静电自组装方法合成的具有多孔三维网络结构的Fe3O4/石墨烯复合材料作为高性能锂离子电池负极材料

采用静电自组装方法,分两步合成Fe（OH）₃/GO前驱体（GO：氧化石墨烯）,再通过水热反应和600 ℃高纯氮气气氛下煅烧,获得了Fe₃O₄/石墨烯复合材料. 通过X射线衍射（XRD）、扫描电镜（SEM）、高分辨透射电镜（HRTEM）、拉曼（Raman）光谱等多种分析,发现该复合材料具有三维多孔石墨烯网络结构. 把合成的这种Fe₃O₄/石墨烯复合材料作为锂离子电池负极材料,电化学测试结果表明其具有优良的电化学性能：首次放电容量为1390 mAh·g^-1,50次循环后容量为819 mAh·g^-1. 通过对比实验表明,三维石墨烯网络结构的形成对复合材料的电化学循环稳定性起着关键作用.     

Activated carbon/graphene composites with high-rate performance as electrode materials for electrochemical capacitors

Glucose-derived activated carbon (GAC)/reduced graphene oxide (RGO) composites are prepared by pre-carbonization of the precursors (aqueous mixture of glucose and graphene oxide) and KOH activation of the pyrolysis products. The effect of the mass ratio of graphene oxide (GO) in the precursor on the electrochemical performance of GAC/RGO composites as electrode materials for electrochemical capacitors is investigated. It is found that the thermally reduced graphene oxide sheets serves as a wrinkled carrier to support the activated carbon particles after activation. The pore size distribution and surface area are depended on the mass ratio of GO. Besides, the rate capability of GAC is improved by the introduction of GO in the precursor. The highest specific capacitance of 334 F g^?1 is achieved for the GAC/RGO composite prepared from the precursor with a GO mass ratio of 3 %.     

First-Row Transition-Metal Cations (Co2+, Ni2+, Mn2+, Fe2+) and Graphene (Oxide) Composites: From Structural Properties to Electrochemical Applications

Composites of graphene (oxide) (GO) and first-row transition-metal cations (Co²⁺, Ni²⁺, Mn²⁺, Fe²⁺) are prepared by mixing GO and aqueous metal salt solutions. The amount of metal cation bound to GO nanosheets is calculated by using inductively coupled plasma mass spectrometry (ICP-MS) and the possible binding sites of the metals are investigated by means of attenuated total reflectance infrared (ATR-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS) measurements. Electrodes loaded with the metal/GO composites are prepared by a simple drop-casting technique without any binders or conductive additives. The effect of electrochemical reduction on the structure of the composite electrodes is investigated by Raman spectroscopy, XPS, X-ray diffraction (XRD) analysis, and field emission scanning electron microscopy (FESEM). A detailed electrochemical characterization is performed for the utilization of the composite electrodes for electrochemical capacitors and possible oxygen reduction reaction electrocatalysts by cyclic voltammetry (CV) and rotating disk electrode measurements. The highest areal capacitance is achieved with the as-deposited Fe/GO composite (38.7 mF cm⁻² at 20 mV s⁻¹). In the cyclic stability measurements, rCo/GO, rNi/GO, rMn/GO, and rFe/GO exhibit a capacitance retention of 44, 1.1, 73, and 87 % after 3000 cycles of CV at 100 mV s⁻¹, respectively.     

A facile method to prepare graphene-coat cotton and its application for lithium battery

The free-standing and binder-free electrode materials, cotton/graphene (CGN) composites were prepared via a simple “dipping and freeze-drying” process using raw cotton as the supporting body (platform) and graphene oxide (GO) as the suspension. Then the cotton/GO (CGO) composites were annealed at 1000 °C under an Ar flow conditions to obtain CGN composites. The results show that the CGN structure can protect the cotton framework and have better thermal stable property than the cotton alone. Galvanostatic charge–discharge tests demonstrated that the GO concentration had great effects on their electrochemical performances. The CGN (for the GO with 3 and 5 mg ml^?1) provide reversible discharge capacity of 160 mAh g^?1 after 100 cycles, which is about 1.5 times higher than that of the cotton alone (115 mAh g^?1 after 100 cycles). Excellent electrochemical properties of CGN can be ascribed to its controllable structure with more lithium ion storage sites, high electronic conductivity, and fast ion diffusion velocity. The results suggest that this work develops a simple, cheap, and suitable large-scale production method in the lithium-ion batteries.     

氧化石墨烯浓度对还原氧化石墨烯/ZnS电化学性能的影响

以氧化石墨烯(GO)、乙酸锌(Zn(CH₃COO)₂)和硫脲为原料,采用水热法成功制备了还原氧化石墨烯/ZnS(rGO/ZnS)复合材料,并将该材料用作锂离子电池负极。高导电性的 rGO可以为锂离子和电子的传输提供有效的路径,ZnS可以提供较高的理论比容量。rGO/ZnS复合材料在rGO与纳米级高度分散的类球形ZnS颗粒协同作用下展现了较好的嵌锂容量和循环性能。当GO质量浓度为2 mg·mL^-1时制备的rGO/ZnS复合材料的倍率性能最好,循环稳定性最佳。     

氧化石墨烯浓度对还原氧化石墨烯/ZnS电化学性能的影响

以氧化石墨烯(GO)、乙酸锌(Zn(CH₃COO)₂)和硫脲为原料,采用水热法成功制备了还原氧化石墨烯/ZnS(rGO/ZnS)复合材料,并将该材料用作锂离子电池负极。高导电性的 rGO可以为锂离子和电子的传输提供有效的路径,ZnS可以提供较高的理论比容量。rGO/ZnS复合材料在rGO与纳米级高度分散的类球形ZnS颗粒协同作用下展现了较好的嵌锂容量和循环性能。当GO质量浓度为2 mg·mL^-1时制备的rGO/ZnS复合材料的倍率性能最好,循环稳定性最佳。     

Graphene Oxide/Polyacrylamide/Aluminum Ion Cross‐Linked Carboxymethyl Hemicellulose Nanocomposite Hydrogels with Very Tough and Elastic Properties

Development of high‐strength hydrogels has recently attracted ever‐increasing attention. In this work, a new design strategy has been proposed to prepare graphene oxide (GO)/polyacrylamide (PAM)/aluminum ion (Al³⁺)‐cross‐linked carboxymethyl hemicellulose (Al‐CMH) nanocomposite hydrogels with very tough and elastic properties. GO/PAM/Al‐CMH hydrogels were synthesized by introducing graphene oxide (GO) into PAM/CMH hydrogel, followed by ionic cross‐linking of Al³⁺. The nanocomposite hydrogels were characterized by means of FTIR, X‐ray diffraction (XRD), and scanning electron microscopy/energy‐dispersive X‐ray analysis (SEM‐EDX) along with their swelling and mechanical properties. The maximum compressive strength and the Young's modulus of GO_3.5/PAM/Al‐CMH_0.45 hydrogel achieved values of up to 1.12 and 13.27 MPa, increased by approximately 6488 and 18330 % relative to the PAM hydrogel (0.017 and 0.072 MPa). The as‐prepared GO/PAM/Al‐CMH nanocomposite hydrogels possess high strength and great elasticity giving them potential in bioengineering and drug‐delivery system applications.     

Pt‐Pd Bimetallic Nanoparticles Decorated Nanoporous Graphene as a Catalytic Amplification Platform for Electrochemical Detection of Xanthine

The nanoporous graphene papers (NGPs) was prepared by the hard‐template method. The Pt−Pd modified NGPs hybrid was prepared by the self‐assembly method. Then a glassy carbon electrode (GCE) modified with Pt−Pd bimetallic nanoparticles‐functionalized nanoporous graphene composite has been prepared for the electrochemical determination of Xanthine (XA). The Pt−Pd/NGPs hybrid was characterized by transmission electron microscopy, scanning electron microscope and X‐ray diffraction. The electrochemical behavior of XA on Pt−Pd/NGPs/GCE was investigated by cyclic voltammetry and amperometric i‐t. The Pt−Pd/NGPs modified electrode exhibited remarkably electrocatalytic activity towards the oxidation reaction of XA in phosphate buffer solution (pH=5.5). Under the optimal conditions, the determination of XA was accomplished by using amperometric i‐t, the linear response range from 1.0×10⁻⁵∼1.2×10⁻⁴ M. The detection limit was 3.0×10⁻⁶ M (S/N=3). The proposed modified electrode showed good sensitivity, selectivity, and stability with applied to determine XA in human urine.     

A graphene-based real-time fluorescent assay of deoxyribonuclease I activity and inhibition

Using the remarkable difference in the affinity of graphene oxide (GO) with double strand DNA (dsDNA) and short DNA fragments, we report for the first time a GO-based nonrestriction nuclease responsive system. Our system was composed of GO and a fluorescent dye fluorescein amidite (FAM)-labeled dsDNA substrate (F-dsDNA). At first, the fluorescence of this F-dsDNA substrate was quenched upon addition of GO. When nuclease was added to the mixture of dsDNA and GO, hydrolysis of dsDNA was initiated and small DNA fragments were produced. As a result, the short FAM-linked DNA fragments were released from GO due to the weak affinity of GO with short DNA fragments, and the fluorescence got a restoration. At present, many sensing systems are based on the fact that GO prefers to bind long single strand DNA (ssDNA) over dsDNA or short ssDNA. As for our system, GO has a prior binding with dsDNA over short DNA fragments. Compared with previous methods, this assay platform has some advantages. First, since GO can be prepared in large quantities from graphite available at very low cost, this method shows advantages of simplicity and cost efficiency. Besides, the proposed GO-based nuclease assay provides high sensitivity due to the super quenching capacity of GO. Using deoxyribonuclease I (DNase I) as a model system, DNase I activity can be quantitatively analyzed by the velocity of the enzymatic reaction, and 1.75 U mL⁻¹ DNase I can be significantly detected. Moreover, the fluorescent intensity with various concentrations of nuclease becomes highly discriminating after 3–8 min. Thus, it is possible to detect nuclease activity within 3–8 min, which demonstrates another advantage of quick response of the present system. Finally, use of dsDNA as substrate, our method can achieve real-time nuclease activity/inhibition assay, which is time-saving and effortless.     

Facile synthesis of polyaniline/TiO2/graphene oxide composite for high performance supercapacitors

The polyaniline/TiO₂/graphene oxide (PANI/TiO₂/GO) composite, as a novel supercapacitor material, is synthesized by in situ hydrolyzation of tetrabutyl titanate and polymerization of aniline monomer in the presence of graphene oxide. The morphology, composition and structure of the composites as-obtained are characterized by SEM, TEM, XRD and TGA. The electrochemical property and impedance of the composites are studied by cyclic voltammetry and Nyquist plot, respectively. The results show that the introduction of the GO and TiO₂ enhanced the electrode conductivity and stability, and then improved the supercapacitive behavior of PANI/TiO₂/GO composite. Significantly, the electrochemical measurement results show that the PANI/TiO₂/GO composite has a high specific capacitance (1020 F g⁻¹ at 2 mV s⁻¹, 430 F g⁻¹ at 1 A g⁻¹) and long cycle life (over 1000 times).     

Development of a New Label‐free,Indicator‐free Strategy toward Ultrasensitive Electrochemical DNA Biosensing Based on Fe3O4 Nanoparticles/Reduced Graphene Oxide Composite

Electrochemistry offers sensitivity, selectivity and low cost for fabrication of sensors capable of detection of selected DNA targets or mutated genes associated with human disease. In this work, we have developed a novel label‐free, indicator‐free strategy of electrochemical DNA sensor based on Fe₃O₄ nanoparticles/reduced graphene oxide (Fe₃O₄/r‐GO) nanocomposite modified electrode. By using Fe₃O₄/r‐GO nanocomposite as a substrate to immobilize probe DNA and subsequent hybridization with target sequence to form dsDNA, a great signal amplification was achieved through measuring changes in DPV peak current of underlying Fe(II)/Fe(III) redox system. With the remarkable attomolar sensitivity and high specificity and at the same time, great simplicity, the proposed strategy may find great applications in different DNA assay fields.     

Engineering Na−Mo−O/Graphene Oxide Composites with Enhanced Electrochemical Performance for Lithium Ion Batteries

Sodium molybdate (Na−Mo−O) wrapped by graphene oxide (GO) composites have been prepared via a simple in-situ precipitation method at room temperature. The composites are mainly constructed with one dimension (1D) ultra-long sodium molybdate nanorods, which are wrapped by the flexible GO. The introduction of GO is expected to not merely provide more active sites for lithium-ions storage, but also improve the charge transfer rate of the electrode. The testing electrochemical performances corroborated the standpoint: The Na−Mo−O/GO composites delivers specific capacities of 718 mAh g⁻¹ after 100 cycles at 100 mA g⁻¹, and 570 mAh g⁻¹ after 500 cycles at a high rate of 500 mA g⁻¹; for comparison, the bare Na−Mo−O nanorod shows a severe capacity decay, which deliver only 332 mAh g⁻¹ after 100 cycles at 100 mA g⁻¹. In view of the cost-efficient and less time-consuming in synthesis, and one-step preparation without further treatment, these Na−Mo−O nanorods/GO composites present potential and prospective anodes for LIBs.     

Synthesis and characterization of graphene oxide‐based hybrid ligand and its metal complexes: Highly efficient sensor and catalytic properties

A new graphene oxide‐based hybrid material (HL) and its Co(II), Cu(II) and Ni(II) metal complexes were prepared. Firstly, graphene oxide and (3‐aminopropyl)trimethoxysilane were reacted to give graphene oxide–3‐(aminopropyl)trimethoxysilane (GO‐APTMS) hybrid material. After that, hybrid material HL was synthesized from the reaction of GO‐APTMS and 2,6‐diformyl‐4‐methylphenol. Finally, Co(II), Cu(II) and Ni(II) complexes of HL were obtained. All the materials were characterized using various techniques. The chemosensor properties of HL were investigated against Na⁺, K⁺, Cd²⁺, Co²⁺, Cu²⁺, Hg²⁺, Ni²⁺, Zn²⁺, Al³⁺, Cr³⁺, Fe³⁺ and Mn³⁺ ions and it was found that HL has selective chemosensing to Fe³⁺ ion. All the graphene oxide‐supported complexes were used as heterogeneous catalysts in the oxidation of 2‐methylnaphthalene (2MN) to 2‐methyl‐1,4‐naphthoquinone (vitamin K₃, menadione) in the presence of hydrogen peroxide, acetic acid and sulfuric acid. The Cu(II) complex showed good catalytic properties compared to the literature. The selectivity of 2MN to vitamin K₃ was 60.23% with 99.75% conversion using the Cu(II) complex.     

Simple and label-free electrochemical assay for signal-on DNA hybridization directly at undecorated graphene oxide

Exploring graphene oxide (GO), DNA hybridization detection usually relies on either GO decoration or DNA sequences labeling. The former endows GO with desired chemical, optical, and biological properties. The latter adopts labeled molecules to indicate hybridization. In the present work, we propose a simple, label-free DNA assay using undecorated GO directly as the sensing platform. GO is anchored on diazonium functionalized electrode through electrostatic attraction, hydrogen bonding or epoxy ring-opening. The π–π stacking interaction between hexagonal cells of GO and DNA base rings facilitates DNA immobilization. The adsorbed DNA sequence is specially designed with two parts, including immobilization sequence and probe sequence. In the absence of target, the two sequences lie nearly flat on GO platform. In the presence of target, probe hybridizes with it to form double helix DNA, which ‘stands’ on GO. While the immobilization sequence part remains ‘lying’ on GO surface. Hence, DNA hybridization induces GO interfacial property changes, including negative charge and conformational transition from ‘lying’ ssDNA to ‘standing’ dsDNA. These changes are monitored by electrochemical impedance spectroscopy and adopted as the analytical signal. This strategy eliminates the requirement for GO decoration or DNA labeling, representing a comparatively simple and effective way. Finally, the principle is applied to the detection of conserved sequence of the human immunodeficiency virus 1 pol gene fragment. The dynamic detection range is from 1.0 × 10⁻¹² to 1.0 × 10⁻⁶ M with detection limit of 1.1 × 10⁻¹³ M with 3σ. And the sequences with double- or four-base mismatched are readily distinguishable. In addition, this strategy may hold great promise for potential applications from DNA biosensing to nanostructure framework construction based on the versatile DNA self-assembly.     

Determination of Explosives Using Electrochemically Reduced Graphene

A graphene‐based electrochemical sensing platform for sensitive determination of explosive nitroaromatic compounds (NACs) was constructed by means of electrochemical reduction of graphene oxide (GO) on a glassy carbon electrode (GCE). The electrochemically reduced graphene (ER‐GO) adhered strongly onto the GCE surface with a wrinkled morphology that showed a large active surface area. 2,4‐Dinitrotoluene (2,4‐DNT), as a model analyte, was detected by using stripping voltammetry, which gave a low detection limit of 42 nmol L⁻¹ (signal‐to‐noise ratio=3) and a wide linear range from 5.49×10⁻⁷ to 1.1×10⁻⁵ M . Further characterizations by electrochemistry, IR, and Raman spectra confirmed that the greatly improved electrochemical reduction signal of DNT on the ER‐GO‐modified GC electrode could be ascribed to the excellent electrocatalytic activity and high surface‐area‐to‐volume ratio of graphene, and the strong π–π stacking interactions between 2,4‐DNT and the graphene surface. Other explosive nitroaromatic compounds including 1,3‐dinitrobenzene (1,3‐DNB), 2,4,6‐trinitrotoluene (TNT), and 1,3,5‐trinitrobenzene (TNB) could also be detected on the ER‐GO‐modified GC electrode at the nM level. Experimental results showed that electrochemical reduction of GO on the GC electrode was a fast, simple, and controllable method for the construction of a graphene‐modified electrode for sensing NACs and other sensing applications.     

Syntheses,Characterizations and Adsorption Properties of MIL‐101/Graphene Oxide Composites

Composites of the Cr³⁺‐based metal‐organic framework (MIL‐101) and graphene oxide (GO) have been synthesized with different ratios of MIL‐101 and GO. The composites and the parent material MIL‐101 were characterized by X‐ray diffraction, scanning electron microscopy and nitrogen adsorption. The results indicated that the incorporation of large amounts of GO (10 and 20 wt%) almost did not prevent the formation of MIL‐101 units, but had an obvious impact on the size of MIL‐101 crystals. On the contrary, small amounts of GO added (2 and 5 wt%) prevented significantly the proper assembly of MIL‐101 units, thus resulting in a pronounced decrease in the porosities of composites.     

Synthesis of graphene oxide nanosheet: A novel glucose sensor based on nickel-graphene oxide composite film

The graphene oxide (GO) nanosheets were produced by chemical conversion of graphite, and were characterized by transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FT-IR). An electrochemical sensor based on Ni/graphene (GR) composite film was developed by incorporating Ni²⁺ into the graphene oxide film modified glassy carbon electrode (Ni/GO/GCE) through the electrostatic interactions with negatively charged graphene oxide. The Ni²⁺/graphene modified glassy carbon electrode (Ni/GR/GCE) was prepared by cyclic voltammetric scanning of Ni/GO/GCE in the potential range from ?1.5 to 0.2 V at 50 mV s^?1 for 5 cycles. The electrochemical activity of Ni/GR/GCE was illustrated in 0.10 M NaOH using cyclic voltammetry. The Ni/GR/GCE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple. The introduction of conductive graphene not only greatly facilitates the electron transfer of Ni²⁺, but also dramatically improves the long-term stability of the sensor by providing the electrostatic interactions. Ni/GR/GCE also shows good electrocatalytic activity toward the oxidation of glucose. The Ni/GR/GCE gives a good linear range over 10 to 2700 μM with a detection limit of 5 μM towards the determination of glucose by amperometry. This sensor keeps over 85% activity towards 0.1 mM glucose after being stored in air for a month, respectively. Furthermore, the modified sensor was successfully applied to the sensitive determination of glucose in blood samples.     

Carbon nanotubes/(pLys/dsDNA) n layer-by-layer multilayer films for electrochemical studies of DNA damage

Carboxylic group-functionalized carbon nanotubes (c-CNT) were modified on the surface of carbon paste electrode to obtain a conducting precursor film. Positively charged poly-l-lysine (pLys) and negatively charged double-stranded DNA (dsDNA) were alternately adsorbed on the c-CNT-modified electrode, forming (pLys/dsDNA) _n layer-by-layer (LBL) films. Cyclic voltammetry and electrochemical impedance spectroscopy of the electroactive probe [Fe(CN)₆]^3−/4− could give the valuable dynamic information of multilayer films growth. The oxidative DNA damage induced by cadmium ion (Cd²⁺) in the LBL multilayer films was studied by differential pulse voltammetry (DPV) with methylene violet (MV) as the intercalation redox probe. The electrochemical signals of MV on the multilayer films were effectively amplified via LBL technology. The specific intercalation of MV into dsDNA base pairs and the amplified electrochemical response of MV, combined with the unique feature of loading reversibility of MV in the DNA layer-by-layer films, made the difference in DPV response between the intact, and damaged dsDNA films become pronounced. This biosensor exhibited that the (pLys/dsDNA) _n films could be utilized for investigations of DNA damage.     

功能化石墨烯/聚苯胺复合电极材料的制备和电化学性能

利用水合肼还原十八胺（ODA）接枝的氧化石墨烯（GO）,得到了十八胺功能化石墨烯（ODA-G）,将ODAG与聚苯胺（PANI）通过溶液共混法,制备了功能化石墨烯和聚苯胺纳米复合材料（ODA-G/PANI）. 采用傅里叶变换红外（FTIR）光谱、X射线衍射（XRD）、热重分析（TGA）、拉曼（Raman）光谱及透射电镜（TEM）,对复合材料的结构和形貌进行了表征;利用循环伏安、恒流充放电及交流阻抗谱等,对复合材料的电化学性能进行了测试. 结果显示,少量ODA-G的引入为PANI 的电化学氧化还原反应提供了更多的电子通道和活性位置,有利于提高PANI 的赝电容. 在电流密度1.0 A·g^-1下,2%（w）ODA-G/PANI 的比电容达到787 F·g^-1,而相应的PANI 仅有426 F·g^-1. 此外,ODA-G/PANI的循环稳定性也远高于纯PANI.