高分子螯合剂的分析化学中的应用

自伦琴发现Ｘ射线一个世纪以来，核辐射和核技术已广泛应用于人类社会生活和经济发展的各个方面，并了放射科学领域的深入研究。代水平辐射对健康的影响倍受重视，其中对辐射致癌的危险尤为关注。辐射致癌有无阈值，既涉及放射生物学理论，又关系辐射防护实践。辐射兴奋效应的研究获得了日益增多的科学证据，对辐射致癌的“无阈”假说提出了疑问。     

分散液-液微萃取-气相色谱/质谱联用法测定机械加工水基切削液及其废水中的三氯苯

建立了以丙酮为分散剂、氯苯为萃取剂,采用分散液-液微萃取、气相色谱/选择离子质谱联用测定机械加工水基切削液及其废水中三氯苯的方法。该方法与顶空萃取、液-液萃取和固相萃取结合气相色谱/电子捕获检测法相比,具有线性范围广、富集倍数高、重现性好、操作简便、干扰小等优点。样品中三氯苯的加标回收率为94.7％~104.3％,相对标准偏差为2.3％～7.8％。三氯苯的3种同分异构体1,3,5-,1,2,4-和1,2,3-三氯苯的检出限分别为2.0,6.0和3.0 μg/L。重点探讨了萃取剂和分散剂的种类、体积、萃取时间和盐效应等对三氯苯萃取效率的影响,优化了萃取条件。考察了机械加工水基切削液中常用的添加剂对检测结果的影响,结果表明1.0％的亚硝酸钠和聚乙二醇对三氯苯的检测基本无影响。采用该方法对4种实际样品中的三氯苯进行了测定,其中两个样品中含有三氯苯,质量浓度范围为0.15～1.67 mg/L。     

固相微萃取技术及其在炸药检测中的应用

评述了固相微萃取技术的工作原理、操作模式、影响因素,介绍了固相微萃取技术在炸药分析如炸药蒸气分析和炸药残留分析中的应用情况,展望了这一技术的应用前景.     

小肽的合成及其作为双功能螯合剂在诊断用放射性药物中的应用

采用液相合成方法,以很高的纯度和较高的收率合成了3个新的4肽化合物MAG3-Phe-OH,MAG3-Leu-OH和MAG3-Tyr-OH。它们在温和的条件下很容易用99mTc进行标记,并在体内外显示了很高的稳定性。标记物的兔子显象显示新的标记物与99mTc MAG3有不同的代谢途径,有可能对癌细胞有较好的亲合作用而用于肿瘤显像。     

有应用前景的低感高能炸药研究进展

概述了有应用前景的高能低感炸药的研究成果,从改善现有高能炸药晶体品质和合成新的高能低感炸药方面,总结了大幅度降低炸药冲击波感度的研究现状。     

高分子螯合剂在分析化学中的应用

本文综合报导了近１０年来，我们以球形大孔聚氯乙烯树脂、聚丙烯腈纤维、聚氯乙烯纤维、二氧化硅为载体合成了新的高分子螯合剂，并用于各种金属离子的富集，分离，同时又用于化学修饰电极的研究。均取得了满意的结果。     

螯合剂对结合在人血清白蛋白(HSA)上的铜离子活动化能力的研究

用凝胶色谱法研究了螯合剂使结合在人血清白蛋白上的铜(Ⅱ)活动化的能力,若用在螯合剂存在时和无螯合剂存在时蛋白部分结合金属量之比作为表征活动化能力的参数,有如下顺序:Trien>DTPA>EDTA>EGTA>NTA>IDA除Trien和DTPA外,其他几种螯合剂的活动化能力的对数值与其相应的条件稳定常数的对数值之间有一线性关系.Trien和DTPA的反常被认为与复杂的反应历程有关,这可能涉及三元配合物的形成。     

离子色谱法检验液体炸药爆炸尘土中的肼离子

建立了离子色谱检测液体炸药爆炸尘土中肼离子的方法。用去离子水超声提取尘土样品中的肼离子,离心后取上清液并将其分别过OnGuardⅡ RP小柱和0.22 μm过滤膜,经IonPac CS-12A阴离子色谱柱(250 mm×4 mm)分离,采用5 mmol/L甲基磺酸等度淋洗,0.1 mol/L NaOH溶液柱后加碱,金电极安培检测器检测。结果表明,肼离子质量浓度在0.02~2.0 mg/L范围内的线性关系良好(相关系数r²=0.9997)。以信噪比(S/N)为3确定方法检出限为5.0 μg/L, S/N为10确定方法定量限为16.6 μg/L。方法回收率在95.4%~99.1%之间,相对标准偏差(RSD, n=5)在2.1%~3.3%之间。应用该方法检测液体炸药爆炸尘土中肼离子的含量为10.3 mg/kg。该方法操作简便,结果准确,适用于液体炸药爆炸尘土中肼离子的定量检测,满足刑事物证鉴定工作的需要。     

微波辐射技术在1,4,7,10-四氮杂环十二烷四乙酸合成中的应用

应用微波技术合成了1,4,7,10-四氮杂环十二烷四乙酸的关键中间体———1,4,7,10-四氮杂环十二烷盐酸盐。与传统的实验方法相比,该方法反应时间缩短了4 000倍且收率从70%增至88%。     

Obtainment of chelating agents through the enzymatic oxidation of lignins by phenol oxidase

Oxidation of lignin obtained from acetosolv and ethanol/water pulping of sugarcane bagasse was performed by phenol oxidases: tyrosinase (TYR) and laccase (LAC), to increase the number of carbonyl and hydroxyl groups in lignin, and to improve its chelating capacity. The chelating properties of the original and oxidized lignins were compared by monitoring the amount of Cu²⁺ bound to lignin by gel permeation chromatography. The Acetosolv lignin oxidized with TYR was 16.8% and with LAC 21% higher than that of the original lignin. For ethanol/water lignin oxidized with TYR was 17.2% and with LAC 18% higher than that of the original lignin.     

Synthesis of bifunctional chelating agents based on mono and diphosphonic derivatives of diethylenetriaminepentaacetic acid

Bifunctional chelating agents (BFCAs) are small molecules containing a chelating unit, able to strongly coordinate a metal ion, and a reactive functional group, devised to form a stable covalent bond with another molecule. BFCAs are widely employed since their conjugation to a suitable biomolecule (e.g., a peptide or an antibody) allows the synthesis of diagnostic or therapeutic agents that specifically target diseased tissue with metals or radiometals. For this reason, BFCAs find application in diagnostic imaging, molecular imaging, and radiotherapy of cancer. The synthesis of new BFCAs based on a diethylenetriaminepentaacetic acid (DTPA) structure in which one or two carboxylic groups are replaced with phosphonic units is described. The phosphonic group, aside from being a classical isostere of the carboxylic acid in coordination chemistry, allows to modulate the physico-chemical properties of the ligands and of the corresponding complexes.     

Efficient and tunable synthesis of new polydentate bifunctional chelating agents using click chemistry

Two novel bifunctional chelating agents, which are bistriazole-based polyaminocarboxylic acids, have been designed and synthesised in high yields. An elegant synthetic approach using the Cu-catalysed azide-alkyne cycloaddition has been developed. This convenient route could be employed for the synthesis of a variety of polydentate bifunctional chelators.     

New chelating agents for colorimetric determination of calcium

Two new calcium chromoionophores2 and3 are described and their potential application to colorimetric determination of calcium is assessed. Chromogenic compound2 bears two acetic acid chelating groups and a 4-(4-nitrophenyl)azophenol chromophore. Its complexation of Ca²⁺ at pH 9.0 is accompanied by a 109-nm bathochromic shift and increase in the absorptivity. Triaryl chromoionophore3 bears two phosphonic acid chelating groups and the same azophenol chromophore. Compound3 exhibits a 107-nm bathochromic shift of the absorption maximum, an increase in the absorptivity upon complexation with Ca²⁺, and good selectivity for Ca²⁺ over Mg²⁺ at pH 7.0. Both chromoionophores exhibit linear responses from 0 to 4×10^–3 M Ca²⁺.     

Evaluation of dithiocarbamates and beta-diketones as chelating agents in supercritical fluid extraction of Cd, Pb, and Hg from solid samples

The use of four dithiocarbamates and three fluorinated β-diketones as potential chelating agents for three transition metal ions (Cd²⁺, Pb²⁺, and Hg²⁺) extracted from spiked sand and filter paper samples by supercritical fluid extraction (SFE) was investigated. The extractions were performed at 45°C and 250 atm for spiked sand samples and at 60°C and 200 atm for filter paper samples using supercritical carbon dioxide modified with 5% methanol. At 250 atm and using carbon dioxide modified with 5% methanol, the recoveries of Cd²⁺, Pb²⁺, and Hg²⁺ ions from spiked sand samples were 95% with lithium bis(trifluoroethyl)dithiocarbamate (LiFDDC) as the chelating agent; they ranged from 83–97% with diethylammonium diethyldithiocarbamate and from 87–97% with sodium di-ethyldithiocarbamate as chelating agents, and from 68–96% with trifluoracetylacetone, hexafluoroacetylacetone, and thenoylfluoroacetone as chelating agents. Ammonium pyrrolidinedithiocarbamate was not effective in the chelation SFE of Cd²⁺, Pb²⁺, and Hg²⁺ ions from either spiked sand or spiked filter paper samples under the extraction conditions used. Supercritical carbon dioxide alone gave consistently lower analyte recoveries than supercritical carbon dioxide modified with 5% methanol. The results suggest that the solubility of the metal chelate in the supercritical fluid plays a more important role than the solubility of the chelating agent in the supercritical fluid, as long as sufficient chelating agent is present in the fluid phase. Fluorination of the chelating agent, as in the case of LiFDDC, increases the solubility of the metal chelate, and subsequently enhances the extraction efficiency for the metal ions.     

Paper chromatography of some chelating reagents containing sulfonic groups in liquid-liquid anion exchange systems

Summary Chromatographic behaviour of nine chelating reagents in chloride and perchlorate systems was investigated with two methods: paper extraction chromatography and moist paper technique. It was found that the affinity of the reagents to cellulose treated with liquid anion exchangers decrease in the following orders: Eriochrome cyanine R>Chromazurol S>Pyrocatechol violet, and Alizarin S>ferron>chromotropic acid nitroso-R-salt>sulfosalicylic acid>tiron. The results obtained suggest that the retention of reagents in extraction chromatography is caused not only by anion-exchange process but also by adsorption and probably also by partition phenomena. The number of alkylammonium cations forming extracted species with reagents depends on the number of sulfonic groups in the reagent molecule but in sulfosalicylic acid carboxylic group can also be partially bound.     

Simultaneous separation and determination of seven chelating agents using high‐performance liquid chromatography based on statistics design

We describe an optimization approach to determine simultaneously occurring chelating agents (glycine, malonic acid, citric acid, glycolic acid, lactic acid, DL‐malic acid, and ethylenediaminetetraacetic acid) in an electroplating effluent using high‐performance liquid chromatography. With chromatography signal area and overall resolution considered as responses, detection conditions were optimized via multiple functions combined with response surface methodology and Plackett–Burman design. Optimized detection conditions were as follows: 15 mmol/L ammonium phosphate buffer (pH 2.5), a 94:6 v/v ratio of ammonium phosphate buffer/acetonitrile, a column temperature of 23.3°C, and a mobile phase flow rate of 1 mL/min. The experimental values conformed to the predicted values and were repeatable (relative standard deviation < 6.4%) and linear (r² > 0.991) over concentration ranges of 1–100 µmol/L. Moreover, the quantification limit (signal‐to‐noise ratio = 10) and the detection limit (signal‐to‐noise ratio = 3) ranged from 0.03 to 0.15 µmol/L and from 0.01 to 0.04 µmol/L, respectively. These results indicate that high‐performance liquid chromatography coupled with statistical design may be a simple and rapid method for simultaneously determining multiple chelating agents in electroplating wastewater effectively.     

Determination of chelating agents in Hanford tank waste simulant by capillary zone electrophoresis

A capillary electrophoretic method has been developed which achieves rapid quantitative separation and determination of ethylenediaminetetraacetic acid, N-(2-hydroxyethyl)ethylenediaminetriacetic acid, diethylenetriaminepentaacetic acid, ethylenediaminediacetic acid, and nitrilotriacetic acid in Hanford tank waste simulant (TWS). Direct UV detection of Cu²⁺/chelator complexes is used to achieve enhanced sensitivity. The qualitative and quantitative reliability of the method and the quality of separations, as given by efficiency and resolution, is presented. In addition, the limits of detection and linearity of detector response with concentration are given for each chelator. The selection of Cu as the UV-absorbing species over other transition metals present in the waste is discussed.     

Determination of synthetic chelating agents in surface and waste water by ion chromatography-mass spectrometry

Coupling of ion chromatography with electrospray mass spectrometry (IC-MS) is a simple, sensitive and quick method for the determination of polar organic traces in water samples without derivatization. Analysis of the chelating agents ethylenediamino tetraacetate (EDTA) and diethylenetriamino pentaacetate (DTPA) in aqueous samples was done by IC-MS on an anion exchange column after simple sample preparation steps. Quantification down to a concentration level of 1 microg L(-1) even in wastewater influents and effluents was achieved utilizing 13C marked internal standards and measuring the individual [M - H+]- and stable [M - 4H+ + Fe3+]- cluster ions. The method was validated against certified, but more time consuming routine methods. Applying this method a series of several European water samples were analyzed for EDTA and DTPA indicating their nature as polar persistent pollutants.