synthesized by a modified Stöber sol–gel method. These silica capsules...     

Rolling cycle amplification based single-color quantum dots–ruthenium complex assembling dyads for homogeneous and highly selective detection of DNA

In this work, a new, label-free, homogeneous, highly sensitive, and selective fluorescent biosensor for DNA detection is developed by using rolling-circle amplification (RCA) based single-color quantum dots–ruthenium complex (QDs–Ru) assembling dyads. This strategy includes three steps: (1) the target DNA initiates RCA reaction and generates linear RCA products; (2) the complementary DNA hybridizes with the RCA products to form long double-strand DNA (dsDNA); (3) [Ru(phen)₂(dppx)]²⁺ (dppx = 7,8-dimethyldipyrido [3,2-a:2′,3′-c] phenanthroline) intercalates into the long dsDNA with strong fluorescence emission. Due to its strong binding propensity with the long dsDNA, [Ru(phen)₂(dppx)]²⁺ is removed from the surface of the QDs, resulting in restoring the fluorescence of the QDs, which has been quenched by [Ru(phen)₂(dppx)]²⁺ through a photoinduced electron transfer process and is overlaid with the fluorescence of dsDNA bonded Ru(II) polypyridyl complex (Ru-dsDNA). Thus, high fluorescence intensity is observed, and is related to the concentration of target. This sensor exhibits not only high sensitivity for hepatitis B virus (HBV) ssDNA with a low detection limit (0.5 pM), but also excellent selectivity in the complex matrix. Moreover, this strategy applies QDs–Ru assembling dyads to the detection of single-strand DNA (ssDNA) without any functionalization and separation techniques.     

Picomolar-sensitive impedimetric sensor for salivary calcium analysis at POC based on SAM of Schiff base–modified gold electrode

Journal of Solid State Electrochemistry - Analysis of saliva is a potential diagnostic tool in the management of human diseases. Analysis of saliva in healthy individuals is vital to comparison in...     

A resonance light scattering sensor based on methylene blue–sodium dodecyl benzene sulfonate for ultrasensitive detection of guanine base associated mutations

A resonance light scattering (RLS) sensor for guanine base associated mutations has been developed on the basis of the high selectivity of methylene blue (MB) for guanine bases in the presence of sodium dodecyl benzene sulfonate (SDBS). MB, when bound to SDBS, underwent a dramatic enhancement of its RLS intensity. However, the addition of double-stranded DNA (dsDNA) and single-stranded DNA (ssDNA) caused the strong RLS intensity of MB-SDBS to decrease, and the RLS intensity of MB-SDBS-ssDNA was much lower than that of MB-SDBS-dsDNA. Consequently, it can be concluded that the binding abilities of MB-SDBS with ssDNA and dsDNA were different. Besides, the experimental results showed that MB-SDBS could bind specifically to oligonucleotides rich in guanine bases. Short DNA targets with sequences related to β-thalassaemia, thrombophilia and psoriasis, all of which are guanine base relevant mutations, were synthesized. It was found that MB-SDBS could recognize the single-base mismatches in the mutational DNA, followed by different RLS signal changes between MB-SDBS-normal DNA systems and MB-SDBS-mutational DNA systems. The ultrasensitive sensor allows simple, rapid, sensitive and selective detection of guanine base associated mutations, indicating its potential application in the medical field.     

Sensitive electrochemical sensor using a graphene–polyaniline nanocomposite for simultaneous detection of Zn(II), Cd(II), and Pb(II)

This work describes the development of an electrochemical sensor for simultaneous detection of Zn(II), Cd(II), and Pb(II) using a graphene–polyaniline (G/PANI) nanocomposite electrode prepared by reverse-phase polymerization in the presence of polyvinylpyrrolidone (PVP). Two substrate materials (plastic film and filter paper) and two nanocomposite deposition methods (drop-casting and electrospraying) were investigated. Square-wave anodic stripping voltammetry currents were higher for plastic vs. paper substrates. Performance of the G/PANI nanocomposites was characterized by scanning electron microscopy (SEM) and cyclic voltammetry. The G/PANI-modified electrode exhibited high electrochemical conductivity, producing a three-fold increase in anodic peak current (vs. the unmodified electrode). The G/PANI-modified electrode also showed evidence of increased surface area under SEM. Square-wave anodic stripping voltammetry was used to measure Zn(II), Cd(II), and Pb(II) in the presence of Bi(III). A linear working range of 1–300 μg L⁻¹ was established between anodic current and metal ion concentration with detection limits (S/N = 3) of 1.0 μg L⁻¹ for Zn(II), and 0.1 μg L⁻¹ for both Cd(II) and Pb(II). The G/PANI-modified electrode allowed selective determination of the target metals in the presence of common metal interferences including Mn(II), Cu(II), Fe(III), Fe(II), Co(III), and Ni(II). Repeat assays on the same device demonstrated good reproducibility (%RSD < 11) over 10 serial runs. Finally, this system was utilized for determining Zn(II), Cd(II), and Pb(II) in human serum using the standard addition method.     

Development of a stable biosensor based on a SiO2 nanosheet–Nafion–modified glassy carbon electrode for sensitive detection of pesticides

SiO₂ nanosheets (SNS) have been prepared by a chemical method using montmorillonite as raw material and were characterized by scanning electron microscopy and X-ray diffraction. SiO₂ nanosheet–Nafion nanocomposites with excellent conductivity, catalytic activity, and biocompatibility provided an extremely hydrophilic surface for biomolecule adhesion. Chitosan was used as a cross-linker to immobilize acetylcholinesterase (AChE), and Nafion was used as a protective membrane to efficiently improve the stability of the AChE biosensor. The AChE biosensor showed favorable affinity for acetylthiocholine chloride and catalyzed the hydrolysis of acetylthiocholine chloride with an apparent Michaelis–Menten constant of 134 μM to form thiocholine, which was then oxidized to produce a detectable and fast response. Based on the inhibition by pesticides of the enzymatic activity of AChE, detection of the amperometric response from thiocholine on the biosensor is a simple and effective way to biomonitor exposure to pesticides. Under optimum conditions, the biosensor detected methyl parathion, chlorpyrifos, and carbofuran at concentrations ranging from 1.0?×?10^?12 to 1?×?10^?10?M and from 1.0?×?10^?10 to 1?×?10^?8?M. The detection limits for methyl parathion, chlorpyrifos, and carbofuran were 5?×?10^?13?M. The biosensor developed exhibited good sensitivity, stability, reproducibility, and low cost, thus providing a new promising tool for analysis of enzyme inhibitors.

2-Aminopyridine derivative as fluorescence ‘On–Off’ molecular switch for selective detection of Fe3+/Hg2+

2-Amino-6-methyl-4-phenyl-nicotinonitrile 1, a 2-aminopyridine-based fluorescent compound, was found to be a fluorescent chemosensor for the detection of Fe³⁺ and Hg²⁺ ions over a number of other metal ions. Compound 1 was synthesized in one step using a multicomponent reaction, and characterized using common spectroscopic tools. During Fe³⁺/Hg²⁺ sensing the compound 1 followed a ‘switch-off’ mechanism. Further, compound 1 could sense Fe³⁺ over Hg²⁺ by its distinct absorption and fluorescence quenching behaviors. 1:1 complex formation of 1 with Fe³⁺ and Hg²⁺ was clearly understood from Job’s plot. The present work brings additional evidence on the importance of multicomponent reactions which could lead to the development of fluorescence chemosensor in one step for the selective detection of biologically important metal ions.     

Sol–gel synthesis of Mn2O3/Al2O3/SiO2 hybrid nanocomposite and application for removal of organic dye

Journal of Sol-Gel Science and Technology - Nanocomposite of Mn2O3/Al2O3/SiO2 was prepared through an in situ sol–gel process, in which Mn2O3 nanocrystals were dispersed in the silica-alumina...