Poly(phenyl methacrylate) and poly(1‐naphthyl methacrylate) prepared in microemulsions

Phenyl methacrylate and 1‐naphthyl methacrylate were polymerized in microemulsions using stearyltrimethylammonium chloride, cetyltrimethylammonium bromide, and a mixture of nonionic Triton surfactants to form latexes that were 20–30 nm in diameter. A temperature of 70 °C was needed to obtain polymers using thermal initiation. The tacticities of poly(phenyl methacrylate) (PPhMA) (55% rr) and poly(1‐naphthyl methacrylate) (P‐1‐NM) (47% rr) were the same as those of the polymers prepared in toluene solutions. The weight average molecular weights were 1 × 10⁶ and 5 × 10⁵ g/mol for PPhMA and P‐1‐NM prepared in microemulsions with very broad distributions. PPhMA samples from microemulsions and solution had the same T_g = 127 °C. P‐1‐NM from microemulsions had T_g = 145–147 °C compared with T_g = 142 °C for P‐1‐NM from solution. The molecular weights and the glass‐transition temperatures of both PPhMA and P‐1‐NM from microemulsions are substantially higher than any previously reported. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 519–524, 2001     

Composites of poly (dimethylsiloxane) and spherically shaped poly (2‐hydroxyethylmethacrylate) particles for biomedical use

Silicone rubbers have shown considerable promise in the biomedical field, but their hydrophobicity leads to serious problems in long‐term implants. In our study, composites of poly (dimethylsiloxane) (PDMS) and spherically shaped poly (2‐hydroxyethylmethacrylate) (PHEMA) microparticles were prepared. Unlike previous silicone hydrogel composites, suspension polymerization was carried out in an aqueous medium to prepare PHEMA particles directly, which avoided the removal of organic phase and give hydrogel particles with high purity. Very fine PHEMA particles with uniform geometry and small size were obtained through various influencing factors during their formation. Through the introduction of PHEMA particles, PDMS matrix was endowed with hydrophilicity to a certain extent. With an increase in hydrogel content, higher swelling ability and surface wettability of the composites were observed. We have also demonstrated that smaller sized particles are more favorable for hydrophilicity improvement. The results of improved swelling ability, surface wettability, and low affinity to lipid show that this composite material is suitable for biomedical use. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and characterization of poly(methyl methacrylate)‐block‐poly(methylphenylsilane)‐ block‐poly(methyl methacrylate) by atom transfer radical polymerization

ABA block copolymers of methyl methacrylate and methylphenylsilane were synthesized with a methodology based on atom transfer radical polymerization (ATRP). The reaction of samples of α,ω‐dihalopoly(methylphenylsilane) with 2‐hydroxyethyl‐2‐methyl‐2‐bromoproprionate gave suitable macroinitiators for the ATRP of methyl methacrylate. The latter procedure was carried out at 95 °C in a xylene solution with CuBr and 2,2‐bipyridine as the initiating system. The rate of the polymerization was first‐order with respect to monomer conversion. The block copolymers were characterized with ¹H NMR and ¹³C NMR spectroscopy and size exclusion chromatography, and differential scanning calorimetry was used to obtain preliminary evidence of phase separation in the copolymer products. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 30–40, 2003     

Fabrication of well‐developed nano‐ribbons composed of hierarchically grown isotactic poly(methyl methacrylate) crystals on substrates

Well‐developed nano‐ribbons composed of isotactic poly(methyl methacrylate) (it‐PMMA) were successfully fabricated on mica via a simple solution‐casting method. Typical morphologies with about 0.6 nm thickness and 30–40 nm widths, thermal stability, and alternative structural analyses suggested that nano‐ribbons were composed of two‐dimensional folded chain crystals of it‐PMMA. Typically, nano‐ribbons were developed by incubating tetrahydrofuran (THF) solutions at 20 °C for at least 2 months, more than equi‐amounts of water were added to incubated THF solutions, and solutions were cast onto mica. It was found that, after the aforementioned incubation of THF solutions, it‐PMMA chains adopted trans‐trans (tt) conformations, which are precursors for it‐PMMA crystals, suggesting that THF is a unique solvent for it‐PMMA. By adding water, a poor solvent for it‐PMMA, to THF solutions, it‐PMMA aggregates formed with several hundreds of nanometer sizes, further promoting an increase in the population of the tt conformation. Nano‐ribbons were similarly formed on silicon wafer substrates, suggesting that hydrophilic substrates were essential for the formation of nano‐ribbons. Interestingly, a modulation of the above described method, with the slight evaporation of THF from a THF/water solution before casting onto mica, succeeded in the development of epitaxially adsorbed nano‐ribbons. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3098–3110, 2009     

Characterization and anticorrosive properties of poly(2,3‐dimethylaniline)/nano‐Al2O3 composite synthesized by emulsion polymerization

Poly(2,3‐dimethylaniline)/nano‐Al₂O₃ composite (PAC) was synthesized by emulsion polymerization using dodecyl benzene sulfonic acid as emulsifier and dopant. The structure of PAC was characterized by Fourier fransformation infrared spectroscopy, UV–visible adsorption spectroscopy, and field emission scanning electron microscopy. The thermal stability was studied by thermogravimetric analysis, and the electrochemical performances were studied by cyclic voltammetry measurements. Epoxy coatings containing PAC and poly(2,3‐dimethylaniline) (P(2,3‐DMA)), respectively, were painted on steel, and accelerated immersion tests were performed to evaluate the anticorrosion property of the coatings in 3.5% NaCl solution. The results showed that the addition of PAC and P(2,3‐DMA) could improve the anticorrosion performance of epoxy coating significantly and the PAC coating had higher corrosion resistance than that of P(2,3‐DMA). Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis and characterization of amphiphilic copolymer of linear poly(ethylene oxide) linked with [poly(styrene‐co‐2‐hydroxyethyl methacrylate)‐graft‐poly(ε‐caprolactone)] using sequential controlled polymerization

A well‐defined amphiphilic copolymer of ‐poly(ethylene oxide) (PEO) linked with comb‐shaped [poly(styrene‐co‐2‐hydeoxyethyl methacrylate)‐graft‐poly(ε‐caprolactone)] (PEO‐b‐P(St‐co‐HEMA)‐g‐PCL) was successfully synthesized by combination of reversible addition‐fragmentation chain transfer polymerization (RAFT) with ring‐opening anionic polymerization and coordination–insertion ring‐opening polymerization (ROP). The α‐methoxy poly(ethylene oxide) (mPEO) with ω,3‐benzylsulfanylthiocarbonylsufanylpropionic acid (BSPA) end group (mPEO‐BSPA) was prepared by the reaction of mPEO with 3‐benzylsulfanylthiocarbonylsufanyl propionic acid chloride (BSPAC), and the reaction efficiency was close to 100%; then the mPEO‐BSPA was used as a macro‐RAFT agent for the copolymerization of styrene (St) and 2‐hydroxyethyl methacrylate (HEMA) using 2,2‐azobisisobutyronitrile as initiator. The molecular weight of copolymer PEO‐b‐P(St‐co‐HEMA) increased with the monomer conversion, but the molecular weight distribution was a little wide. The influence of molecular weight of macro‐RAFT agent on the polymerization procedure was discussed. The ROP of ε‐caprolactone was then completed by initiation of hydroxyl groups of the PEO‐b‐P(St‐co‐HEMA) precursors in the presence of stannous octoate (Sn(Oct)₂). Thus, the amphiphilic copolymer of linear PEO linked with comb‐like P(St‐co‐HEMA)‐g‐PCL was obtained. The final and intermediate products were characterized in detail by NMR, GPC, and UV. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 467–476, 2006     

Well‐defined poly[(dimethylamimo)ethyl methacrylate]‐b‐poly(fluoroalkyl methacrylate) diblock copolymers: Effects of different fluoroalkyl groups on the solution properties

A series of well‐defined, fluorinated diblock copolymers, poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(2,2,2‐trifluoroethyl methacrylate) (PDMA‐b‐PTFMA), poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(2,2,3,4,4,4‐hexafluorobutyl methacrylate) (PDMA‐b‐PHFMA), and poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(2,2,3,3,4,4,5,5‐octafluoropentyl methacrylate) (PDMA‐b‐POFMA), have been synthesized successfully via oxyanion‐initiated polymerization. Potassium benzyl alcoholate (BzO^?K⁺) was used to initiate DMA monomer to yield the first block PDMA. If not quenched, the first living chain could be subsequently used to initiate a feed F‐monomer (such as TFMA, HFMA, or OFMA) to produce diblock copolymers containing different poly(fluoroalkyl methacrylate) moieties. The composition and chemical structure of these fluorinated copolymers were confirmed by ¹H NMR, ¹⁹F NMR spectroscopy, and gel permeation chromatography (GPC) techniques. The solution behaviors of these copolymers containing (tri‐, hexa‐, or octa‐ F‐atom)FMA were investigated by the measurements of surface tension, dynamic light scattering (DLS), and UV spectrophotometer. The results indicate that these fluorinated copolymers possess relatively high surface activity, especially at neutral media. Moreover, the DLS and UV measurements showed that these fluorinated diblock copolymers possess distinct pH/temperature‐responsive properties, depending not only on the PDMA segment but also on the fluoroalkyl structure of the FMA units. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2702–2712, 2009     

Preparation and characterization of poly(methyl methacrylate)/titanium oxide composite particles

Before polymerization, the introduction of double bonds onto the surface of the TiO₂ particles was achieved by the treatment of the TiO₂ particles with the silane-coupling agent. Via in-situ emulsion polymerization, the poly(methyl methacrylate) (PMMA)/titanium oxide (TiO₂) composite particles were prepared by graft polymerization of MMA from the surface of the modified TiO₂ particles. The structure of the obtained PMMA/TiO₂ composite particles was characterized using fourier transform infrared spectra (FT-IR), thermo-gravimetric analysis (TGA), differential scanning calorimetry (DSC) and size excluding chromatography (SEC). The morphology of the obtained PMMA/TiO₂ composite particles was observed by transmission electron microscope (TEM). The results of FT-IR and TGA measurements show that PMMA is successfully grafted from the surface of the TiO₂ particles and that the percentage of grafting and the grafting efficiency can reach 208.3% and 96.6%, respectively. At the same time, the TGA and DSC measurements indicate an enhancement of thermal stability. TEM images demonstrate a better dispersion of the TiO₂ particles in the composite latex. In addition, UV-visible absorption measurements show that the PMMA/TiO₂ composite particles can absorb over 95% UV light at 210–400 nm wavelength.     

Confocal microscopy studies of shear‐induced coalescence in blends of poly(butyl methacrylate) and poly(2‐ethylhexyl methacrylate)

This article reports the results of confocal fluorescence microscopy studies of shear‐induced coalescence in binary blends of poly(2‐ethylhexyl methacrylate) (PEHMA; 90 wt %) and poly(butyl methacrylate) (PBMA; 10 wt %). We prepared the blends by casting a mixture of latex dispersions of the components onto a substrate and allowing the film to dry under ambient conditions. The initial morphology of the film was a dispersion of 120‐nm PBMA spheres in a continuous PEHMA matrix. One‐fifth of the PBMA particles were labeled with anthracene, the emission of which we observed with confocal microscopy. The blends were sheared in a parallel‐plate rheometer at 80 and 100 °C for 1 and 10 h. Careful image analysis allowed us to estimate the mean size of the dispersed phase and the width of the size distribution. The results were compared with the theoretical limits of Wu and Taylor. After 10 h of shearing, the mean particle size decreased and the particle distribution became narrower in comparison with the results obtained after 1 h of shearing. We explain this result by inferring that before the sample reached steady‐state morphology, its rate of coalescence was greater than the rate of particle breakup. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2317–2332, 2001     

Modification of the ω‐bromo end group of poly(methacrylate)s prepared by copper(I)‐mediated living radical polymerization

Four different approaches to introduce a specific functional group at the ω terminus of poly(methacrylate)s (PMMAs) prepared via copper(I)bromide/pyridinalimine‐mediated atom transfer polymerization, under polymerization conditions, are reported. Method 1 involves the homolysis of the ω‐C Br bond with a subsequent reaction, via coupling or disproportionation, with an external radical species. The reaction with 2,2,6,6‐tetramethylpiperidin‐N‐oxyl shows a high conversion (>78%) of the ω‐bromo PMMA chains into their corresponding macromonomer analogues. Method 2 utilizes monomers that are able to undergo radical addition followed by subsequent fragmentation. Reactions with trimethyl[1‐(trimethylsiloxy)phenylethenyloxy]silane and allyl bromide show quantitative and 57% transformation, respectively. Method 3 is the reaction of a monomer that yields a relatively more stable secondary, or primary, carbon–halogen bond. Reactions with divinylbenzene, n‐butylacrylate, and ethylene showed quantitative, 62%, and quantitative additions, respectively. Method 4 is the addition of nonhomopropagating monomers, that is, maleic anhydride. This reaction proceeds quantitatively. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2678–2686, 2000     

Synthesis of pH‐sensitive surfactants by the terpolymerization of methacrylic acid,methoxy poly(ethylene glycol) methacrylate,and lauryl methacrylate: Initiator effect and reactivity ratio study

For the development of pH‐sensitive surfactants to be used in water‐in‐oil fermentation, the free‐radical terpolymerization of methacrylic acid (MAA), methoxy poly(ethylene glycol) methacrylate (MPEGMA), and lauryl methacrylate (LMA), at a molar ratio of 1.0:0.04:0.76, was studied with two initiators, azobisisobutyronitrile (AIBN) and hydrogen peroxide, at different concentrations. The polymer synthesized with 0.45% AIBN as the initiator was the most promising, giving similar conversions of all three monomers throughout the 10‐h polymerization. The subsequent study on AIBN‐initiated systems indicated that MPEGMA caused an increase‐then‐decrease profile of the MAA conversion with a plateau around an ethylene glycol/MAA ratio of 1–2. This observation was fairly consistent with the well‐known type II template polymerization of poly(ethylene glycol) (PEG)–MAA systems. The reactivity ratios obtained in this study suggested that the polymer synthesized with AIBN as the initiator had a structure of alternating blocks of MAA and LMA, with isolated PEG grafts. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2950–2959, 2004     

Synthesis of syndiotactic‐rich star‐shaped poly(methyl methacrylate) by core‐first group transfer polymerization using N‐(trimethylsilyl)bis(trifluoromethanesulfonyl)imide

The N‐(trimethylsilyl)bis(trifluoromethanesulfonyl)imide‐catalyzed (Me₃SiNTf₂‐catalyzed) group transfer polymerization (GTP) of methyl methacrylate (MMA) has been studied for synthesizing stereospecific star‐shaped poly(methyl methacrylate)s (PMMAs). The catalytic property of Me₃SiNTf₂ for the GTP of MMA using 1‐methoxy‐1‐trimethylsilyloxy‐2‐methyl‐propene as the initiator was confirmed by a kinetic investigation and matrix‐assisted laser desorption ionization time‐of‐flight mass spectrometry measurement. The initiating efficiency (f) of Me₃SiNTf₂ was 0.94–1.00, which was estimated by the value of M_n(calcd)/M_n(SEC). The Me₃SiNTf₂‐catalyzed GTP of MMA was carried out using initiators possessing three, four, and six MTS groups (MTS₃, MTS₄, and MTS₆, respectively) under the condition of [MMA]₀/[MTS₃, MTS₄, or MTS₆]₀ = 120 at ?55 °C. All the obtained PMMAs exhibited unimodal and narrow molecular weight distributions as M_w/M_ns = 1.03–1.04 and the M_w(MALS)s of the 3‐, 4‐, and 6‐armed star‐shaped PMMAs (PMMA₃, PMMA₄, and PMMA₆, respectively) were 12.9, 12.9, and 13.4 kgmol^?1, respectively, which fairly agreed with the calculated M_w(calcd) values. The syndiotacticities, rrs, of PMMA₃, PMMA₄, and PMMA₆ were in the range of 87–89%. The stereoblock synthesis of PMMA₃, PMMA₄, and PMMA₆ was performed by the first and second polymerizations at ?55 and 45 °C; the rrs of the first and second PMMA blocks were 87.0, 87.0, and 86.0% and 65.0, 65.0, and 64.0%, respectively. The glass transition temperatures (T_gs) were 118.1, 115.8, and 111.5 °C for the respective syndiotactic‐rich PMMA₃, PMMA₄, and PMMA₆ and 111.5, 109.7, and 107.6 °C for the respective stereoblock ones. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Temperature effects on spreading of water nano‐droplet on poly(methyl methacrylate): A molecular dynamics simulation study

In this article, the effect of temperature on the spreading behavior of a water nano‐droplet on poly(methyl methacrylate) substrate is investigated. The contact angle analysis illustrates that the spreading process occurs in a stage‐like manner and the increase in temperature causes a regime change from partial to total wetting. The interaction energy distributions show that there exist sites on the surface which could trap water molecules and provide a better path for other molecules to overcome the asperities. Estimations of the coefficients of self‐diffusivity suggest that temperature has a major effect in the reorientation stage, which results in the formation of the interfacial layer. In the second stage of spreading, temperature affects the process by providing sufficient energy for water molecules to overcome the interactions with the substrate. Therefore, this stage is controlled by the movement of water molecules on the surface and is highly influenced by their interaction with the surface asperities, strong interaction sites, and the carbonyl groups. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1532–1541     

Compatibility and thermal properties of poly(3‐hydroxybutyrate)/poly(glycidyl methacrylate) blends

Poly(3‐hydroxybutyrate) (PHB)/poly(glycidyl methacrylate) (PGMA) blends were prepared by a solution‐precipitation procedure. The compatibility and thermal decomposition behavior of the PHB/PGMA blends was studied with differential scanning calorimetry, thermogravimetric analysis, and differential thermal analysis (DTA). The blends were immiscible in the as‐blended state, but for the blends with PGMA contents of 50 wt % or more, the compatibility was dramatically changed after 1 min of annealing at 200 °C. In addition, PHB/PGMA blends showed higher thermal stability, as measured by maximum decomposition temperatures and residual weight during thermal degradation. This was probably due to crosslinking reactions of the epoxide groups in the PGMA component with the carboxyl chain ends of PHB fragments during the degradation process, and the occurrence of such reactions can be assigned to the exothermic peaks in the DTA thermograms. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 351–358, 2002     

Nano‐emulsion use for the synthesis of polyaniline nano‐grains or nano‐fibers

We report that nano‐emulsions can be creatively used as a morphology selective synthesis method to prepare not only nano‐grains but also nano‐fibers with high selectivity. Synthesis of the two different morphological materials was demonstrated using polyaniline synthesis as a model case. Polyaniline nano‐grains were synthesized from aniline molecules in nano‐size aqueous droplets as polymerization sites whose droplets were generated by inverse water‐in‐oil nano‐emulsion use, and polyaniline nano‐fibers were synthesized from aniline in aqueous nano‐dimensional channels as polymerization sites whose channels were generated by direct oil‐in‐water nano‐emulsion use containing high population of oil droplets. Using the approaches, we successfully synthesized nano‐fibers of 60 nm diameter with 0.5 µm length and also nano‐grains having diameter of 60–80 nm. The two different polymerization sites of nano‐scale dimension were made by changing the ratio among surfactant, aqueous aniline/HCl solution, and oil, i.e. organic solvent. We found the nano‐fibers synthesized from the channels formed by the direct oil‐in‐water nano‐emulsion have higher bulk electrical conductivity than the nano‐grains which were synthesized from the droplets formed by the inverse water‐in‐oil emulsion. We also found that the emulsion use allows us to use a room temperature synthesis unlike conventional synthesis methods which require to use ice bath temperature. Physical properties of both nano‐fibers and nano‐grains synthesized were characterized by Fourier transform infrared (FTIR), UV–Vis spectra, scanning electron microscopy (SEM), and four probes conductivity measurement. Copyright © 2009 John Wiley & Sons, Ltd.     

Stress–strain behavior of low‐density polyethylene/poly(methyl methacrylate) blends with modulated interfaces with a hydrogenated polybutadiene‐block‐poly(methyl methacrylate) diblock copolymer

The stress–strain diagrams and ultimate tensile properties of uncompatibilized and compatibilized hydrogenated polybutadiene‐block‐poly(methyl methacrylate) (HPB‐b‐PMMA) blends with 20 wt % poly(methyl methacrylate) (PMMA) droplets dispersed in a low‐density polyethylene (LDPE) matrix were studied. The HPB‐b‐PMMA pure diblock copolymer was prepared via controlled living anionic polymerization. Four copolymers, in terms of the molecular weights of the hydrogenated polybutadiene (HPB) and PMMA sequences (22,000–12,000, 63,300–31,700, 49,500–53,500, and 27,700–67,800), were used. We demonstrated with the stress–strain diagrams, in combination with scanning electron microscopy observations of deformed specimens, that the interfacial adhesion had a predominant role in determining the mechanism and extent of blend deformation. The debonding of PMMA particles from the LDPE matrix was clearly observed in the compatibilized blends in which the copolymer was not efficiently located at the interface. The best HPB‐b‐PMMA copolymer, resulting in the maximum improvement of the tensile properties of the compatibilized blend, had a PMMA sequence that was approximately half that of the HPB block. Because of the much higher interactions encountered in the PMMA phase in comparison with those in HPB (LDPE), a shorter sequence of PMMA (with respect to HPB but longer than the critical molecular weight for entanglement) was sufficient to favor a quantitative location of the copolymer at the LDPE/PMMA interface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 22–34, 2005     

Viscoelastic properties of poly(ε‐caprolactone) – hydroxyapatite micro‐ and nano‐composites

Various composites have been proposed in the literature for the fabrication of bioscaffolds for bone tissue engineering. These materials include poly(ε‐caprolactone) (PCL) with hydroxyapatite (HA). Since the biomaterial acts as the medium that transfers mechanical signals from the body to the cells, the fundamental properties of the biomaterials should be characterized. Furthermore, in order to control the processing of these materials into scaffolds, the characterization of the fundamental properties is also necessary. In this study, the physical, thermal, mechanical, and viscoelastic properties of the PCL‐HA micro‐ and nano‐composites were characterized. Although the addition of filler particles increased the compressive modulus by up to 450%, the thermal and viscoelastic properties were unaffected. Furthermore, although the presence of water plasticized the polymer, the viscoelastic behavior was only minimally affected. Testing the composites under various conditions showed that the addition of HA can strengthen PCL without changing its viscoelastic response. The results found in this study can be used to further understand and approximate the time‐dependent behavior of scaffolds for bone tissue engineering. Copyright © 2012 John Wiley & Sons, Ltd.     

Cu(0)/2,6‐bis(imino)pyridines catalyzed single‐electron transfer‐living radical polymerization of methyl methacrylate initiated with poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)

A series of 2,6‐bis(imino)pyridines, as common ligands for late transition metal catalyst in ethylene coordination polymerization, were successfully employed in single‐electron transfer‐living radical polymerization (SET‐LRP) of methyl methacrylate (MMA) by using poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) (P(VDF‐co‐CTFE)) as macroinitiator with low concentration of copper catalyst under relative mild‐reaction conditions. Well‐controlled polymerization features were observed under varied reaction conditions including reaction temperature, catalyst concentration, as well as monomer amount in feed. The typical side reactions including the chain‐transfer reaction and dehydrochlorination reaction happened on P(VDF‐co‐CTFE) in atom‐transfer radical polymerization process were avoided in current system. The relationship between the catalytic activity and the chemical structure of 2,6‐bis(imino)pyridine ligands was investigated by comparing both the electrochemical properties of Cu(II)/2,6‐bis(imino)pyridine and the kinetic results of SET‐LRP of MMA catalyzed with different ligands. The substitute groups onto N‐binding sites with proper steric bulk and electron donating are desirable for both high‐propagation reaction rate and C? Cl bonds activation capability on P(VDF‐co‐CTFE). The catalytic activity of Cu(0)/2,6‐bis(imino)pyridines is comparable with Cu(0)/2,2′‐bipyridine under the consistent reaction conditions. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4378–4388     

Relaxational behavior of poly(4‐tetrahydropyranyl) methacrylate

Complex permittivity of poly(4‐tetrahydropyranyl methacrylate) (P4THPMA) was measured by dielectric spectroscopy. The spectra obtained show several relaxation processes labeled as δ, γ, β, and α in increasing order of temperature. These processes have been characterized and assigned to specific molecular motions. Comparison of the dielectric activity obtained for P4THPMA with those reported for poly(1,3‐dioxan‐5‐yl‐methacrylate) (PDMA) and poly(cyclohexyl methacrylate) (PCHMA) was performed. In fact, these three polymers have similar chemical structures with aliphatic rings in the ester residue. However, significant differences between the dielectric behavior of these polymers have been observed. In addition, complementary molecular mechanic (MM) calculations have been carried out. The energy barriers obtained by these calculations lead to energy barriers which are in relatively good agreement with those derived from the dielectric measurement by means Arrhenius plots. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3135–3147, 2006     

Magnetic poly(2‐hydroxyethyl methacrylate‐co‐ethylene dimethacrylate) microspheres by dispersion polymerization

Crosslinked poly(2‐hydroxyethyl methacrylate)‐based magnetic microspheres were prepared in a simple one‐step procedure by dispersion polymerization in the presence of several kinds of iron oxides. Cellulose acetate butyrate and dibenzoyl peroxide were used as steric stabilizer and polymerization initiator, respectively, and ethylene dimethacrylate was a crosslinking agent. The resulting product was characterized in terms of particle size, particle size distribution, iron(III) content, and magnetic properties. In the presence of needle‐like maghemite in the polymerization mixture and under suitable conditions, magnetic microspheres with relatively narrow size distribution were formed. An increase in the particle size and, at the same time, a decrease in molecular weight of uncrosslinked polymers resulted, as the continuous phase became richer in 2‐methylpropan‐1‐ol. Coercive force of needle‐like maghemite‐containing particles was higher than that of cubic magnetite‐loaded microspheres. Coercive force increased with the decreasing iron content in the particles. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1161–1171, 2000