Tin oxide coating on polytetrafluoroethylene films in aqueous solutions

Polytetrafluoroethylene (PTFE) films were successfully coated with tin oxide in aqueous solutions. Tin oxide was crystallized in the solution and formed nanocrystal coatings on the polymer films. The coatings consisted of SnO₂ and SnO crystals. They were assemblies of tin oxide nanosheet of about 10 to 50 nm in size and about 5 nm in thickness. The nanocrystal films can be exfoliated from the PTFE substrates. Tin oxide nanocrystal films had a rough liquid surface and a dense substrate‐side surface. Transparency of PTFE films coated with tin oxide was same as that of bare PTFE films in the range from 400 to 800 nm. The PTFE films coated with tin oxide nanocrystals can be pasted on desired substrates. Copyright © 2009 John Wiley & Sons, Ltd.     

Region‐Selective Deposition of Core–Shell Nanoparticles for 3 D Hierarchical Assemblies by the Huisgen 1,3‐Dipolar Cycloaddition

A method for the region‐selective deposition of nanoparticles (NPs) by the Huisgen 1,3‐dipolar cycloaddition is presented. The approach enables defined stacking of various oxide NPs in any order with control over layer thickness. Thereby the reaction is performed between a substrate, functionalized with a self‐assembled monolayer of an azide‐bearing phosphonic acid (PA) and aluminum oxide (AlO_x) NPs functionalized with an alkyne bearing PA. The layer of alkyne functionalized AlO_x NPs is then used as substrate for the deposition of azide‐functionalized indium tin oxide (ITO) NPs to provide a binary stack. This progression is then conducted with alkyne‐functionalized CeO₂ NPs, yielding a ternary stack of NPs with three different NP cores. The stacks are characterized by AFM and SEM, defining the region‐selectivity of the deposition technique. Finally, these assemblies have been tested in devices as a dielectric to form a capacitor resulting in a dramatic increase in the measured capacitance.     

Fluorescent dendritic polymers and nanostructured coatings for the detection of chemical warfare agents and other analytes

Polyamidoamine (PAMAM) dendrimers of generations zero (G0) to four (G4), and a hyperbranched polyurea (HB‐PU), were functionalized with 1,5‐dansyl (1,5‐D), 2,5‐dansyl (2,5‐D), 2,6‐dansyl (2,6‐D) and nitrobenzofurazan (NBD) fluorophores that change their fluorescence emission wavelength in response to chemical environment, and the resulting dendritic polymers were characterized by MALDI‐TOF mass spectrometry, ¹H NMR, ¹³C NMR, and fluorescence spectroscopy. Fluorophore‐functionalized dendritic polymers were then reacted further with 3‐acryloxypropyldimethoxymethylsilane (AOP‐DMOMS) at various fluorophore to DMOMS substitution ratios. The resulting materials were cast onto glass slides, and cured into robust nanostructured coatings. Coatings with 50% fluorophore–50% DMOMS substitution showed the strongest fluorescence and the best physical properties. Coated coupons were tested against a wide range of analytes including the chemical warfare agent simulants dimethyl methylphosphonate (DMMP) and chloroethylethylsulfide (CEES), and the water‐methanol‐ethanol series. It was found that the ability of the coatings to distinguish between analytes decreased with increasing cross‐link density for both dendrimer and hyperbranched polymer‐based coatings. It was also found that the percent fluorophore substitution and the type of dendritic polymer carrying the fluorophore had no significant effect upon fluorescence emission wavelength, but fluorescence emission wavelength became less dependent upon solvent with increasing dendrimer generation and molecular mass. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5101–5115, 2009     

Synthesis and ring‐opening polymerization of new monoalkyl‐substituted lactides

New monoalkyl‐substituted lactides were synthesized by reaction of α‐hydroxy acids with 2‐bromopropionyl bromide, and polymerized with various catalysts in the presence of benzyl alcohol by ring‐opening polymerization (ROP). The classic tin(II) 2‐ethylhexanoate (Sn(Oct)₂) catalyst was leading to polymers with narrow distribution and predictable molecular weights, in polymerizations in bulk or toluene at 100 °C. The polymerization rate was corresponding to the steric hindrance of the alkyl substituents, such as butyl, hexyl, benzyl, isopropyl, and dimethyl groups. A yield of 83% was obtained with the hexyl‐substituted lactide after 1 h of polymerization. Excellent conversions (97%) could be achieved by using the alternative catalyst 4‐(dimethylamino)pyridine (DMAP). This latter organic catalyst was most efficient in polymerizing the more steric‐hindered lactides with good molecular weight and polydispersity control, in comparison to the tin(II) 2‐ethylhexanoate and tin(II) trifluoromethane sulfonate [Sn(OTf)₂] catalysts. The efficiency of the DMAP catalyst and the variability of the monomer synthesis route for new alkyl‐substituted lactides allow to prepare and to envision a wide range of new functionalized polylactides for the elaboration of tailored materials. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4379–4391, 2004     

Electrical and optical properties of ceramic–polymer nanocomposite coatings

Transparent, conductive composite coatings were fabricated from suspensions of poly(vinyl acetate‐acrylic) (PVAc‐co‐acrylic) copolymer latices (50–600 nm) and nanosized antimony‐doped tin oxide (ATO) particles (～15 nm). The suspensions were deposited as coatings onto poly(ethylene terephthalate) substrates and dried at 50 °C. Microstructure studies using field emission scanning electron microscopy and tapping‐mode atomic force microscopy (TMAFM) indicated that the latex particles coalesced during drying and forced the ATO particles to segregate into the boundaries between the latex particles. Low phase contrast was observed with TMAFM; this result was consistent with the presence of PVAc‐co‐acrylic in the ATO‐rich phase of the composite. The conductivity of the composite coatings followed a percolation power‐law equation, with the percolation threshold between 0.05 and 0.075 volume fractions of ATO and the critical conductivity exponent ranging from 1.34 to 2.32. The highest direct‐current conductivity of the composite coatings was around 10^?2 S/cm. The optical transmittance and scattering behavior of the coatings were also investigated. Compared with the PVAc‐co‐acrylic coating, the composite coatings had lower transparency because of the Rayleigh scattering. The transparency of the composite coatings was improved by a reduction in the coating thickness. The best transparency for the coatings with a direct‐current conductivity of approximately 10^?2 S/cm was around 85% at a wavelength of 600 nm. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1744–1761, 2003     

Nonenzymatic H2O2 Electrochemical Sensor Based on SnO2‐NPs Coated Polyethylenimine Functionalized Graphene

This paper demonstrated using polyethylenimine (PEI)‐functionalized graphene (Gr) incorporating tin oxide (SnO₂) hybrid nanocomposite as a platform for nonenzymatic H₂O₂ electrochemical sensor. The results of UV‐vis spectroscopy and X‐ray diffraction (XRD) confirmed the simultaneous formation of tin oxide (SnO₂) nanocomposite and reduction of graphene oxide (GO). Transmission electron microscopy (TEM) images showed a uniform distribution of nanometer‐sized tin oxide nanoparticles on the grapheme sheets, which could be achieved using stannous chloride (SnCl₂) complex instead of tin oxide as precursor. The electrochemical measurements, including cyclic voltammetry (CV) and amperometric performance (I‐t), showed that the PEI‐functionalized Gr supported SnO₂ (SnO₂‐PEI‐Gr) exhibited an excellent electrocatalytic activity toward the H₂O₂. The corresponding calibration curve of the current response showed a linear detection range of 9×10⁻⁶∼1.64×10⁻³ mol L⁻¹, while the limit of detection was estimated to be 1×10⁻⁶ mol L⁻¹. Electrochemical studies indicated that SnO₂ and functionalized Gr worked synergistically for the detection of H₂O₂.     

Synthesis of novel hyperbranched polymers featuring oxazoline linear units and their application in fast‐drying solvent‐borne coating formulations

Novel acid‐terminated hyperbranched polymers (HBPs) containing adipic acid and oxazoline monomers derived from oleic and linoleic acid have been synthesized via a bulk polymerization procedure. Branching was achieved as a consequence of an acid‐catalyzed opening of the oxazoline ring to produce a trifunctional monomer in situ which delivered branching levels of >45% as determined by ¹H and ¹³C NMR spectroscopy. The HBPs were soluble in common solvents, such as CHCl₃, acetone, tetrahydrofuran, dimethylformamide, and dimethyl sulfoxide and were further functionalized by addition of citronellol to afford white‐spirit soluble materials that could be used in coating formulations. During end group modification, a reduction in branching levels of the HBPs (down to 12–24%) was observed, predominantly on account of oxazoline ring reformation and trans‐esterification processes under the reaction conditions used. In comparison to commercial alkyd resin paint coatings, formulations of the citronellol‐functionalized hyperbranched materials blended with a commercial alkyd resin exhibited dramatic decreases of the blend viscosity when the HBP content was increased. The curing characteristics of the HBP/alkyd blend formulations were studied by dynamic mechanical analysis which revealed that the new coatings cured more quickly and produced tougher materials than otherwise identical coatings prepared from only the commercial alkyd resins. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3964–3974     

Conductive ATO‐acrylate nanocomposite hybrid coatings: Experimental results and modeling

The electrical volume conductivity σ of antimony‐doped tin oxide (ATO)–acrylate nanocomposite hybrid coatings was investigated. The relation between σ and the volume filler fraction p was analyzed for the ATO‐acrylate coatings containing ATO nanoparticles grafted with different amounts of 3‐methacryloxy‐propyl‐trimethoxy‐silane coupling agent. Percolation thresholds were observed at very low filler fractions (1–2 vol %) for the coatings containing ATO nanoparticles with a low amount of surface grafting. A modified effective medium approximation (EMA) model was introduced. This model takes into consideration different distances between adjacent semiconductive particles in the particle network. The model elucidates how self‐arrangement of the particles influences the location of the percolation threshold in the log σ ? p plot. The modified EMA model can successfully explain the multiple transition behavior and the variable percolation thresholds found for the ATO‐acrylate nanocomposite hybrid coatings. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2147–2160, 2007     

Mechanochemistry Induced Using Force Exerted by a Functionalized Microscope Tip

Atomic‐scale mechanochemistry is realized from force exerted by a C₆₀‐functionalized scanning tunneling microscope tip. Two conformers of tin phthalocyanine can be prepared on coinage‐metal surfaces. A transition between these conformers is induced on Cu(111) and Ag(100). Density‐functional calculations reveal details of this reaction. Because of the large energy barrier of the reaction and the strong interaction of SnPc with Cu(111), the process cannot be achieved by electrical means.     

Hybrid sol–gel based coatings for the protection of historical window glass

Medieval glass is commonly attacked by atmospheric pollutants conveyed by water, triggering the corrosion process. Current conservation strategies aim to maintain window glass in its original context, and so it is necessary to protect it from further degradation. Sol–gel technology is very effective for the preparation of protective films, using Si-alkoxide precursors chemically similar to the substrate. The present work discusses water-repellent hybrid sol–gel coatings made from tetra-ethyl-ortho-silicate with different quantities of Si-alkoxides, functionalized with various alkyl groups. The coatings were deposited using the dip-coating technique and characterized by UV–VIS and FT-IR spectroscopy. Static and dynamic contact angle measurements showed an overall homogeneity of the coatings and indicated improved water-repellency when functionalized by long alkyl chains. The coatings with best performance in terms of transparency and contact angle, and with the lowest organic content, were selected and applied to medieval-like glass samples. Colorimetric characterization was carried out using a spectrophotometric scanner before and after application of the coatings and no significant color changes were found. The electron microscopy images revealed relatively even, crack-free coatings, especially with higher organic contents. Contact angle and colorimetric measurements were repeated after accelerated ageing by exposure to UV light and an SO₂-saturated atmosphere. A significant decrease in the contact angle was observed only for the samples treated at the highest SO₂ concentration. The silica-based materials did not give reaction by-products, were water-repellent, compatible with the substrate, colorless, transparent, and stable under exposure to chemicals and light, thereby satisfying the main requirements for the conservation of Cultural Heritage.     

Catalytic Reduction of Alkyl and Aryl Bromides Using Propan‐2‐ol

Milstein's complex, (PNN)RuHCl(CO), catalyzes the efficient reduction of aryl and alkyl halides under relatively mild conditions by using propan‐2‐ol and a base. Sterically hindered tertiary and neopentyl substrates are reduced efficiently, as well as more functionalized aryl and alkyl bromides. The reduction process is proposed to occur by radical abstraction/hydrodehalogenation steps at ruthenium. Our research represents a safer and more sustainable alternative to typical silane, lithium aluminium hydride, and tin‐based conditions for these reductions.     

Hexagonal‐Shaped Tin Glycolate Particles: A Preliminary Study of Their Suitability as Li‐Ion Insertion Electrodes

Tin glycolate particles were prepared by a simple, one‐step, polyol‐mediated synthesis in air in which tin oxalate precursor was added to ethylene glycol and heated at reflux. Hexagonal‐shaped, micron‐sized tin glycolate particles were formed when the solution had cooled. A series of tin oxides was produced by calcination of the synthesized tin glycolate at 600–800 °C. It was revealed that the micron‐sized, hexagonal‐shaped tin glycolate now consisted of nanosized tin‐based particles (80–120 nm), encapsulated within a tin glycolate shell. XRD, TGA, and FT‐IR measurements were conducted to account for the three‐dimensional growth of the tin glycolate particles. When applied as an anode material for Li‐ion batteries, the synthesized tin glycolate particles showed good electrochemical reactivity in Li‐ion insertion/deinsertion, retaining a specific capacity of 416 mAh g^?1 beyond 50 cycles. This performance was significantly better than those of all the other tin oxides nanoparticles (<160 mAh g^?1) obtained after heat treatment in air. We strongly believe that the buffering of the volume expansion by the glycolate upon Li–Sn alloying is the main factor for the improved cycling of the electrode.     

An ambient self‐curable latex based on colloidal dispersions in water of two functionalized polymers and the thermally reversible crosslinked films generated

An ambient self‐curable latex (ASCL) was prepared by mixing colloidal dispersions in water of a chloromethylstyrene (CMS)‐functionalized polymer and a tertiary‐amine‐functionalized polymer. The two dispersions were obtained via the conventional emulsion copolymerization of CMS and 2‐(dimethylamino)ethylacrylate (DMAEA), respectively, with styrene (St), butyl acrylate (BA), or both. No visible coagulation was observed either in the blends after 6 months of storage or after the latexes were introduced into aqueous media with pHs in the range of 3–11. Continuous, transparent, crosslinked elastic films with smooth surfaces were obtained via casting and drying the ASCL at room temperature, when one or both of the two functional polymer particles contained BA monomeric units. Thermocompression cycles; swelling experiments; solubility tests; and ¹H NMR, IR, DSC, and transmission electron microscopy tests were carried out to investigate the crosslinking and morphology of the films. The following observations were made: (1) the crosslinks in the films were generated via the Menschutkin reaction (quaternization) between the  CH₂‐Cl groups of the CMS containing particles and the amine groups of the DMAEA containing particles; (2) the crosslinked films were thermally remoldable due to reversible decrosslinking (dequaternization) on heating and recrosslinking (requaternization) on cooling; and (3) phase separation in the films was observed when one of the functional polymers (for instance, the nonpolar CMS‐St copolymer) was incompatible with the other one (for instance, the polar BA‐DMAEA copolymer). The present ASCL might be useful in producing water‐borne coatings and adhesives, elastic films, and functional membranes. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 389–397, 2001     

Synthesis and cationic photopolymerization of new fluorinated,polyfunctional propenyl ether oligomers

New fluorinated, polyfunctional propenyl ether functionalized resins were synthesized, and their behavior in cationic photopolymerization was investigated. The photopolymerization proceeded efficiently with a high double‐bond conversion (>90%), giving rise to UV‐cured coatings characterized by low glass‐transition temperatures (?33 °C ≤ glass‐transition temperature ≤ ?15 °C) and hydrophobic surface properties. A fluorinated additive was also employed as a reactive additive in the cationic photopolymerization of trimethylolpropane tripropenyl ether, increasing the double‐bond conversion, polymer network flexibility, thermal stability, and surface hydrophobicity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6943–6951, 2006     

The Sensitized Solid‐Phase Electrochemiluminescence of Electrodeposited Poly‐Luminol/Aniline on AuAg/TiO2 Nanohybrid Functionalized Electrode for Flow Injection Analysis

In this study, a copolymer of luminol with aniline is electrochemically deposited onto the AuAg/TiO₂ nanohybrid functionalized indium tin oxide coated glass. It is used as a reagentless electrochemiluminescent (ECL) electrode for flow‐injection‐analysis (FIA). The properties of this solid phase ECL electrode are characterized by cyclic voltammetry, electrochemical impedance spectroscopy and scanning electron microscopy etc. It has stronger ECL emission, sensitive response for target analytes and excellent stability. The so‐prepared ECL electrode shows sensitive response to reactive oxygen species thereafter to be applied for determination of hydrogen peroxide with FIA mode. Under optimized conditions, a mass detection limit of 0.822 pg of hydrogen peroxide was obtained. Thus the hydrogen peroxide residues in samples were detected with satisfactory result.     

The Synthesis of Quinoline‐based Tin Complexes with Pendant Schiff Bases

Whilst pursuing the synthetic utility of quinoline‐based tin complexes, Me₂Sn(Quin‐NO₂)₂ ( 1 ) and Ph₂Sn(Quin‐NO₂)₂ ( 2 ) (Quin‐NO₂ = 5‐nitroquinolino‐8‐oate) were synthesized bearing coordinatively inert nitro groups. Conventional reduction methodologies successfully converted 1 to Me₂Sn(Quin‐NH₂)₂ ( 3 ) and 2 to Ph₂Sn(Quin‐NH₂)₂ ( 4 ) (Quin‐NH₂ = 5‐aminoquinolino‐8‐oate). The synthetically useful amine groups proved difficult to exploit in the presence of the central tin atom, however, a complete Schiff base functionalized Sn complex of the dimethyltin pro‐ligand Me₂Sn(Quin‐py)₂ ( 6 ) was successfully synthesized from 5‐[(pyridin‐2‐ylmethylene)amino]quinolin‐8‐ol (HQuin‐py; 5 ) in good yield via an alternative strategy exploiting the oxophilic tendencies of tin. All species were fully characterized by NMR (including ¹¹⁹Sn NMR spectroscopy), HR‐ESI MS and single‐crystal X‐ray diffraction, and preliminary studies of their supramolecular potential are also discussed.     

Synergistic effect of functional carbon nanotubes and graphene oxide on the anti‐corrosion performance of epoxy coating

In this work, we reported the synergistic effect of functional carbon nanotubes (CNTs) and graphene oxide (GO) on the anticorrosion performance of epoxy coating. For this purpose, the GO and CNTs were firstly modified by the 3‐aminophenoxyphthalonitrile to realize the nitrile functionalized graphene oxides (GO‐CN) and carbon nanotubes (CNTs‐CN). As modified GO‐CN and CNTs‐CN were characterized and confirmed by Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, and gravimetric analyzer. It was found that about 19 and 24 wt% of 3‐aminophenoxyphthalonitrile were grafted onto the surface of the GO and CNTs, respectively. The electrochemical impedance spectroscopy results showed that the GO‐CN&CNTs‐CN hybrid materials exhibit a remarkable superiority in enhancing the anticorrosion performance of epoxy coatings. Significant synergistic effect of the lamellar structural GO‐CN and CNTs‐CN on the anticorrosion performance of epoxy composite coatings was designed. Besides, the epoxy coating with 1 wt% of the GO‐CN&CNTs‐CN hybrid exhibited the best anticorrosion performance, in which the impedance showed the largest one (immersion in 3.5 wt% of NaCl solution for 168 hr). Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of Sonochemical Treatment Modes on the Electrodeposition of Cu–Sn Alloy from Oxalic Acid Electrolyte

Methods of scanning electron microscopy, potentiodynamic polarization, and X-ray diffraction analysis were used to study the kinetic features of the electrodeposition process of the copper–tin alloy from an oxalic acid electrolyte and analyze the structure, composition, and luster of coatings formed under sonochemical treatment conditions at varied power of the ultrasonic field and current load. The ultrasonic treatment with power of 8–40 W dm^–3 makes it possible to 2–8 times intensify the cathodic process and obtain coatings containing 10–15 wt % tin with luster of 20–40%. The specific content of tin in a coating being formed is nearly independent of the ultrasound power and grows with increasing the cathodic current density.     

Preparation and Characterization of Composites that Contain Small Carbon Nano‐Onions and Conducting Polyaniline

Small multilayer fullerenes, also known as carbon nano‐onions (CNOs; 5–6 nm in diameter, 6–8 shells), show higher reactivity than other larger carbon nanostructures. Here we report the first example of an in situ polymerization of aniline on phenyleneamine‐terminated CNO surfaces. The green, protonated, conducting emeraldine polyaniline (PANI) was directly synthesized on the surface of the CNO. The functionalized and soluble CNO/PANI composites were characterized by TEM, SEM, DSC, Raman, and infrared spectroscopy. The electrochemical properties of the conducting CNO/PANI films were also investigated. In comparison with pristine CNOs, functionalized carbon nanostructures show dramatically improved solubility in protic solvents, thus enabling their easy processing for coatings, nanocomposites, and biomedical applications.     

Syntheses and characterization of functionalized polynorbornene dicarboximides for flexible substrates

In this study, we synthesized polynorbornene (PNB) dicarboximides substituted by monochlorophenyl group (PMCPhNDI) and dichlorophenyl group (PDCPhNDI) via ring‐opening polymerization using a ruthenium catalyst and investigated their thermal, mechanical, and optical properties. We also discussed the performance and application of the functionalized PNB dicarboximide films as flexible substrates for organic light‐emitting devices (OLEDs). The polymer films exhibited good optical transparency with an average transmittance of around 97% in the visible light region and good thermal stability with a 5% degradation temperature of >440°C. The polymers were applied for flexible displays, which were coated on indium tin oxide (ITO) thin films using a radio‐frequency planar magnetron sputtering system with changing the deposition substrate temperatures. A flexible OLED that was fabricated on the ITO‐grown polymer substrates exhibited a performance as comparable to the corresponding ITO‐grown glass substrates. Copyright © 2012 John Wiley & Sons, Ltd.