Gas chromatography with ballistic heating and ultrafast cooling of column

An overview of the existing methods for minimization of the analysis time in gas chromatography (GC) is presented and a new system for fast temperature programming and very fast cooling down is evaluated. In this study, a system of coaxial tubes, a heating/cooling module (HC-M), was developed and studied with a capillary column placed inside the HC-M. The module itself was heated by a GC oven and cooled down by an external cooling medium. The HC-M was heated at rates of up to 330 °C min⁻¹ and cooled at the rate of 6000 °C min⁻¹. The GC system was prepared for the next run within a few seconds. The HC-M permits good separation reproducibility, comparable with that of a conventional GC, expressed in terms of relative retention times and peak areas of analytes reproducibilities. The HC-M can be used within any commercial gas chromatograph.     

Repeatability in column preparation of a reversed-phase C18 monolith and its application to separation of tocopherol homologues

This work investigated the repeatability of column preparation for a reversed-phase C18 monolith, namely stearyl methacrylate-co-ethylene glycol dimethacrylate (SMA-EDMA). The columns were thermally polymerised using three commonly available heating devices (GC oven, hot air oven and water bath) and their chromatographic performance evaluated using micro-liquid chromatography for separation of five test compounds. Precision in terms of %RSD of retention times were 9.0, 6.5, and 12.5 using GC oven, hot air oven and water bath, respectively. Between-batch precision for the hot air oven (n = 3 days) was less than 10.4% for retention time. The SMA-EDMA monolith was applied to the separation of tocopherol homologues by capillary electrochromatography. Usually tocopherol homologues cannot be completely separated by conventional reversed-phase C8- or C18-packed bed or C18-silica based monolithic columns. Polymer monolith has been shown to give remarkable selectivity towards the tocopherols compared to the conventional microparticulate phase and silica based monolith. Successful separation of the tocopherol isomers was achieved on the SMA-EDMA monolith without any column modification.     

Fast GC with a Small Volume Column Oven and Low Power Heater

A new apparatus for fast gas chromatography separations is described. It consists of a small volume oven containing a coiled fused silica capillary column that is heated by a flow of hot air. The oven can be heated at rates of 10 °C s^?1 with a 300 W heater. Benchmark studies at various temperature programming rates are described. Retention time relative standard deviations increase with increasing heating rate, but are at most about 1% when an 8 °C s^?1 heating rate is employed. The small size of the column oven makes it possible for it to be attached to a commercial GC instrument through an opening provided for installation of a second injector.     

At-column heating and a resistively heated, liquid-cooled thermal modulator for a low-resource bench-top GC x GC

A transportable GC x GC instrument is under development for on-site applications that would benefit from the enhanced resolution and powers of detection, which can be achieved by this method. In the present study, a low-resource GC x GC instrument using an electrically heated and liquid-cooled single-stage thermal modulator that requires no cryogenic materials is evaluated. The instrument also uses at-column heating, thus eliminating the need for a convection oven to house the two columns. The stainless-steel modulator tube is coated with PDMS, which can be heated to 350 degrees C for sample injection into the second-dimension column. The modulator is cooled to -30 degrees C by a 100 mL/min flow of PEG by means of a commercial liquid chiller and a small recirculating pump. Resistive heating of the modulator tube is provided by a programmable power supply, which uses a voltage program that results in increasing modulator temperature during an analysis. This, together with more rapid cooling by the use of a liquid cooling medium, results in reduced solute breakthrough following each heating cycle as the modulator cools to a temperature where quantitative trapping resumes. As a result, modulated peak widths at half-height of less than 40 ms are observed. Design and performance details are presented along with chromatograms of gasoline and an essential oil sample.     

Fast Temperature Programming in Gas Chromatography using Resistive Heating

The features of a resistive-heated capillary column for fast temperature-programmed gas chromatography (GC) have been evaluated. Experiments were carried out using a commercial available EZ Flash GC, an assembly which can be used to upgrade existing gas chromatographs. The capillary column is placed inside a metal tube which can be heated, and cooled, much more rapidly than any conventional GC oven. The EZ Flash assembly can generate temperature ramps up to 1200°/min and can be cooled down from 300 to 50°C in 30 s. Samples were injected via a conventional split/splitless injector and transferred to the GC column. The combination of a short column (5 m×0.25 mm i. d.), a high gas flow rate (up to 10 mL/min), and fast temperature programmes typically decreased analysis times from 30 min to about 2.5 min. Both the split and splitless injection mode could be used. With n-alkanes as test analytes, the standard deviations of the retention times with respect to the peak width were less than 15% (n = 7). First results on RSDs of peak areas of less than 3% for all but one n-alkane indicate that the technique can also be used for quantification. The combined use of a short GC column and fast temperature gradients does cause some loss of separation efficiency, but the approach is ideally suited for fast screening as illustrated for polycyclic aromatic hydrocarbons, organophosphorus pesticides, and triazine herbicides as test compounds. Total analysis times – which included injection, separation, and equilibration to initial conditions – were typically less than 3 min.     

Towards smaller and faster gas chromatography-mass spectrometry systems for field chemical detection

Gas chromatography-mass spectrometry (GC-MS) is already an important laboratory method, but new sampling techniques and column heating approaches will expand and improve its usefulness for detection and identification of unknown chemicals in field settings. In order to demonstrate commercially-available technical advances for both sampling and column heating, we used solid phase microextraction (SPME) sampling of both water and air systems, followed by immediate analysis with a resistively heated analytical column and mass spectrometric detection. High-concern compounds ranging from 140 to 466 amu were analyzed to show the applicability of these techniques to emergency situations impacting public health. A field portable (about 35 kg) GC-MS system was used for analysis of water samples with a resistively heated analytical column externally mounted as a retrofit using the air bath oven of the original instrument design to heat transfer lines. The system used to analyze air samples included a laboratory mass spectrometer with a dedicated resistive column heating arrangement (no legacy air bath column oven). The combined sampling and analysis time was less than 10 min for both air and water sample types. By combining dedicated resistive column heating with smaller mass spectrometry systems designed specificallyfor use in the field, substantially smaller high performance field-portable instrumentation will be possible.     

Numerical modeling of elution peak profiles in supercritical fluid chromatography. Part I—Elution of an unretained tracer

When chromatography is carried out with high-density carbon dioxide as the main component of the mobile phase (a method generally known as “supercritical fluid chromatography” or SFC), the required pressure gradient along the column is moderate. However, this mobile phase is highly compressible and, under certain experimental conditions, its density may decrease significantly along the column. Such an expansion absorbs heat, cooling the column, which absorbs heat from the outside. The resulting heat transfer causes the formation of axial and radial gradients of temperature that may become large under certain conditions. Due to these gradients, the mobile phase velocity and most physico-chemical parameters of the system (viscosity, diffusion coefficients, etc.) are no longer constant throughout the column, resulting in a loss of column efficiency, even at low flow rates. At high flow rates and in serious cases, systematic variations of the retention factors and the separation factors with increasing flow rates and important deformations of the elution profiles of all sample components may occur. The model previously used to account satisfactorily for the effects of the viscous friction heating of the mobile phase in HPLC is adapted here to account for the expansion cooling of the mobile phase in SFC and is applied to the modeling of the elution peak profiles of an unretained compound in SFC. The numerical solution of the combined heat and mass balance equations provides temperature and pressure profiles inside the column, and values of the retention time and efficiency for elution of this unretained compound that are in excellent agreement with independent experimental data.     

Applications of resistive heating in gas chromatography: A review

Gas chromatography is widely applied to separate, identify, and quantify components of samples in a timely manner. Increasing demand for analytical throughput, instrument portability, environmental sustainability, and more economical analysis necessitates the development of new gas chromatography instrumentation. The applications of resistive column heating technologies have been espoused for nearly thirty years and resistively heated gas chromatography has been commercially available for the last ten years. Despite this lengthy period of existence, resistively heated gas chromatography has not been universally adopted. This low rate of adoption may be partially ascribed to the saturation of the market with older convection oven technology, coupled with other analytical challenges such as sampling, injection, detection and data processing occupying research. This article assesses the advantages and applications of resistive heating in gas chromatography and discusses practical considerations associated with adoption of this technology.     

Studies on cryogenic trapping of solutes during chromatographic elution in capillary gas chromatography

Cryogenic trapping of solutes leads to narrowing of the chromatographic band. By placing the trap at the end of a capillary column, it is possible to study the effectiveness of the trap in terms of producing a sharpened elution profile. The trap may be heated by supplementary heating, but here convective heating from the GC oven is employed simply by turning off the cryogenic coolant. It is estimated that it takes about 50 s for the trap to heat up sufficiently to allow trapped solute to be remobilized, although this depends upon the oven temperature and thermal mass of the trap. It can also be shown that the more volatile solutes mobilize faster from the trap in this particular mode of operation. The recovery of trapped components shows that there is essentially quantitative trapping, and the solutes are trapped just at the leading edge of the trap.     

Fundamental chromatographic equations designed for columns packed with very fine particles and operated at very high pressures. Applications to the prediction of elution times and the column efficiencies

The wall temperatures of three Acquity-BEH-C18columns (2.1 mm x 50, 100, and 150 mm) and the temperature of the incoming eluent were maintained constant at 289 K, using a circulating water heat exchanger. The retention times and the band broadening of naphtho[2,3-a]pyrene were measured for each column as a function of the flow rate applied. Pure acetonitrile was used as the eluent. The flow rate dependence of neither elution volumes nor bandwidths can be accounted for by classical models of retention and HETP, respectively, since these models assume columns to be isothermal. Because the heat generated by friction of the eluent against the column bed increases with increasing flow rate, the column bed cannot remain isothermal at high flow rates. This heat is evacuated radially and/or longitudinally by convection, conduction, and radiation. Radial and axial temperature gradients are formed, which are maximum and minimum, respectively, when the temperature of the column wall is kept uniform and constant. The retention times that we measured match well with the values predicted based on the temperature distribution along and across the column, which we calculated and on the temperature dependence of the retention for the same column operated isothermally (i.e., at very low flow rate). The rate of band spreading varies along non-isothermal columns, so the HETP can only be defined locally. It is a function of the axial coordinate. A new contribution is needed to account for the radial thermal heterogeneity of the column, hence the radial distribution of the flow velocities, which warps the elution band. A new model, based on the general dispersion theory of Aris, allows a successful prediction of the unusually large bandwidths observed with columns packed with fine particles, operated at high flow rates, hence high inlet pressures.     

A general strategy for performing temperature-programming in high performance liquid chromatography--prediction of segmented temperature gradients

In the present work it is shown that the linear elution strength (LES) model which was adapted from temperature-programming gas chromatography (GC) can also be employed to predict retention times for segmented-temperature gradients based on temperature-gradient input data in liquid chromatography (LC) with high accuracy. The LES model assumes that retention times for isothermal separations can be predicted based on two temperature gradients and is employed to calculate the retention factor of an analyte when changing the start temperature of the temperature gradient. In this study it was investigated whether this approach can also be employed in LC. It was shown that this approximation cannot be transferred to temperature-programmed LC where a temperature range from 60°C up to 180°C is investigated. Major relative errors up to 169.6% were observed for isothermal retention factor predictions. In order to predict retention times for temperature gradients with different start temperatures in LC, another relationship is required to describe the influence of temperature on retention. Therefore, retention times for isothermal separations based on isothermal input runs were predicted using a plot of the natural logarithm of the retention factor vs. the inverse temperature and a plot of the natural logarithm of the retention factor vs. temperature. It could be shown that a plot of lnk vs. T yields more reliable isothermal/isocratic retention time predictions than a plot of lnk vs. 1/T which is usually employed. Hence, in order to predict retention times for temperature-gradients with different start temperatures in LC, two temperature gradient and two isothermal measurements have been employed. In this case, retention times can be predicted with a maximal relative error of 5.5% (average relative error: 2.9%). In comparison, if the start temperature of the simulated temperature gradient is equal to the start temperature of the input data, only two temperature-gradient measurements are required. Under these conditions, retention times can be predicted with a maximal relative error of 4.3% (average relative error: 2.2%). As an example, the systematic method development for an isothermal as well as a temperature gradient separation of selected sulfonamides by means of the adapted LES model is demonstrated using a pure water mobile phase. Both methods are compared and it is shown that the temperature-gradient separation provides some advantages over the isothermal separation in terms of limits of detection and analysis time.     

直热式毛细管柱对直馏汽油组成的分析

采用柱内电阻丝加热升温的直热式１３Ｘ分子筛薄层毛细管填充柱分析汽油的族组成。分析时间比炉温加热短５０ｍｉｎ,定量分析结果与炉温加热和多孔层开管柱基本相同。保留时间的相对偏差小于３％,直馏汽油中绝大部分组分定量结果的相对偏差小于５％。     

Comparison of Thermal Sweeper and Cryogenic Modulator Technology for Comprehensive Gas Chromatography

The two current technologies for achieving comprehensive gas chromatography (GC×GC) – the thermal sweeper and the cryogenic modulator – are compared in an interlaboratory study using a multicomponent semi‐volatile aromatic compound sample. The same column set (phases, film thickness, dimensions of columns) and conditions of oven temperature program were used. Carrier gas flow settings however were different for the data reported here. The thermal sweeper has a longer overall length due to the extra ca. 30 cm length of narrow bore tubing used for the modulator/accumulator section. Data reveal that the two methods behave in an analogous manner in respect of delivering GC×GC results, with key peak parameters of peak widths and symmetry measures showing good correlation. Retention time dissimilarity on the first dimension columns in the two systems arises from different flow rates used, however the second column retention is similar, and this is due to the resulting different elution temperatures that peaks elute on the first dimension in each system. Overall, the two approaches to GC×GC appear to produce equivalent results within the scope of the application studied. Each system does have its experimental limitations; the thermal sweeper has what may be called a ‘thick film effect’, where at high temperature it can be difficult to sufficiently trap the migrating bands in the accumulator column, and the pulsing of solutes in the cryogenic system may suffer from a ‘thick wall effect’ if a column with too thick a wall dimension is used at low oven temperature.     

Fast temperature programming in routine analysis of multiple pesticide residues in food matrices

Flash gas chromatographic (GC) analysis of 15 organophosphorus pesticides commonly occurring in food crops was performed using the Thermedics Detection EZ Flash upgrade kit installed in the oven of a HP 5890 Series II Plus gas chromatograph. The temperature program and splitless time period were the main parameters to be optimized. In the first set of experiments wheat matrix-matched standards were analyzed both by: (i) the flash GC technique (resistive heating of a 5 m capillary column), and (ii) the conventional GC technique (moderate oven temperature programming of a 30 m capillary column). Using the flash GC technique, the analysis time was reduced by a factor of more than 10 compared to the conventional GC technique. Dramatically improved detectability of analytes was achieved due to much narrower peak widths. The flash GC technique was compared with another approach to faster GC analysis employing a 5 m column and fast temperature programming with a conventional GC oven. In comparison with this alternative, in the case of flash GC significantly better retention time repeatability was observed. The other superiority of resistive heating is very rapid cooling down (i.e., equilibration to the initial conditions) which contributes to the increased sample throughput.     

Carbon dioxide modified subcritical water chromatography

A novel method of increasing the elution strength in subcritical water chromatography (SWC) by adding CO2 to the water mobile phase is presented. Since the polarity of water reduces dramatically with increasing temperature, this property is used in SWC to create an isocratic mobile phase with tunable elutropic strength in reversed-phase separations. Unfortunately, thermal stability of the stationary phase dictates the upper temperature limit and therefore also the minimum available mobile phase polarity. As a result SWC is often not very effective at eluting non-polar analytes. However, when CO2 is blended into subcritical water, a considerable reduction in mobile phase polarity results and improves such separations. For example, in conventional SWC 1-octanol is not observed to elute from a PRP-1 column after several hours at the maximum column temperature of 200 degrees C. In contrast to this, when CO2 is present at 180atm (1atm=101325Pa) in the mobile phase, 1-octanol elutes with good peak shape in less than 4min at only 100 degrees C. The technique is applied to the separation of a variety of analytes which have previously been challenging or even not possible to analyze by conventional SWC. Further, the ability to use temperature and composition programming with the blended CO2/water mobile phase in SWC is also presented and discussed. Overall, the developed method considerably extends the range of non-polar analytes amenable to SWC analysis, while maintaining the beneficial conventional SWC features of flame ionization detection and environmental compatibility.     

Determination of the boiling-point distribution by simulated distillation from n-pentane through n-tetratetracontane in 70 to 80 seconds

This work presents the carrying out of boiling-point distributions by simulated distillation with direct-column heating rather than oven-column heating. Column-heating rates of 300 degrees C/min are obtained yielding retention times of 73 s for n-tetratetracontane. The calibration curves of the retention time versus the boiling point, in the range of n-pentane to n-tetratetracontane, are identical to those obtained by slower oven-heating rates. The boiling-point distribution of the reference gas oil is compared with that obtained with column oven heating at rates of 15 to 40 degrees C/min. The results show boiling-point distribution values nearly the same (1-2 degrees F) as those obtained with oven column heating from the initial boiling point to 80% distilled off. Slightly higher differences are obtained (3-4 degrees F) for the 80% distillation to final boiling-point interval. Nonetheless, allowed consensus differences are never exceeded. Precision of the boiling-point distributions (expressed as standard deviations) are 0.1-0.3% for the data obtained in the direct column-heating mode.     

Numerical modeling of the elution peak profiles of retained solutes in supercritical fluid chromatography

In supercritical fluid chromatography (SFC), the significant expansion of the mobile phase along the column causes the formation of axial and radial gradients of temperature. Due to these gradients, the mobile phase density, its viscosity, its velocity, its diffusion coefficients, etc. are not constant throughout the column. This results in a nonuniform flow velocity distribution, itself causing a loss of column efficiency in certain cases, even at low flow rates, as they do in HPLC. At high flow rates, an important deformation of the elution profiles of the sample components may occur. The model previously used to account satisfactorily for the retention of an unsorbed solute in SFC is applied to the modeling of the elution peak profiles of retained compounds. The numerical solution of the combined heat and mass balance equations provides the temperature and the pressure profiles inside the column and values of the retention time and the band profiles of retained compounds that are in excellent agreement with independent experimental data for large value of mobile phase reduced density. At low reduced densities, the band profiles can strongly depend on the column axial distribution of porosity.     

Fast Capillary Gas Chromatography: Comparison of Different Approaches

Savings in analysis time in capillary GC have always been an important issue for chromatographers since the introduction of capillary columns by Golay in 1958. In laboratories where gas chromatographic techniques are routinely applied as an analytical technique, every reduction of analysis time, without significant loss of resolution, can be translated into a higher sample throughput and hence reduce the laboratory operating costs. In this contribution, three different approaches for obtaining fast GC separations are investigated. First, a narrow-bore column is used under conventional GC operating conditions. Secondly, the same narrow-bore column is used under typical fast GC conditions. Here, a high oven temperature programming rate is used. The third approach uses a recent new development in GC instrumentation: Flash-2D-GC. Here the column is placed inside a metal tube, which is resistively heated. With this system, a temperature programming rate of 100°/s is possible. The results obtained with each of these three approaches are compared with results obtained on a column with conventional dimensions. This comparison takes retention times as well as plate numbers and resolution into consideration.     

Retention time locking procedure for comprehensive two-dimensional gas chromatography

In gas chromatography (GC) reproducible retention times are in many cases highly favorable or in some cases even required. In one-dimensional GC, retention time shifts can be eliminated or minimized using a procedure called retention time locking (RTL). This procedure is based on adjusting the (constant) column head pressure. Unfortunately, this RTL procedure cannot be used in comprehensive two-dimensional gas chromatography (GC × GC) given the fact that peaks will shift in both dimensions. Adjusting the column head pressure in GC × GC will only minimize or eliminate the primary retention time shifts. In this paper, a fast and easy to perform, two-step retention time locking procedure for two-dimensional gas chromatography (2D-RTL) is proposed and its feasibility is demonstrated. This 2D-RTL procedure involves adjustment of the column head pressure or constant column flow, followed by the adjustment of the so-called effective secondary column length. The secondary column length is increased or decreased, simply by moving it stepwise through the modulator. It is demonstrated that retention time shifts in both the primary- and secondary-dimension, which may occur after e.g. replacing the column set, can be minimized to less than half peak base width. The proposed 2D-RTL procedure is used successfully for approximately 1 year in our laboratory.     

Superheated water chromatography of low molecular weight polyethylene glycols with ultraviolet detection.

Superheated water chromatography (SWC) with ultraviolet detection was applied to the separation of low molecular weight polyethylene glycols (PEGs). PEG oligomers could be detected sensitively when the detection wavelength was set at 190 nm. The effect of column temperature on the separation of PEG oligomers was investigated. The elution time of all PEG oligomers decreased with increase in the column temperature; linear relationships were obtained between ln k and 1/T. A temperature-programmed SWC separation enabled the baseline separation of a PEG 200 sample within 50 min.