Complex phase behavior and state of miscibility in Poly(ethylene glycol)/Poly(l‐lactide‐co‐ε‐caprolactone) Blends

A miscibility and phase behavior study was conducted on poly(ethylene glycol) (PEG)/poly(l ‐lactide‐ε‐caprolactone) (PLA‐co‐CL) blends. A single glass transition evolution was determined by differential scanning calorimetry initially suggesting a miscible system; however, the unusual T_g bias and subsequent morphological study conducted by polarized light optical microscopy (PLOM) and atomic force microscopy (AFM) evidenced a phase separated system for the whole range of blend compositions. PEG spherulites were found in all blends except for the PEG/PLA‐co‐CL 20/80 composition, with no interference of the comonomer in the melting point of PEG (T_m = 64 °C) and only a small one in crystallinity fraction (X_c = 80% vs. 70%). However, a clear continuous decrease in PEG spherulites growth rate (G) with increasing PLA‐co‐CL content was determined in the blends isothermally crystallized at 37 °C, G being 37 µm/min for the neat PEG and 12 µm/min for the 20 wt % PLA‐co‐CL blend. The kinetics interference in crystal growth rate of PEG suggests a diluting effect of the PLA‐co‐CL in the blends; further, PLOM and AFM provided unequivocal evidence of the interfering effect of PLA‐co‐CL on PEG crystal morphology, demonstrating imperfect crystallization in blends with interfibrillar location of the diluting amorphous component. Significantly, AFM images provided also evidence of amorphous phase separation between PEG and PLA‐co‐CL. A true T_g vs. composition diagram is proposed on the basis of the AFM analysis for phase separated PEG/PLA‐co‐CL blends revealing the existence of a second PLA‐co‐CL rich phase. According to the partial miscibility established by AFM analysis, PEG and PLA‐co‐CL rich phases, depending on blend composition, contain respectively an amount of the minority component leading to a system presenting, for every composition, two T_g's that are different of those of pure components. © 2013 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 111–121     

The role of cold crystallization of homochiral crystallites in the superb heat resistant poly(lactic acid)

The superb heat resistance poly(lactic acid) (PLA) were prepared by blending PLA and poly(d ‐lactic acid) (PDLA) with various molecular weight (M_n). Formation of the stereocomplex in the blends was confirmed by differential scanning calorimetry and wide‐angle X‐ray diffraction. The results of the heat resistance implied it is possible that elevating the Vicat penetration temperature of PLA up to 150°C by blending with PDLA. The cold crystallization of homochiral crystallites is proven to be the critical factor affecting the heat resistance of PLA. While the PLA or PLA/PDLA blends were heated to cold crystallization temperature of samples, both the crystal content and the rigid amorphous region content are increased due to the cold crystallization and tethering effect, and the stiffness and heat resistance of the sample are improved. The cold crystallization homochiral crystallites kinetics of PLA and PLA/PDLA blends was also studied. The results showed the activation energy (?E) of cold crystallization increased from 120.30 kJ/mol to 144.66 kJ/mol with the increasing of PDLA content from 2% to 10%.     

Enhancing crystallization behavior for optimized performances of poly(TMC‐b‐(LLA‐ran‐GA)) by PDLA/PLLA stereocomplex crystallization

The blends of poly(1,3‐trimethylene carbonate‐b‐(l ‐lactide‐ran‐glycolide)) (PTLG) with poly(d ‐lactide) (PDLA) were prepared via solution‐casting method using CH₂Cl₂ as solvent. The poly(l ‐lactide) (PLLA) segments of PTLG with PDLA chain constructed as stereocomplex structures and growth stereocomplex crystals of PLA (sc‐PLA). The effects of sc‐PLA crystals on thermal behavior, mechanical properties, thermal decomposition of the PTLG/PDLA blends were investigated, respectively. The differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) results showed that the total crystallinity of the PTLG/PDLA blends was increased with the PDLA content increasing. Heterogeneous nucleation of sc‐PLA crystals induced crystallization of the PLLA segments in PTLG. The crystallization temperature of samples shifted to 107.5°C for the PTLG/PDLA‐20 blends compared with that of the PTLG matrix, and decreased the half‐time of crystallization. The mechanical measurement results indicated that the tensile strength of the PTLG/PDLA blends was improved from 21.1 MPa of the PTLG matrix to 39.5 MPa of PTLG/PDLA‐20 blends. The results of kinetics of thermal decomposition of the PTLG/PDLA blends by TGA showed that the apparent activation energy of the PTLG/PDLA blends was increased from 59.1 to 72.1 kJ/mol with the increasing of the PDLA content from 3 wt% to 20 wt%, which indicated the enhancement of thermal stability of the PTLG/PDLA blends by addition of PDLA. Furthermore, the biocompatibility of the PTLG/PDLA blends cultured with human adipose‐derived stem cells was evaluated by CCK‐8 and live/dead staining. The experiment results proved the PTLG/PDLA blends were a kind of biomaterial with excellent physical performances with very low cytotoxicity.     

New approach on the development of plasticized polylactide (PLA): Grafting of poly(ethylene glycol) (PEG) via reactive extrusion

In this work, new ways of plasticizing polylactide (PLA) with low molecular poly(ethylene glycol) (PEG) were developed to improve the ductility of PLA while maintaining the plasticizer content at maximum 20 wt.% PLA. To this end, a reactive blending of anhydride-grafted PLA (MAG-PLA) copolymer with PEG, with chains terminated with hydroxyl groups, was performed. During the melt-processing, a fraction of PEG was grafted into the anhydride-functionalized PLA chains. The role of the grafted fraction was to improve the compatibility between PLA and PEG. Reactive extrusion and melt-blending of neat and modified PLA with PEG did not induce any dramatic drop of PLA molecular weight. The in situ reactive grafting of PEG into the modified PLA in PLA/PEG blends showed a clear effect on the thermal properties of PLA. It was demonstrated by DSC that the mobility gained by PLA chains in the plasticized blends yielded crystallization. The grafting of a fraction of PEG into PLA did not affect this process. However, DSC results obtained after the second heating showed an interesting effect on the T_g when 20 wt.% PEG were melt blended with neat PLA or 10 wt.% MAG-PLA. In the latter case, the T_g displayed by the reactive blend was shifted to even lower temperatures at around 14 °C, while the T_g of neat PLA and PLA blended with 20 wt.% PEG was around 60 and 23 °C, respectively. Regarding viscoelastic and viscoplastic properties, the presence of MAG-PLA does not significantly influence the behavior of plasticized PLA. Indeed, with or without MAG-PLA, elastic modulus and yield stress decrease, while ultimate strain increases with the addition of PEG into PLA.     

X-ray scattering and thermal analysis study of the effects of molecular weight on phase structure in blends of poly(butylene terephthalate) with polycarbonate

Blends of Poly(butylene terephthalate), PBT, with Polycarbonate, PC, were studied for a range of molecular weights and blend compositions. Blends were available in PBT/PC compositions 80/20 and 40/60, and with M_w designated by H (high) or L (low). Samples were prepared by melt crystallization, or by cold crystallization following a rapid quench from the melt. Addition of PC reduces the crystallization kinetics of PBT so that the resulting crystals are more perfect than those which form in the homopolymer. Degree of crystallinity of the blends followed the rank ordering: L/L > L/H > H/L = H/H. The glass transition behavior was investigated using dynamic mechanical analysis (DMA) and modulated differential scanning calorimetry (MDSC). All blends exhibited two glass transitions at intermediate temperatures between the T_gs of the homopolymers, indicating existence of a PBT-rich phase and a PC-rich phase. Blends L/L were most, and H/H the least, miscible. Small-angle X-ray scattering was performed at room temperature on cold crystallized blends, or at elevated temperature during melt crystallization. The long period was consistently larger, and the linear stack crystallinity was consistently smaller, in blends L/L or H/L. These results indicate that in blends containing low M_w PC, there is more PC located within the PBT-rich phase. The long period was consistently smaller in cold crystallized samples, while the linear stack crystallinity was nearly the same, regardless of melt or cold crystallization treatment. Reduction of the average long period in cold crystallized samples could result from crystallization of PBT within the PC-rich phase. This is consistent with thermal analysis results, which indicate that cold crystallized samples have greater overall crystallinity than melt crystallized samples. A hypothetical liquid phase diagram is presented to explain the differences between melt and cold crystallized blends. © 1996 John Wiley & Sons, Inc.     

Highly toughened poly(lactic acid) (PLA) prepared through melt blending with ethylene-co-vinyl acetate (EVA) copolymer and simultaneous addition of hydrophilic silica nanoparticles and block copolymer compatibilizer

In this study, a highly toughened PLA was prepared through physical melt-blending with EVA at the presence of hydrophilic nanosilica and SEBS-g-MA block copolymer compatibilizer. The effect of nanosilica and compatibilizer on the morphology, mechanical properties, and linear rheology of the PLA/EVA blends was also investigated. According to TEM images, nanosilica was selectively located in the PLA matrix while some were placed on the interface between the two polymers as was also predicted by thermodynamic and kinetic analysis. Upon the addition of nanoparticles, the interfacial adhesion between the phases was enhanced and the average droplet size decreased. Interestingly, incorporation of SEBS-g-MA induced morphological changes as the spherical EVA droplets turned into a cylindrical shape. DSC results indicated that blending with EVA copolymer resulted in the reduction of crystallization of PLA matrix; however, the crystallinity increased at the presence of nanoparticles up to 5 wt%. The addition of compatibilizer considerably hindered the crystallization of the PLA phase. PLA/EVA blend containing optimum levels of nanosilica exhibited considerably enhanced tensile toughness, elongation at break, and impact strength. On the other hand, the simultaneous addition of nanoparticles and SEBS-g-MA led to synergistic toughening effects and the compatibilized blend containing nanosilica exhibited excellent impact toughness. For instance, the elongation at break of the compatibilized PLA/EVA blend containing the optimal content of nanosilica was increased from 7% to 121% (compared to neat sample). The notched Izod impact strength was also increased from 5.1 to 65 kJ/m². Finally, the microstructure of the blends was assessed by rheological measurements.     

Tough crystalline blends of polylactide with block copolymers of ethylene glycol and propylene glycol

The effect of crystallinity of polylactide (PLA) on the structure and properties of tough PLA blends with PEG-b-PPG-b-PEG block copolymers was studied. PLA was melt blended with a set of the copolymers with varying ratio of the hydrophilic (PEG) and hydrophobic (PPG) blocks. Although the blend phase structure depended on the copolymer molar mass and PEG content, as well as on the copolymer concentration in the blend, crystallinity also played an important role, increasing the copolymer content in the amorphous phase and enhancing phase separation. The influence of crystallinity on the thermal and mechanical properties of the blends depended on the copolymer used and its content. The blends, with PLA crystallinity of 25 ÷ 34 wt%, exhibited relatively high glass transition temperature ranging from 45 to 52 °C, and melting beginning above 120 °C. Although with a few exceptions crystallinity worsened the drawability and toughness, these properties were improved with respect to neat crystalline PLA in the case of partially miscible blends, in which fine liquid inclusions of the modifier were dispersed in PLA rich matrix. About 20-fold increase of the elongation at break and about 4-fold increase of the tensile impact strength were reached at a small content (10 wt%) of the modifier. Moreover, crystallinity decreased oxygen and water vapor transmission rates through neat PLA and the blend, and the barrier property for oxygen of the latter was better than that of neat polymer.     

Thermal behaviors and characteristics of polylactide/poly(butylene succinate) blend films via reactive compatibilization and plasticization

Polylactide (PLA)/poly(butylene succinate) (PBS) blend films modified with a compatibilizer and a plasticizer were hot‐melted through a twin screw extruder and prepared by hydraulic press. Toluene diisocyanate (TDI) and polylactide‐grafted‐maleic anhydride (PLA‐g‐MA) were used as compatibilizers, while triethyl citrate and tricresyl phosphate acted as plasticizers. The effects of the type and content of compatibilizer and plasticizer on the mechanical characteristics, thermal properties, crystallization behavior, and phase morphology of the PLA/PBS blend films were investigated. Reactive compatibilization at increasing levels of TDI improved the compatibility of the PLA and PBS, affecting the toughness of the films. As evidenced by scanning electron microscope, the addition of TDI enhanced the interfacial adhesion of the blends, leading to the appearance of many elongated fibrils at the fracture surface. Furthermore, PLA/PBS blending with both TDI and PLA‐g‐MA led to an acceleration of the cold crystallization rate and an increment of the degree of crystallinity ( ). Toluene diisocyanate could be a more effective compatibilizer than PLA‐g‐MA for PLA/PBS blend films. The synergistic combination of compatibilizer and plasticizer brought a significant improvement in elongation at break and tensile‐impact toughness of the PLA/PBS blends, compared with neat PLA. Their failure mode changed from brittle to ductile due to the improved compatibility and molecular segment mobility of the PLA and PBS phases. Differential scanning calorimeter results revealed that the plasticizers triethyl citrate and tricresyl phosphate changed the thermal behavior of T_cc and T_m, affecting α′ and α crystal formations. However, these plasticizers only slightly improved the thermal stability of the films.     

Structure and properties of chlorinated polyvinyl chloride graft copolymer with higher property

In this work, maleic anhydride (MAH) was grafted onto chlorinated polyvinyl chloride (CPVC) with high chlorine content (66 wt%) via in‐situ chlorinating graft copolymerization (ISCGC) to obtain the material with improved mechanical strength, softening point, and thermal stability of the material. The structure of the graft product (CPVC‐cg‐MAH) was characterized by FTIR, ¹H NMR, GPC, and UV. CPVC‐cg‐MAH contains less vinylidene chloride (CCl₂) units and double bond than corresponding CPVC. Meanwhile, the number–average molecular weight (M_n) and weight–average molecular weight (M_w) of CPVC‐cg‐MAH are increased, but distribution of molecular weight (M_w/M_n) is decreased. Then, the tensile strength and notched impact strength of CPVC‐cg‐MAH increased by 14.5 and 34.6%, respectively. Furthermore, the results of DMA, DSC, TG, and Vicat softening point showed that the loss peak of CPVC‐cg‐MAH was higher evidently than CPVC and moved to high temperature, the glass transition temperature (T_g) of CPVC‐cg‐MAH was consistent with CPVC, initial weight loss temperature, and maximum weight loss rate temperature of CPVC‐cg‐MAH increased by 7.2°C and 6.1°C, respectively, and the Vicat softening temperature of CPVC‐cg‐MAH increased by 15°C and up to 130°C. Copyright © 2011 John Wiley & Sons, Ltd.     

STUDIES OF THE CRYSTALLIZATION BEHAVIOR IN THE CRYSTALLINE/AMORPHOUS POLYMER BLENDS: POLY(ETHYLENE OXIDE)/POLY(METHYL METHACRYLATE) AND POLY(ETHYLENE OXIDE)/POLY(VINYL ACETATE)

The crystallization process of poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA)and PEO/poly(vinyl acetate) (PVAc) blends has been characterized by Fourier Transform Infrared(FTIR) spectra in conjunction with Differential Scanning Calorimeter (DSC) measurements. Thecrystallinity of PEO varies consistently with PEO content in PEO/PVAc blends and the PEO/PMMAblends containing 50 wt% or less PMMA. For the PEO/PMMA blends containing 60 wt% ormore PMMA, the crystallinity of PEO decreases more than PEO content but develops with crystal-lization time. These results can be explained in terms of difference between the crystallization tem-perature (T_c) and glass transition temperature (T_g) of the blends as a function of content of amorphouscomponent.     

A feasible strategy to constructing hybrid conductive networks in PLA‐based composites modified by CNT‐d‐RGO particles and PEG for mechanical and electrical properties

Carbon nanotubes (CNTs) and reduced graphene oxide (RGO) were successfully assembled by chemical reaction to obtain CNT‐d‐RGO particles. Then, a home‐made dynamic impregnating device was used to prepare hybrid CNT‐d‐RGO/polyethylene glycol (PEG). Next, the different modifiers, including CNTs, GO, CNT‐d‐RGO, PEG, and CNT‐d‐RGO/PEG, were, respectively, added into poly‐(lactic acid) (PLA) matrix via melt‐compounding. The dispersed morphology for these different modifiers within the PLA matrix was confirmed by SEM and TEM observations. Especially, compared with the identical weight ratio of CNT‐d‐RGO, the hybrid CNT‐d‐RGO/PEG within the PLA matrix exhibited an excellent exfoliated and interconnected networks morphology. Moreover, compared with pure PLA, not only the crystallinity of all PLA‐based composites notably improved, but half‐crystallization time was also shortened. Furthermore, despite the addition of different modifiers, the crystal form of PLA‐based composites remained unchanged. Noticeably, compared with those of pure PLA, the tensile stress, strain, and modulus of PLA composite added with CNT‐d‐RGO/PEG increased by 29.4%, 4.1%, and 56.1%, respectively, and the V‐notch impact strength slightly improved. In addition, compared with pure PLA, volume resistivity of the PLA composite added with 1 wt% CNT‐d‐RGO/PEG decreased by 93.1%, and its volume conductivity increased by five orders of magnitude.     

Tri‐block copolymers of polyethylene glycol and hyperbranched poly‐3‐ethyl‐3‐(hydroxymethyl)oxetane through cationic ring opening polymerization

Tri‐block copolymers of linear poly(ethylene glycol) (PEG) and hyperbranched poly‐3‐ethyl‐3‐(hydroxymethyl)oxetane (poly‐TMPO) are reported. The novel dumb‐bell shaped polyethers were synthesized in bulk with cationic ringopening polymerization utilizing BF₃OEt₂ as initiator, via drop‐wise addition of the oxetane monomer. The thermal properties of the materials were successfully tuned by varying the amount of poly‐TMPO attached to the PEG‐chains, ranging from a melting point of 54 °C and a degree of crystallinity of 76% for pure PEG, to a melting point of 35 °C and a degree of crystallinity of 12% for the polyether copolymer having an average of 14 TMPO units per PEG chain. The materials are of relatively low polydispersity, with M_n/M_w ranging from 1.2 to 1.4. The materials have been evaluated for usage with the energetic oxidizer ammonium dinitramide. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6191–6200, 2009     

Kinetics and Mechanism Comparison between Cr/Ti‐Based Bimetallic and Ti‐Based Monometallic Catalysts for Ethylene Polymerization

Two (SiO₂/MgR₂/MgCl₂)·TiCl_x model catalysts are made by refluxing TiCl₄ with 0.35 wt% Cr modified silica gel/alkyl Mg adducts or silica gel/alkyl Mg adducts, which are named as Cr/Ti‐based bimetallic Cat‐1 and Ti‐based monometallic Cat‐2, respectively. The kinetics, active center counting, morphology, and polymer characterizations are studied to disclose the effect of low loading Cr active sites on the Cr/Ti‐based bimetallic Cat‐1 polymerization under mild conditions. The activity of Cat‐1 is 120.4% higher than that of Cat‐2, with a 114.1% higher [C*]/[M] value. Morphology results show the Cat‐1 fragmentation in the first 3 min is highly accelerated, which helps to release buried clustered Ti sites. Differential scanning calorimetry results show that low‐temperature heat absorbing shoulder of polyethylene (PE) from Cat‐2 demonstrates the signal of low crystallinity polymer made by Cat‐2 during the first 60 s, verifying the fluffy polymer in morphology results. GPC results show PE from Cat‐1 has a higher M_w in the first 3 min while a lower M_w in the end. The Cat‐1, which release active sites faster, has a high M_w in the early time. Lower M_w in the 900 s attributes to the effect of relative lower M_w polymer made by Cr sites, compared with Cat‐2.     

Poly(butylene terephthalate)/poly(ε-caprolactone) blends: Influence of PCL molecular mass on PBT melting and crystallization behavior

The isothermal crystallization kinetics and melting behavior of poly(butylene terephthalate) (PBT) in binary blends with poly(ε-caprolactone) (PCL) was investigated as a function of PCL molecular mass by differential scanning calorimetry and optical microscopy. The components are miscible in the melt when oligomeric PCL (M_w = 1250) is blended with PBT, whereas only partial miscibility was found in mixtures with higher molecular mass (M_w = 10,000 and 50,000). The equilibrium melting point of PBT in the homopolymer and in blends with PCL was determined through a non-linear extrapolation of the T_m = f(T_c) curve. The PBT spherulitic growth rate and bulk crystallization rate were found to increase with respect to plain PBT in blends with PCL1250 and PCL10000, whereas addition of PCL50000 causes a reduction of PBT solidification rate. The crystallization induction times were determined by differential scanning calorimetry for all the mixtures through a blank subtraction procedure that allows precise estimation of the crystallization kinetics of fast crystallizing polymers. The results have been discussed on the basis of the Hoffman-Lauritzen crystallization theory and considerations on both the transport of chains towards the crystalline growth front and the energy barrier for the formation of critical nuclei in miscible and partially miscible PBT/PCL mixtures are widely debated.     

Various polycarbonate graft copolymers via diels–alder click reaction

In this work, we used Diels–Alder click reaction for the preparation of various types of aliphatic polycarbonates (PCs). We first prepared a novel anthracene‐functionalized cyclic carbonate monomer, anthracen‐9‐ylmethyl 5‐methyl‐2‐oxo‐1,3‐dioxane‐5‐carboxylate (2), followed by ring‐opening polymerization of this monomer to prepare PC with pendant anthracene groups (PC‐anthracene) using 1,8‐diazabicyclo[5.4.0]undec‐7‐ene (DBU)/1‐(3,5‐bis(trifloromethyl)phenyl)‐3‐cyclohexylthiourea (TU) as the catalyst and benzyl alcohol as the initiator in CH₂Cl₂ at room temperature. Subsequently, the resulting PC‐anthracene (M_n,TDGPC = 6000 g/mol, M_w/M_n = 1.22) was grafted with a linear α‐furan protected‐maleimide terminated‐poly(methyl methacrylate) (PMMA‐MI) (M_n,GPC = 3100 g/mol, M_w/M_n = 1.31), or poly(ethylene glycol) (PEG‐MI) (M_n,GPC = 550 g/mol, M_w/M_n = 1.09), or a mixture of PMMA‐MI and PEG‐MI to yield well‐defined PC graft or hetero graft copolymers, PC‐g‐PMMA (M_n,TDGPC = 59000 g/mol, M_w/M_n = 1.22) or PC‐g‐PEG, or PC‐g‐(PMMA)‐co‐PC‐g‐(PEG) (M_n,TDGPC = 39900 g/mol, M_w/M_n = 1.16), respectively, using Diels–Alder click reaction in toluene at 110°C. The Diels–Alder grafting efficiencies were found to be over 97% using UV spectroscopy. Moreover, the structural analyses and the molecular weights of resulting graft copolymers were determined via ¹H NMR and triple detection GPC (TD‐GPC), respectively. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Controlled release of drug via tuning electrospun polymer carrier

Medicated‐fibers have been obtained through electrospinning after rifampin was dissolved in poly (lactic acid)/chloroform solution. The relationship between polymer variables [such as concentration, molecular weight (M_w), and introducing hydrophilic block] and drug release from the electrospun fibers is disclosed. The results show that polymeric concentration and M_w are crucial for producing the medicated fibers, which influence not only the morphology of the medicated‐fiber but also drug release rate from fiber. At the same M_w, the drug release rate decreases with the increase of spinning concentration. At two different M_w blends, drug release behaviors change. When the low M_w content is in a dominant position, drug release rate depends largely on mixing ratio of two M_w contents; on the other hand, drug release rate is also dependent on concentration of spinning fluid. In addition, the block copolymer [poly‐L ‐lactic acid (PLLA)‐polyethylene glycol‐PLLA] shows faster release rate as compared to homopolymer (PLLA). © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Macromorphology of polypropylene homopolymer tacticity mixtures

The macromorphology of isotactic/atactic (iPP/aPP) and isotactic/syndiotactic (iPP/sPP) polypropylene mixtures is examined by optical microscopy. The spherulitic macrostructure of equimolecular weight [weight‐average molecular weight (M_w) = 200k] iPP/aPP blends is volume‐filling to very high aPP concentrations when the crystallization temperature is 130 °C. Similar spherulitic macrostructures (spherulite size and volume‐filling nature) are observed for iPP homopolymer and a 50/50 iPP/aPP blend at low crystallization temperatures (115–135 °C). At higher crystallization temperatures (140–145 °C), a equimolecular weight (M_w = 200k) 50/50 iPP/aPP blend exhibits nodular texture that blurs the spherulitic boundaries. Double temperature jump experiments show that the nodular texture is due to melt phase separation that develops prior to crystallization. The upper critical solution temperature (UCST) of a 50/50 iPP/aPP blend (M_w = 200k) lies below 155 °C, and the blend is miscible at conventional melt processing temperatures. The UCST behavior is controlled by the blend molecular weight and aPP microstructure. aPP microstructures containing increased isospecific sequencing (although still noncrystalline) exhibit a reduced tendency for phase separation in 50/50 mixtures (M_w = 200k) and the absence of nodular texture at low undercoolings (140–145 °C). Equimolecular weight (M_w = 200k) 50/50 iPP/sPP mixtures exhibit phase‐separated texture at all crystallization temperatures. The size scale of the phase‐separated texture decreases with decreasing crystallization temperature because of a competition between crystallization and phase separation from a melt initially well mixed from the initial solution blending process. Extended melt annealing experiments show that the 50/50 iPP/sPP mixture (M_w = 200k) is immiscible in the melt at conventional melt processing temperatures. The iPP/sPP pair shows a much stronger tendency for phase separation than the iPP/aPP polymer pair. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1947–1964, 2000     

Crystallization and structure formation in polymer blends with strong intermodular interactions: blends of poly(ethylene oxide) and styrene-hydroxystyrene copolymers

Time-resolved synchrotron wide- and small-angle X-ray scattering experiments were used to investigate crystallization behavior and microstructure development of a nearly monodisperse poly(ethylene oxide) [PEO] (M_w = 53,500), and its melt-miscible blends with two fractionated styrene - hydroxystyrene random copolymers [SHS]. PEO crystallization rates decrease significantly in the presence of the melt-miscible SHS copolymers. All low and high molecular weight SHS blends exhibit a crystallization process at relatively short times characterized by large Avrami exponents (n), followed by a dominant process with n near that of neat PEO. A model for the crystallization of these blends is proposed.     

Stereocomplex poly(lactic acid) vascular stents by 3D‐printing with long chain branching structures: Toward desirable crystallization properties and mechanical performance

Using pyromelliticdianhydride (PMDA) and polyfunctional epoxy ether (PFE) as branching agent, long chain branching stereocomplex poly(L‐lactide)s and poly(D‐lactide)s was prepared by reactive processing, respectably. Then stereocomplex poly(lactide)s of long chain branching PLLA and PDLA (sc‐PLA/BA) was prepared by solution blending and its fabricated the vascular stents via 3D‐printing.The effects of branching structure on melt crystallization behavior of sc‐PLA/BA investigated by DSC. The influence of the branching agent content on the crystallization ability of samples shows a bell‐shaped relationship, there is a maximum point when the branching agent content is1.5 wt%. When the branching agent content is less than 1.5 wt%, the crystallization ability of the sample increased with the increasing of branching agent content. When the branching agent content exceeded than 1.5 wt%, the crystallization ability of the samples decreased with branching agent content increasing. Such behavior is as the linear PLA branched to dendrite configuration, the enrichment of segments around branching structure within branched chains promoted its nucleation. But the high degree of branching caused inter‐ or intrachians entanglement which obstructed the segments movement and growth into the crystals. The half‐time of crystallization (t_1/2) of the samples decreased from 6 minutes for initial sc‐PLA/BA‐0 to 3 minutes of sc‐PLA/BA‐1.5 wt% at 163°C. POM results indicated that nucleation density of sc‐PLA/BA significantly increased with the branching agent increasing. Moreover, mechanical testing demonstrated that forming branching structure could be an effective modification of the mechanical properties for sc‐PLA, its tensile strength and modulus increases from 57.3 MPa and 2.02 GPa to 70.4 MPa and 3.31 GPa, respectively. TGA results analyzed by FWO method and Kissinger method, indicated the apparent activation energy of sc‐PLA/BA samples increases from 96.8 to 113.3 kJ/mol, suggesting the improvement of heat resistance. The CCK‐8 assay, ALP assay and cell Live/Dead assay results indicated that sc‐PLA with branching structure presented very low cell cytotoxicity. Therefore, the long chain branching sc‐PLA matrix with branching agent could effectively improve its crystallization abilities, mechanical properties, heat resistance and biocompatibilities.     

Thermal properties of polylactides

A thermal analysis of a series of polylactides (PLA) was carried out based on the number of average molecular mass (M _n), and the nature of isomer (D, L and DL). It is confirmed that the glass transition temperature (T _g) of PLA increased as a function of molecular mass irrespective of isomer type except sample with a high polydispersity index. The melting temperature (T _m) and enthalpy of crystal fusion (ΔH _f) of L-isomer increased as the M _n was increased from 1100 to 27500. The degree of crystallinity (χ_c%) increased as a function of molecular mass. However no crystallization peak was detected in the lower molecular mass range (550–1400). The non-isothermal crystallization behavior of the PLA melt was significantly influenced by the cooling rate. Both D and L isomers exhibited insignificant difference in thermal properties and DL lactides exhibited amorphous behavior at identical molecular masses. Change in microstructure showed significant difference between two isomers. Analysis of the FTIR spectra of these PLA samples in the range of 1200–1230 cm⁻¹ supported DSC observation on crystallinity.